Overhead crane ± 10.500 mm x 12.500 kg

Demag ZKKE

Condition: like new (used), Year of construction: 2010, machine/vehicle number: 1099883, operating hours: 100 h, Demag end carriage pair End carriage DRS315 Hoist unit EZ DR20 Trolley gauge 2240 mm Reeving 4/1 The crane shows virtually no wear, very little use in a machine construction factory. Dismantled in July 25 and stored dry. Fedew H S Avjpfx Abuepc Complete with documentation and HBC Spectrum radio remote control. All motions with frequency inverter! Modifications can be offered separately.

Condition: new, 900 mm 900 mm 900x900 mm saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable Fjdpefg E Hpjfx Abuspc • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.

Year of construction: 2007, condition: good (used), functionality: fully functional, machine/vehicle number: 12428 B500-851, Overheadcrane ± 14.170 mm x 25.000 kg Fjdev Ip Afspfx Abuopc

Year of construction: 1998, condition: good (used), functionality: fully functional, machine/vehicle number: 13354 B521 850, Overheadcrane ± 10.500 mm x 12.500 kg Fpsdpfev Ip Diox Abusc

Condition: new, Year of construction: 2025, Blast Container High Cube Basic with Sweeping Floor Shovel Hopper for approx. 4 pressure vessel fillings + extra blasting vessel filling, enabling extended blasting time without refilling. Type SC.20FHC.5800 Basic Standard Equipment, ready for operation (just add abrasive and connect power and compressed air): 1x Control cabinet with emergency stop, Siemens Logo controller 1x Pressure blasting vessel 1x Pressure regulator and water separator 1x Blasting hose DN 25 with 8mm blasting nozzle 1x Remote control with dead man's switch Fsdpfx Absw Ivk Tsuepc 1x Abrasive inlet box/hopper 1x Abrasive media sieve + collection container for coarse particles 1x Airwash separator for blast dust extraction (dust reduction during blasting) 1x Filter unit with pre-chamber separator 1x Suction wall with louvre-type impact separator 1x 4mm rubber wall lining with fabric insert 1x Tread plate floor 3/5 1x LED lighting 1x Emergency lighting, door-end switch, emergency stop 1x Breathing air filter 1x Blasting helmet 1x Blasting gloves 1x Coverall/suit Options: - Side Door Open: blast container can be fully opened from the side for easy forklift loading - Container widening - Container extension - Crane roof hatch - 500kg crane runway - C-profile rail for powder coating - Blasting trolley - Filter with big bag - HEPA secondary filter for hazardous dust, e.g. when blasting stainless steel - Stainless steel tread plate floor for stainless steel blasting - Aluminum tread plate floor and much more upon request!

Year of construction: 1998, condition: good (used), functionality: fully functional, machine/vehicle number: 12157 B51 864, Overheadcrane ± 10.500 mm x 16.000 kg Fjdpfov Ip E Hsx Abuopc

Year of construction: 2021, condition: like new (used), functionality: fully functional, machine/vehicle number: 3815407, WEIGHT 8000KG FEM ISO 1Am M4 KW 2.4/15.5 ( 50 Hz) MAXIMUM CAPACITY 16 TON Fodpot Nhqyofx Abujpc

Condition: used, mileage: 322,901 km, power: 130 kW (176.75 HP), first registration: 06/2011, fuel type: diesel, empty load weight: 5,300 kg, maximum load weight: 2,200 kg, overall weight: 7,500 kg, axle configuration: 4x4, fuel: diesel, driver cabin: other, gearing type: mechanical, emission class: euro5, suspension: other, number of seats: 6, total length: 6,200 mm, Year of construction: 2011, construction height: 3,110 mm, Equipment: all wheel drive, Engine runs only at idle, does not respond to throttle input. The vehicle is generally operational, but there are several aspects that should be addressed. Fpedpfx Abondd I Deuec The Unimog U4000 437/25 DoKa EURO-5 is a versatile used off-road truck with a flatbed configuration, suitable for a wide range of industrial applications. First registered in June 2011, the vehicle has a mileage of 322,901 km and is powered by a robust 4.2-litre diesel engine delivering 130 kW (177 hp). Its reliable all-wheel drive (4x4) capability makes it ideal for tough terrain. This used Unimog complies with Euro 5 emission standards and carries a green environmental badge, offering seating for up to six occupants. With compact dimensions (length 6,200 mm, width 2,550 mm, height 3,108 mm), it is fit for both on-road use and demanding off-road environments. The permitted gross vehicle weight of 7,500 kg allows for the transport of heavy loads. Sale to commercial customers only (agriculture, freelancers, small and large businesses) or for export. Errors and prior sale excepted.

Year of construction: 1997, condition: used, Technical details: Rated capacity: 1100 kVA Revolution per minute: 1500 U/min type of fuel: Wasserstoff / Steam / Vapor max. temperature: 420 Grad weight: 3,9 t STEAM TURBINE other data: - Power: normal 560 kW and max. 820 kW - P1 64 bar - P2 11,5 bar Fjdpeu Nvbusfx Abuopc - 1N = 1500 Ampere - Generator type DSG74-M1-4W; 400 V; - Generator nominal power: 1053 kVA / nominal effective power 820 kW - Turbine is suitable for operation with exhaust steam temperature of approx. 405 °C. - A throughput of 2.8t live steam / h in continuous operation is only possible in load-free condition. Sale of the turbine as described and as is! The performance data given are manufacturer's data. These may vary due to age-related wear! We do not have and do not sell spare parts. For spare parts please contact the manufacturer: Dresser-Rand Siemens !!! i.D. *

Condition: good (used), functionality: fully functional, Year of construction: 1991, sheet thickness steel (max.): 16 mm, cutting length (max.): 6,000 mm, HYDRAULIC SHEAR LVD MVSB 62/16 Serial number 18478 Yom 06/1991 Fjdpfjumhm Aox Abuopc TECHNICAL SPECIFICATIONS Max. sheet thickness St45 16 mm Cutting length 6200mm Distance between uprights 6400mm Gap 60mm Range back gauge 1000mm Min. cutting angle 0.5 ° Max. cutting angle 2.5° Min. number of strokes/min. 6 Max. number of strokes/min 25 Min. blade clearance 0.05 mm Max. blade clearance 1.6mm Motor power 30kW Approx weight 35000 Kg LxWxH 7100x2400x3000mm Accessories included; ELGO P85 “GO-TO” for back gauge Electrical adjustment of back gauge 1000mm 1 x Front support 2mtr, one with 90° square arm front support L2000mm Foot pedal Ball bearings on table Inclinable back gauge with manual hydraulic pump