Crane

JMG MC 25S

Condition: like new (used), functionality: fully functional, power: 4 kW (5.44 HP), fuel type: electric, color: silver, overall weight: 2,460 kg, mast type: telescopic, Year of construction: 2022, operating hours: 21 h, machine/vehicle number: 0943, Small, compact, and maneuverable: these are the key advantages of our 2.5-ton electric mobile crane. However, there is no doubt that it is capable of handling “big” tasks, as the crane delivers full performance with a maximum lifting capacity of 2,500 kilograms. The 2.5-ton electric mobile crane comes standard with non-marking tires that do not leave chalk residues. The crane's 2 kW electric motor offers precise control and, thanks to a powerful 24 V, 420 Ah battery, can operate for up to 8 hours without needing to be recharged. The telescopic boom extends proportionally and can be further extended with a jib on request. JMG MC 25S - Capacity 2,500 kg - Net weight 2,460 kg - Width 900 mm Bdodow S Ii Nspfx Aaaoa - Height 1,600 mm - Drive Electric - Power output 4 kW - Tires Solideal Magnum - Hydraulic winch - Telescopic boom - Counterweights - Battery 24 V 420 Ah - Automatic braking system - Front-wheel drive - 2 gear stages - Radio remote control - Manual boom extension - Electronic load monitoring - Boom angle +60° / -15° - Ground clearance 70 mm - Tires - front 18 x 7-8 - Tires - rear 15 x 4.5-8 - Operating manual - Electric motors - Insulation class H

Condition: good (used), functionality: fully functional, power: 180 kW (244.73 HP), fuel type: diesel, color: blue, overall weight: 14,250 kg, maximum load weight: 10,000 kg, tire size: Rubberen rupsbanden 750 mm, number of seats: 1, emission class: euro5, shovel volume: 6.5 m³, Year of construction: 2022, operating hours: 687 h, Equipment: air conditioning, cabin, hydraulics, rear pickup, rubber tracks, === MAIN SPECIFICATIONS === Year of manufacture: 2022 Operating hours: 687 h Payload capacity: 10,000 kg Heaped capacity: 6.5 m³ Struck capacity: 4.7 m³ Engine: Cummins 6.7L Engine power: 186 kW Emission stage: Stage V Fuel type: Diesel Undercarriage: Rubber tracks Track width: 750 mm Track condition: approx. 70% Max travel speed: 16 km/h Gross vehicle weight (GVW): 24,250 kg Unladen weight: 14,250 kg Dump type: Rear tip CE certified: Yes Country of manufacture: Germany === EQUIPMENT & HIGHLIGHTS === Air conditioning Cabin heating AdBlue system Battery master switch Bdsdpfx Aasymxq Heaoa Rotating beacon Rear view camera Automatic lubrication system Cummins 6.7L Stage V engine 10,000 kg payload capacity 750 mm wide rubber tracks Only 687 operating hours Ready for immediate work === CONDITION === Good working condition with normal signs of use. Technically fully operational and professionally maintained. Tracks in approx. 65–70% condition. Inspection possible upon request. === LOCATION & PRICE === Located in Sittard, The Netherlands. Price on request (EXW; excl. VAT). === DELIVERY === Crane loading available upon request. Flexible worldwide shipping options. All transport arrangements professionally handled by Collé Rental & Sales. The Bergmann C912s is a powerful 10-ton tracked dumper designed for demanding construction and infrastructure projects. Equipped with air conditioning, heating, AdBlue system, rotating beacon and rear view camera, it offers both operator comfort and safety. The 186 kW Cummins Stage V engine combined with 750 mm rubber tracks ensures excellent traction and stability in challenging terrain conditions. Low operating hours and ready for immediate deployment.

Condition: excellent (used), Year of construction: 2006, 70 linear meters Pallet Racking SSI Schäfer Palflex incl. Mesh Decks Used, good condition, see photos Year of manufacture: 2006 Height: 4 m Depth: 120 cm Bay load: 12,000 kg Galvanized frames Red beams Bsdpfskx E I Nex Aaaeda Mesh decks included! 2 mesh decks per 2.7 m beam length Negotiable price: €8,290 net ex stock The offer includes: + 26 pre-assembled frames, depth 120 cm, height approx. 4 m + 100 beams, length 2.7 m, 1,500 kg load capacity per level (evenly distributed load) + 200 safety clips + 100 galvanized mesh decks for 50 levels, each with a 2.7 m beam length + 104 concrete anchors + Load signs Goods in stock. Transport and installation available on request. Inspection by appointment at any time. Further information on request. Always over 5,000 linear meters of pallet racking from various manufacturers in stock. (Changes and errors in technical data, specifications and prices as well as prior sale reserved! See our T&Cs, all prices excl. VAT ex stock) Purchase / Sale We are continuously looking for and offering a wide range of items from various sectors clean-sweep business clearances company liquidations fast - flexible - efficient! We also clear out or dispose of assets for administrators. Send us a few keywords – we will contact you promptly. To access our site, please click on our logo!

Condition: used, fuel type: diesel, Year of construction: 2016, operating hours: 955 h, Round tipper Dumper Bergmann 2060Rplus Year of manufacture: 2016 Operating hours: only approx. 950 Payload: 6,000 kg Unladen weight: 4,045 kg Body capacity (struck): 2.5 m³ Body capacity (heaped): 3.6 m³ Body system: hydraulically 180° rotatable and tiltable skip Bdjdpfxjyaa S Es Aaaoa Height: 3,107 mm Width: 2,018 mm Length: 4,489 mm Ground clearance: 2,373 mm Speed: 0-28 km/h Gross weight (road): 7,490 kg, Road payload: 3,190 kg This offer is addressed exclusively to commercial buyers as defined by §14 BGB.

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 61036940, clamping force: 1,600 kN, screw diameter: 50 mm, displacement volume: 393 cm³, injection pressure: 1.892 bar, injection weight: 358 g, mold height (min.): 200 mm, ejector force: 33,000 N, ejector stroke: 100 mm, opening stroke: 950 mm, installation height: 500 mm, total length: 5,650 mm, total width: 1,820 mm, total height: 1,950 mm, overall weight: 9,700 kg, heating capacity: 15.5 kW (21.07 HP), drive type: Vollelektrisch, clear span: 570 mm, tool weight: 600,000 g, Injection molding machines direct from the manufacturer! As the manufacturer KraussMaffei, we offer you our tested and flexible stock machines here: The basic injection molding machine, precisionMolding, offers the perfect entry-level solution for all-electric injection molding, enabling you to react quickly and innovatively to market requirements. It combines high performance, simple operation and short delivery times. It can be used in a wide range of applications, e.g. in the packaging industry, the electrical and electronics industry, medical technology and the automotive industry. Your benefits: - Optimized price-performance ratio for a wide range of applications - High energy efficiency thanks to all-electric machine concept - Realization of demanding delivery times thanks to basic machine concept with a wide range of options TECHNICAL DATA: KM 160 / 750 PA G01 (order 38670011) (machine no.: 61036683, new, year of manufacture 2013) CONTROL  MC P1 with 15" TFT color screen with multi-touch functions CLAMPING UNIT  Clamping force kN 1600  Mold opening force, max kN 120  Clear width (h x v) mm 570 x 520  Clamping platen (h x v) mm 770 x 720  Tool installation height min. - max. mm 200 - 500  Opening width mm 950  Mold opening stroke max. mm 450  Ejector drive electric  Ejector stroke mm 100  Ejector force forwards/backwards kN 33 / 33  Ejector speed forwards/backwards mm/s 300 / 300  Max. Mold weight kg 1200 SPRING UNIT  Screw diameter / type mm 50 / standard  Effective Ls/D ratio 20.2  Injection pressure bar 1892  Stroke volume cm³ 393  Shot weight at max. stroke for PS g 358  Injection speed mm/s 200  Injection flow rate cm³/s 393  Screw drive/speed 1/min 267  Plasticizing flow (standard screw)4) g/s 36.5  Nozzle contact force kN 42 ELECTRICAL PARAMETERS  Connected load kW 31.2  Installed heat output kW 15.5  Power supply V / Hz 400 / 50 3 phases with neutral conductor WEIGHT AND DIMENSIONS  Net weight with switch cabinet t 9.7  Length x width x height m 5.65 x 1.82 x 1.95 ADDITIONAL EQUIPMENT  Low-wear plasticizing  BluePower fully insulated plasticizing cylinder  Open nozzle  Air valve 1 - fold (BWAP)  Pneum. Control hot runner valve gate 1 - compartment  Electrical interface pneum. Cascade 4-fold  Euromap interface handling E18 + E67  Euromap interface (central computer) E67, E77  Water battery 4 - compartment  Electrical preparation for hydraulic auxiliary unit Bdedpeugfw Defx Aaaja  Automatic central lubrication  Adaptive Process Control (APC)  Injection compression molding circuit  Graphic analysis package  Swivel device for injection unit The machine is located in our factory in Parsdorf and is available at short notice. Further additional options can be offered on request. We look forward to your inquiry.

Condition: excellent (used), Year of construction: 1982, Table saw ULMIA 1710s Bjdpfx Asufgnzjaaoda Year of construction 1982 Tilting angle 45° Cutting length on cart 750mm Blade diameter max 250mm. Cutting height 75mm. Cutting width between the saw and the attachment 650 mm Scale carriage for cutting angles Table size 1000x630mm

Condition: new, functionality: fully functional, power: 5 kW (6.80 HP), fuel type: electric, empty load weight: 4,200 kg, Year of construction: 2024, filling bunker with bunker gutter bunker capacity 10.5m³ S355 / St52-3 vibratory feeder with 10mm Hardox 450 wear plate gutter fully stress relieved annealed 2 x imbalance motors 2,5kW Bdjdpfx Aasuqynmsasa NEW

Condition: used, Year of construction: 2021, clamping force: 120 kN, displacement volume: 36 cm³, injection pressure: 2,200 bar, overall weight: 5,400 kg, load hours: 3,500 h, screw conveyor diameter: 22 mm, terms of delivery: EXW (ex Works) delivery time: on request Bdsdpfxjxwy Utj Aaasa terms of payment: 100% prior to delivery

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 61036946, clamping force: 800 kN, screw diameter: 40 mm, displacement volume: 201 cm³, injection pressure: 1,860 bar, injection weight: 183 g, mold height (min.): 150 mm, ejector force: 22,000 N, ejector stroke: 100 mm, opening stroke: 750 mm, installation height: 400 mm, total length: 4,750 mm, total width: 1,670 mm, total height: 1,850 mm, overall weight: 5,600 kg, heating capacity: 11.5 kW (15.64 HP), drive type: Vollelektrisch, clear span: 735 mm, tool weight: 600,000 g, Injection molding machines direct from the manufacturer! As the manufacturer KraussMaffei, we offer you our tested and flexible stock machines here: The basic injection molding machine, precisionMolding, offers the perfect entry-level solution for all-electric injection molding, enabling you to react quickly and innovatively to market requirements. It combines high performance, simple operation and short delivery times. It can be used in a wide range of applications, e.g. in the packaging industry, the electrical and electronics industry, medical technology and the automotive industry. Your benefits: - Optimized price-performance ratio for a wide range of applications - High energy efficiency thanks to all-electric machine concept - Realization of demanding delivery times thanks to basic machine concept with a wide range of options TECHNICAL DATA: KM 80 / 380 PA G01 (order 38670023) CONTROL  MC P1 with 15" TFT color screen with multi-touch functions CLAMPING UNIT  Clamping force kN 800  Mold opening force, max kN 120  Clear width (h x v) mm 470 x 420  Clamping platen (h x v) mm 610 x 560 Bedpfx Aeud H Dmoaaeda  Tool installation height min. - max. mm 150 - 400  Opening width mm 750  Mold opening stroke max. mm 350  Ejector drive electric  Ejector stroke mm 100  Ejector force forwards/backwards kN 22 / 22  Ejector speed forwards/backwards mm/s 300 / 300  Max. Mold weight kg 600 SPRING UNIT  Screw diameter / type mm 40 / standard  Effective Ls/D ratio 20.0  Injection pressure bar 1860  Stroke volume cm³ 201  Shot weight at max. stroke for PS g 183  Injection speed mm/s 200  Injection flow rate cm³/s 251  Screw drive/speed 1/min 334  Plasticizing flow (standard) g/s 24.7  Nozzle contact force kN 34 ELECTRICAL PARAMETERS  Connected load kW 20.6  Installed heat output kW 11.5  Power supply V / Hz 400 / 50 3 phases with neutral conductor WEIGHT AND DIMENSIONS  Net weight with switch cabinet t 5.6  Length x width x height m 4.75 x 1.67 x 1.85 ADDITIONAL EQUIPMENT  Low-wear plasticizing  BluePower fully insulated plasticizing cylinder  Open nozzle  Air valve 1 - fold (BWAP)  Pneum. Control hot runner valve gate 1 - compartment  Electrical interface cascade 4-fold  Euromap interface handling E18, E63  Euromap interface (central computer) E67, E77  Water battery 4 - compartment  Automatic central lubrication  Adaptive Process Control (APC)  Spray embossing circuit  Graphic analysis package The machine is located in our factory in Parsdorf and is available at short notice. Further additional options can be offered on request. We look forward to your inquiry.

Condition: new, functionality: fully functional, power: 19 kW (25.83 HP), gearing type: hydrostat, fuel type: diesel, fuel tank capacity: 35 l, color: yellow, overall weight: 2,098 kg, maximum load weight: 3,000 kg, tire size: 11.5/80-15.3 Mitas TS05, tire condition: 100 %, axle configuration: 4x4, number of seats: 1, emission class: euro5, Year of construction: 2026, operating hours: 1 h, Equipment: UVV, additional headlights, all wheel drive, hydraulics, low noise, MAIN SPECIFICATIONS Year: 2026 Operating hours: 1 h Operating weight: 2098 kg Max. payload: 3000 kg Skip capacity: 1.8 m³ heaped Drive type: Hydrostatic All wheel drive: Yes Differential lock: Yes partial Quick change system: No Cabin: Closed optional Heated cabin: Yes Air conditioning: No Tyres: Rough terrain 11.5 80 15.3 Mitas TS05 Engine manufacturer: Yanmar 3TNV76 Stage V Engine power: 18.9 kW at 3000 rpm Emission class: Stage V Hydraulic flow: 66 l min steering plus 33.4 l min working hydraulics CE certified: Yes HIGHLIGHTS Carefully selected from reliable sources with verifiable history CE certification and complete documentation included Ready for immediate transport and operation Extensive technical documentation available CONDITION Excellent working condition fully inspected serviced and tested by certified professionals. Inspection possible upon request. LOCATION AND DELIVERY Located in Sittard The Netherlands. Worldwide delivery available. Price on request EXW excl. VAT. The Wacker Neuson DW30 is a compact yet powerful wheel dumper with a payload capacity of 3 tons. Equipped with all wheel drive an articulated pendulum joint a Stage V Yanmar engine and an optional closed cabin it delivers top performance stability and safety even under tough conditions. Ideal for construction road works and material transport on rough terrain. DELIVERY Bdsdoxdazaopfx Aaaea Crane loading available on request for smooth transport during shipment. Flexible shipping options tailored to your destination and logistics preferences. All transports are professionally handled by the logistics team of Colle Rental and Sales.