Narrow-aisle truck

Aisle-Master 20NE

Condition: new, functionality: fully functional, Year of construction: 2024, load capacity: 2,000 kg, lifting height: 7,200 mm, fuel type: electric, mast type: triplex, fork length: 1,150 mm, fuel: electricity, Brand: Aisle-Master Type: 20NE Capacity: 2,000 kg Year of construction: 2024 Pjdet Dwlcepfx Adlogk Lifting mast: Triplex Lifting height: 7200 mm

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Pedpfowp Rqfox Adlsgk Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: new, functionality: fully functional, Year of construction: 2024, load capacity: 2,000 kg, lifting height: 7,200 mm, fuel type: electric, mast type: triplex, fork length: 1,150 mm, color: yellow, fuel: electricity, Brand: Aisle-Master Type: 20NE Psdpfxjt Hff As Adlsgk Capacity: 2,000 kg Year of construction: 2024 Lifting mast: Triplex Lifting height: 7200 mm

Condition: as good as new (ex-display), functionality: fully functional, Year of construction: 2023, operating hours: 37 h, load capacity: 2,000 kg, lifting height: 7,200 mm, fuel type: electric, mast type: triplex, fork length: 1,150 mm, color: yellow, fuel: electricity, Brand: Aisle-Master Type: 20NE Capacity: 2,000 kg Pgsdpfjt Hfg Hsx Adlsk Year of construction: 2024 Lifting mast: Triplex Lifting height: 7200 mm

Condition: new, Comparable to Behringer, Kaltenbach, Kasto, Jaespa, etc. Cutting range 90° Round: 260 mm Flat: 300 x 260 mm Smallest diameter: 5 mm NC-controlled, automatic material feed with hydraulic full-stroke material clamping Easy operation via NC control with plain text display Material advance function without reclamping for short section cuts Robust, linear-guided feed gripper with servo positioning for maximum precision Automatic adjustment of blade guides to material width Psdpfx Adsh Tnd Aologk Recommended options: Powered chip brush synchronized with blade speed Separate control panel 7" CE panel, network-compatible, up to 1000 data sets storable, history memory for various functions and data, etc.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2021, operating hours: 1,500 h, load capacity: 2,000 kg, lifting height: 6,350 mm, free lift: 2,115 mm, load center: 600 mm, fuel type: electric, mast type: triplex, construction height: 3,015 mm, battery capacity: 930 Ah, battery voltage: 48 V, fork length: 1,070 mm, tire condition: 90 %, Equipment: CE marking, front guard, full service history, pallet forks, sideshift, Machine in good condition, only used indoors on level surfaces, carefully handled (3 permanent warehouse staff—no temporary workers). Selling due to relocation to a high-bay warehouse. Pgjdsw Nqhiepfx Adlsk

Condition: used, Year of construction: 2016, Technical details: Pgodsudf Evepfx Adlek weight: 22 t

Condition: excellent (used), Year of construction: 2012, The Vertical Machining Center enables drilling, milling and cutting operations and cornering within the scope of technical capabilities indicated in the manual in details: plastic, PVC, ABS, methacrylic, polycarbonate, thermoplastic, composite, aluminum. The vertical work table allows for easy feeding and unloading of processed details and reducing the maximum size of the device to the minimum necessary. Tool change with the use of a 10-element magazine located on the side of the device, it enables various works to be carried out without the need to remove the workpiece from the table. Maximum dimensions of the processed detail: X= 4200mm Y= 1600mm Z= 20mm Rapid traverse speed (m/min): X=30 Pgjdpfx Adomzbr Seljk Y=30 Z=15 Set of milling heads T1 and T2: Spindle power (kW) - 3.3 Rotation speed (rpm) - max 18000 Electric spindle with clamp - ER32 T3 Drill Head Assembly: Spindle motor power (W) - 370 Rotation speed (rpm) - max 2800

Condition: used, Year of construction: 2015, Vertical CNC machining center with 3 controlled axes and exceptional Y-axis machining capacity. It is equipped with a vacuum table clamping system that holds plates and sheets with the help of vacuum. This solution is particularly effective when machining thin parts that are difficult to fix using conventional clamping systems. The machining center is equipped with a set of valves that allow you to turn on or off different table zones, thus concentrating the vacuum in a specific area and optimizing the clamping of small components. Possibility of performing interpolated milling and drilling in composite panels, aluminum, steel or titanium sheets and aluminum profiles. Tekna provides user-friendly software that can be operated by both experienced CNC programmers and less experienced users. The TKE 783 is a machining center with 3 controlled axes for interpolated drilling and milling in composite panels, aluminum, steel or titanium sheets and aluminum profiles. Technical specifications: Model: Tekna TKE783 Year of manufacture: 2015 Power: 29 kW Dimensions of the machining table: 2010 x 6300 mm Weight: 4842 kg Speed: X axis 70 m/min; Y axis 55 m/min; Z axis 30 m/min Software: Windows, Embedded, Teach-in software CAD/CAM 2D NC TOOL Made in: Italy Other: aluminum milling up to 4 mm was worked on. The machine is connected, you can see how it works and test it in Estonia. It will be ready for transportation in April-May. Pjdpsv D A Imjfx Adlogk If you have any additional questions, we will be happy to answer them.

Condition: as good as new (ex-display), Year of construction: 2025, Pressing area: 3000 mm x 1500 mm Operating vacuum: -0.85 bar Vacuum pump flow rate: 40 m³/h Pump power: 1.5 kW Noise level: 70 Db Heating temperature: max. 200 °C Podpfxju Egp Is Adlsgk Heating power: 16 kW Machine length: 3100 mm Machine width: 1650 mm Machine height: 1750 mm Weight: 950 kg