Rauscher & Reyhing GmbH

Condition: used, Year of construction: 2013, Used machine Year of manufacture: 2013 Condition: Functionally tested Equipment: Iodpfx Aozu T Sgsbpeif Base machine Extendable boom Joint milling unit 1801 Edge feed system, fully automatic 1903 Glujet 201 adhesive application system, cartridge Printing unit 1912-3, pneumatic Cutting unit 1918 Combination milling unit FR201 Pulling blade unit 1929 Chip collection box Surface pulling blade 1964 Location: Flörsheim Availability: Short-term

Condition: excellent (used), Casadei 350PM edger, Felder G263 Liquids Pre-milling cutters, Plate heating, Roller glue application, Pneumatic pre-trimming saw, Pressure rollers, Front-rear trimming saw, Top-bottom milling unit R1 – R2, Profiling cycle R1 Flat cycle, Machine length 230cm, Feed rate 7m/min, Max. component height 45mm, Max. edge thickness 2mm, Ijdpfx Abozu Nxvjpjif Used machine in very good condition Mileage 6,800 meters Purchase possible through leasing.

Condition: new, Year of construction: 2026, 0,4-8 mm Workingpiece thickness from to 8-60 mm Total length 4930 mm Iiodpfx Aszu A R Ssbpof Feed speed 10 m/min. Weight 1500 kg

Condition: excellent (used), BRANDT KDF 440, 1440 edger Iedpfxezuztfe Abpsif well-equipped, CNC-controlled units operated from the control panel Pre-milling cutters Plate heating Glue application with a roller Second tank included Pneumatic pre-trimming guillotine Pressure rollers Trimming balls for final cut Liquids Multi-milling unit (up/down) R1-R2 Corner rounding unit R1-R2 Multi-profile edging unit R1-R2 Straight edging unit Liquids Polishing unit Nesting package Max. element height 60 mm Max. veneer thickness in roll 3 mm Feed rate max. 14 m/min with corner rounding 11 m/min Very good condition for a used machine Original mileage 144,000 meters

Condition: used, Year of construction: 2010, Edge banding machine Manufacturer: Brandt Type: Optimat KTD 720 Year of manufacture: 2010 Isdpfx Abszuzlbjpsif Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2008, - with workpiece return - Edge thickness max: 20 mm - Board thickness: 8-60 mm - Feed rate max: 20 m/min - with groove milling unit One: Edge banding machine with return Manufacturer: Brandt Type: KDF 991 Year of manufacture: 2008 Workpiece return Manufacturer: Ligmatech Type: ZHR 05 Boomerang Year of manufacture: 2007 Technical data - Right-hand machine - Machine length: 8,260 mm - Ligmatech ZHR 05 length: 10,460 mm - Edge thickness max: 20 mm - Board thickness: 8-60 mm - Thickness of wound edge max: 3 mm - Workpiece width min: 60 mm - Feed rate max: 20 m/min - Stepless feed: material pressure zone adjustable via servomotor - Electromotive height adjustment - Infeed stop: adjustable via servomotor - Infeed stop for thin elements - Glue system for granules: glue pot above the feed chain - BRANDT glue system QUICKMELT QA 45 - Suitable for PUR adhesives Iedpfx Aszuyp Sobpoif - Magazine for single strips - Spray device, front, cleaning at the rear - Pre-milling unit - Preheating zone - End trimmers: 2 motors, pneumatically adjustable - Flush trimming: top + bottom, manually adjustable - Fine milling trimming unit: 2 motors, adjustable via servomotor R2 - Edge rounding unit: 4 motors, manually adjustable - Groove milling unit: manually adjustable with tilting function - Radius trimming blades: R2, pneumatically adjustable / Second set for R1 included - Flat trimming unit - Glue joint trimming blade - Cleaning fluid spray at the rear - Buffing unit - Solid wood edge sanding unit - Conformity marking: Including complete documentation and CE

Condition: used, Year of construction: 2010, - Application of release agent, top/bottom - Joint milling unit - Gluing unit - Trimming unit - Copy milling unit SKF-L - Profile trimming blade unit - Spray cleaning agent - Self-adjusting trimming blade unit - Buffing unit Single-sided edge banding machine Manufacturer: IMA Type: Advantage 310 Year of construction: 2010 Technical data Workpiece - Workpiece length: min. 150 mm - Workpiece width: min. 65* / 150 mm *at a max. workpiece thickness of 25 mm - Workpiece thickness: min. 8 mm, 12 mm with profile trimming blades max. 40 mm (with MFA 08.346), 60 mm (with SKF) - Smallest workpiece: 65 x 300 / 150 x 150 x 19 mm - Machining allowance per workpiece edge: 0 - 5 mm (observe max. chip cross-section) - Workpiece shape: right-angled - Material: chipboard, MDF - Surface material: direct coating (melamine resin paper), paper, film, veneer Edge material - Roll material without film: Paper edges & plastic edges: 0.3 - 3.0 mm Veneer edges: 0.5 - 3.0 mm - max. edge cross-section: 150 - 180 mm² - Cut edge strips: Strips: 3.0 - 8.0 mm - max. strip cross-section: 520 mm² - Edge height: min. 12 mm, max. 65 mm - max. upper edge overhang: 2 mm - Edge profiles Paper edge: approx. 0.4 mm, chamfer 15 Iodpezuyp Eofx Abpsif Plastic edge up to 3.0 mm, radius depending on the tool Strip up to 8 mm flush milling (with interchangeable motor on MFA) Machine - Constant workpiece projection from the chain track: 35 mm + edge thickness - max. trimming cross-section 520 mm² - Throughput width: min. 65 mm (with projection of 35 mm) - min. workpiece length in feed direction: 150 mm - Overall height (top edge of chain track): 940 mm - Unit side: on the left in feed direction - Pneumatic connection: approx. 7 - 8 bar Application of release agent, top/bottom Joint milling unit 08.379 and blowing nozzle - with 2 motors, each 4 kW, 9000 RPM, 150 Hz Gluing unit 283.1513 with oil bath gearbox - Adhesive output 0.8 l, 60 mm high, with quick-lock system - can be used for hot melt adhesive or PU adhesive - with single roll / strip magazine, roll diameter 800 mm - with 3 main pressure rollers and 3 counter pressure rollers Trimming unit 08.415 - pneumatically swiveling to 0 or 8 degrees - with 2 motors 660 kW, 400 V, 200 Hz, 12000 RPM - 2 HM trimming saw blades 160 x 3.5 x 22, Z=36 Copy milling unit SKF-L - with 2 motors 180 W, 400 V, 200 Hz, 12000 RPM - and 2 motors 400 W, 400 V, 200 Hz, 12000 RPM - 1 set of DP profile milling cutter I 80x12xHSK25-R, Z = 4, with HSK25 shank - Profile length in the feed direction: max. approx. 50 mm - Workpiece thickness: max. 60 mm - Working speed: max. approx. 20 m/min - Distance between 2 workpieces: min. approx. 400 mm - min. workpiece projection = 35 mm + profile depth Profile trimming blade unit 08.519 - For finishing a top and bottom milled quarter-circle profile Spray cleaning agent Self-adjusting trimming blade unit 08.521 - for removing hot melt adhesive residue from the edge area of the top and bottom of the workpiece Buffing unit 08.617-2 - with an upper and lower motor: 180 W, 50 Hz, 1400 RPM - 2 polishing pads 50 x 160 x 19 mm

Condition: used, Year of construction: 2009, - Edge material thickness: 0.3 - 3.0 mm - Paper, PVC, and ABS edge bands: 0.3 - 3.0 mm - Veneer: 0.5 mm - 3.0 mm - Wood strips: 0.8 - 20 mm - Edge height: 14 mm - 65 mm Isdpfezuyprjx Abpsif Single-sided edge banding machine Manufacturer: IMA Type: Novimat Contour/I/G80/790/L20 Year of manufacture: 2009 Technical data - Electronically controlled feed speed: 6-30 m/min - Edge material thickness: 0.3 - 3.0 mm - Paper, PVC, and ABS edge bands: 0.3 - 3.0 mm - Veneer: 0.5 mm - 3.0 mm - Wood strips: 0.8 - 20 mm - Edge height: 14 mm - 65 mm - Maximum edge overhang from above: up to 8 mm edge thickness - 5 mm, over 8 mm - 2 mm Workpiece size: - Minimum workpiece length in the feed direction: 150 mm - Minimum workpiece width: 25 mm, thickness: 65 mm - Minimum workpiece thickness: 8 mm (without profile trimming blades) or 12 mm with profile trimming blades - Maximum workpiece thickness: without corner copying, max. 60 mm (max. 40 mm with corner copying) - Smallest element: 150 mm x 150 mm or 65 mm x 300 mm Note: *65 mm with a maximum piece thickness of 25 mm The edge banding machine is equipped with: - Hand-adjustable guide rail for inserting workpieces - Trimming units 08.376, 2 motors, each with 4.5 kW, spindle speed 9000 rpm, 150 Hz - Heating unit for warming the workpieces - Gluing unit with drive 283.1513, featuring a tightly sealed oil pan, drive arranged with glue pot content of 0.8 l and glue application height of 60 mm, with a pneumatic quick-clamping system for hot melt and PU adhesives, magazine for edge banding rollers and strips, edge banding roller diameter 800 mm - Glue pellet preheating unit with automatic feeding of glue pellets from a 30 kg container. - Automatic preheating unit for PU cartridges with a weight of approx. 2.5 kg and a capacity of 8-10 kg/h - Trimming unit 08.42/30/B, pneumatic adjustment of the saw blades from 0 - 25°, 2 motors 660 W, 200 Hz with frequency inverter and braking function - Pre-milling unit 08.055, swiveling up to max. 30° - Multi-chamfering unit 08.342, 2 motors, 660 W, 400 V, 200 Hz, 12000 1/min - Cleaning agent dispenser - Profile trimming blades 08.519 - Surface trimming blade 08.521 for removing excess glue from glue joints - Buffing unit 08.617-2, 2 motors with 180 kW, 50 Hz, 1400 rpm - Groove/milling unit with one motor Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2005, - Automatic infeed table - KFA unit - Return system Used single-sided edge banding machine Manufacturer: IMA Type: Combima Systems / I/R751220/R3 1 single-sided combination machine for trimming, edge gluing and edge finishing of panel-shaped workpieces made of wood and/or wood-based materials. - Automatic infeed table - KFA unit - Return system Technical data "Workpiece": Workpiece length - min.: 238 mm - max.: 2350 mm Workpiece width - min.: 142 mm - max.: 800 mm Workpiece thickness: - min.: 8 - 40 mm Technical data "Strip" (only for longitudinal processing): Roll material: - Paper edge bands & plastic edge bands: 0.3 - 3.0 mm - Veneer edge bands: 0.5 - 3.0 mm Edge height: - min.: 14 mm - max.: 45 mm Technical data "Machine": Variable workpiece overhang from the chain conveyor (including edge with edge thickness 0.3-3 mm): - min.: 40 mm - max.: 80 mm - PC control ICOS open - Feed speed v=5-25 m/min, frequency-controlled drive - Inclined roller table as infeed section NC infeed system for front and carcass parts - for length and width-independent automatic workpiece feed in single-sided edge processing machines. Only for the production of strip material in the 2nd pass - An additional stop rail, adjustable via NC axis. Double milling unit 08.376: - Controllable - Motor 1 operating in the same direction and motor 2 operating in the opposite direction - Reserve space on the unit carrier for a double trimming unit with electrical pre-installation for 2 x 6.6 kW. - Heater 300 lg, 2x1.5 kW, for preheating the workpiece edge. - Gluing unit 04.1570 system for straight edges and adhesive application to the workpiece. The edge thickness depends on the magazine used and is max. 3 mm. - Adhesive application for workpiece thickness max. 50 mm - 2 pre-melting tanks for PU adhesive - 12-position edge magazine for roll material 0.3-3 mm thick. (8 slots up to 3 mm, 4 slots up to 1.3 mm) Vertical roll holder for 12 rolls: - max. roll diameter 850 mm - max. edge height 45 mm Iisdpszuypljfx Abpef - Trimming unit 08.42, for 2 motors mounted on the upper pressure bar - Pre-milling and milling unit with height sensor - with 1 motor 1000 W - Multi-profile / chamfer unit, with 2 motors 1000 W - Contour milling unit KFA 30 - Multi-profile drawing blade unit - Flat drawing blade 08.517 - Copy edging unit 08.604 - Edging unit 08.617-2 - Double milling stand 75.184, 1050 mm high, both stand sides can be used - Milling / profile milling / grooving unit 75.34 with 1 motor, without tool, 100 Hz, 6000 rpm - Milling / profile milling / grooving unit 75.34 with 1 motor, without tool, 100 Hz, 600 rpm - Motor spindle for the use of the Hydro-Format tool system - Return system, manufacturer Meinert Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2017, Edge banding machine Manufacturer: SCM Type: Olimpic K360 T-ER1 Year of manufacture: 2017 Technical data - Feed speed: 11 m/min - Edge thickness: 0.4 - 6 mm - Control: SCM control panel with display - Board thickness: 8 - 60 mm - Power supply: 400 V / 3~ / 50 Hz, 23 A - Min. workpiece: 140 x 90 mm Units Pre-milling - 2 counter-rotating diamond heads (up to 3 mm removal) EVA gluing unit Pressure zone with driven roller + 2 pressure rollers End trimming unit K-2 (straight / beveled, automatic switching) Flush trimming - flush, radius, chamfer Corner rounding R1/R2 Profile + surface scraper blade Polishing unit Anti-adhesive liquid system (2 liquids), edge roller feed Note: Iedpfx Abozuyk Nepeif The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2023, Edge banding machine Manufacturer: Biesse Type: Akron 1440 A Year of manufacture: 2023 Technical data - Panel height*: 10-60 mm - Edge height: 14-64 mm - Edge thickness from roll: 0.4-3 mm - Edge thickness in strip form: 0.4-12 mm - Panel overhang over the chain: 25 mm - Panel length: 140-3200 mm - Minimum panel width (at a length of 140 mm): 85 mm - Minimum panel width (at a length of 250 mm): 50 mm - Chain feed speed: 12 m/min - Distance between panels: 450-650 mm - NC axis package for automatic machine setup - Mounting kit for workpiece return Ijdpszuyk Ajfx Abpjif * Minimum panel height: 8 mm at a maximum edge thickness of 1.5 mm. Depending on the selected processing units. Maximum permissible feed speed: 12 m/min. Units Anti-stick spray unit ADZ02 Pre-milling unit RT02 - two high-frequency motors, each 1.8 kW, 12000 RPM Gluing unit VC-511 - Processing of EVA and PUR granular adhesive - Filling volume: 1.5 kg Pressure zone - 1 driven pressure roller 100 mm, with independently adjustable pressing pressure - 2 and 3 pressure rollers, not driven, 60 mm, with anti-stick coating, arranged conically in relation to each other and pneumatically adjustable Trimming unit IT-70-S - two high-frequency motors, each 0.8 kW, 12000 RPM - The trimming can be performed straight (0°) or at an angle in a range of 0 to 15°. - Anti-static/coolant spray device after the trimming unit Flush trimming unit RF02 - two high-frequency motors, each 0.65 kW, 12000 RPM Corner rounding unit - two high-frequency motors, each 0.65 kW, 12000 RPM - Corner rounding is possible for both workpieces with a straight edge profile and for postforming and softforming profiles at 90° and 180° corners. Edge scraping blade RB02 - Switching between two processing profiles is done manually. Glue line scraping blade RC02 Polishing unit SZ02 - two motors, each 0.37 kW, 2800 RPM Hot air blower PH-501 - Power: 2 kW - Infinitely adjustable temperature control Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2003, Single-sided edge trimming and gluing machine Manufacturer: IMA Type: AVM/K/I/G80/822/S3R3L20 Year of manufacture: 2003 For milling, edge gluing, and finishing for a standard groove - only for pre-shaped/pre-grooved doors and square-edged doors Left-hand machine (fixed stop on the left). Complete processing in 3 passes 1st pass: Processing of the top surface of the door (transverse processing) 2nd pass: Door long edge 3rd pass: Door long edge During the 2nd and 3rd passes, the protruding transverse edge from the 1st pass is milled off by using a co-rotating/counter-rotating milling process. Double groove gluing is only possible through modifications to the machine and subsequent manual finishing of the edge. Max. door thickness: - Straight edge: approx. 70 mm - Groove gluing: approx. 60 mm Stable machine frame as a support for aggregates and housing for electrical installation. Drive for feed speeds of approx. 5-25 m/min., mechanically infinitely adjustable. (not to be confused with processing speed) Continuous, plastic-coated strip-type conveyor chain, approx. 80 mm wide, with automatic central lubrication. Manually height-adjustable top pressure with a V-belt 80 mm wide and spring-loaded, ball-bearing guide rollers. Machine length approx. 10,900 mm Infeed table at the machine inlet. 1 horizontal, manually adjustable, unheated stop bar 1 joiner milling unit controllable, not swiveling, without sensing with 2 motors, each 3 kW Gluing unit for optional operation of straight edge or softforming gluing, Iiedozuykvepfx Abpof by changing the glue application. Edge material: - Strips: up to 1.3 mm - Roll material: 0.4-3 mm - Solid wood strips: 6 mm Strip length max.: 2550 mm Strip height: 14-80 mm (depending on glue application) with: - Side adjustment by hand for the pneumatically controlled glue application. - Height adjustment by hand -15mm downwards and up to +10mm upwards. 1 bell for the main pressure roller, manually adjustable 1 glue application 0.8L, max. edge height 70mm, straight edge with pneumatic quick-release, Chem-Coat coated, electronic temperature control 1 hot melt glue application 0.8L with quick-release, up to max. 80 mm high edge material, soft edge, Chem-Coat coated, with temperature control and control unit for the strip coating 1 automatic Quickmelt hot melt glue feeder with a heating power of 5.0 kW 1 2-fold magazine only for edge material up to 3.0 mm thick, can be manually attached to the single-roll magazine 1 groove forming pressing unit for pressing the edge material into the groove with: - an activation unit 15 kW for re-activating the edge material for groove forming - a pneumatically controlled forming shoe for the underlapping edge - a pneumatically controlled forming shoe for the entire groove - additional post-pressing rollers for the edge areas in the groove - an electro-pneumatic lateral retraction device for the entire pressing unit 1 horizontal adjustment with mechanical digital display 1 trimming unit for 2 motors mounted on the top pressure for trimming the front and rear edge/strip overhang, for trimming cuts flush or with a bevel. 1 milling unit for 2 motors with height sensing, side sensing, for pre-milling from below and above with 2 motors 1kW, 400V, 200Hz, 12,000 RPM, 30° swiveling 1 milling unit for 2 motors with height sensing, side sensing, for fine milling from below and above with 2 motors 660W, 400V, 200Hz, 12,000 RPM, 30° swiveling Note: The technical data and descriptions are copies of the original order

Condition: used, Year of construction: 2019, Edge banding machine Manufacturer: SCM Type: Minimax E10 Year of manufacture: 2019 Technical data Edge thickness (strip material): 0.4 - 3.0 mm Edge thickness with shear cutter at 80 mm edge height: 0.4 - 1.5 mm Edge thickness with shear cutter at 50 mm edge height: 0.4 - 2.5 mm Edge thickness with shear cutter at 45 mm edge height: 0.4 - 3.0 mm Edge height: 10 - 84 mm Workpiece thickness: 8 - 80 mm Minimum workpiece width: 50 mm Minimum edge length: 210 mm Minimum inner radius (concave) at 0.4 mm edge: 25 mm Minimum outer radius (convex) at 0.4 mm edge: 5 mm Feed speed: 4 / 8 m/min Processing temperature: 140 - 220 °C Edge feed Integrated shear cutter for cutting edge material from the roll. Roll table for holding roll material. Suitable for ABS edges, melamine edges, veneer edges, and other pre-fabricated edge strips. Gluing system Iiodezuykpjpfx Abpof Teflon-coated glue tank below the table top. Continuous glue circulation to prevent glue deposits. Fast heating time of approx. 7 minutes. Standby function with timer. Glue tank capacity: 1.5 liters. Pressure system Motor-driven glue application roller. One free-running pressure roller. Foot pedal for start and stop control of the working cycle. Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2017, Edge banding machine Manufacturer: Homag Type: Optimat KDF 440 C Year of manufacture: 2017 Technical data Workpiece thickness: 8 - 60 mm Edge material: 0.4 - 8 mm (depending on the equipment) Feed rate: 8 - 18 m/min (stepless) Workpiece length min. approx. 120 mm Workpiece width min. approx. 60 mm Glue application EVA hot melt adhesive, optionally PUR-compatible Glue reservoir Iijdpfxszuykco Abpef Teflon-coated, quick-change system possible Total connected load approx. 15 - 20 kW (depending on the equipment) Compressed air requirement: 6 - 7 bar Machine weight: approx. 3,000 - 3,800 kg Control system: powerControl / powerTouch CE marking Equipment: Joint milling Glue application Pressure zone Cut-off saw unit Milling unit top/bottom Corner rounding unit Scraping blade unit Edge finishing unit Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2009, Edge banding machine Manufacturer: IMA Type: Novimat/I/G80/650/R3 Year of manufacture: 2009 Technical data - Workpiece overhang from the chain conveyor: 38 mm - Feed width: min. 65 mm (with max. workpiece thickness of 25 mm) - Workpiece length in feed direction: 150 mm - Overall height (top edge of chain conveyor): 960 mm - Feed speed: approx. 6 - 30 m/min, electrically adjustable - Machine control system ICOS open compact Workpiece - Workpiece length: min. 150 mm - Workpiece width: min. 65 mm - Workpiece thickness: 8 - 40 mm (with edge trimming function) / 60 mm (without edge trimming function) - Smallest workpiece: 150 x 150 mm or 65 x 300 mm - Edge material: paper, plastic and veneer - Height: 14 - 65 mm - Roller material thickness: 0.3 - 3.0 mm (veneer edges limited to max. 1.0 mm) - Max. upper edge overhang: 5 mm Units Infeed area - Release agent applicator mounted at the top and bottom, not adjustable Edge trimming - 2 motors 4.5 kW, 150 Hz, 9000 rpm - incl. frequency inverter with braking function - Motor 1 counter-rotating - Motor 2 co-rotating Gluing unit VTG 3-6 - with one preheating nozzle 300 mm for preheating the workpiece edge - 6-position edge magazine for roller material 0.3 - 3 mm thick. - 1 driven main pressure roller and 4 pressure rollers, with scraper, pneumatically adjustable Glue application - with pneumatic quick-lock system - Chem-Coat coating - electronic temperature control - Volume 0.8 l Pre-melting tank approx. 1 l - Heating power 3 x 400 W - with EVA glue, approx. 7.0 kg/h - with filler-free glue, approx. 5.0 kg/h Cutting unit - 2 motors 660 W, 200 Hz - incl. frequency inverter with braking function - pneumatic pivoting 0+25 for straight and bevel cutting Ijdpfozuyi Esx Abpjif Flush trimming - 2 motors each 1000 W, 400 V, 200 Hz, 12000 rpm - with HSK 25 shank - incl. frequency inverter with braking function Multi-profile trimming unit - 2 motors each 660 W, 400 V, 200 Hz, 12000 rpm - with HSK 25 shank - incl. frequency inverter with braking function - for trimming 4 profiles - with stepper motor axes for horizontal and vertical positioning Contour trimming unit KFA x30 - 1 motor 500 W, 400 V, 400 Hz, 18000 rpm - Program-controlled conversion for up to 4 profiles - incl. fine positioning for different edge thicknesses Multi-profile scraping blade - Stepper motor axes for horizontal and vertical positioning - Scanning from above and below (max. 4 profiles) - Scanning from the side via pneumatic pressure Spray nozzles at the top and bottom for applying cleaning agents - fixed, not adjustable Surface scraping blade - with height sensing skid - electronically controlled horizontal positioning Buffing unit - 2 lower and 2 upper motors, 180 W, 50 Hz, 1400 rpm - 1st motor pair with cloth-sisal discs 50x160x19 mm - 2nd motor pair with polishing discs 50x160x19 mm - The motors operate in the same direction and are both tilted and pivoted in the feed direction. - Each motor can be individually adjusted vertically 2x NC-controlled grooving - 2 milling motors each 4.5 kW, 150 Hz, 9000 rpm - incl. frequency inverter with braking function - one manual 90-degree pivoting device from 180 -270 with co- and counter-rotating function - Horizontal, stepless adjustment with AC servo motor for grooving unit Workpiece return Note: The technical data and descriptions are copies of the order confirmation at the time. The information is for informational purposes only and is non-binding.

Condition: used, Year of construction: 2017, Edge banding machine Manufacturer: Biesse Type: Jade 240 Year of manufacture: 2017 Iiedpfxezuyixe Abpsf Technical data Note: [b]The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.[/i]

Condition: used, Year of construction: 2005, Edge banding machine Manufacturer: IMA Type: Advantage 600 Year of manufacture: 2005 Technical data - Joint milling - Gluing unit for thin and thick edges - Imprint zone - 2x edge trimmers - Flush trimming - Multi-function trimming unit (MFA) Iiodozuyirjpfx Abpof - Profile trimming blade - Surface trimming blade - Buffing - Return system at the upper pressure roller Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2010, 1. Edge banding machine Manufacturer: Homag Type: KAL 210 Ambition 2264 Year of manufacture: 2010 Technical data Release agent spraying system Joint milling unit (2 x 4 kW) Glue application A20 (granule/quick-melt system) Pressure zone with driven pressure rollers Miter saw HL84 (2 motors) Flush-/radius-/chamfer milling unit BF10/BF20 Iodpfjzuyilex Abpoif Corner copying unit FK11 (2 motors) Profile drawing blade PN10 Straight drawing blade for glue joint Buffing unit (polishing) Release agent and cleaning agent spraying system at the outfeed Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2006, - Edge milling unit 2 x 2.2 kW - Combi-melt gluing unit - Automatic edge magazine - Trimming unit 2 x 0.8 kW Iiedpfxjzuyifs Abpof - Flush trimming unit 2 x 0.7 kW - Fine milling unit 2 x 0.3 kW - 2 quick-change sets for fine milling - Automated copy milling unit 2 x 0.37 kW - 2 pull blades - 2 surface pull blades - 5-way spraying system - Fine buffing unit with cloth disc 2 x 0.2 kW Edge banding machine Manufacturer: OTT Type: Twister Technical data: Glue application: Hot-melt adhesive application roller with simultaneous and counter-rotating action Edge thickness: 0.3-10 mm Workpiece thickness: 8-60 mm Workpiece width: 70 mm - Minimum Workpiece length: 150 mm - Minimum Operating pressure: 6 bar Feed power: 3.0 kW Feed speed: 14-20 m/min. Electrical connection: 3 x 400 V, 50 Hz Extraction: at 20 m/s, 1 x 180 mm diameter = 35 m³/min. Air velocity: 20 m/s - Minimum Compressed air consumption: 300 liters/min. (approximate value) Equipment - Machining units: Joining: - 2 x 2.2 kW, n=14600, 250 Hz, two individually controlled spindles. Combi-melt gluing unit: - Top-mounted gluing unit with interchangeable hopper for processing EVA, PUR hot-melt adhesives, or standard cleaning granules, hopper volume 2.5 l Edge magazine: - Automatic edge magazine with optical monitoring for strip edges in fixed lengths Trimming: - 2 x 0.8 kW, n=12000, 200 Hz, automatic pivoting 0 / 5, 2 HM saw blades, 140 x 3.2 x 16 mm, z=34 Flush trimming: - 2 x 0.7 kW, n=12000, 200 Hz, single-sided, with 2 HM reversible blade cutter heads HF70, 70 x 20 x 16 mm, z=4 Fine milling (chamfer 15 / 30 / 45): - 2 x 0.3 kW, n=12000, 200 Hz, double-sided, with 2 HM reversible blade cutter heads HF70, 70 x 20 x 16 mm, z=4 AWSR (radius R2-R5): - 2 quick-change sets for fine milling, 2 x 0.3 kW, with 2 HM reversible blade cutter heads AR73 x 16 x 16 mm, z=3, R2-R5 Copy milling: - Automated copy milling with two separate spindles for machining end faces and longitudinal radii. Motor power: 2 x 0.37 kW, 12000 rpm, Tools: R1 - R3 Pull blade: - 2 HM pull bars, automatically adjustable Surface pull blade: - 2 HM pull bars with fine adjustment PU set: - 5-way spraying system, 2 x release agents, 1 x lubricant, 2 x cleaning agents, fine buffing unit with cloth disc Edge finishing: - 2 x 0.2 kW, n=2800, 50 Hz, oscillating brushes Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2000, Edge banding machine, single-sided Manufacturer: OTT Type: Pacific V 6-F Year of manufacture: 2000 Technical data: Edge thickness: 0.2 - 6 mm Workpiece thickness: 8 - 42 mm Workpiece width: min. 70 mm Workpiece length: min. 0 mm Feed speed: 12 m/min Electrical connection: 3 x 400 V, 50 Hz Extraction: 2 x 120 mm at 20 m/s Iodpjzuyh Uefx Abpsif Extraction capacity: m³/h Equipment, processing units: Edge trimming 2 x 1.5 kW, 12,000 rpm, 200 Hz two tool-controlled spindles Gluing unit Rapid heating tank with Melt-matic automatic edge magazine with optical monitoring for strip edges in fixed lengths Release agent spraying device Cutting unit 2 x 0.2 kW, 12,000 rpm, 200 Hz automatic pivoting 0 / 3 Flush trimming unit x 0.43 kW, 12,000 rpm, 200 Hz Radius trimming unit R2 - R5 2 x 0.3 kW, 12,000 rpm, 200 Hz 2 quick-change stations for trimming units Corner rounding trimming unit 2 x 0.3 kW, 12,000 rpm, 200 Hz Scraper blade 2 x carbide scrapers Smoothing unit 2 x 0.2 kW, 2,800 rpm, 50 Hz Weight: 2,000 kg Note: The technical data and descriptions are copies of the order confirmation from that time. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2021, - Edge joining unit - Teflon-coated gluing unit - Miter saw unit - Multifunction milling unit x-motion PLUS, flush and radius milling unit - Edge processing unit - Radius grooving unit - Polishing unit Edge banding machine Manufacturer: Felder Format4 Type: Tempora60.06LX Year of manufacture: 2021 Technical data Control system: x-motion PLUS Chain feed Feed speed: 10 m/min Drive motor: 0.75 kW (S6) - 1.1 kW (S6) Minimum workpiece length: 140 mm Minimum workpiece width: 70 mm The minimum workpiece width varies depending on the workpiece length, height, and surface texture. Rotary table edge magazine for edge banding material Diameter of the rotary table: 750 mm Edge thickness: 0.4 - 3 mm Pull-out frame Pull-out workpiece support, extendable up to 450 mm Upper pressure bar Manually adjustable workpiece height: 8 - 60 mm Edge feeder for edge banding and strip material Edge joining unit: 2.2 kW, diamond cutter Z2 Speed: 12,000 rpm, 2 x 1.1 kW Teflon-coated gluing unit for 1.5 kg of EVA or PUR granules Ready for use after only 10 minutes of heating time Tool-free quick-change system Pressing unit, pneumatically controlled 1 driven and 2 tapered pressing rollers form the pressing zone Shear cutter for edge banding material, 0.4 - 3 mm thickness Miter saw unit with two high-frequency motors 0.35 kW, 12,000 rpm Pneumatically swiveling 0 - 10 degrees Multifunction milling unit x-motion PLUS, flush and radius milling unit 1 high-frequency motor above and below, 0.75 kW, 12,000 rpm, each with 4 interchangeable cutters Iisdozuyh Iepfx Abpjf Edge processing unit For soft-forming and post-forming workpieces, for processing the end edge with 0.4 - 3.0 mm edge thickness and 10 - 60 mm workpiece height 2-axis motor-controlled radius grooving unit including pneumatic retraction function Polishing unit Above and below Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2009, - Edge trimming mills - Gluing unit for EVA hot melt adhesive - Pressure zone - Cutting unit - Copy milling - Pull blades - Deburring unit Edge banding machine Manufacturer: Homag Type: KAL 330/6/A3/S2 Year of manufacture: 2009 Technical data - Edge trimming mills - Gluing unit for EVA hot melt adhesive - Pressure zone - Cutting unit - Copy milling - Pull blades - Deburring unit Note: Iiedpfxozuyhzs Abpsf The technical data and descriptions are taken from the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2009, Edge banding machine with workpiece return system Manufacturer: HOMAG Type: PROFI KAR310/11/A20/S2 Year of manufacture: 2009 Technical data Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding. Isdpfx Aozuyhusbpjif

Condition: used, Year of construction: 2005, Single-sided edge banding machine Manufacturer: IMA Type: Novimat Systems/I/R75/1000 Year of manufacture: 2005 Technical data PC control - ICOS OPEN control system Feed rate 5-25 m/min, frequency-controlled Fence with electronic positioning control Adhesive application above and below Trimming unit with 2 motors, each 4.5 kW, 9,000 rpm, controllable. - Horizontally adjustable via axis Heating element approx. 300 mm long, 2x 1.5 kW Gluing unit - Adhesive application with pneumatic quick-lock system. - Automatic PU melting system Quickmelt for 2 kg cartridges - 32-position edge magazine (8 slots up to 3 mm / 24 slots up to 1.3 mm) Vertical roller holder for 32 rollers, max. diameter 850 mm Cutting unit on the upper pressure roller with 2 motors, each 200 W, 400 V, 12000 rpm. - Horizontal pneumatic swiveling 0-25 - With controllable side contact, for 3 edge thicknesses Trimming unit with 2 motors, each 1000 W, 400 V, 200 Hz, 12000 rpm. - Operating in counter-rotation. Multi-processing unit 08.348 - For chamfering or radius trimming of the upper and lower longitudinal edges, as well as for copying the front and rear workpiece edges. - Program-controlled adjustment for up to 4 profiles - 2 motors, each 660 W, 400 V, 200 Hz, 12000 rpm. Spray nozzles above and below for applying cleaning agents Multi-profile scraper unit - With stepper motor axes for horizontal and vertical positioning. - For 4 profiles. Straight scraper unit - With electro-pneumatic retraction device Iiedpfxezuyhns Abpsf Copying edge smoothing unit - With 4 smoothing motors, each 250 W - Smoothing unit with 2 lower and 2 upper motors, each 180 W, 50 Hz, 1400 rpm. Smoothing unit - For smoothing and eliminating the white haze on the trimmed PVC/ABS edges - With an upper and lower smoothing zone With workpiece return system LGIMATECH ZHR 05/L/145 - Air cushion table, inclined, 2 return belts with brushing devices from below. Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2010, - Equipped with ISAS 28-position edge magazine - PU gluing unit - With Boomerang return system Single-sided edge banding machine Manufacturer: Homag Type: KAL 310/7/A3 Year of manufacture: 2010 Technical data - Equipped with ISAS 28-position edge magazine - PU gluing unit - With Boomerang return system Edge trimming unit with 2 motors, each 3KW, 150 Hz, 9,000 RPM. Pneumatically controlled for pre-trimming PU gluing unit 34 with PU hot melt unit - capacity max. 6 kg/h Container size 2 kg. QA glue application unit Selectable edges from the ISAS 28-position edge magazine 4 pressure rollers Release agent spray unit, top and bottom Trimming unit WK 13, bevel / straight With 2 motors, each 0.4 KW, 200 Hz, 12,000 RPM. Electropneumatic adjustment of the trimming motors to 2 positions (flush trimming and with overhang) Pre-trimming unit with 2 motors, each 0.55 KW, 200 Hz, 12,000 RPM. With double-roller scanning. With electropneumatic adjustment Shaping trimming unit FK 11 - manual For processing the edge overhangs on the top and bottom edges of the workpiece, as well as for milling the front and rear edges With 2 motors, each 0.4 KW, 200 Hz, 12,000 RPM. Universal trimming unit UF 11 With motor 4 KW, 150 Hz, 9,000 RPM. Swiveling 90°, electropneumatically controlled With HSK 63 F collet for unlocking by push-button Profile scraping unit PN 10 Pneumatic adjustment for moving sideways out of the working area Finishing unit FA11 top/bottom Consisting of: Iijdpfxszuyhhs Abpef Glue joint scraping blade Cleaning agent application Buffing unit with 2 motors, height adjustment with the upper pressure Machine control via 19-inch touchscreen Return system BOOMERANG ZHR05 With air cushion table, angled, length 2,000 mm, width 1,000 mm Conveyor belt width 1,100 mm Workpiece parameters: Length 300 - 2,500 mm / Width: 60 - 1,100 mm or Length 300 - 800 mm / Width: 1,100 - 2,000 mm Thickness 8 - 60 mm For 4-sided processing: Min. part size: 300 x 300 mm / max. part size 2,000 x 800 mm With roller strip for supporting wider parts.