Hydr. scissor lift table

TREPEL - L. A. VAN EIJLE & Co.

Year of construction: 1990, condition: repair required (used), Mobile jaw crushing system, operating hours approx. 10.000, engine Caterpillar 6 cylinders with generator set approx. 35 KVA, year of construction approx. 1990, jaw crusher KUE-KEN (KK114 inlet 1140 x 750 mm) incl. magnetic tape (iron separator), total weight 48 tons on semi-trailer chassis. Nsdpfx Ahehz Dmgo Uodf Condition: Motor and conveyor systems run perfectly, only the drive shaft of the crusher is defective (damage approx. € 17.000)

Condition: excellent (used), We offer for sale the following Gránit-Mill 90 wood pelletizing presses, in the condition shown in the pictures, after the pelletizing plant has ceased operation. The machine is made in Hungary, our company has an excellent relationship with the manufacturer, and we can help you purchase parts. Drive and sticker handling is similar to the old CPM machines. The presses (with pine) are capable of 1.2-1.5 t/h/pc. Ndjdpfxop T Twuo Ah Uof Price: €29 900/press €49 900/ 2 presses Included in the price: pre-tank control cabinet dosing screw permanent magnet conditioner press motors pre-tank 1.1 kW feeder 1.5 kW conditioner 15 kW tablecloth 0.55 kW main engine 90 kW 3 stickers all three are made by La Meccanica barely used It has a 6 x 45 mm hole for pine 2 sets (total of 4) notched collars spare parts screws nuts breaker pin assembly aids Status: Engines and drives intact. Both machines tested. It is recommended to replace the neck bearing of the right machine. Smaller parts (such as the pellet cutter) must be replaced. There is no water supply, the place is prepared. The greasing method is manual, but central greasing can be easily installed. Summary: The machine on the left can be put into production immediately. It requires a minor service on the right side. If necessary, the machine can be tested at a pre-arranged time. Not in production, must be prepared. It is possible to check the mechanical durability and volume density of the produced pellets on site!

Condition: new, Year of construction: 2025, machine/vehicle number: 180965471, Additional options and accessories Notes Mobile impact crusher on crawler track The K1 impact crusher with tracked undercarriage, the new addition to the product range with impact mill with a capacity of 250 t/h . Can be equipped with closed circuit re-screening to perfectly calibrate the final product. It is appreciated for the excellent quality of the crushed product and also gives its best in terms of operating economy. Production capacity: approx. 250 TO/H Proportional distributor with \"Load Sensing \" for optimization of the system and reduction of fuel consumption by approx. 30%. gap hydraulically adjustable even during the crushing operation fast blocking system with wedges and folding cylinders dust extraction system tank pump magnetic separator warranty 1 year up to max. operating hours from start of operation of the plant Technical data: Impact crusher type M x 700 mm Crushing gap from 30 (20) to 100 mm (gap adjustment to 20mm only possible with 3rd grinding track) Feed hopper 4 m³ - 1800 x 3700 mm Grizzly feeder 900 x 3400 mm Main conveyor belt 800 x 9600 mm 4 cylinder diesel engine with constant speed 82 HP/60 KW , exhaust gas stage V Ndodpfxehd Naio Ah Uof Control panel chain drive 400 x 2900 mm Weight: kg Transport length 12560 mm Transport width:2550 mm Transport height 3200 mm More information Purpose: construction, General condition: very good, Technical condition: very good, Visual condition: very good,

Year of construction: 2017, condition: excellent (used), Bluhm weber legi-air 4050 labeling machine More pieces in stock! year built: 2016-19 Print resolution 8 dots/mm (203 dpi) 12 dots/mm (300 dpi) 24 dots/mm (600 dpi) Print speed Up to 400 mm per second Tamp sizes (mm) Tamp-Blow standard of 12.5 x 7 to 160 x 300 mm, Nodpfxsfp A I Ee Ah Usdf label lengths must be limited in accordance with label quality, longer or smaller labels are possible using special tamps Label gap Minimum 3 mm Label roll 300 mm diameter, up to 450 running meters, core 76 mm (3"), outside winding (optional inside winding) Data interfaces RS232, RS422, RS485, Ethernet Optional: Profibus Dimensions (L x H x W) 770 x 560 x 580 mm, Applies to system with 250 mm stroke Display controller Multi-language operator guidance 5.7" VGA touch display Service interval indicator Polling, editing and saving of label data USB connection for memory medium or keyboard Compressed air connection 6 bar, the compressed air must be clean, dry and oil-free

Condition: good (used), Glass laminating system Type: Vacuum glass laminating system HVD-G02 Vacuum glass laminating system Glass laminating system, with 2 heating devices TOOL TEMP Model type TT-138B, S/N 310-1877-1, 310-1877-2 Laminating area approx. 2,900 x 1,400 mm, with feed table, stainless steel Control cabinet, area approx. 2,600 x 1,250 mm Control tower PC, 17" LCD monitor ACER Model/type AL711, mouse, keyboard The system consists of the following main components: Vacuum chamber (chamber + lid) Pneumatic lid drive Transport roller conveyor Lifting device Heating plates Chamber frame Vacuum technology (pumping station, valves, lines, feedthroughs, measuring technology, etc.) Pressure water temperature control device (2 piece) Transport pallet Lifting frame Control with control panel Technical data: Ndedpjdkp D Hofx Ah Uof Step-by-step pumping via valves adjustable up to 0.01 mbar; Heating / cooling: time adjustable via control Heating temperature directly adjustable on the pressurized water temperature control device (max. 140

Year of construction: 2020, condition: new, Oxygen and temperature measurement in molten metals Ndsdegqr A Dopfx Ah Ujf

Year of construction: 2023, condition: new, Chopping height max. mm. 200 Infeed width mm. 500 Infeed rollers piece 3 Rotor flight circle mm. 600 Chopping length approx. mm. 20-30 output - output 16 - 20 rm/h chipping Chipper blade piece 2 Feed motors kW 2x2,2 Weight approx. net kg 4100 Inlet : horizontal machine base : steel, inert gas welded Rotor : steel, inert gas welded, dyn. balanced. Bearing : Oversized roller bearings. Bearing housing : Steel, flanged housing. Feed rollers : steel, special toothed. Chip outlet : underneath the machine. Machine grate : (sieve) for secondary crushing of excess lengths. Drive pulley : Matched to main motor N=1500 min-1 Hydraulic system : consisting of: Hydraulic pump, diaphragm accumulator, cylinder, pressure gauge, control valves for lifting of the upper feed roller. Ndodpfxjncd Azj Ah Uef Feeding : by 2 gear motors, Make NORD GEAR

Condition: like new (used), Manufacturer: V. Randwijks Ndjdpfx Aog Snt Sjh Uef Rotor Dia.: 500mm Rotor Width: 700mm Electrical Motor: 22kW / 1.470 RPM

Condition: used, Year of construction: 2023, load capacity: 5,000 kg, lifting height: 3,770 mm, total length: 5,930 mm, Diesel forklift Linde H 50D-01/600 Ndedpexd El Rofx Ah Usf Drive Diesel Year built 2023 Lifting height (mm) 3,770 Lifting weight (kg) 5,000

Condition: new, functionality: fully functional, power: 18.5 kW (25.15 HP), gearing type: hydrostat, fuel type: diesel, fuel tank capacity: 50 l, color: red, overall weight: 2,600 kg, empty load weight: 2,500 kg, lifting power: 1,000 kg/m, lifting height: 3,310 mm, tire condition: 100 %, axle configuration: 2 axles, number of seats: 1, shovel volume: 0.4 m³, digging bucket width: 160 mm, Year of construction: 2025, load capacity: 980 kg, Equipment: additional headlights, adjustable boom, all wheel drive, cabin, differential lock, head guard, hydraulics, pallet forks, standard shovel, trailer coupling, The H&R 2210-T telehandler with the new 3-cylinder Perkins Turbo engine (Mannheim, Germany) meets the Euro 5 standard even without a particulate filter. The new turbo engine is particularly economical, and with the 2-stage hydrostatic drive, it can reach speeds of approximately 16 km/h. Thanks to the large steering angle of 42° and a small turning circle, it is ideal for use on even the smallest areas. The 2210T wheel loader with telehandler comes standard with a quick-change pallet fork and a standard bucket, so you can start working immediately. With the additional hydraulic control circuit, various attachments can be used for the yard loader. The telescopic boom gives the 2210-T an excellent reach. The electric gear on the joystick makes operating the H&R 2210T particularly convenient. H&R loaders are technically and visually optimized in-house and thoroughly tested. In addition, each machine receives extensive rust protection treatment. Our loaders are CE-compliant according to the EU Machinery Directive. Our machine has a TÜV Süd certificate for obtaining an individual operating permit in accordance with Section 21 of the German Road Traffic Licensing Regulations (StVZO) (road approval/operating permit as a self-propelled work machine). Advantages of the H&R 2210T Telehandler • Fully equipped • Efficient engine from Germany (Euro 5) • Extensively optimized in-house • Extendable telescopic boom • Heated comfort cab • Includes pallet forks • Includes standard 150 cm bucket • Joystick with float position and electric gear • Auxiliary hydraulics for front-mounted tools Nedpfeul Af Djx Ah Uedf • Hydraulic oil cooler • Brake-inch pedal • Rearview camera with display • Rotating beacon • LED work lights front and rear • Wide tires 31 x 15.5-15 • Radio with MP3 and USB • Adjustable steering column and seat • Hour meter and fuel gauge • Trailer coupling • 1-year spare parts warranty • CE compliant according to the EU Machinery Directive Price Net: €24,975.00 VAT: €4,745.25 Gross: €29,720.25 Financing available! Optional 2-year warranty €590 TÜV road approval / operating permit for work machine €595 Transport to Germany and Austria upon request Technical specifications Engine: 3-cylinder Perkins Turbo Power: 25 HP Emissions class: Euro 5 Lifting capacity: 980 kg Lifting height: 3310 mm (bottom edge of standard pallet fork) Unloading height: 2796 mm (bottom edge of standard bucket tipped out) Lift time / lowering time: 4.0 / 3.5 seconds Wheelbase: 1.6 m Dimensions (L x W x H): 3710 x 1496 x 2340 mm Weight: 2430 kg Tires: 31 x 15.5 - 15 Accessories and spare parts are available from us. Please provide us with your telephone number when making inquiries!