Dust Cyclone Separator

Kairos Engineering Srl

Year of construction: 2022, condition: new, The fabric filter unit consists of one or more insulated compartments containing rows of fabric bags in the shape of round, flat or shaped tubes, or pleated cartridges. The particles contained in the exhausted air move along the surface of the bags, then radially through the fabric. The particles are retained on the upstream face of the bags and the clean gas stream is discharged to the atmosphere. The filter is operated cyclically, alternating with relatively long filtering periods and short cleaning periods. During cleaning, the dust that has accumulated in the bags is removed. Fabric filters collect particles ranging in size from submicron to several hundred microns in diameter with efficiencies generally greater than 99 or 99.9 percent. The layer of dust, or cake of dust, collected on the fabric is primarily responsible for such high efficiency. The cake is a barrier with tortuous pores that trap particles. Pjdpfx Aoibd Azoaaegi

Year of construction: 2023, condition: new, Chopping height max. mm. 200 Infeed width mm. 500 Infeed rollers piece 3 Rotor flight circle mm. 600 Chopping length approx. mm. 20-30 output - output 16 - 20 rm/h chipping Chipper blade piece 2 Feed motors kW 2x2,2 Weight approx. net kg 4100 Pgedpfxsncd Azj Aaasi Inlet : horizontal machine base : steel, inert gas welded Rotor : steel, inert gas welded, dyn. balanced. Bearing : Oversized roller bearings. Bearing housing : Steel, flanged housing. Feed rollers : steel, special toothed. Chip outlet : underneath the machine. Machine grate : (sieve) for secondary crushing of excess lengths. Drive pulley : Matched to main motor N=1500 min-1 Hydraulic system : consisting of: Hydraulic pump, diaphragm accumulator, cylinder, pressure gauge, control valves for lifting of the upper feed roller. Feeding : by 2 gear motors, Make NORD GEAR

Year of construction: 2022, condition: new, Electrostatic filters are considered the most sophisticated technology, currently available, for the collection of solid and liquid particles existing in an exaust air flow. The electrostatic uptake allows the separation of any particle from the air, regardless of its size. In fact, the agglomeration of very fine particles is possible with efficiencies up to 99% on atmospheric dust according to the EN 779 method.The use of electrostatic filters therefore allows to obtain air completely free of dust , smoke, spores, bacteria, pollen ecc . The main advantages deriving from the use of electrostatic filters are: • High filtration efficiency • Low pressure drops • Low operating cost • Limited maintenance interventions Podpfsh Aku Tex Aaaegi • High operating reliability

Year of construction: 2022, condition: new, machine/vehicle number: XXXX, Baffle spray scrubbers are a technology for air pollution control. They are very similar to spray towers in design and operation. However, in addition to using the energy provided by the spray nozzles, baffles are added to allow the gas stream to atomize some liquid as it passes over them. Pjdpfx Aoh Akn Ueaaegi

Year of construction: 2020, condition: new, Available from stock Strip dimensions: 4420 x 34 x 1.1 mm Cutting capacity (square): 360 x 400 mm Cutting capacity (round): 360 mm bundled cutting: 180 - 280 x 50 - 160 mm Cutting speed: 35 - 85 m/min Motor power main drive: 3.75 kW Engine power hydraulic pump: 0.75 kW Motor power coolant pump: 0.125 kW table height: 755 mm Weight: 1680 kg Pgjdpfeiryf Ssx Aaasi Dimensions W x D x H: 2400 x 2120 x 1840 mm

Year of construction: 2022, condition: new, The packed bed wet scrubbers is designed to remove gaseous or vaporous pollutants from an air stream. The process is accomplished by contacting the contaminated air stream with a scrubbing liquor that absorbs or chemically reacts with the pollutants. The cleaned air is then discharged to the atmosphere and the contaminated scrubbing liquor is either disposed of in the approved can be recovered and reused in the original on other processes. In the vertical counter-current design, gas flows upward while scrubbing liquid flows down through banks of sprays. The absorption of gases takes place in the scrubbers random packing section and scrubbing liquid is introduced into a liquid through or spray distribution system. A high-efficiency mist eliminator removes entrained liquids. Clean gas go directly in the atmosfere . Podpoh Apkdefx Aaaegi

Year of construction: 2022, condition: new, The Venturi Scrubber is a device that generally consists of a centrifugal part capable of separating the solid parts from the liquids and of a Venturi column that narrows in the middle section to vary the pressure and therefore allow the polluting solid particles to fall through the fumes. This type of Scrubber is used for the removal of dust and pollution present in corrosive and dangerous industrial gases. Venturi Scrubbers are used in the abatement of particulates that come from coal, oil or wood boilers, the textile industry but also for emissions from the chemical industries, wood industries, paper mills, etc. Pgodpfx Aajh Atp Ajaei

Year of construction: 2012, condition: good (used), Muratec MW120 GT for sale Used, in excellent condition. The machine can be viewed by appointment. Delivery is the customer's responsibility, but we can help with packing and loading of need. Podpfxoifi D Ts Aaaogi Delivery: EXW Székesfehérvár

Year of construction: 2022, condition: new, Kairos Engineering's energy recovery system is a technology that recovers the heat contained in the industrial hot wastewater, to transfer it to other water to be put back into the production process. The transfer takes place by means of shell and tube heat exchangers in which the two fluids, which never meet directly in order not to undergo contamination, they are sent against the current, that is, one against the other. Indicative savings of 30%. Pgjdpjh Akv Hofx Aaaoi

Condition: good (used), Year of construction: 2017, operating hours: 10,963 h, functionality: fully functional, machine/vehicle number: ML0335-000100, turning diameter over cross slide: 400 mm, turning length: 550 mm, turning diameter: 350 mm, spindle bore: 76 mm, spindle speed (max.): 4,500 rpm, travel distance X-axis: 205 mm, travel distance Z-axis: 560 mm, spindle motor power: 12,600 W, rapid traverse X-axis: 30 m/min, rapid traverse Z-axis: 36 m/min, total height: 1,693 mm, total length: 2,570 mm, total width: 1,595 mm, workpiece weight (max.): 300 kg, overall weight: 3,400 kg, bar passage: 67 mm, Equipment: documentation/manual, rotational speed infinitely variable, very stable roller-guided 2-axis CNC lathe with tailstock, suitable for both series production and single-part machining; Siemens 828 D control; interface for bar machining, parts catcher and ejector for automated processing; tailstock; chip conveyor; various tool holders; tool measuring arm. Pgedeydbqqspfx Aaaji