Overband magnet Block magnet Magnetic plate

mütek Hawk-Eye

Condition: new, Year of construction: 2025, Diameter: 160mm Also available in the diameters: 180, 200, 250, 300 mm for an additional charge, other diameters on request. Iedpfx Aschuvreddjht Very stable industrial design. Ideal for separating nails/metal parts from material flows. For example after a wood shredder. including 3 extremely powerful magnets * If desired, up to 6 magnets can be installed in the component - surcharge for each additional magnet + 49 € - Neodymium magnets are also available instead of ferrite for an additional charge Your advantages: + Extremely large inspection door with seal for easy stripping of the nails + Stable quick-release fastener +Made in Germany Inspection door / opening: 35x18 cm Installation length may vary

Condition: used, functionality: fully functional, load capacity: 18,000 kg, lifting height: 11,900 mm, fuel type: electric, mast type: telescopic, construction height: 1,990 mm, empty load weight: 21,650 kg, total length: 5,540 mm, drive type: Elektro, construction width: 2,000 mm, Pick & Carry Crane Mast type: Telescopic Technical condition: good Front tires type: Non Marking Rear tires Type: Non Marking Ijdpjt Dd Uwofx Addoht Remote control

Year of construction: 2025, condition: new, *Only the neodymium overbelt magnet is offered, not the conveyor belt underneath. *Neodymium magnets are among the strongest magnets in the world. They have an extreme pulling power and cannot be compared to ferrite magnets. Extremely high degree of separation, depending on the bulk height and the starting material. Ihsdpfx Adjdubpujdst Probably the most compact overband magnet on the market. The competition often uses the less powerful ferrite magnets to save costs. dimensions approx. Length: 104cm Width: 22cm Height: 28 cm (at the motor) *Without controller Surcharge for simple manual start/stop control + 495 € A high-performance industrial neodymium magnet is installed. High-performance neodymium magnet approx. 600x68x36.5 mm * So nails are attracted to a length of 600 mm and thrown off to the side, in the area that is no longer magnetic. This overbelt magnet should be mounted approx. 5 - 9 cm above the material flow. *Assembly/suspension on site Ideal for separating nails from wood chips. Optionally also in a single-shaft shredder that is sucked off Requirements: *Your belt width or useful width inside (of the existing conveyor belt) should ideally be narrower than 55 cm *Suitable for separating nails from material flows that are less than 12 mm high and with a chip length of less than 25 mm. ----- Optional at extra charge: Cross and ascending belt demonstrators from € 7,995 net

Condition: good (used), functionality: fully functional, Opening: 620 x 350 mm Rotor-diameter x -width: 1.060 x 610 mm Ihsdpfx Adelgzrhjdst feed size hardrock -180 mm feed size limestone -300 mm, complete with E-drive, conveyor and steel-construction

Year of construction: 2019, condition: refurbished (used), Overband plate magnet Version in VA 1.4301 tightly welded Ihodsd Dzahspfx Addst 420 x 250 x 100mm completely welded housing Ring eyelets for suspension

Year of construction: 1979, condition: ready for operation (used), A Gebr. Pfeiffer ball mill is available. Drive power: 330kW, diameter: 2400mm, length: 5000mm, number of motors: 2, motor weight: 180kg, flywheel width: 3.2mm. On-site inspection is possible. Ihodpfx Aov Dwiroddjt

Condition: new, Year of construction: 2024, MONOBLADE EDGER lenht of cut from 4,2 to 8,2 mt Ihsdpfx Adefw Nv Rsdot max depth of cut 160 mm parallel guide hopper

Condition: good (used), Year of construction: 1992, functionality: unexamined, overall weight: 18,000 kg, power: 250 kW (339.91 HP), For bulky waste, pallets, residual wood, etc. Single-shaft shredder with electrohydraulic drive Rotor width: 2500 mm Ihsdpfx Adeq I Rkdedot Rotor diameter: approx. 500 mm Electric motor: 250 kW

Year of construction: 2021, condition: new, Complete solution for the transport of bulk materials and demetalization of magnetic metal contaminants. Aluminum ascending conveyor belt including substructure Incline start area level ground (adjustable) Discharge height 1800mm (adjustable) Construction: height adjustable Construction for suspending the overband magnetic separator DMPM1200 included Conveyor belt width 500mm (adjustable) We deliver our conveyor belts in PVC, PU or rubber. PVC conveyor belt including carrier and corrugated edge Drive: Motor 0.25KW (adjustable), speed 0.3m / sec Connection 220 / 240V, 50Hz, protection class IP54 Drive etc. ready for connection, motor control optional 6x adjustable machine feet for alignment Wave edge: 40x35mm T-20 studs - 400mm pitch 2-ply particularly cross-stable Iedpjhh A Iysfx Addoht Our core competence lies in delivering exactly what the customer really needs. We work together with our customers to develop customer-specific, individual solutions and deliver corresponding systems from our own production. Feel free to contact us by phone to find a suitable solution for your application. Conveyor belt, conveyor belt system, discharge belts, belt conveyors, magnetic separators, overbelt magnetic separators, recycling, wood chips, plastic, metal-free metal detection, neodymium, overbelt magnets, magnetic belt separators, lifting magnets, filter rods, magnetic grids, magnetic grids, metal separators, block magnets, filter systems

Condition: reconditioned (used), Year of construction: 2007, - Primary impact crusher, Brand Laron Model IM 16 Ihedpeimwg Hsfx Addot - Complete assembly, available as mobile or static unit. - New rotor bearings - New rotor blow bars - Front jaw (impact plate) in near-new condition - Production capacity: 800 t/h - Feed opening: 2320 x 1700 mm. Motor: 600 HP - New bearings and supports - New rotor blow bars - Apron feeder: width 2000 mm, length 10,000 mm. Gearbox and 40 HP motor. Feeder condition: semi-new - Disc pre-screen: width 2000 mm, diameter 1000 mm. Gearbox and electric motor - Hopper with 40 m³ capacity. Bolted and sectional for easy transportation - The entire assembly is mounted on a chassis with tractor head coupling and can be transported on dolly axles. We also have secondary hammer mills, screens, and conveyor belts available to complete a plant.