Screening machine

ASCO SD Compact + BC + DEC

Condition: ready for operation (used), Year of construction: 2003, functionality: fully functional, The unit was dismantled from the production line and operated until the end. Regularly serviced, ready for operation. Ijdoya Uubopfx Am Deih

Condition: new, Year of construction: 2024, Gold River SWZ-700 water separators Application description: The GOLD RIVER SWZ series separator has been designed for special tasks, it can cope with the most difficult materials that contain many properties that disturb the separation process in separators commonly available on the market. SWZ water separators separate heavy fractions (non-ferrous metals) from, among others, plastics in the process of recycling secondary raw materials. SWZ separator equipped with a four-section copper water system equipped with radial nozzles with variable linear geometry. The separator uses the latest divided type of separation mat. The development of a modern module for preliminary division and preparation of material guarantees the purity of recovered raw materials in a very short time (plastics, metals). Why a water system? Our device uses a system similar to that used in the gold recovery industry. We use water as a carrier and a force that affects the materials in a gentle way. In the water system, all particles with higher mass are gently washed out and separated, generating no losses during the entire separation process. The properties of water together with our proprietary solutions are unrivaled compared to, for example, air separators. SWZ type separators are used: Separation of heavy from light materials (metal granulates contaminated with plastic, foil, paper, cotton, fibers) Cleaning plastics after air separators (dry) Separation of metals in cable and non-ferrous metal recycling lines The SWZ-700 water separator, thanks to the use of the latest module, performs the separation process in a very short time, therefore it is characterized by a high hourly efficiency of separated material of approximately 1200 kg/h. Description of action: The material fed into the separator goes through the transport channel to the module for initial fraction division into its mass and humidity changes. Some of the material is separated at this stage. In the second part of the module, the humidity of the remaining batch changes. Then the material falls onto the separation table where the final fraction separation takes place. As a result of this process, we obtain valuable materials from both sides of the separator. Iedpfx Aeua Tbwem Doih Construction description: The massive structure and the inertial drive of the separator are made of materials appropriately selected to withstand the overloads resulting from vibrations. The supporting frame ensures excellent stiffness and failure-free operation for many years. Due to the type of vibration drive, the design does not require the installation of a soil separator. Separation table equipped with hydraulic adjustment of the angle of inclination. The separation table has a special module for initial division of fractions into their mass and preparation for final separation. The water system has several water pressure valves. The water circulation in the separator is closed. There is no need for constant access to an external water source because the device works using the water already in the tanks. Based on experience and continuous research in our laboratories. We are able to provide you with separators individually adapted to the specific nature of the material being separated. In various versions and sizes. SWZ-700 separators are manufactured to individual order.

Year of construction: 2026, condition: new, Oscillating screen ASM series S&F oscillating screens and horizontal screens are used in many areas of the wood processing industry (sawmills, pelleting plants). Screening machines of the "ASM" series screen wood chips, wood pellets, sawdust and sawdust, waste wood, biomass and many other sawmill by-products in dry and wet applications. The material-protecting, horizontal-circular screening movement of the inclined screen box ensures a high separation efficiency of the vibrating screen. One advantage of the screening machine is that long and fibrous particles glide diagonally to tangentially over the screening surface. This means that - in contrast to throw screens - no jamming or plugging grain occurs. Further advantages are the robust design, the high screening capacity and the long, low-maintenance running time of the screening machine. In addition to standard dimensions, the company also supplies the "ASM" series as a "customising solution" in a split design for existing plants. This makes it possible to use new screening machines in cramped and difficult-to-access spaces in existing plants or sawmills. Screening machines of the "ASM" series offer screen sizes from 0.5 to 15 m² (per screen deck) and are characterised by a high screening capacity (up to 350 m³/h - depending on the material). Iiedpfx Aein Ey Sem Djh At a glance: - Ideal for: Wood chips, pellets, sawdust, biomass, bark, waste wood, substitute fuel. - Areas of application: Wood industry, recycling and waste disposal, animal feed - Screening area: 0.5 - 15 m² (30 m² as double deck) - Screening capacity (depending on material): up to 350 m³/h - Separation size: 0.1 - 150 mm (depending on size) - Drive power: 0.55 - 15.0 kW (depending on size) Advantages: - High screening capacity - High separation efficiency - No jamming and plugging - Low noise and low maintenance - Flexible use - Individual production Do you need further information? Please contact us! We will be happy to advise you.

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 61036946, clamping force: 800 kN, screw diameter: 40 mm, displacement volume: 201 cm³, injection pressure: 1,860 bar, injection weight: 183 g, mold height (min.): 150 mm, ejector force: 22,000 N, ejector stroke: 100 mm, opening stroke: 750 mm, installation height: 400 mm, total length: 4,750 mm, total width: 1,670 mm, total height: 1,850 mm, overall weight: 5,600 kg, heating capacity: 11.5 kW (15.64 HP), drive type: Vollelektrisch, clear span: 735 mm, tool weight: 600,000 g, Injection molding machines direct from the manufacturer! As the manufacturer KraussMaffei, we offer you our tested and flexible stock machines here: The basic injection molding machine, precisionMolding, offers the perfect entry-level solution for all-electric injection molding, enabling you to react quickly and innovatively to market requirements. It combines high performance, simple operation and short delivery times. It can be used in a wide range of applications, e.g. in the packaging industry, the electrical and electronics industry, medical technology and the automotive industry. Your benefits: - Optimized price-performance ratio for a wide range of applications - High energy efficiency thanks to all-electric machine concept - Realization of demanding delivery times thanks to basic machine concept with a wide range of options TECHNICAL DATA: KM 80 / 380 PA G01 (order 38670023) Iiodpeud H Dmofx Am Dsh CONTROL  MC P1 with 15" TFT color screen with multi-touch functions CLAMPING UNIT  Clamping force kN 800  Mold opening force, max kN 120  Clear width (h x v) mm 470 x 420  Clamping platen (h x v) mm 610 x 560  Tool installation height min. - max. mm 150 - 400  Opening width mm 750  Mold opening stroke max. mm 350  Ejector drive electric  Ejector stroke mm 100  Ejector force forwards/backwards kN 22 / 22  Ejector speed forwards/backwards mm/s 300 / 300  Max. Mold weight kg 600 SPRING UNIT  Screw diameter / type mm 40 / standard  Effective Ls/D ratio 20.0  Injection pressure bar 1860  Stroke volume cm³ 201  Shot weight at max. stroke for PS g 183  Injection speed mm/s 200  Injection flow rate cm³/s 251  Screw drive/speed 1/min 334  Plasticizing flow (standard) g/s 24.7  Nozzle contact force kN 34 ELECTRICAL PARAMETERS  Connected load kW 20.6  Installed heat output kW 11.5  Power supply V / Hz 400 / 50 3 phases with neutral conductor WEIGHT AND DIMENSIONS  Net weight with switch cabinet t 5.6  Length x width x height m 4.75 x 1.67 x 1.85 ADDITIONAL EQUIPMENT  Low-wear plasticizing  BluePower fully insulated plasticizing cylinder  Open nozzle  Air valve 1 - fold (BWAP)  Pneum. Control hot runner valve gate 1 - compartment  Electrical interface cascade 4-fold  Euromap interface handling E18, E63  Euromap interface (central computer) E67, E77  Water battery 4 - compartment  Automatic central lubrication  Adaptive Process Control (APC)  Spray embossing circuit  Graphic analysis package The machine is located in our factory in Parsdorf and is available at short notice. Further additional options can be offered on request. We look forward to your inquiry.

Condition: like new (used), functionality: fully functional, mileage: 70,000 km, first registration: 05/2019, color: grey, fuel: diesel, fuel type: diesel, emission class: euro6, Year of construction: 2019, Volkswagen T-ROC IQ Drive Year: 05/2019 Iisdpsymf Avjfx Am Djh Color: Metallic Grey Fuel: Diesel Engine: 1.6 TDI Output: 85 kW (116 hp) 6-speed manual gearbox + reverse Seating capacity: 5 Emissions Standard: Euro 6 ABS Adaptive cruise control Removable towbar Bluetooth CD player Radio Lane Assist On-board computer Navigation system Rear parking sensors Front-wheel drive Multifunction leather steering wheel Electric windows Electric mirrors Air conditioning Airbags Power steering Brake Assist Central locking Electronic differential lock (EDL) Tyres: 215/55 R17 Mileage: 70,000 km

Year of construction: 2021, operating hours: 1 h, condition: as good as new (ex-display), functionality: fully functional, power: 5.5 kW (7.48 HP), overall weight: 1,500 kg, total length: 3,340 mm, total width: 2,360 mm, total height: 2,925 mm, input voltage: 400 V, Equipment: documentation/manual, emergency stop, type plate available, Applications & Customer Benefits: The ASCO SD Compact is a semi-mobile screening machine for efficient processing of soil, gravel, wood chips, waste, and recycling materials. It delivers high-precision separation, flexible operation, and reliable performance for construction sites, recycling plants, and material processing facilities. Key Features: • Modular design with interchangeable drums & quick-change system • Adjustable screen inclination & variable drum speed (5–20 rpm) • Up to four fractions per drum segment with cleaning brush system • Optional bunker expansion for +50% input capacity • Compact, semi-mobile design with easy transport & setup Iedpfsw Ryl Hex Am Djih Tech Highlights: Drum Ø 1.3 m · L 2.1 m · Mesh Ø6–Ø100 mm · Qmax 20–50 t/h · n 5–20 rpm · P 5.5–7.5 kW · Weight 1500 kg · Screening surface 7 m²

Year of construction: 2023, condition: new, Rental system Hosokawa Alpine AS 200 Baseline. TECHNICAL DATA Chamber diameter 200 mm Gas pressure range 2 – 8 bar (g) Fineness range d50 1 – 40 μm Bn83a7ch Nominal gas flow 150 – 200 Nm³/h Dimensions (l/w/h) (without aspirator) 1.2 x 0.8 x 1.3 m Power supply 230 V; 2.2 kW REFERENCE PRODUCTS Product / End fineness / Throughput Celecoxib 90% ᐸ 23 μm 33 kg/h Nifedipine 90% ᐸ 2.4 μm 8 kg/h Iiedpfx Amjm Nbnre Djh Progesterone 90% ᐸ 9 μm 20 kg/h Diosmin 90% ᐸ 4 μm 8 kg/h Omeprazole 99% ᐸ 5 μm 3 kg/h Cosmetic powder 90% ᐸ 10 μm 15 kg/h A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant We are also interested in buying back disused HOSOKAWA ALPINE machinery

Condition: new, power: 55 kW (74.78 HP), Year of construction: 2026, A hammer crusher is a machine that uses high-speed rotating hammers to crush and break materials into smaller pieces. It is commonly used in various industries, including mining, cement, construction, metallurgy, and chemical processing. The basic principle of a hammer crusher involves a central rotor with hammers or blades that rotate and impact the material being crushed against a hard surface. Here are the key features and components of a typical hammer crusher: 1. Rotor: - The rotor is a central component of the hammer crusher. It usually consists of a shaft with multiple discs or hammers attached. - The rotor's rotation causes the hammers to swing outward, impacting the material. 2. Hammers: - Hammers are the striking or crushing elements attached to the rotor. They can be fixed or pivotally attached. - The material is crushed as the hammers impact it, generating kinetic energy. 3. Casing or Housing: - The casing or housing encloses the rotor and hammers, providing structural support and safety. - It also serves to contain the crushed material and direct it to the desired discharge point. 4. Grate Bars or Screens: - Positioned at the bottom of the crusher casing, grate bars or screens control the size of the crushed material by allowing smaller particles to pass through while keeping larger ones inside for further crushing. 5. Impact Plate: - Located near the bottom of the crusher, the impact plate absorbs the impact energy generated by the hammers and prevents excessive wear on the casing. Isdpfxeq I Nxde Am Djih 6. Drive System: - The hammer crusher is powered by a motor connected to the rotor through a drive belt or coupling. - The motor provides the necessary power to rotate the rotor, enabling the hammers to crush the material. 7. Adjustable Discharge: - Some hammer crushers feature an adjustable discharge, allowing users to control the size of the crushed material by adjusting the gap between the impact plate and the hammers. 8. Applications: - Hammer crushers are used for crushing a variety of materials, including coal, limestone, gypsum, aggregates, and various minerals. - They are commonly employed in the mining industry for primary and secondary crushing of ore. - In the cement industry, hammer crushers are used to crush limestone and other materials before they are mixed into the raw meal. 9. Maintenance and Safety: - Regular maintenance is essential to ensure the efficient operation of a hammer crusher. This includes checking and replacing worn hammers, inspecting the rotor, and lubricating moving parts. - Safety features, such as access doors and safety guards, are typically incorporated to prevent accidents during operation and maintenance. Technical Specifications (Typical MINGYUAN Series) Model Category,Max Feed Size,Capacity (t/h),Motor Power (kW),Rotor Speed (rpm) Small (PC-400), ≤100mm, 5 – 10, 11, "1,000" Medium (PC-800),≤200mm, 20 – 50, 55, 750 – 900 Heavy (PC-1200),≤350mm, 80 – 110, 132 – 160, 600 – 750 Heavy Hammer,"≤1,200mm", "500 – 1,000+ ","400 – 1,000" ,Variable

Condition: ready for operation (used), Year of construction: 2019, operating hours: 15 h, machine/vehicle number: MP.DBDO-00198, Size 75 x 106 cm, non-stop function in feeder and delivery, integrated fine adjustment of the cutting plate, motorized die-cutting pressure adjustment, simple operating concept. The basic model is already equipped with all functions and equipment required to start production. Short makeready times, high flexibility thanks to an extended range of materials, accommodates smaller die-cutting tools. Machine number: MP.DBDO-00198, Impressions: 15 million. Iodpfx Amjyhn Uqs Deih

Condition: refurbished (used), Wood chip screen IDL000756 - Three layers Ijdpfx Aetmtf Rem Deih - Manufacturer: Passimo OY - Screen area: 15 m2 - After renovation.