WillemsenMachines

Condition: used, Year of construction: 2001, Continuous press Manufacturer: Ligmatech Type: Optimat MDE 10 Hodpfxozuzxbo Albenr Year of manufacture: 2001 Technical data Body dimensions - Length: 300 - 2500 mm - Height: 300 - 1300 mm - Depth: 120 - 600/800 mm - Pressing forces are generated electrically, both horizontally and vertically, and can be varied independently - Pressing forces are applied vertically via a pressure plate and horizontally via 3 pressure jaws each - Pressing takes place centered and on a zero line on the operator side Positioning of the pressure jaws: - Top pressure jaw with forced guidance on the top press, optionally lowerable via cylinder - Middle pressure jaw freely programmable and motor-driven - Bottom pressure jaw freely programmable and movable via a common drive with the middle pressure jaw Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Hodpfxezuzw Do Albonr Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1996, Continuous press Manufacturer: OTT Type: 300-K-D0 Year of manufacture: 1996 Technical data Plate dimensions: 2550 x 1350 mm Hedpszuzwwofx Albjnr Hot water heating 6 pressure cylinders Total pressing force: 135 t Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2007, Lamination press Manufacturer: Dimter Type: PROFIPRESS L2500 Year of manufacture: 2007 Technical data Wood dimensions to be processed Wood width, panels: 30 - 150 mm Wood thickness: 11 - 60 mm Wood inlet length: 800 - 2500 mm Panel widths, variable: max. 1300 mm Specific pressing pressure for cross-sections of 2500 x 60 mm: up to 1.6 N/mm2 The pressing surface per press cycle must not be smaller than 100 cm2 Filling width of the press per cycle: min. 650 mm / max. 1300 mm Max. filling area of the press per cycle: 3.25 m2 (The max. usable press width depends on the widths of the individual lamellas.) Wood type Softwood/hardwood Press without options Electrical connection, press: 7 kW Electrical connection, 40 kW generator: 56 kW Operating voltage: approx. 400 Volt / 50 Hz (C/s) Collection table extended to 3700 x 1300 mm, with stainless steel wood support Motor-driven multi-function slider Lamination press Profipress L 2500 Press bed area approx. 2500 x 1300 mm Sturdy base frame with lower press table made of stainless steel as a grounding electrode Quick-change stop guide sets for panel thicknesses of 19 - 40 mm, which can be hydraulically adjusted to the current filling width Hydraulic special pressure elements ensure uniform pressure distribution over the entire joint length and compensate for tolerances In multi-lane operation, filling widths may vary by a maximum of 15 mm Upper pressure plate with hydraulic drive generates high vertical pressing pressure for minimal displacement Integrated hydraulic unit for generating pressing force and driving the hydraulic motors Control cabinet and control panel Protective cladding Additional individual pressure elements from above Automatic gluing station with precision gluing head Infeed for different widths Camera Hjdpfxszuzwqo Albenr Washing and rinsing device for gluing head Modem incl. software for online connection Note: The technical data and descriptions are copies of the order confirmation from that time. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2019, Corpus press Manufacturer: LINYI JIANZHONG WOOD MACHINERY Type: JJZ-CP Year of manufacture: 2019 The JJZ-CP press is suitable for the production of plywood, doors, and MDF panel joints. The feeding and removal of the glued elements are carried out automatically via powered roller conveyors. Technical data - Max. pressure 500 t (adjustable) - Max. filling height 1300 mm - Min. filling height 900 mm - Max. filling size 1300 x 2500 mm - Press dimensions 3600 x 1370 x 4500 mm - Press placement approx. 500 mm below floor level - Feeding table 2000 x 1960 mm - Receiving table 2350 x 2500 mm - Max. power 13.2 kW - Weight 12000 kg - CE marking - Capacity: 6 batches per hour 2 corpus presses are available for sale. Hedpjzuzwkefx Albonr Note: The technical data and descriptions are transcriptions from the original order confirmation. The data is for informational purposes only and is not binding.

Condition: ready for operation (used), Year of construction: 2022, operating hours: 2,044 h, controller manufacturer: SIEMENS, controller model: SINUMERIK 840D sl, laser power: 6,000 W, travel distance X-axis: 3,500 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 115 mm, number of axes: 3, This 3-axis TRUMPF TruLaser 5030 fiber L76 FMC was manufactured in 2022. It features a working format of 3,000 x 1,500 mm and a powerful 6000W solid-state disk laser. The machine includes an automatic longitudinal pallet changer and advanced cutting capabilities, such as adaptive lens systems and automatic nozzle changers. If you are looking to get high-quality fiber laser cutting capabilities, consider the TRUMPF TruLaser 5030 fiber L76 FMC machine we have for sale. Contact us for further details. • Working format/area: 3,000 x 1,500 mm; X 0–3,000 mm / Y 0–1,500 mm / Z 0–115 mm • Machine design: Closed machine frame; gantry drive with direct linear drives; automatic longitudinal pallet changer; integrated control cabinets and storage cabinet; working-area lighting; machine status light; water/air machine and laser chiller; CE compliant; ambient temp 5–35 °C • Dynamics/accuracy: Max simultaneous axis speed 280 m/min; Ps 0.03 mm; Pa 0.05 mm; min programmable increment 0.001 mm • CNC control: Siemens SINUMERIK 840D sl with 21.5" color MultiTouch; MultiTouch HMI; USB and RJ45; integrated technology data; programmable cutting gas/pressure; production planning; multi-sheet processing; automatic shutdown; Remote Support interface; Condition Guide; Cutting Guide; Central Link; Online Update Manager • Laser source: TRUMPF TruDisk 6001 (6 kW) solid-state disk laser; fiber-optic beam delivery; one LLK output; closed beam guidance; high back-reflection resistance; stable output over service life • Cutting head: Universal cutting unit; single cutting-head strategy; adaptive lens system; protective glass with online condition monitoring; auto nozzle centering; collision protection; capacitive height control; automatic focal position; pilot laser • Standard cutting functions: AdjustLine; BrightLine fiber; ControlLine; FastLine; FlyLine; FocusLine; NitroLine; PierceLine; Performance package; Highspeed cutting package; Copper and Brass cutting packages; Micro-weld • Additional cutting package: Highspeed Eco (fusion cutting, medium-thickness stainless steel) with up to 70% cutting-gas reduction and up to 100% sheet throughput increase • Automatic nozzle changer: 21 positions; automatic change/cleaning/re-setting tied to material/process; reduces setup/handling • Drop&Cut: Integrated camera; assigns live image of residual sheet to part geometry; live cutting preview; no separate programming needed for basic use • Process monitoring camera: Front-area monitoring (~2.5 m); remote observation; preliminary result assessment; video stream output to external monitor • Pallet/material handling (machine-integrated): Automatic longitudinal pallet changer; loading/unloading parallel to machining; pallet access from three sides Additional equipment • LiftMaster Compact 1530 (AL34) automatic loading/unloading system • Type 1530; max sheet 3,000 x 1,500 mm; min sheet 1,000 x 1,000 mm • Max sheet thickness 25 mm; max sheet weight 900 kg; max unloading weight 900 kg • With rake lifter: max thickness 25 mm; with rake lifter + belt system: max thickness 15 mm • Minimum part size with rake lifter: 150 x 150 mm • LiftMaster equipment/options • Storage connection; extended pallet travel out of machine Hnedpfxezuzwdo Albsr • Sheet separation device; double-sheet detection; synchronous loading • Thin-sheet separation (0.8–2.0 mm); loading station for 90 mm stack height • Structural-steel loading grippers, 67 mm pitch, replaceable tines

Condition: used, Year of construction: 1998, Continuous body press Manufacturer: LIGMATECH TYPE: MPP 15 Year of manufacture: 1998 The MPP 15 is a flexible press for batch-related production without setup times. The MPP 15 can be used individually or in various combinations in an assembly line. The pressing forces are applied pneumatically. The separately adjustable vertical and horizontal pressure allows for pressing both horizontal and vertical bodies. The vertical forces are transmitted through a plate, while the horizontal forces act on the body via press cheeks. Hodpozuzv Tefx Albonr The position of the center press cheeks can be adjusted using adjustable stops, allowing for different heights of bottoms and sides. During the infeed process, the body is measured photoelectrically, which automatically positions the horizontal pressure bar. Technical data: Body dimensions: Length: min. 300 mm / max. 2300 mm Height: min. 300 mm / max. 1220 mm Depth: max. 600/800/1000 mm (depending on the press type) Pressing pressure: vertical max. 17 kN horizontal max. 16 kN Working height: 500 mm Transport speed: min. 8 m/min. / max. 37 m/min. Pressing time: selectable up to 999 s Operating voltage: 400 V, 50 Hz Control voltage: 24 V DC (according to VDE) Required air pressure: 5...8 bar Air consumption: 120 NL/cycle Total connected load: 3 kW Weight: approx. 4 tons Required room height: 3000 mm Extended infeed belt as a staging area Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: new, Field of application: Construction Hedozuzv Hopfx Albjnr Drive: Track Manufacturer: Kubota AS

Condition: used, Year of construction: 2009, Adhesive application machine Manufacturer: Wirth Type: LW 120.5/1300 Year of manufacture: 2009 Technical data - Roller width: 1300 mm - 2 rollers (application + metering) Hnjdpfx Ajzuzvyslbjr Note: The outfeed conveyor shown in the pictures is not included. Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: good (used), Year of construction: 2008, operating hours: 7,348 h, fuel type: diesel, first registration: 06/2008, Model year: 2008 Number of cylinders: 6 Engine displacement: 200 cc Hnedpfx Aszuzvtjlber = Company information = Hello

Condition: used, Year of construction: 2000, Corrugated board press Manufacturer: Hüttenhölscher Year of manufacture: 2000 Technical data Voltage: 400 V Hnedpezuzvmjfx Albjr Current: 32 A Frequency: 50 Hz Compressed air: 6 bar Note: The technical data and descriptions are a transcript of the order confirmation from that time. The data is for informational purposes only and is not binding.

Year of construction: 2007, condition: like new (used), 457mm wide stainless steel belt with overlay Ashworth Omni grid Belt 95mm Product gap 155 Tier pitch Main drive - 4Kw 1600 diameter drum Goedhart Freon evaporator full cascading refrigeration pack included in a container Hnjdpfx Aljzuzvgjbjr More photos and spec upon request

Condition: good (used), Year of construction: 2007, travel distance X-axis: 400 mm, travel distance Y-axis: 350 mm, travel distance Z-axis: 400 mm, spindle speed (max.): 4,500 rpm, spindle speed (min.): 5 rpm, quill stroke: 60 mm, rapid traverse X-axis: 5 m/min, rapid traverse Y-axis: 5 m/min, total height: 2,000 mm, total width: 2,000 mm, total length: 2,000 mm, table width: 350 mm, table length: 650 mm, rotational speed (max.): 4,500 rpm, rotational speed (min.): 5 rpm, table load: 250 kg, overall weight: 1,900 kg, Equipment: rotational speed infinitely variable, Travel X/Y/Z 400/350/400 mm, spindle speed 5 - 4500 rpm stepless, motor 8,0 KW, spindle taper ISO 40, control Heidenhain TNC 124, table size 650x350 mm, hydraulic tool clamping, coolant device, spash guard, handwheel, tool holders, machine feet, manual Hnjdszuzu Nspfx Albsr

Condition: used, A range of second-hand spare parts, as well as complete units, control systems and switchboards for Weinig Unitec (and other brands), are always in stock. Please contact us. Sample images. Hnodpfszuzu Aox Alber

Condition: used, empty load weight: 7,370 kg, maximum load weight: 27,630 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 04/2022, next inspection (TÜV): 04/2027, loading space volume: 92 m³, suspension: air, tire size: 385/65 R22.5, Equipment: ABS, | Peischl sliding floor | SAF axles with disc brakes | 1 liftable axle | 6 mm floor | Remote control | Roll-over cover, standing platform | Toolbox | Spare wheel holder incl. spare wheel | Aluminum rims | Tare weight: 8,160 kg | Payload: 27,630 kg | Gross vehicle weight: 35,000 kg | Austrian vehicle | Good condition, valid inspection certificate until | Subject to errors, typos, and prior sale. Hodszuzuvepfx Albenr

Condition: good (used), functionality: fully functional, operating pressure: 320 bar, input voltage: 500 V, input frequency: 50 Hz, Mobile nitrogen filling unit for filling accumulators, replenishing gas pressure, or filling accumulator stations. 320 bar Hnedjzuzupopfx Alber

Condition: used, first registration: 08/2022, Sale exclusively to traders under exclusion of any warranty. Subject to errors and prior sale. Hsdpezuzuisfx Albjnr

Condition: used, Year of construction: 2001, Thermo-lamination system Manufacturer: BÜRKLE Type: FFAII 1300 Year of manufacture: 2001 Technical data: Working width: 1300 mm Panel dimensions Width: 200 - 1300 mm Length: 400 - 3000 mm Hodpfxjzuzt Se Albenr Thickness: 8 - 40 +/- 0.2 mm Film dimensions Width max. 1320 mm (lateral overhang up to 20 mm) Roll diameter 76 or 152 mm (3" or 6") Working height above floor: 940 mm System speed: 15 - 45 m/min Three-phase drive with vector control Operating side: right Panel feed: centered System configuration FFAII 1300 - Brush machine DBM (chain brushes) - Preheating and smoothing calender GKL, D = 500 mm - Thermo-oiler heater 36 kW - Hardener application machine DAH + complete hardener circulation system with monitoring - Transport section + IR zones with temperature sensors - Adhesive application machine DAK + automatic level sensing - Cooling unit for DOW cooling - Adhesive supply - Conical transport section TKE - Lamination calender EKM, D = 500 mm + film unwinding station + separating station + belt transport section with operator platform for FVE - Expansion shafts - Smoothing calender GKL, D = 500 mm at the inlet of the conveyor belt - Thermo-oiler heater 96 kW for lamination calender and smoothing calender - Central control cabinet - I.S.E. Optimat ISL 111 (year of manufacture 2004) Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2009, Painting system Manufacturer: Cefla Type: Easy 2000D Year of manufacture: 2009 Painting line consisting of: - Infeed conveyor with light barriers - Dust removal brush machine - Spray booth with two automatic spray arms, each equipped with six spray guns - Steel belt conveyor for collecting excess paint that does not adhere to the workpieces - Automatic transfer conveyor to the drying oven Hnsdpfozuzt Esx Albor - Three-chamber drying oven for painted parts - Outfeed conveyor from the drying oven Including: - Heat recovery unit (recuperator) - Extraction system for volatile substances - Dust extraction system for the infeed table Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2021, Painting system for edge surfaces Manufacturer: WIKOMA Painting of narrow edge surfaces Commissioned: 2021 Intended use: Spraying the edges of furniture panels arranged in stacks. Scope of delivery: - 2 spray booths - 2 hot air drying tunnels - 1 sanding booth - Chain conveyor Hsdpfezuztxjx Albsnr - Control cabinet The system was in operation until the end of June 2025. Note: The technical data and descriptions are a transcript of the order confirmation from that time. The data is for informational purposes only and is not binding.

Condition: excellent (used), BRANDT KDF 440, 1440 edger well-equipped, CNC-controlled units operated from the control panel Hnsdpfx Aozuztfolbor Pre-milling cutters Plate heating Glue application with a roller Second tank included Pneumatic pre-trimming guillotine Pressure rollers Trimming balls for final cut Liquids Multi-milling unit (up/down) R1-R2 Corner rounding unit R1-R2 Multi-profile edging unit R1-R2 Straight edging unit Liquids Polishing unit Nesting package Max. element height 60 mm Max. veneer thickness in roll 3 mm Feed rate max. 14 m/min with corner rounding 11 m/min Very good condition for a used machine Original mileage 144,000 meters

Condition: used, Technical details: Hnedpfx Aszuzr Ijlber table length: - mm table width: - mm table load: - t width: 1000 mm height: 1600 mm 3pieces available (price per piece) according to DIN 650:nach DIN 650: T-Nutenbreite a=27,5; h= 55; b= 49; c= 21 mm; Abstand der T-Nuten 200 mm Spannfläche: B: 1300 x H: 1600 x Dicke: 63 mm Bei Ihrer Anfrage beziehen Sie sich bitte auf die Anzahl der gewünschten Aufspannwinkel. *

Condition: used, Technical details: table length: - mm table width: - mm table load: - t width: 1200 mm height: 1600 mm 3pieces available (price per piece) according to DIN 650:nach DIN 650: T-Nutenbreite a=27,5; h= 55; b= 49; c= 21 mm; Abstand der T-Nuten 200 mm Spannfläche: B: 1300 x H: 1600 x Dicke: 63 mm Bei Ihrer Anfrage beziehen Sie sich bitte auf die Anzahl der gewünschten Aufspannwinkel. Hnodszuzrzopfx Albor *

Condition: like new (used), functionality: fully functional, input voltage: 380 V, input current: 105 A, input frequency: 50 Hz, continuous power: 55 kW (74.78 HP), Complete designation: NXP01055-A2H1SSS-A1A300000 +QGLM+FL23*DPAP+DLDE Input: Uin: 3~380-500V, 50/60Hz, 105A, 40°C Output: 3~0-UIn, 0-320Hz, 105A, 40°C Power: 55kW: 400Vac / 90HP (Ref.): 480Vac Hedpfx Ajzuzrujlbonr Complete documentation included This frequency inverter comes from a warehouse clearance and has never been put into operation.

Condition: used, Year of construction: 2009, Painting system The system consists of: SORBINI Smartcoater SP1 paint roller coating machine, year of manufacture 2009, approximately 3000 operating hours Roller coating and puttying machine Technical data - Working speed: 5-20 m/min - Workpiece width: max. 1350 mm - Workpiece thickness: max. 100 mm UV lamp control cabinet UV lamps SUPERFICI Model 2UVPLUS65, year of manufacture 1998, on a VENJAKOB conveyor belt, year of manufacture 1998, average number of operating hours 8500 Working area 1.5 - 7.5 m/min. Max. element width 1300 mm Dimensions (length x width) Lamps with conveyor belt: 5100 mm x 1700 mm (+ 600 mm motors) Rollers: 2200 mm x 2900 mm Control cabinet for UV lamp: 2000 mm x 800 mm Note: The technical data and descriptions are a copy of the original order confirmation. The data is for informational purposes only and is not binding. Hedpfxszuzrhs Albonr