Cone Crusher Svedala

Year of construction: 1990, condition: repair required (used), Mobile jaw crushing system, operating hours approx. 10.000, engine Caterpillar 6 cylinders with generator set approx. 35 KVA, year of construction approx. 1990, jaw crusher KUE-KEN (KK114 inlet 1140 x 750 mm) incl. magnetic tape (iron separator), total weight 48 tons on semi-trailer chassis. Condition: Motor and conveyor systems run perfectly, only the drive shaft of the crusher is defective (damage approx. € 17.000) Hedpjhz Dmgjfx Ah Ujg

Condition: used, Tube bending machine, mandrel bending machine, bending machine for tubes and profiles Tube bending unit with SIEMENS servo motor and planetary gearbox Year of construction: 2003 Bending capacity: max. Ø 20 x 1 mm Hsdpfx Ahed E A I Io Usg Bending radius: max. R 70 mm Bending angle: max. 200° - last used for round tube Ø 15.4 x 0.8 mm, R60 mm - Bending tools and bending jaws interchangeable - Bending tool drive via AC servo motor and Alpha spur gear, planetary gearbox - 2-part bending tool opens and closes via hydraulic stroke movement - MERKLE hydraulic round block cylinder, item 014445 for hydraulic tool opening - Pneumatic height adjustment of the bending jaw via Festo compressed air cylinder - without electrical control - without hydraulic unit Dimensions L/W/H 760 x 400 x 150 mm weight: approx. 60 kg good condition Removed from a functional special machine, tested before removal. Drive: Brushless permanent magnet servo motor SIEMENS Typ:1FK6061-7AF71-1EG0 Nominal torque = MO: 6.4 Nm Rated current = Io: 6.1 A Speed = n. max.: 5500 rpm - Brushless permanent magnet servo motor SIEMENS ----- 5 pieces available in right-hand version. 5 pieces available in left-hand version. The price quoted refers to 1 bending unit with servo motor. If required, we also sell individual assemblies of the bending unit. We also offer the electrical components for controlling the servo motor. We also offer hydraulic units.

Year of construction: 1982, condition: good (used), machine/vehicle number: 14320, Vertical Baling Press Hodpfx Aheiuky Ie Ujg

Condition: good (used), 10,000 pieces Inserted gratings Gratings for pallet racks galvanized Inlay grids in different sizes, mesh sizes, load-bearing bar and weight load available: Negotiation price: from € 15,-- net per m² from stock Larger quantities on request! Insertion grid Mesh width Load bearing bar Load bearing bar direction 100.5 x 98.5 cm 7 x 3.5 cm 35 x 2.5 mm 100.5 cm 120 x 89.5 cm 7 x 3.5 cm 30 x 2.5 mm 120 cm 118 x 109 cm 7 x 4.5 cm 45 x 2.5 mm 118 cm 133 x 99 cm 3 x 3 cm 30 x 2 mm 99,5 cm 134 x 75 cm 7 x 7 cm 25 x 3 mm 75 cm 134 x 76.5 cm 2.5 x 2.5 cm 20 x 2 mm 75 cm 134 x 92 cm 6.5 x 6.5 cm 30 x 2 mm 92 cm 134.5 x 99.5 cm 7 x 7 cm 30 x 2 mm 99.5 cm 143.5 x 124 cm 7 x 4.5 cm 35 x 2 mm 124 cm Second-hand, very good condition, see pictures. Goods are in stock. Transportation possible on request. Visits possible at any time by appointment. Further information on request. Constantly over 5000 running meters of pallet racking from numerous manufacturers in stock. (Changes and errors in the technical data, information Hodpfxjd Hvvge Ah Uog and prices and subject to prior sale! See our AGB, all prices excl. VAT from stock) Purchase / Sale We are constantly looking for and offering numerous articles from various areas clean-swept premises Liquidations quick-

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: Hjdpfx Aovwlqqeh Usg The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: like new (used), 1500 m² storage platform Schäfer R3000 3-story used, top condition, as new, see pictures Ground floor storage platform steel construction, above 2 floor shelf system Schäfer Hjdpfx Ahohzw His Ueg Manufacturer SCHÄFER R3000 CAD planning and assembly 3-storey Partial sale possible Negotiation price: on request! Goods are in stock. Transport and assembly possible on request. Viewing possible at any time by appointment. More info on request. Constantly over 5000 running meters of pallet racks from numerous manufacturers in stock. (Changes and errors in the technical data, specifications and prices and prices as well as prior sale reserved! See our terms and conditions, all prices excl. VAT ex stock) Purchase / Sale We are constantly looking for, or offer numerous items from various areas broom-clean business clearances company liquidations Fast- flexible - ready to hit! We also clear and dispose for liquidators. Write us with some keywords, we will contact you immediately. To get to our site, please click on our logo!

Condition: ready for operation (used), Year of construction: 1989, Used single-toggle jaw crusher 1300 x 900 mm, including spare shaft and FAG 23152 K MB C3 bearings. Year of manufacture and make are unknown. The crusher operated reliably until 2023 and was then replaced with a mobile plant. Hodpjwmgw Njfx Ah Ueg

Condition: excellent (used), Year of construction: 2015, operating hours: 14,900 h, functionality: fully functional, overall weight: 33,000 kg, power: 264 kW (358.94 HP), rotational speed (min.): 70 rpm, input voltage: 400 V, Slow-running, robust single-shaft shredder suitable for pre-shredding a wide variety of materials without solid contaminants. Application: Shredding of industrial and commercial waste, foils, packaging materials, textiles, paper, rubber, demolition wood, pallets, paper rolls, cable drums, and mixed plastics for thermal and recycling purposes, loose or baled. Lindner Jupiter 2200 Drive power: 2 x 132 kW (ABB motors) Screen perforation: According to customer requirements. mm Control cabinet: complete with (FU-ABB) Working opening: 2135 x 1750 mm Filling volume: approx. 5.5 m3 Rotor length: 2200 mm Rotor flight circle: 745 mm Hedpfsv S Hyvjx Ah Ujg Rotor speed: 50 Hz: 87 rpm Number of rotor blades: 84 Blade shape: 172 x 57 x 28 mm Lower anvil blades: 6 Upper scraper combs: 6 Hydraulic feed: 11 kW Total weight: approx. 33 t Dimensions LxWxH mm: 5500 x 3050 x 3100 mm, with hopper H = 4880 mm Delivery time: immediately Two discharge belts available as an option.

Condition: good (used), Year of construction: 2002, operating hours: 11,245 h, machine/vehicle number: CCC00513, 239 kW weight: 50,5 t engine complete overhauled tracks as new Hjdpfx Aolhqhmsh Usg new cylinder-sealing

Condition: not inspected (used), Hydraulic press for pressing paper etc. materials. The device was operational before disassembly. Press dimensions: Hedpfeh Nyfyex Ah Uog length 4850 mm, width 1370 mm, height 3000 mm (possibility of reduction 2300 mm). Weight 3500 - 4000 kg. If you have any questions, please contact us at 539 660 495.