Hook arm system

Scania R520 V8 6x2/4 / EPSILON CRANE + HOOKLIFT

Condition: new, Year of construction: 2026, Drum chipper series ATH S&F chippers and drum chippers with horizontal infeed are used in many areas of the wood processing industry (sawmills, timber mills). Chippers from the ‘ATH’ series produce high-quality and homogeneous wood chips with a low proportion of fines from residual wood, for example as quality chips for the cellulose industry or as fuel chips for energy generation ATH 220 series - Feed height: 200 mm - Feed width: 500 | 700 | 1000 mm - Number of chipper knives: 2 - 4 pieces - Number of counter knives: 2 pieces - Rotor diameter:520 mm - Number of feed rollers: 3 pieces - Throughput: up to approx. 40 rm/h * - Chipping length: 5 - 50 mm - Chipper drive power: 22 - 110 kW - Drive power feed rollers: 2 x 2.2 kW Bwedpeuz Hmxsfx Aaajk - Operating/control voltage: 400/220 V, 50 Hz - Weight: 2,800 - 4,000 kg ATH 330 series - Feed height: 300 mm - Feed width: 500 | 700 | 1000 mm - Number of chipper knives: 2 - 6 pieces - Number of counter knives: 2 pieces - Rotor diameter: 700 mm - Number of feed rollers: 3 pieces - Throughput capacity: up to approx. 70 rm/h * - Chipping length: 5 - 80 mm - Chipper drive power: 37 - 250 kW - Drive power feed rollers: 2 x 3.0 kW - Operating/control voltage: 400/220 V, 50 Hz - Weight: 3,500 - 5,000 kg *depending on chipper length, kW main motor, number of knives, feed Advantages: - Maximum throughput - Low fines content - Low maintenance - Flexible use - Customised production

Condition: new, power: 90 kW (122.37 HP), Year of construction: 2026, A double rotor hammer crusher is a type of crusher in which two rotors are mounted on a single shaft, combined to form a spinning rotor. The double rotor arrangement enhances the crushing capabilities and provides a more efficient and reliable crusher design compared to single rotor crushers. Here are some key features and aspects of a double rotor hammer crusher: 1. Two Rotors: As the name suggests, the crusher has two rotors that rotate in opposite directions on a common shaft. This dual rotor configuration allows for increased impact and crushing power. 2. High Capacity: The dual rotor design enables the crusher to handle larger feed sizes and higher capacity compared to single rotor crushers. It is suitable for crushing materials with high hardness and large sizes. 3. Versatility: Double rotor hammer crushers are versatile and can be used in various applications, including the reduction of limestone, gypsum, coal, and other similar materials in the mining, cement, and building materials industries. 4. Impact Crushing: The primary mechanism of crushing in a double rotor hammer crusher is through the impact of the hammers against the material. The material is fed into the crusher, and the high-speed rotating hammers impact and shatter the particles. 5. Adjustable Gap Settings: These crushers often have adjustable gap settings between the rotors and the impact bars, allowing control over the final particle size. 6. Durability: The robust design of the double rotor hammer crusher makes it durable and capable of handling tough materials and continuous operation. 7. Reduced Wear: The dual rotor arrangement can help distribute wear more evenly across the hammers and other wear parts, potentially extending the overall lifespan of the crusher. Bwodpfsq Nf Enjx Aaaok Typical Technical Specifications While exact numbers vary by manufacturer, these are the standard ranges for industrial models: Model (Rotor Size),Max Feed Size,Output Size,Capacity (t/h),Total Motor Power 600 × 400,≤110 mm,≤3 mm,10 – 15,18.5+18.5 kW 800 × 600,≤120 mm,≤3 mm,40 – 50,45+45 kW 800 × 800,≤180 mm,≤3 mm,50 – 60,45+55 kW 1000 × 800,≤180 mm,≤3 mm,70 – 80,75+55 kW 1100 × 1000,≤200 mm,≤3 mm,70 – 100,90+110 kW 1400 × 1200,≤200 mm,≤3 mm,90 – 110,132+160 kW For more details about double stage hammer crusher, or double rotor crusher, welcome to leave us a message, our team will get back to you at the earlist.

Condition: good (used), functionality: fully functional, 2 Pcs. “Steinert NES 200 220 E 5009” for Sale Manufacturer: Steinert Type: NES 200 220 E 5009 Belt widthness: 2.000 mm (New belt) With new control-unit. Overhauled, balanced, sandblasted and painted. Bwodpexb Tbzofx Aaaek

Condition: new, power: 11 kW (14.96 HP), fuel type: electric, color: other, Year of construction: 2023, Drive: Track Empty weight: 1.420 kg Bsdpfxjx A R Hqe Aaajwk Make of engine: Internal Permanent Magnets Track width: 18 cm Output of the auxiliary hydraulics: 28 l/min Transport dimensions (LxWxH): 2,505x1,05x2,3 Rental currency: EUR Please contact KEY-TEC Sales for more information

Condition: new, axle configuration: 3 axles, Year of construction: 2025, GVN Trailer 3 Axle Exclusive Lowbed Bjdpfx Aaoqxbcnjajwk    Please get contact with us for more informaiton;  

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Bsdpfx Aevf E Avjaaowk Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: new, Year of construction: 2023, machine/vehicle number: 7YXXX, VIS G is the ideal and the most efficent solution for serap processing like stampings, trimmings, wires mostly recommended for the automotive industry, metal recyclers and non-ferrous metal remelting industry. Bwodemqi Akopfx Aaask

Condition: like new (used), Year of construction: 2024, Permanent overbelt magnet separator TYPE DMPM800 1,400 x 900 x 220mm Bsdpshun Uiofx Aaajwk ===== Solid steel construction, welded Construction welded & painted RAL 7016 (anthracite gray) Magnet dimensions: 800x500x180mm Drive roller + deflection roller S235 steel welded and machined Ø220x700mm crowned, shaft fixed with clamping bearings. Drive: GEMOTEG 1.1KW slip-on gear motor, speed 0.4-0.6m/sec Connection 400V, 50Hz, protection class IP54 Drive ready for connection to motor terminal box (commissioning must be carried out by a qualified electrician) PU conveyor belt DM 20/2 0+010 PU black matt 5.4mm thick Conveyor belt width: 650mm 7 TG-40 studs high frequency welded Belt material: 3-layer, particularly transversely stable * equipped with rust-proof alligator connectors RS125 Magnet properties: Built-in magnetic core: Strontium Ferrite Y30 Bound SfRe strontium hard ferrite magnetic core encased in soft iron so that very high permeability can be guaranteed. Housing with 1.4301 stainless steel plate and pole shoes tightly closed and sealed. Conveyor belt, conveyor belt system, discharge belts, belt conveyor, magnetic separator, overbelt magnetic separator, recycling, wood chips, plastic, metal-free metal detection, neodymium, overbelt magnet, magnetic belt separator Our core competence lies in supplying the customer with exactly what he really needs. Together with our customers, we work out customer-specific, individual solutions and supply corresponding systems from our own production. Feel free to contact us by phone to find a suitable solution for your application.

Year of construction: 2026, condition: new, Oscillating screen ASM series S&F oscillating screens and horizontal screens are used in many areas of the wood processing industry (sawmills, pelleting plants). Screening machines of the "ASM" series screen wood chips, wood pellets, sawdust and sawdust, waste wood, biomass and many other sawmill by-products in dry and wet applications. The material-protecting, horizontal-circular screening movement of the inclined screen box ensures a high separation efficiency of the vibrating screen. One advantage of the screening machine is that long and fibrous particles glide diagonally to tangentially over the screening surface. This means that - in contrast to throw screens - no jamming or plugging grain occurs. Further advantages are the robust design, the high screening capacity and the long, low-maintenance running time of the screening machine. In addition to standard dimensions, the company also supplies the "ASM" series as a "customising solution" in a split design for existing plants. This makes it possible to use new screening machines in cramped and difficult-to-access spaces in existing plants or sawmills. Screening machines of the "ASM" series offer screen sizes from 0.5 to 15 m² (per screen deck) and are characterised by a high screening capacity (up to 350 m³/h - depending on the material). At a glance: - Ideal for: Wood chips, pellets, sawdust, biomass, bark, waste wood, substitute fuel. - Areas of application: Wood industry, recycling and waste disposal, animal feed - Screening area: 0.5 - 15 m² (30 m² as double deck) - Screening capacity (depending on material): up to 350 m³/h - Separation size: 0.1 - 150 mm (depending on size) Bwjdpfein Ey Sex Aaaek - Drive power: 0.55 - 15.0 kW (depending on size) Advantages: - High screening capacity - High separation efficiency - No jamming and plugging - Low noise and low maintenance - Flexible use - Individual production Do you need further information? Please contact us! We will be happy to advise you.

Year of construction: 2025, condition: new, Description: Screening deck system consisting of 1 decks for screening waste wood or wood chips. Bedpfxsg I Uqfj Aaaowk input material 0-200 mm capacity approx. 80 m³/h (depending on material) material is separated into 2 fractions 0-25 mm and oversized material to be mounted on customer's own baffle walls or underframe Technical data: Screen deck 1: length = 5,200 mm; width = 1,215 mm o Outer dimensions: length = 5.500 mm width = 1.850mm o Screen surface 6,3 m², number of shafts 40 pieces o Drive 2 x 7,5 kW gear motors o Screen body polyurethane (star screen) D 166 / 12 fingers o Screen shafts as plug-in system (adaptation to other grain sizes easily and cost-efficiently possible) o Lubrication of the bearings to the outside, optional central lubrication against surcharge possible