All Vitres Sprl

Condition: used, mileage: 36,000 km, power: 375 kW (509.86 HP), first registration: 06/2023, fuel type: diesel, empty load weight: 16,000 kg, maximum load weight: 17,000 kg, overall weight: 33,000 kg, axle configuration: 6x6, wheelbase: 4,200 mm, brakes: engine braking, color: brown, driver cabin: sleeper cab, gearing type: automatic, emission class: euro6, suspension: steel-air, number of seats: 2, Equipment: ABS, additional headlights, air conditioning, all wheel drive, cabin, central locking, crane, cruise control, differential lock, fog lights, navigation system, onboard computer, parking heater, power assisted steering, seat heater, traction control, Vehicle location: in transit, StreamSpace, Mercedes PowerShift 3, large cab, 1x comfort seat, 1x bunk, seat heating, electric mirrors, heated mirrors, electric window left, electric window right, air conditioning, sun visor, cruise control, navigation system, electric roof, auxiliary heater, air horn, ABS (anti-lock braking system), traction control system (ASR), constant throttle, PTO, differential lock, fog lights, high beams, work lights, storage box, leaf/air suspension, crane behind cab, emergency stop, grab control, foldable, elevated seat, 2-point hydraulic support, 2x hydraulic extensions, green environmental badge. Wheelbase: 4200 mm Body: ARCHIVE IMAGE! Tractor unit with crane Palfinger Epsilon S260Z96 with crane cab 9t front axle, rear axle planetary gear 300, 13.4t Electronic braking system with ABS and ASR, ABS can be deactivated, drum brakes front and rear, stabilizer front axle and 1st rear axle, reinforced stabilizer 2nd rear axle, condensate monitoring for compressed air system, electronic parking brake, smoker package, seat belt monitor, lower comfort bed, electric stationary air conditioning, residual heat utilization, additional hot water heater, additional thermal insulation, reverse warning system, PSM 2nd generation, StreamSpace, rain sensor, light sensor, electric lifting roof, MirrorCam, comfort central locking, off-road driving mode, Mercedes PowerShift 3, PowerShift Advanced, Multimedia Cockpit, Remote Online, Remote Connect, pre-installation for toll recording, navigation system, transmission oil cooler, LED daytime running lights, reinforced engine mounts, refrigerator, high performance engine brake, skid plate under bumper, climate package, PTO MB 123-10c MPA N-/M-speed. Load diagram: 4m-5300kg, 5m-4230kg, 6m-3520kg, 7m-3000kg, 8m-2610kg, 9m-2300kg! Grab available at extra cost! Ncjdpfx Ajy Ummtshzjt Matching Doll timber trailer available for €36,900 net extra, see -9277-! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale and errors excepted!

Condition: ready for operation (used), Universal / Tool milling machine DECKEL FP 1 & 3-axis Heidenhain digital display -Very well-maintained, original condition -Travel ranges X/Y/Z 300x150x340mm Nedpfoy Ummmex Ahzoct -Speed range 40-2000 RPM -Automatic feeds / inputs in two axes -Vertical / horizontal milling capability -Tool holder ISO 40 -Fixed swivel table -3-axis Heidenhain digital display -Coolant system -Chip tray -Documentation Dimensions: L x W x H 1.1 x 0.8 x 1.7 meters / Weight 700 kg Errors and omissions excepted.

Condition: excellent (used), functionality: fully functional, mileage: 90,468 km, number of beds: 2, number of seats: 4, fuel type: diesel, gearing type: mechanical, color: white, chassis manufacturer: Ford, chassis model: Transit 2.0 Tdci, total length: 6,980 mm, total width: 2,320 mm, total height: 2,870 mm, axle configuration: 2 axles, emission class: euro6, fuel tank capacity: 80 l, overall weight: 2,785 kg, operation weight: 3,500 kg, steering wheel position: left, number of previous owners: 1, Year of construction: 2022, machine/vehicle number: WF0DXXTTRDPL71414, Equipment: ABS, air conditioning, airbag, bathroom, bunk beds, car registration, central locking, differential lock, electronic stability program (ESP), fog lights, full service history, lift bed, middle seating arrangement, onboard kitchen, parking sensors, power assisted steering, second-hand vehicle warranty, shower, single beds, soot filter, traction control, We offer flexible consumer credit options for easy and stress-free purchases! Our Etrusco is designed for adventurers who value comfort, safety, and reliability on the road. Spacious yet easy to handle, this motorhome is perfect for both weekend getaways and extended trips. 💰 Warranty and Money-Back Guarantee ✔ 1-year Indie Campers warranty 🛡️ ✔ Satisfaction guaranteed! Try it for 14 days, and if you’re not satisfied, we’ll refund your purchase price! ✔ Fully inspected and road-ready! Nsdpfxoy Ummgj Ahzoct What makes this motorhome special? ✅ Comfortable and spacious: measuring 698 cm in length, 232 cm in width, and 287 cm in height, it offers outstanding interior space and headroom. ✅ Reliable performance: Ford Transit 2.0 TDCi engine delivering 129 HP, manual gearbox, and front-wheel drive. ✅ All-season ready: equipped with gas heating, auxiliary heater, and air conditioning for maximum comfort. ✅ Essential safety features: includes ABS, ESP, tire pressure monitoring, power steering, and rear-view camera. ✅ Fully equipped interior: separate shower, hot water, toilet, DAB radio, central locking, and 4 berths with 2 beds (central + side layout). ✅ Convenient and user-friendly: white exterior, diesel engine, Euro 6 emission class, and fuel tank capacity up to 80 liters. Try Before You Buy Not sure if it’s right for you? You can rent the camper for a few days to test it before making your decision! Ready to be yours! This Etrusco is a highly sought-after model—book a viewing and make sure you don’t miss out! 📩 Contact us now to view our full stock!

Condition: used, functionality: fully functional, mileage: 109,140 km, power: 88 kW (119.65 HP), number of beds: 2, number of seats: 5, fuel type: diesel, color: white, first registration: 02/2020, chassis manufacturer: Fiat, chassis model: Ducato 2.3 Mjet, total length: 6,990 mm, total width: 2,320 mm, total height: 2,940 mm, axle configuration: 2 axles, emission class: euro6, fuel tank capacity: 90 l, overall weight: 2,910 kg, operation weight: 3,500 kg, steering wheel position: left, number of previous owners: 1, Year of construction: 2020, machine/vehicle number: ZFA25000002N46817, Equipment: ABS, additional headlights, air conditioning, airbag, all-season tires, bathroom, bunk beds, car registration, central locking, cruise control, differential lock, electronic stability program (ESP), fog lights, full service history, middle seating arrangement, non-smoking vehicle, onboard kitchen, seat heater, second-hand vehicle warranty, shower, single beds, solar array, truck registration, twin bed, We offer flexible consumer credit options for easy, stress-free purchases! The Atlas 5 motorhome delivers the perfect balance of space, comfort, and functionality. Whether you're planning a weekend getaway or an extended journey, this fully-equipped motorhome is designed to provide you with a premium travel experience! 💰 Warranty and Refund ✔ One-year warranty 🛡️ ✔ Satisfaction guaranteed! Try it for 14 days—if you're not satisfied, we'll refund your money! ✔ Fully inspected and ready to go! What makes this motorhome so special? ✅ Extremely spacious and comfortable – Measuring 699 cm in length and 294 cm in height, it offers a true home-on-wheels experience. ✅ Powerful and efficient – 2.3 Mjet diesel engine, 120 hp, manual gearbox, and Euro 6 emissions standard. ✅ Perfect for 5 people – With 5 seats and 3 beds, it's ideal for families or group trips. ✅ Fully equipped for comfort – Includes gas heating, auxiliary heating, air conditioning, and sanitary facilities with hot water. ✅ Safe and secure – Equipped with ABS, ESP, central locking, tire pressure monitoring, and rearview camera. ✅ Try before you buy – Not sure if it's the right choice? You can rent the motorhome for as many days as you like to get a feel for it and make sure it fits your needs perfectly. Start your next adventure now! The Atlas 5 motorhome is in high demand! Don’t wait—schedule a viewing and reserve it today. 📩 Contact us now to discover our full inventory! Nsdpfx Ajy Ummaohzjct

Condition: excellent (used), axle configuration: 3 axles, permissible axle load (axle 1): 9,000 kg, permissible axle load (axle 2): 9,000 kg, permissible axle load (axle 3): 9,000 kg, first registration: 05/2019, total length: 14,040 mm, total width: 2,600 mm, wheelbase: 8,910 mm, color: other, Year of construction: 2019, Axle configuration Ncedjy Uml Nspfx Ahzst Rear axle 1: Lift axle; Max. axle load: 9000 kg Rear axle 2: Max. axle load: 9000 kg Rear axle 3: Max. axle load: 9000 kg Weights Empty weight: 8.513 kg Carrying capacity: 33.487 kg GVW: 42.000 kg Functional Cooling engine: diesel and electric (7279 operating hours diesel; 1457 electric) Maintenance, history and condition APK (MOT): tested until 10/2026 Technical condition: very good Visual appearance: very good Identification Registration number: OR-40-XG = Dealer information = Do you have any questions or suggestions? Please feel free to contact us. We guarantee a response within 8 hours. Prices do not include VAT. No rights may be derived from the information provided. Office phone number: Mobile: Dutch - English - German - French - Spanish - Italian) Available via WhatsApp and Viber. Mobile: Available via WhatsApp and Viber. When paying by bank transfer, the funds must be transferred to our bank account listed below. Always verify the payment details on our website. Please contact us if you have received different information. If in doubt, please call us so we can verify the invoice and/or payment. Bank details: Bank name: ING Bank address: Bijlmerdreef 106 1102 CT Amsterdam IBAN number: NL97INGB0117176699 EORI/VAT/TAX: NL810574901B(01) BIC/SWIFT: INGBNL2A

Condition: good (used), mileage: 273,083 km, power: 300 kW (407.89 HP), first registration: 04/2012, fuel type: diesel, axle configuration: 8x2, fuel: diesel, brakes: engine braking, color: blue, driver cabin: day cab, gearing type: automatic, emission class: euro5, suspension: other, Year of construction: 2012, Equipment: AdBlue, Bluetooth, EBS, air conditioning, cruise control, electric window regulation, electronic stability program (ESP), fog lights, power mirror, soot filter, trailer coupling, = Additional Options and Accessories = - Aluminum fuel tank - Brake booster - EPS (Electronic Power Steering) - Low noise Ncjdpfsy Uml Ajx Ahzst - Particle filter - Rearview camera - Side door - Toolbox = Additional Information = Axle Configuration Front axle 1: Steered; Suspension: Leaf spring Front axle 2: Steered; Suspension: Leaf spring Rear axle 1: Suspension: Air suspension Rear axle 2: Suspension: Air suspension Weights Unladen weight: 16,680 kg Payload: 19,320 kg GVW (Gross Vehicle Weight): 36,000 kg Maintenance, History, and Condition APK (Technical Inspection): Valid until 02/2027 Technical condition: good Optical condition: good Vehicle number: DAF CF 85.410 Tipper with Crane Tipper + Crane Epsilon Q150 / Euro 5 EEV .: XLRAK85MC0E940365 Suspension: Leaf / Air (Steering/Lift axle) Transmission: Automatic Air conditioning Engine brake Steering/Lift axle EURO 5 EEV Crane: Brand: EPSILON Type: Q150Z95TR Year: 2012 No liability for printing and typographical errors, changes, prior sales and errors. = Company Information = No liability for printing and typographical errors, changes, prior sales and errors. Al Shogran GmbH An der Glashütte 15 41516 Grevenbroich Tel.: Mobile: Ms. Sabine Faust Email:

Condition: ready for operation (used), Year of construction: 2000, travel distance X-axis: 2,200 mm, travel distance Y-axis: 600 mm, table width: 650 mm, table length: 2,600 mm, table load: 2,300 kg, overall weight: 12,000 kg, spindle speed (max.): 6,000 rpm, spindle motor power: 28,000 W, tool weight: 10,000 g, number of axes: 3, This 3-axis IBARMIA ZV 40 L2200 vertical machining centre was manufactured in 2000. It features an X-axis travel of 2200 mm, Y-axis travel of 600 mm, and Z-axis travel of 600 mm. The machine has a maximum table load capacity of 2300 kg and a rapid traverse rate of 30 m/min. If you are looking to get high-quality machining capabilities, consider the IBARMIA ZV 40 L2200 machine we have for sale. Contact us for further details. Ncodpfx Aey Umlpjhzot - X-axis travel in 2-station machining (shuttle operation): 720 mm- Z-axis travel (vertical): 600 mm (Optional: 800 mm)- Number of T-slots: 5- T-slots size: 18 mm- Distance between T-slots: 125 mm- Min./Max. distance spindle nose to table: 200 / 800 mm (Optional: 1000 mm)- Tool taper / holder: SK40 - DIN 69871 (Options: HSK A-63 DIN 69893 or HSK A-80 DIN 69893)- Pull stud for SK tool holder: DIN 69672- Clamping force of tool retention (SK): 12000 N (Options: HSK A-63: 18000 N / HSK A-80: 28000 N)- Inner bearing diameter: 80 mm- Max. standard spindle speed: 6000 rpm (Options: 4000 / 8000 / 10000 rpm)- Main spindle motor power at 100%: 28 kW (Intermittent: 38.5 kW)- Constant power for standard configuration from: 1500 rpm- Max. torque at 100%: 178 Nm (Intermittent: 245 Nm)- Feed force in X, Y, Z at 100%: 13000 N (Intermittent: 15600 N)- Rapid traverse rate in X, Y, Z: 30 m/min- Max. working feed rate in X, Y, Z: 10 m/min- Positioning tolerance Tp X(1000mm)-Y-Z: 0.015 mm- Max. positioning scatter Ps max.: 0.010 mm- Measuring system in X-Y-Z: Linear glass scales- Milling capacity in steel (St 60): 650 cm³/min- Drilling capacity in steel (St 60): Ø 60 mm- Tapping capacity in steel (St 60): M-36- Number of tool pockets: 24 (Options: 40 - 52)- Max. tool length: 300 mm- Max. tool weight: 10 kg- Max. tool diameter (full magazine): 85 mm- Max. tool diameter (adjacent pockets free): 125 mm- Tool management: Random- Tool change time: 3.5 s- Chip-to-chip tool change time: 7 s- Floor space requirement: approx. 17 m²- Coolant tank capacity: 370 liters- Machine length (Dimension A): 4200 mm- Textured paint structure (2 colors): RAL grey 7037 / blue 5012- Electrical connection: 55 kW- Operating voltage: 400 V / 50 Hz- Compressed air connection: 6 bar- Coolant pump power: 0.75 kW- Standard equipment: CE machine enclosure protection, chip conveyor, coolant tank, linear glass scales in X/Y/Z axes, vertical interior cladding along X-axis, workspace lighting, automatic centralized lubrication, hydraulic counterweight balance for spindle head, automatic pneumatic spindle cleaning, mobile control panel, rigid tapping (tapping without compensation chuck).- Factory options available: Internal coolant supply (IKZ), full machine enclosure, partition wall for shuttle operation, dividing heads/rotary tables for 1 or 2 additional machine axes, work tool touch probe, digitization systems, tool monitoring systems, portable electronic handwheel- depending on the requirements, parts in the Y-axis would need to be replaced or repaired

Condition: good (used), Polar Mohr 115 XT Paper Cutting Guillotine This machine is in very good condition, ready for production, after a service inspection. Low mileage. Year of manufacture: 2010. This is the most valued guillotine brand, a flagship product. A jogging and elevator are available for retrofitting. Technical specifications: Cutting width: 1150mm Stack height: 165mm Programmer with a 15″ color touchscreen display Air table Photocells Chrome table surface Ball screw drive for the rear comb Ncedpfsy Umkxsx Ahzst Optical cutting line Enlarged side tables Knife change via the control panel Additional rear table guards Weight: 3200kg 380V power supply Includes documentation, a tool kit, a tapping block, a spare knife, and one knife in the machine.

Condition: good (used), ML-800 NXL Die-Cutting Machine This machine is used to cut shapes from a mold (die) from materials such as paper, cardboard, leather, plastics, etc. The machine is in perfect condition, manufactured in 2018. First installed in 2020. This is the heaviest die-cutting machine in this format, precise. Format: 830 x 560 mm Weight: 2500 kg Power supply: 380 V Motor: 2.5 kW Equipment: – Electromagnetic clutch and brake – Quick-mount frame – 3 operating modes: continuous, time-delayed, and manual – Centralized pressure lubrication – Additional safety guards – Operating tools and instructions with CE documentation. Nedjy Umkrspfx Ahzect

Condition: used, Year of construction: 2008, operating hours: 5,834 h, 2008 | Delmag SR 25 BT / RH 18 on Sennebogen with ABI MDBA 3500 Soil Improvement Rig | Used Drill | 5834 hours 📍Location: Germany 🚛 Delivery available to your destination – Use our shipping calculator to estimate transport costs! 💰 Buy Now for EUR 74500 or Make an Offer. Payment at delivery available for an affordable fee (subject to approval)* 👷‍♂️ Inspected by an independent expert 65 inspection points 65 approved ✅ 0 imperfect ℹ️ 0 issues ⚠️ 📌 Inspector's Comment: Machine for concrete pile drilling, soil improvement, and vibrocompaction. Carrier device Sennebogen SR25BT (manufactured in 2008) with drilling attachment Delmag RH18 (manufactured in 2009). Drill table stroke 12.50m, total height 19.91m. Outreach 3.165 - 4.00m. Feed winch, winch for feed with freewheel, auxiliary winch, rear platform. Drill table SHT25, THE KDK ROTARY DRILL HEAD BT180-2 IS NOT PRESENT, PURELY A SOIL IMPROVEMENT DEVICE, drilling gearbox MBDA 3500 ABI. With single auger. NO Kelly bar. Mast support cylinder, automatic alignment. Hydraulic telescopic undercarriage with a width from 3.0m to 4.40m. The CAT C9 engine was overhauled by CAT in 2015 at BH 3.304. Drills and drilling accessories are available separately. Also available is a mobile mixing plant, brand MAT, consisting of a mixing container (throughput capacity 20m3/h), conveyor screw, mixing tank (capacity 4,000l), and plunger pump with remote control. The condition of the machine corresponds to the value of the operating hours. At the time of inspection in 2023, the machine was running/functioning without any abnormalities. As of October 2024, storage damages have occurred to valves, control, and hydraulic hoses. It is not possible to operate the machine with 2 attachments at the same time. The machine shows wear and tear appropriate to its age, mileage, and purpose of use on pins and bushes as well as signs of use (dents, abrasions, etc.). The machine was not tested under load. The machine was used with 55 and 80 paddles. After service and maintenance of the storage damages, the device is ready for use. Ncjdpfxsy Umklo Ahzjt 📄 Want to see the full inspection, extra photos, or a video? Tip: The reference "40844 Equippo" is commonly used when looking up more details online. 💡 Why this machine and our service stands out: ✔ Thorough inspection by professionals ✔ Jobsite delivery available ✔ Money-Back Guaranteed ✔ Secure and flexible payment options 🔄 Considering other equipment options? We offer helpful tools and resources for all equipment owners and operators – easily accessible on our platform.

Condition: good (used), TYMC-800 Honeycomb Hot Foil Stamping Machine The latest version, with a honeycomb plate for locks. The machine is designed for hot foil stamping, hot stamping, and standard die cutting without having to remove the hot plate. The machine is brand new and comes with a warranty. Format: Die-cutting 830x590mm Gold plating 800x540mm Weight 3000kg Operating speed 25 cycles/min Foil feed 1-500mm Operating temperature 20-150°C Power supply 380V Equipment: – Electromagnetic clutch and brake – Quick-assembly frame – Control panel with touchscreen PLC programmer – Two independent feeds, controlled by stepper motors – 3 operating modes: continuous, time-delayed, manual Nsdpfx Ahoy Umkfszect – Four independent heating systems, saving energy – Central lubrication – Additional safety guards – Photocells – Operating tools and instructions, CE declaration – Pressure plate Machine available immediately We provide installation and training (individual pricing) 12-month warranty. The machine is brand new. Our machines are among the few that meet all the standards required for operation in Poland. Testing is available at our showroom in Radom.

Condition: ready for operation (used), Title:TRANE RTHF 295 HSE – 1000 kW Water-Cooled Industrial Chiller | R1234ze | Dual CompressorHeadline: High-capacity Trane RTHF 295 HSE water-cooled industrial chiller engineered for demanding industrial applications. Featuring 1000 kW cooling capacity, dual Trane screw compressors, and low-GWP R1234ze refrigerant — a sustainable, energy-efficient, and reliable solution for large-scale industrial cooling TECHNICAL SPECIFICATIONS Specification Value Brand / Model TRANE RTHF 295 HSE Type Water-Cooled Industrial ChillerCooling Capacity 1000 kW (860,000 Kcal/h) Compressors 2 × Trane CHHC1C2D0P0 (Screw Type) Evaporator Shell & Tube Condenser Shell & Tube Water Flow Rate 172 m³/ h Refrigerant R1234ze (Low GWP) Control System Trane Adaptive Control Dimensions (mm) 4800 × 1800 × 2200 Weight 7,500 kg Location Seyhan / Adana, Türkiye UNIT CONDITION Fully operational and ready for immediate use Pre-delivery performance testing conducted prior to shipment Commissioning support available Performance test reports provided upon request TECHNICAL ADVANTAGES High-Capacity Performance: 1000 kW cooling power optimized for heavy-duty industrial loads Dual-Compressor Configuration: Staged operation enables superior energy efficiency under variable load conditions Low-GWP Refrigerant: R1234ze ensures compliance with European F-Gas regulations and sustainability targets Shell & Tube Heat Exchangers: Robust construction for long service life and ease of maintenance Trane Adaptive Control: Precise capacity modulation and operational stability Global Brand Reliability: Worldwide access to spare parts and technical support APPLICATION AREAS Industrial manufacturing facilities Plastic injection moulding and extrusion processes Concrete batching plants Food processing and cold storage Chemical and process industries Data centres and high heat-load environments Textile and paper mills THE ÖZSAYIN ADVANTAGEWith over 40 years of expertise in industrial cooling, we deliver more than just equipment — we provide complete turnkey solutions: Chiller sales and rental services Refurbishment and remanufacturing Compressor overhaul and maintenance On-site service and technical support Extensive spare parts inventory Engineering and project consultancy WARRANTY & RELIABILITY All units tested prior to dispatch Commissioning support available Performance test reports provided upon request, DELIVERY & PROCESS Fast delivery from stock Nationwide shipping across Türkiye Full export and customs documentation support CONTACT Mr. Samet Özsayın – Özsayın HVAC Technologies Seyhan / Adana, Türkiye HASHTAGS / KEYWORDS Nodpfx Ahey Umi Uozoct #ozsayin #chiller #industrialchiller #trane #watercooledchiller #r1234ze #screwchiller #1000kw #lowgwp #sustainablecooling #hvacturkey #chillerrental #tranertgf

Condition: excellent (used), max. wheel diameter 200 mm gear width 300 mm module 0,5 - 25 Ncjdpey Umi Iefx Ahzot centre distance 750 mm weight of the machine ca. 0,2 t dimensions of the machine ca. 0,8 x 0,6 x 0,6 m worm testing roll-machine

Condition: excellent (used), max. wheel diameter 130 mm gear width 180 mm max. module 2,5 min. module 0,3 turning speeds 140 - 900 U/min Nsdpfxey Umizo Ahzoct min. number of teeth 4 clamping length max. 200 mm Control Siemens max. workpiece diameter 80 mm total power requirement 3,5 kW weight of the machine ca. 2,9 t dimensions of the machine ca. 1,8 x 1,6 x 1,9 m

Condition: like new (used), Morgana Autocreaser 33 automatic creaser Ncedpfx Aoy Umiuehzst The device is in very good condition. A modern device that allows you to create a crease (groove), thanks to which we can bend paper or other materials more easily. Sheet size 330x900mm Weight: 400gsm programmer Weight: 150kg Manufacturer: Morgana, UK Image Creasing: Yes Creased materials: paper, cardboard, cardboard

Condition: used, Mitsubishi FCA335L22-1 CNC Control System – Complete Unit For sale is a used Mitsubishi CNC control system, model FCA335L22-1, removed from an industrial machine. The unit is offered exactly as shown in the pictures. Technical Details Manufacturer: Mitsubishi Electric Model: FCA335L22-1 Ncjdpfsy Uminjx Ahzst Serial Number: M3ZR422039Z Date Code / Year: 1992 Made in Japan Included Modules MC712 MC116 MC446-1 MC724-1 Multiple MC323 cards Integrated floppy disk drive Various interface and communication boards Condition Used condition Removed from industrial environment Visible signs of use, dust, and storage wear Untested / functionality unknown Sold strictly as spare parts, repair unit, or for refurbishment Scope of Delivery Exactly as shown in the photos No additional software, cables, or documentation included Suitable for: Machine retrofit projects Spare parts replacement Repair and maintenance of older Mitsubishi CNC systems

Condition: used, thickness of jaw / mm Precision Machine Vise / Toolmaker’s Vise – Heavy Duty Industrial Model For sale is a high-quality precision machine vise in solid industrial design. Perfect for milling machines, grinding machines, toolmaking, or other precision clamping applications in workshops and industrial environments. This vise features a robust construction, precise guide system, and strong clamping force. The hardened and ground jaws include prism inserts, allowing secure clamping of round workpieces as well. Details: Heavy-duty steel construction Ncjdpfxjy Umiho Ahzst Precision-ground clamping surfaces Hand crank spindle drive Prismatic jaws Very stable and heavy industrial design Ideal for toolmaking, milling, grinding machines, etc. Used, fully functional Normal signs of use (see pictures) Condition: Technically in perfect working condition. Cosmetic wear consistent with age and use, but overall in good condition. Scope of Delivery: Machine vise as shown in the pictures

Condition: used, thickness of jaw / mm Mechanical Precision Machine Vise with Hand Crank – Heavy Duty Industrial Model High-quality mechanical precision vise with manual hand crank operation. Ideal for milling machines, grinding machines, and toolmaking applications. Heavy-duty industrial construction Mechanical clamping system (non-hydraulic) Smooth manual hand crank Precision-ground jaws with prism profile Used, fully functional condition Ncsdoy Umibjpfx Ahzjt Normal signs of industrial use Scope of delivery exactly as shown in the pictures.

Condition: used, thickness of jaw 160 mm Precision Machine Vise / Toolmaker’s Vise with Hand Crank – Heavy Duty Industrial Model For sale is a high-quality precision machine vise in solid industrial design. Perfect for milling machines, grinding machines, toolmaking, or other precision clamping applications in workshops and industrial environments. This vise features a robust construction, precise guide system, and strong clamping force. The hardened and ground jaws include prism inserts, allowing secure clamping of round workpieces as well. Details: Heavy-duty steel construction Precision-ground clamping surfaces Hand crank spindle drive Ncedjy Umh Rjpfx Ahzjt Prismatic jaws Very stable and heavy industrial design Ideal for toolmaking, milling, grinding machines, etc. Used, fully functional Normal signs of use (see pictures) Condition: Technically in perfect working condition. Cosmetic wear consistent with age and use, but overall in good condition. Scope of Delivery: Machine vise as shown in the pictures

Condition: like new (used), Heidelberg GTOZ-S52 offset printing machine Ncedpfx Ahoy Umh Dozst The machine is ready to work, very good condition, purchased from small printing house. Technical data: Format: 36x52cm 2 printing units Weight: 3000kg Power supply: 400V Year of production: 1994 Baldwin alcohol dampening Control panel Documentation and additional elements included.

Condition: refurbished (used), Year of construction: 2023, operating hours: 50 h, functionality: fully functional, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, warranty duration: 24 months, pump pressure: 4 bar, power: 30 kW (40.79 HP), OMAX OptiMAX 60X TiltaJET, 30 kW EnduroMAX pump, and TiltaJET for absolutely vertical cuts. Completely overhauled with manufacturer certification and a two-year warranty! The waterjet cutting system from the latest OMAX high-end OptiMAX series, featuring a bridge construction, represents the pinnacle of technological feasibility combined with reliability, durability, and maximum load capacity. Nodpfxjy Umhke Ahzoct Low-noise and low-emission operation combined with simple PC-assisted operation for precision at the touch of a button makes this series ideal for use under the harshest operating conditions in industry and trade, from single-shift operation to 24/7 operation. Features: • Closed measuring system • Digital drives • Brushless servo motors • Precision linear guides, surface-hardened • Portal (bridge) driven on both sides • Maintenance-free IntelliTRAX drive • Energy-efficient ultra-high-pressure EnduroMAX pump • Practical water level regulation as standard • Ergonomic control panel on wheels • IntelliMAX Premium control software • Highly accurate 5-axis TiltaJET kinematics • Accuracy up to ± 0.02 mm • Software and machine components based on the latest OMAX technology With the TiltaJET swivel head, the OMAX system achieves a cutting accuracy of up to ± 0.02 mm. The swivel head automatically compensates for the cutting angle error on the cutting edge, regardless of the selected quality and cutting speed. The configuration of the waterjet cutting system can be freely selected. The system can be expanded with extensive accessories according to your cutting requirements. Please contact us and let us know your configuration requirements. Upon request, financing via leasing is possible at very attractive conditions, e.g., up to 86 months. The machine has been completely overhauled; therefore, the images may differ from the offer. A timely delivery can be arranged with INNOMAX AG.

Condition: used, x-travel 500 mm y-travel 400 mm z-travel 400 mm In our assessment, the machine is in good used condition and can be inspected under power by appointment. Nsdpfxjy Umhdj Ahzjct Accessories, as well as the tools and clamping devices shown in the images, are included in the scope of delivery only if explicitly noted in the additional information. Subject to changes, errors in technical data and specifications, and prior sale!

Condition: used, table dimensions 500 x 1.200 mm number of T-slots 30 distance t-slots 125 mm distance spindlenose to table 110 - 760 mm Swing radius 535 - 1.135 mm boring range 600 mm work height max. 800 mm Ncjdpfx Ajy Umg Tehzst quill stroke 200 mm Height adjustment of the drill head 450 mm no. of turning speeds 18 turning speed range 35 - 1.800 U/min bore capacity in St 60 - in full material Ø40 mm bore capacity in GG 22 - in full material Ø50 mm In our assessment, the machine is in good used condition and can be inspected under power by appointment. Accessories, as well as the tools and clamping devices shown in the images, are included in the scope of delivery only if explicitly noted in the additional information. Subject to changes, errors in technical data and specifications, and prior sale!

Condition: used, Year of construction: 2005, x-axis 450 mm y-axis 300 mm z-axis 300 mm Ncedpfx Ajy Umg Hshzst table dimensions 820 x 400 mm number of tool places 20 Pos. In our estimation, the machine is in good used condition and can be inspected under power by appointment. Accessories, as well as the tools and clamping devices shown in the images, are included in the scope of delivery only if explicitly noted in the additional information. Subject to changes, errors in technical data and specifications, and prior sale!

Condition: reconditioned (used), Title:RHOSS TCHVBZ 2630 – 621 kW Water-Cooled Chiller | Bitzer Screw | Refurbished Headline: Industrial-grade Rhoss water-cooled chiller, fully refurbished and field-tested. Equipped with 2× Bitzer screw compressors, Carel Smart Controller, and energy-efficient R-134a refrigerant — engineered for demanding industrial cooling applications. TECHNICAL SPECIFICATIONS Specification Value Brand / Model RHOSS TCHVBZ 2630 Type Water-Cooled Chiller Condition Refurbished / Tested Cooling Capacity 621.6 kW (534,500 Kcal/h) Refrigerant R-134a Compressors 2 × Bitzer Screw CSH8581-125Y-40P Evaporator Shell & Tube – DN150 Connection Condenser Shell & Tube – DN125 Connection Control System Carel Smart Controller Dimensions (mm) 4070 × 1300 × 1960 Weight 3,297 kg Location Seyhan / Adana, Türkiye TECHNICAL OVERVIEW Industrial-grade Rhoss water-cooled chiller — fully refurbished, field-tested, and verified to meet international performance standards. Equipped with high-efficiency Bitzer screw compressors and a Carel Smart Controller for stable, energy-efficient, and long-term operation. Optimized for demanding industrial applications where reliability and uptime are critical. WHY CHOOSE THIS UNIT Fully refurbished and performance-tested Equipped with high-efficiency Bitzer screw compressors Reliable and durable for continuous industrial operation Energy-efficient R-134a refrigerant Backed by professional after-sales service and spare parts inventory Fast commissioning and on-site technical consultation available ABOUT ÖZSAYIN COOLING SYSTEMS With more than 40 years of experience in industrial refrigeration, Özsayın Cooling Systems provides complete turnkey solutions: Supply of new or refurbished chillers (10 – 2,500 kW) Short- and long-term rental options Ncjdpfxjy Umf No Ahzst On-site installation, commissioning, and maintenance Extensive spare parts inventory for global brands (Carrier, Trane, Daikin, York, Bitzer, Rhoss, Climaveneta, McQuay, etc.) 24/7 technical service and engineering consultancy RENTAL OPTION AVAILABLE This unit is available for short- or long-term rental under flexible terms. Contact us for a customized quotation and technical consultation tailored to your project requirements. CONTACT Mr. Samet Özsayın – Özsayın HVAC Technologies Seyhan / Adana, Türkiye Last Updated: 26.08.2025 HASHTAGS / KEYWORDS #ozsayin #bitzer #rhoss #watercooledchiller #industrialchiller #r134a #coolingsolutions #hvacturkey #chillerrental #refurbishedchiller #screwcompressor #carelcontroller