Used Angulus Guideline for sale (190)

Condition: used, Technical Commercial Datasheet – Integrated KAESER CSDX 165 T Air Compressor Station Manufacturer KAESER KOMPRESSOREN (Coburg, Germany) Type Complete "All-in-One" industrial compressed air station, featuring a fluid-injected rotary screw air compressor with variable speed control (CSDX Series), an integrated refrigeration air dryer (Module T), and an advanced SIGMA CONTROL 2 electronic monitoring configuration. Industrial Applications Continuous, high-efficiency plant air generation for automated manufacturing facilities, heavy assembly lines, packaging plants, plastics processing, and automotive industries. The variable speed drive system matches actual compressed air consumption in real time, eliminating peak starting currents and optimizing plant energy performance. Key Technical Specifications * Main Compressor Unit: KAESER CSDX 165 T (CSDX Series / Integrated Dryer Version) - Technology: Fluid-injected rotary screw compressor featuring premium SIGMA Profile rotors - Regulation System: Variable speed control via an integrated frequency inverter (SFC / Sigma Frequency Control) - Nominal Motor Power: 90 kW - Air Flow Range: Dynamic adjustment based on plant load profile (up to approximately 16.15 m3/min maximum capacity) - Maximum Working Pressure: 8.5 bar max (Current digital setpoint displayed: 7.5 bar) - Integrated Air Dryer (Module T): Refrigeration air dryer utilizing eco-friendly R-513A refrigerant (2.6 kg charge), with a maximum pressure of 32 bar on the cooling circuit side. Hedjzcaufopfx Ahast - Electrical Requirements: 400 Volts / 3-Phase / 50 Hz - Control Interface (SIGMA CONTROL 2): - Total running hours: 26,805 h - Hours under load: 15,272 h - Current system pressure: 0.00 bar (at standstill) / Internal package temperature: 24 °C Machine Utilization This KAESER CSDX 165 T workstation draws ambient atmospheric air and compresses it through its high-efficiency 90 kW fluid-injected screw airend. The frequency inverter continuously regulates the engine speed to prevent the unit from wasting power during low-demand windows. Saturated, hot compressed air exiting the screw block is directed straight into the built-in refrigeration dryer module (Module T). The dryer chills the air stream down to its pressure dew point, condensing and safely discharging moisture to deliver clean, dry, and precisely regulated air to the factory floor line. System Highlights * Compact All-in-One Workstation Footprint: By enclosing the compressor and the refrigeration dryer unit inside a single acoustically insulated cabinet, the station significantly reduces necessary floor space, transport overhead, and engineering installation costs. - SFC Variable Speed Energy Efficiency: The dynamic matching of motor output to actual pneumatic network demand ensures a highly optimized electrical power factor and an exceptionally competitive cost per cubic meter of air. - Intelligent SIGMA CONTROL 2 Management: This interface monitors all critical operating metrics (pressions, temperatures, and maintenance schedules), ensures advanced industrial network compatibility, and confirms a healthy machine history with low un-loaded idling hours (only 43% idle time relative to total run metrics). - Future-Proof Eco-Refrigerant: The integration of R-513A refrigerant meets strict international F-Gas environmental guidelines, securing the long-term operational legality of the cooling loop without risks of sudden regulatory phase-outs.

Condition: new, functionality: fully functional, color: orange, operation weight: 2,300 kg, drive condition: 100 %, chain condition: 100 %, number of seats: 1, Year of construction: 2026, Equipment: additional headlights, cabin, gripper hydraulics, hammer hydraulics, hydraulics, rubber tracks, HITACHI 23U-6 MTC with an operating weight of approximately 2,360 kg and a FULLY HYDRAULIC 360° OILQUICK OQR30 quick-change system - Base unit 23U-6 MTC - Cab and blade - 230 mm rubber tracks - 970 mm boom - Monoblock boom, laterally adjustable - Leak oil line - Automatic release for hammer/grapple - Hammer/shears and grapple hydraulics > all operated via the joysticks - IFM monitor for switching the auxiliary circuit Attachments: Rotator OILQUICK OQR30-R02 Demolition and sorting grapple, 300 mm cutting width Rigid trenching bucket, 1,200 mm cutting width Grading bucket, 800 mm cutting width Clamshell – deep excavation grapple, 400 mm cutting width Hedszg E H Hspfx Ahajt Manufacturer's warranty: 60 months or 3,000 operating hours, whichever comes first, in accordance with the manufacturer's guidelines. All wear parts are excluded. Inspection possible at any time. Financing and leasing available upon request.

Condition: as good as new (ex-display), Year of construction: 2024, Pre-crusher Base machine starting from €29,950 net *Options available at an extra charge Ideal for pre-crushing bulky materials such as pallets, planks, beams, fruit crates, polystyrene, plastics, and more. To produce wood chips, the pre-crusher can also be installed directly above a single-shaft shredder. Machine in pre-production *Special options available at an extra charge Your advantages: + Volume reduction of up to 70% + Significantly lower transport costs + Low disposal costs + Production of fuel material + Also ideal as a pre-crusher for a single-shaft shredder to produce wood chips Weight: 1,200 kg Dimensions: 2050x850x1600 mm Cutting head opening: 1300x700 mm *also available optionally in 1600x700 mm (motor then 11 kW) (Extra charge: + €4,995 net) Hjdpfx Ahsfd Icisast Throughput: up to 50 pallets/pieces per hour *strongly material-dependent Motor: 7.5 kW Options: Industrial hopper attachment (3-sided closed) + €4,950 net Extra emergency/off button + €495 net 200 mm extension + €497 net Requirements for the raw material: - Moisture content less than 30% ATRO - The machine must be installed in accordance with CE guidelines, and measures must be taken on site to prevent access from below (into the cutting head). - Pallets up to a size of 1200x800 mm can be processed. - Longer parts can also be processed vertically.

Year of construction: 2010, condition: used, machine/vehicle number: HO1, Used Tetra Pak 4.3 T aseptic homogenizerTechnical Specifications & Performance DataThis industrial homogenizer is engineered for high-pressure processing and reliable particle-size reduction across beverage and food applications. Manufactured by Tetra Pak, the TA200 platform is recognized for stable operation, hygienic design, and robust components suitable for continuous-duty production. This unit is associated with a 250 bar rating, aligning with common requirements for dairy, juice, and beverage processing prior to filling and packaging on a used bottling line or second hand industrial packaging system.Manufacturer: Tetra PakModel: TA200Pressure rating: up to 250 bar (as indicated on the machine type plate)Design intent: High-pressure homogenization for beverage productionCE marking: PresentAseptic capability: Includes preparation/upgrading to aseptic homogenizationApplication scope: Beverage production and industrial packaging linesAdvanced Automation & Control SystemsThe TA200 platform from Tetra Pak is designed to integrate with modern automation architectures used in beverage production. Typical interfaces support upstream and downstream synchronization with processing and bottling equipment. Operator-friendly controls and clear status indication help maintain repeatable results and reduce downtime.Integration-ready control interfaces for line automationProcess monitoring for pressure and flow stabilityDesigned for consistent homogenization performance at set pressureSafety interlocks aligned with industrial practiceProduction Line Integration CapabilitiesThis homogenizer is suitable for installation upstream of fillers and other bottling equipment within a used bottling line or a second hand beverage production plant. Its aseptic upgrade preparation supports integration into hygienic and ultra-clean process segments where product protection and shelf-life are priorities.Compatible with standalone or inline operationInterfaces with mixers, pasteurizers, and fillers in industrial packaging linesFlexible placement before filling of PET or glass containersSuitable for multi-product beverage workflowsMachine Condition & Maintenance HistoryThe unit is presented for sale with inclusion of preparation/upgrading to aseptic homogenization. It is positioned for rapid commissioning into beverage production environments. Routine maintenance practices can be applied in accordance with Tetra Pak guidelines to preserve performance and reliability.Commercially offered as a second hand industrial assetReady for operation subject to standard installation and commissioningOperational Performance & VersatilityHigh-pressure homogenization improves stability, mouthfeel, and product uniformity, enabling downstream filling into PET and glass packaging. The TA200 platform is widely used in beverage production where consistency and quality control are essential.Stable particle-size reduction at defined ... Hjdpfx Ahszd Ul Tsast

Year of construction: 2013, condition: good (used), BHT INNOVA E3 Professional Bronchoscope Washer INNOVA – Professional Endoscope Washer for Practices and Small Clinics The INNOVA™ E3s is the world's best-selling BHT endoscope washer. This endoscope washer is compact and offers a high capacity for endoscopes or bronchoscopes. Depending on the reprocessing, a total of 10 to 20 endoscope reprocessings are possible daily. This makes it the perfect solution for private medical practices and small clinics that value safe hygiene, efficiency, and reliability. Reliability and maximum cleanliness in every cycle: Compliant with DIN EN ISO 15883-1/-4 and the guidelines of the Robert Koch Institute (RKI), and with many additional functions, e.g., thermal self-disinfection at 90°C according to DIN EN ISO 15883-4, 4.8.1. - Flexible in combination with another INNOVA® E2 or E3 for 30 to 40 reprocessings daily. - Suitable for both glutaraldehyde and peracetic acid from a wide range of suppliers. Hjdpfxein Edws Ahaet - Suitable for commercially available endoscopes from Fuji, Olympus, Pentax, Storz, and Wolf. - Single-channel connection or patented pressure chamber available. - Thermal reprocessing option, e.g., for multiple biopsy forceps, polyp loops, etc. - Thermal disinfection of the final rinse water as recommended by the Robert Koch Institute (RKI) for the DH version. - Secure documentation and traceability through batch control. User and endoscope identification via barcode scanner. - Data output via printer, data logger, or computer interface. Easy integration into existing IT systems Number of endoscopes: For 2 endoscopes or 4 ENTs Hygienic design: Hygienic workflow, single-door Channel connection system: Single-channel connection or patented pressure chamber system possible Single-channel monitoring system (CMS): No Chemistry Glutaraldehyde / Peracetic Acid: Both possible: DH version (with boiler, for glutaraldehyde) or DC (filter solution, for glutaraldehyde or peracetic acid) Documentation and integration: Yes, interface for printer/data logger as standard. Printer as standard. Optional scanner/IT interface Thermal reprocessing of instruments at 90°C: Available with additional equipment Electrical installation: 3-phase 400 V / 50 Hz AC+N+PE. Connected load: 11 kW. Fuse rating: 3 x 20 A Year of manufacture: January 19, 2013 Item condition: used Financing through our bank is also possible. komplett-konzept.leasingo.de Find more items - new and used - in our shop! International shipping costs on request!

Condition: like new (used), GIF Kitchen Ventilation Ceiling Ventilation Ceiling System The optimal solution for kitchen ventilation, commercial kitchens, and the food industry. The best alternative to extractor hoods GIF kitchen ventilation ceilings are installed in: • Company canteens • Hospitals, clinics • Restaurants / hotels • Retirement homes, homes for the disabled, and children • Military accommodations, field kitchens • University cafeterias, school kitchens • In-flight catering • Correctional facilities • Public facilities Patented quality – Made in Germany The GIF kitchen ventilation ceiling is a complete, wall-to-wall, surface-active solution including large-area exhaust and supply air panels, lighting, and compensation surfaces with an installation height of just 200 mm. The use of the ceiling cavity as a pressure chamber in accordance with VDI 2052 enables implementation as an "open" or "closed" system, always maintaining the largest possible proportion of air-active surfaces. The large-scale capture of frying, cooking, and other fumes, as well as the large-scale, low-turbulence supply air intake, guarantee a comfortable climate free from condensation and drafts. The unique modular system offers maximum transparency and hygiene thanks to its fully reversible design. The unique modular system offers maximum transparency and hygiene thanks to its fully reversible design. On the supply air side, the GIF active cassette ceiling is used for low-turbulence, large-scale supply air intake according to the stratified flow principle. An energy-efficient solution is thus standard. The special design ensures indirect supply air guidance, even for high air volumes at low inlet velocities, without an induction pulse. Since the active cassettes are identical in the exhaust and supply air areas, they can be interchanged at will. Facts and Benefits Complies with or exceeds current guidelines (VDI 2052, VDI 6022, EN 16282), including accessibility to underlying components (no access openings required). Durability of the material: CNS 1.4301 Integrated deflection system for rapid pulse reduction Economical and hygienic cleaning of only 4 parts per m² in the dishwasher Pulling and pushing of the active cassettes in the support profiles makes them easy for anyone to remove without tools Partial cleaning possible as needed No need to climb onto greasy, hot kitchen appliances (risk of slipping) HACCP-certified process Technical Specifications Exhaust Air Air flow rate: 260-300 m³/h m² Separation efficiency: up to 97% Dimensions: 500×485 mm Pressure drop: 20-25 Pa Material/Surface: CNS Material No. 1.4301 Weight per m2 without support structure: 10.00 kg Draft air flow: 360-500 m3/h m2 Dimensions: 500×485 mm Pressure drop: 25-30 Pa Material/Surface: CNS material No. 1.4301 Weight per m2 without support structure 10.00 kg Airflow velocities: less than 0.2 m/s Ceiling area: 6500 x 3000 mm 19.50 m² Hodpjt Hglkjfx Ahaot 300 supply air flat ceilings, 250 x 485 mm 200 supply air flat ceilings with sound absorption, 250 x 485 mm 220 active cassette ceilings, 500 x 485 mm 14 system support profiles, 6500 mm 7 system support profiles, 2000 mm Lighting fixtures installed flush with the ceiling in the GIF ventilated ceiling Financing through our bank is also possible. komplett-konzept.leasingo.de Further items in other sizes – new and used – can be found in our shop! International shipping costs upon request!

Condition: new, Year of construction: 2026, pressing force: 500 t, DURENDUS 500 T Workshop Press – C-Frame Press – 1,600 mm Clear Width, 550 mm Stroke The machine shown here was built and delivered to a customer as a custom order. We can manufacture this machine for you on very short notice – with pleasure also considering individual options. This is a hydraulic workshop press designed for pressing, straightening, and assembly work in workshop and industrial environments. Base price: €46,950 net Options (on request): The listed options are based on completed customer projects and allow for targeted adaptation of the machine to each specific application. The base machine is a functional standard version – in most cases, it is supplemented with additional features and configurated specifically for the project. * Table plate with X-shaped T-slot 800 × 1,200 × 120 mm * Pressure adjustment * Lateral displacement of the press ram (1,000 mm) * Bending tool * Anti-rotation cylinder with manual travel adjustment * V-profile straightening anvil in combination with table plate Hedoy H Drwspfx Ahajt * LED lighting * Foot switch * Cooling ===== Technical Data & Information: ==== General Information * Type: Workshop press * Press force: 500 t (optionally adjustable) * Total weight: approx. 5,000 kg * Overall dimensions (W × D × H): 2,950 × 1,100 × 2,850 mm ==== Working Area * Clear width: 1,600 mm * Open depth: 550 mm * Installation height: 250–900 mm (variable) ==== Table & Ram * Crossbeam usable width: 1,600 / 600 mm * Ram stroke: 400 mm * Cylinder diameter: Ø 400 mm * Piston rod: Ø 265 mm * Height adjustment: via chain mechanism ==== Speeds * Idle speed: 8.6 mm/s * Return speed: 15.3 mm/s ==== Hydraulics & Drive * Pump capacity: 65 l/min * Motor output: 30 kW * Hydraulic tank: 150 l * Pressure accuracy: ±5 bar * Hydraulic system: DUPLOMATIC ==== Control & Operation * Hand lever operation * Manual fine-tuning via hand lever * Connection: 400 V / 50 Hz * Total power consumption: approx. 32 kW ==== Equipment * Height-adjustable crossbeam with pin locking * Chain mechanism for table adjustment * Pressure gauge * Emergency stop switch * CE certification * Two-coat finish to RAL standard ===== Pressing, extracting, assembly work, straightening, workshop applications, maintenance Workshop press, hydraulic press, C-frame press, single-column press, assembly press, straightening press, industrial press Are you looking for a hydraulic press tailored to your application? Contact us for a customized offer. Our hydraulic presses are manufactured in accordance with German machine guidelines, as well as European machinery directives (Directive 2006/42/EC), EC standards, and EU safety regulations. Furthermore, our presses exceed Canadian and European safety requirements, as they fully comply with all aspects of the Brazilian national safety guideline NR 12, which builds on these standards. Our great strength is in special machine construction and press automation. We offer custom-made hydraulic presses at surprisingly affordable prices. For the hydraulic system, we mainly use components from leading European manufacturers.

Condition: new, Year of construction: 2026, pressing force: 400 t, DURENDUS 400 T Workshop Press – Single-Column Press – 1,600 mm Clearance Width, 550 mm Stroke The machine shown here has already been built and delivered as a custom order. We can manufacture this machine for you at short notice – also tailored to individual options as required. This is a hydraulic workshop press for pressing, straightening, and assembly work in workshop and industrial environments. Base price: €35,950 net Options (on request): The listed options are based on realised customer projects and allow precise adaptation of the machine to your specific application. The basic machine represents a functional standard configuration – in practice, it is usually expanded with additional equipment and configured on a project-specific basis. * Table plate with X-shaped T-slot 800 × 1,200 × 120 mm * Pressure adjustment * Lateral movement of the press ram (1,000 mm) * Bending tool * Anti-rotation cylinder with manual travel adjustment * V-profile straightening fixture in combination with table plate * LED lighting * Foot switch * Cooling ===== Hedpfx Aey H Dn Eshajt Technical Data + Information: ==== General Information * Design: Workshop press * Pressing force: 400 t (optionally adjustable) * Total weight: approx. 4,000 kg * Overall dimensions (W × D × H): 2,950 × 1,100 × 2,850 mm ==== Working Area * Clearance width: 1,600 mm * Open depth: 550 mm * Installation height: 250–900 mm (variable) ==== Table & Ram * Crossbeam usable width: 1,600 / 600 mm * Ram stroke: 400 mm * Cylinder diameter: Ø 360 mm * Piston rod: Ø 235 mm * Height adjustment: via chain mechanism ==== Speeds * Idle speed: 7.8 mm/s * Return speed: 13.7 mm/s ==== Hydraulics & Drive * Pump capacity: 48 l/min * Motor power: 22 kW * Hydraulic tank: 120 l * Pressure accuracy: ±5 bar * Hydraulic system: DUPLOMATIC ==== Control & Operation * Manual lever operation * Precise manual adjustment via control lever * Connection: 400 V / 50 Hz * Total connected power: approx. 23 kW ==== Equipment * Height-adjustable crossbeam with pin locking * Chain mechanism for table adjustment * Manometer for pressure indication * Emergency stop switch * CE certification * Two-coat paint finish according to RAL ===== Pressing, extraction, assembly work, straightening operations, workshop applications, maintenance Workshop press, hydraulic press, single-column press, C-frame press, assembly press, straightening press, industrial press Are you looking for a hydraulic press tailored to your application? Contact us for a customised quote. Our hydraulic presses are manufactured according to German machinery guidelines as well as European Machinery Directives (Directive 2006/42/EC), EC standards, and EU safety regulations. Furthermore, our presses exceed Canadian and European safety requirements, as they also fully comply with the Brazilian NR 12 national safety standard, which builds on these. Our great strength is in custom machine construction and press automation. We offer made-to-order hydraulic presses at surprisingly attractive prices. For the press hydraulics, we mainly use components from leading European manufacturers.

Condition: new, Year of construction: 2026, pressing force: 150 t, DURENDUS 150 T Workshop Press – C-Frame Press – 1,250 mm Clear Width, 400 mm Stroke The machine shown here was built and delivered according to a specific customer order. We can supply this machine from stock or manufacture a new one for you – gladly taking individual options into account. This is a hydraulic workshop press for pressing, straightening, and assembly work in the workshop and industrial sector. Base price: €6,900 net Options (on request): The listed options are based on completed customer projects and allow for targeted adaptation of the machine to the respective application. The base version represents the basic functional model – in practice, it is most often expanded with additional equipment and configured to suit specific projects. - Table plate with X-shaped T-slot 700 × 1,000 × 100 mm - Adjustable pressure control - Sideways movement of the ram (900 mm) - Bending tool - Anti-twist cylinder with manual stroke adjustment - V-profile straightening block in combination with table plate - LED lighting - Foot switch - Cooling system ==== Technical Data & Information: ==== General Information Design: Workshop press Pressing force: 150 t (adjustable option) Total weight: approx. 1,400 kg Overall dimensions (W × D × H): 1,800 × 900 × 2,650 mm ==== Working Area Clear width: 1,250 mm Clear depth: 400 mm Daylight: 250–900 mm (variable) Hsdpfx Ahjy Hrkusaot ==== Table & Ram Crossbeam usable width: 1,250 / 670 mm Ram stroke: 400 mm Cylinder diameter: Ø 230 mm Piston rod: Ø 135 mm Height adjustment: via chain mechanism ==== Speeds Approach speed: 8 mm/s Return speed: 12.2 mm/s ==== Hydraulics & Drive Pump capacity: 20 l/min Motor power: 5.5 kW Hydraulic tank: 34 l Pressure accuracy: ±5 bar Hydraulic system: DUPLOMATIC ==== Control & Operation Lever control Manual fine tuning via hand lever Connection: 400 V / 50 Hz Total connected load: approx. 6 kW ==== Equipment Height-adjustable crossbeams with bolt locking Chain mechanism for table adjustment Manometer for pressure display Emergency stop switch CE certification Dual-layer paint finish according to RAL ===== Pressing, removing, assembly work, straightening, workshop applications, maintenance Workshop press, hydraulic press, C-frame press, mounting press, straightening press, industrial press Are you looking for a hydraulic press tailored to your application? Contact us for a customized quote. Our hydraulic presses are manufactured in accordance with German and European machinery directives (Directive 2006/42/EC), EC norms, and EU safety regulations. Furthermore, our presses exceed both Canadian and European safety requirements, as they fully comply with the Brazilian national safety guideline NR 12, which is based on these standards. Our main strength is custom machine building and press automation. We supply tailor-made hydraulic presses at surprisingly affordable prices. We primarily use components from leading European manufacturers for our hydraulic systems.

Condition: new, overall weight: 18,000 kg, axle configuration: 2 axles, Year of construction: 2026, Equipment: ABS, Specification: External Roller 20 AR * Novagrau * 2-axle trailer chassis for containers * External roller version (20AR) * Dimensions and Weights * External reference length approx. 6,896 mm * Overall width approx. 2,500 mm * Ride height loaded approx. 1,175 mm * Roller track length approx. 6,880 mm * Wheelbase 5,100 mm * Unladen weight (complete) approx. 3,860 kg Hsdpfx Ahoyv Ttpeaot * Technical possible gross weight approx. 20,000 kg * Permissible gross weight approx. 18,000 kg * Payload approx. 14,140 kg * Suitable for containers from 5,000 to 7,000 mm length according to DIN 30722 * Chassis with cross members, welded box-section main beams * Made from QSTE steel * 4 container locks, pneumatically operated * Side underrun protection closed according to RL 89/297/EEC * Pivot mounting * Pivot mounting 980 FM incl. ball race ring 90/1100/22 (low maintenance) * Drawbar * Drawbar 2600/980/100/30, towing eye inclined * With height adjustment (tension spring with turnbuckle) * Drawbar with DIN towing eye, internal Ø=40mm, external Ø=110mm, thickness 30mm * Axles * 2 x 10 t axles for 19.5 disc brakes, brand according to manufacturer selection * Brake disc diameter approx. 370mm * Wheel attachment by central centering as per DIN 74 361 part 3 * Brake System * Pneumatic brake system according to EU guideline with Duomatic coupling head * Conventional air suspension * EBS Type 4S/3M, Electronic Braking System with ROLL Stability * Double diaphragm spring-actuated cylinders on rear axle * Release valve for individual release of spring parking brake * Lighting System * 24 Volt full LED lighting system to RL 76/756/EEC with multi-chamber tail light and license plate light integrated in lamp bracket * 1 x 15-pin socket * 6 LED side marker-reflector lights with flash function * 2 LED white position lights at the front * 2 separate LED lane marker lights at the rear * 1 additional reversing lamp * Regional haulage tires, brand as per manufacturer selection * 8 x 265/70R19.5 (7.5x19.5) * Steel wheels ET 138 * Wheel nuts unpainted * Including tire pressure monitoring system * Rear underrun protection made from aluminium * Two vertical Delta anti-collision profiles to protect the rear when loading/unloading * Accessories * 4 plastic fenders (half-shell) front and rear, single wheel fenders * 4 anti-spray mudflaps, neutral * 1 lockable plastic toolbox * 1 wheel chock with holder * 1 A-sign for waste transport * 1 hanging net box * Chassis color: MB7350 Novagrau * Wheel hub color: black KTL * Rim color: RAL 9006 Silver * Rear contour markings: red * Side contour markings: white * Closed SSE: RAL7001 silver grey * Rear panel/light plates: RAL7001 silver grey * Underrun protection: aluminium anodized (silver) All information subject to change. Errors and prior sale excepted.

Condition: new, Year of construction: 2026, pressing force: 30 t, DURENDUS 30 T Workshop Press – C-Frame Press – 700 mm Clear Width, 400 mm Stroke The machine shown here has already been built and delivered as a customer-specific order. We can supply you with this model from stock or manufacture it anew – with consideration for customized options if required. This is a hydraulic workshop press designed for pressing, straightening, and assembly tasks in both workshop and industrial environments. Base price: €3,550 net Options (available on request): The listed options are derived from completed customer projects and enable precise adaptation of the machine to the specific application. The basic model provides a fully functional standard specification; in practice, it is most often enhanced through additional equipment and configured according to project requirements. Cross-grooved T-slot table (from 60 t) Pressure adjustment Lateral movement of the ram (from 60 t) Bending tool (from 60 t) Anti-rotation cylinder with manual travel adjustment V-profile straightening block in combination with table plate LED lighting Foot switch Cooling system ===== Technical Specifications + Information: ==== General Data Design: Workshop press Pressing force: 30 t (optionally adjustable) Total weight: approx. 500 kg Overall dimensions (W × D × H): 1,150 × 700 × 2,350 mm ==== Working Area Clear width: 700 mm Clear throat depth: 300 mm Installation height: 250–900 mm (variable) ==== Table & Ram Crossbeam usable width: 700 / 570 mm Ram stroke: 400 mm Cylinder diameter: Ø 115 mm Piston rod: Ø 65 mm Height adjustment: via chain mechanism ==== Speeds Idle speed: 10.4 mm/s Return speed: 15.3 mm/s Hjdpfxoy Hixce Ahaet ==== Hydraulics & Drive Pump capacity: 6.5 l/min Motor power: 1.5 kW Hydraulic tank: 14 l Pressure accuracy: ±5 bar Hydraulic system: DUPLOMATIC ==== Controls & Operation Hand lever operation Manual fine-tuning via hand lever Connection: 400 V / 50 Hz Total connected load: approx. 2 kW ==== Equipment Height-adjustable crossbeam with pin locking Chain mechanism for table adjustment Manometer (pressure gauge) Emergency stop switch CE certification Dual-layer coating to RAL standard ===== Pressing, ejection, assembly, straightening, workshop applications, maintenance Workshop press, hydraulic press, C-frame press, assembly press, straightening press, industrial press Are you looking for a hydraulic press tailored to your specific application? Contact us for an individual quote. Our hydraulic presses are manufactured according to German machinery directives and European Machinery Directive 2006/42/EC, as well as all EC norms and EU safety regulations. Additionally, our presses exceed Canadian and European safety requirements, as they fully comply with the Brazilian national safety guideline NR 12, which builds upon these standards. Our core strength is custom machine building and press automation. We supply bespoke hydraulic presses at surprisingly affordable prices. Our presses are equipped primarily with components from leading European manufacturers.

Condition: new, functionality: fully functional, Year of construction: 2026, Beam extensions for gantry cranes – increase the reach of your crane Beam extensions are professional accessories for gantry cranes that allow you to increase the working width of the structure. They are used wherever the standard crane width is insufficient – particularly in wide production halls, warehouses and industrial facilities. Manufactured from durable and resistant materials, they ensure reliability and long service life even in intensive working environments. Greater functionality and safety The extensions allow for easy adaptation of the crane to individual requirements, expanding its range of applications without the need to purchase a larger model. The maximum lifting capacity of the crane with extensions is 800 kg. However, it should be noted that when the extension exceeds 200 mm, the load capacity is further reduced. For this reason, it is essential to follow the manufacturer’s guidelines and carry out regular technical inspections of all crane components, including the extensions. Key product features: Enable quick and safe increase of the crane’s working width Simple installation – the set includes two extensions ready for mounting Robust construction – high-strength steel profiles Operational safety – compliant with industrial standards and health and safety requirements Compatible with CORMAK gantry cranes and other structurally compatible models Usage guidelines: Gantry crane extensions should be used in accordance with the manufacturer’s recommendations, particularly with regard to the reduction in load capacity after installation. The minimum extension width is 200 mm, and each additional increase results in a further reduction of the maximum lifting capacity. Regular technical inspections and proper maintenance are essential to ensure full operational safety. Applications of beam extensions The product is ideally suited for industries such as logistics, industrial manufacturing, steel structure assembly, the automotive industry and others. Versatility, durability and build quality make it an excellent choice for companies that expect flexibility and reliability from their equipment. By choosing CORMAK beam extensions, you invest in efficiency, functionality and safety. Extend the capabilities of your gantry crane and adapt it to changing production or warehouse requirements! Technical parameters: Length 520 mm Width 131 mm Hjdpfx Aeycqh Nohaot Height 70 mm Number of pieces per set 2 Set weight 20 kg

Condition: new, axle configuration: 3 axles, loading space length: 10,636 mm, loading space width: 2,480 mm, loading space height: 2,300 mm, loading space volume: 60 m³, Chassis manufactured using a self-supporting aluminum construction Hodpfx Ahefakkcoaet with corresponding reinforcements in the lower belt for particularly high stability and strength, component chassis made of ALUMINUM, 140 mm frame height! (max. 39 tons) Axles and Suspension "Disc brake 22.5" Jost axle assemblies, 3 x 9 tons with DC air suspension, lifting and lowering function, Wabco Smartboard, electronic brake wear indicator (BVA) for display in the central control unit (without central control unit equipment), 1st + 3rd axles can be lifted separately with an assistance function (without central control unit equipment), 3rd axle additionally equipped with Optiturn, ECAS air suspension, tire pressure monitoring Wabco Trailerpulse with ZF rim-mounted sensors Tires and Wheels 6 wheels with tires size 385/65 R 22.5, manufacturer's choice, Alcoa aluminum rims DuraBright-11, 75x22.5 ET 120 kingpin screwed into a 10 mm thick plate Fifth Wheel Aluminum swivel landing gear, 2 x 10 tons support load, for air suspension, we use swivel feet Braking System According to E.G. standard, two-line braking system, EBS E-system Wabco with RSS system (Roll Stability Support), spring brake system acting on two axles with operation at the rear, aluminum air tank system, premium modulator Electrical System According to STVZO guidelines with 2 LED five-chamber lights type Aspöck Europoint LED integrated in the aluminum rear panel, 24-volt system with 1x 5-pole and 2x 7-pole socket, with side marker lights in LED design, 2 separate LED work lights at the rear, 2 LED work lights on the side starting at the 1st axle, at the height of the fifth wheel supports, 1 LED work light inside, at the front left, operated from the outside Body/Tipping Body "Body fully welded inside" Front wall load 17,250 dkn, rear and side walls 10,250/13,400 dkn, aluminum tipping body, side walls 30 mm thick aluminum plank profiles (2-3 mm) 600 mm wide, completely welded with lower and upper belts, plank profiles fully welded inside, floor laid as a sliding floor system on 140 mm aluminum cross members, floor load approx. 7 tons/m2, cross members mounted at a relatively close spacing (approx. 350 mm), aluminum front wall with 600 mm plank profile, 2-3 mm thick in a straight design, special aluminum corner profiles in a beveled design, smooth rear wall in a straight design with 2 aluminum swing doors, 50/30 mm thick, with 4 swivel rod locking mechanisms, attached in the welded aluminum rear frame in Teflon and stainless steel bearings, moving aluminum side wall suspended on the reinforced aluminum upper belt with "Kevlar liner for complete emptying, lateral brush seal and additional Kevlar liner on the side, integrated discharge chute with foldable cover plate in the floor end, operable from the outside, left rear, viewing window at the rear left, 1 sample slide in the rear doors, thus 2 pieces, service door at the front left Hydraulic System "Cargo Floor sliding floor system in the floor with hydraulically moved aluminum profiles on aluminum square profiles with approx. 670 PE-HD gliders, approx. 6mm floor thickness, hydraulics with approx. 200 mm working stroke, fixed mountings on the front wall, separate possibility for connecting the hydraulic line under the vehicle with fixed mountings, line size NW 21, fixed mountings with a size and design to be specified, operating pressure 190 max. 240 bar, aluminum end pieces welded into the floor, electrical operation at the rear left with cable operatio

Condition: new, maximum load weight: 28,320 kg, overall weight: 36,000 kg, axle configuration: 3 axles, loading space length: 13,535 mm, loading space width: 2,480 mm, loading space height: 2,750 mm, loading space volume: 92 m³, Equipment: ABS, Chassis: Design with continuous chassis, newly manufactured in self-supporting aluminum construction with corresponding reinforcements in the lower belt for particularly high stability and strength, reinforced cross members 140mm high (for high ground load), additional reinforcement as a gusset plate in the front lower belt/vehicle frame area, chassis made of galvanized steel up to the support structure. Axles and Suspension: Disc brake 22.5, Jost (DCA) axle assembly design, 3x9 tons with DCA air suspension, lifting and lowering, Wabco Smartboard information center, electronic brake wear indicator BVA readable in the central control unit (display), 1st axle with starting aid (new EC regulation, without central control unit option), (optional, 1st and 3rd axles can be lifted). Tires and Wheels: 6 wheels with tires of size 385/65 R 22.5 according to manufacturer's choice (Br-Go-Co) on silver steel rims, 11.75x22.5 ET 120. Hedefi Nmwepfx Ahaot Kingpin: 2" screwed into a 10mm thick plate. Landing Gear: Mech. support winch with two speeds, 2x 20 tons support load with swivel foot. Braking System: According to EG standard, EBS electronic system Wabco with RSS system (Roll-Stability-Support) and Premium modulator, spring brake system acting on two axles with operation at the rear, aluminum air tank system. Electrical System: According to the guidelines of EG standard 91/633 and 97/28 with 2 five-chamber lights, type Aspöck Europoint, integrated in the aluminum rear panel, 24-volt system with 1x15-pole and 2x7-pole socket, with side marker lights in LED version, 2 reflective panels on the rear, position lights at the front 2x white, rear 2x red, 2 separate halogen reversing lights integrated in the U-profile. Body/Dump Body: Body fully welded inside, reinforced side walls, front wall load 17,250 dkn, side and rear wall 13,400 dkn/10,400, aluminum dump body, side walls 30mm thick aluminum plank profiles (2-3 mm) 600mm wide, completely welded with upper and lower belts, plank profiles fully welded inside, floor laid as a sliding floor system on 140mm aluminum cross members, floor load capacity approx. 9 tons/m2, cross members mounted closely together (approx. 350mm), design with special aluminum corner profiles in a beveled design, smooth rear wall in a straight design with 2 aluminum wing doors 50/30mm thick with 2 swivel rod locking mechanisms, fastened in the welded aluminum rear frame in Teflon bearings and stainless steel bearings, doors secured in the open position with one chain each on the side, hard wear plates on the side walls approx. 2000x1500x4mm, fully welded, moving residual emptying wall with Kevlar sheeting approx. 1800mm length plus side brushes with Kevlar sheeting seal, service door in the front wall with ladder, folding inwards. Hydraulic System: Sliding floor system in the floor with hydraulically moved aluminum profiles on aluminum square profiles with approx. 880 PE-HD sliders plus anti-lifting slide bearings, type CF 10mm floor design, hydraulics with approx. 200mm working stroke, fixed points on the front wall, separate possibility for connecting the hydraulic line under the vehicle with fixed points, line size NW 21, fixed points with size and design to be specified, operating pressure 190-max. 240 bar, aluminum end pieces welded into the sliding floor, electric operation behind the left side with remote control integrated in a lockable waterproof box, without hydraulic hoses. Accessories: 6 PVC mudguards with 2 anti-splash mud fla

Condition: new, axle configuration: 3 axles, loading space length: 13,535 mm, loading space width: 2,480 mm, loading space height: 2,650 mm, loading space volume: 93 m³, Chassis Version with continuous chassis reinforced, new body manufactured in a self-supporting design with corresponding reinforcements in the lower flange for particularly high stability and strength, cross member 140 mm high reinforced version (for high ground loads) additional reinforcement as gusset plate in the front lower flange/vehicle frame area, chassis made of galvanized steel up to the support structure, (trailer construction max. 39,000 kg) Axles and suspension "Disc brake 22.5" Jost (DCA) axle units version, 3x9 tons with DCA air suspension, lifting and lowering, Wabco Smartboard Infocenter, electronic brake wear indicator BVA-readable in the tractor unit (display), 1st axle with traction aid (new EC regulation, without tractor unit equipment), (on request against MP 1st + 3rd axle liftable) Tires and wheels 6 wheels with tires of size 385/65 R 22 .5 according to manufacturer's choice (Br-Go-Co) on silver steel rims, 11.75?22.5 ET 120 Seatposts mechanical support winches with two speeds, 2x 20 ton support load with swivel foot, Braking system according to E.G. standard?EBS E-system Wabco with RSS system (roll stability support) and premium modulator, spring brake system acting on two axles with operation at the rear, aluminum air tank system, electrical system according to the guidelines of the EC standard 91/633 and 97/28 with 2 five-chamber lights type Aspöck Europoint 3 integrated in the aluminum rear end, 24 volt system with 1?15 pin and 2x7 pin. Socket, with side clearance lights in LED design, 2 reflective panels on the rear, 2 white position lights at the front and 2 at the rear. red, 2 separate LED reversing lights integrated in the U-protection Structure/trough "structure fully welded inside" reinforced side walls, front wall load 17,250 dkn, side and rear wall 13,400/10,400 dkn Aluminum trough, side walls 30 mm thick aluminum plank profiles (2-3 mm) 600 mm wide completely welded with lower and upper belt, plank profiles fully welded inside, floor laid as a sliding floor system on 140 mm aluminum cross beams, floor forklift load Hsdpjyh S Aiofx Ahast approx. 9 ton/m2 cross beams mounted accordingly closely (approx. 350 mm), aluminum front wall with 600 mm plank profile 2-3 mm thick in straight design, special aluminum corner profiles in beveled design, smooth rear wall in straight design with 2 aluminum wing doors 50/30 mm thick with 2 pivot rods Locks in the welded aluminum rear frame attached to Teflon bearings and stainless steel bearings, doors secured in the open position with a chain on each side, hard wear plates on the side walls approx. 2,000x1,500x4mm fully welded, running residual emptying wall with Kevlar tarpaulin approx. 1,800 mm long plus side with Kevl. -Plane sealing, service door in front wall with ladder turning inwards Hydraulic system "Cargo - Floor" sliding floor system Sliding floor system in the floor with hydraulically moved aluminum profiles on aluminum square profiles with approx. 880 PE?HD sliders plus anti-lifting slide bearings, type CF 10 mm floor version, hydraulics with approx. 200 mm working stroke, fixed halves on the front wall, separate option for connecting the hydraulic line under the vehicle with fixed halves, line size NW 21, fixed halves with size and design to be specified, operating pressure 190-max. 240 bar, aluminum end pieces welded into the sliding floor, electric. Rear left control with radio control integrated in a lockable waterproof box, without hydraulic hoses Accessories 6 PV

Condition: new, overall weight: 39,000 kg, axle configuration: 3 axles, loading space length: 13,535 mm, loading space width: 2,480 mm, loading space height: 2,750 mm, loading space volume: 92 m³, Equipment: ABS, -Panama Plane 900g -10 mm floor -V-shaped sheet metal 2000x1500x4 -Service door on the front panel -12 pairs of lashing eyes on the front panel Chassis: Design with continuous, reinforced chassis, new body manufactured in a self-supporting design with corresponding reinforcements in the lower chord for particularly high stability and strength, cross members 140 mm high, reinforced design Axle and suspension: Disc brake 22.5 Jost axle assembly, 3*9 tons with DCA - air suspension, lift and lower function, Wabco Smartboard, electronic brake wear indicator BVA, 1st axle with start assist (without SZM equipment) Tires and wheels: 6 wheels with tires size 385/65 R 22.5, premium tires, on steel rims, 11.75*22.5 ET 120 Kingpin: Mechanical support winch, 2x20 tons support load Braking system: EBS E system Wabco with RSS system (Roll Stability Support) and premium modulator, spring brake system acting on two axles with operation at the rear Electrical system: According to the guidelines of EC standard 91/633 and 97/28 with 2 five-chamber lights type Aspöck Europoint integrated in the aluminum rear panel, 24 Volt system with 1*15-pole and 2*7-pole socket, with side marker lights in LED design 2 separate LED reversing lights integrated in the U-shaped protection, Body/tipper bed: "Body fully welded inside", reinforced side walls Aluminum tipper bed, side walls with 30 mm thick aluminum plank profiles (2-3 mm) 600 mm wide, completely welded with lower and upper chord, plank profiles fully welded inside, aluminum front panel with 600 mm plank profile, 2-3 mm thick, in a straight design, with 2 aluminum wing doors 50/30 mm thick, sliding residual unloading wall with Kevlar sheet approx. 1,500 mm long plus side Kevlar seal Hodpfx Asfi Nmpohajt Hydraulic system: "Cargo Floor" sliding floor system Sliding floor system in the floor with hydraulically moved aluminum profiles on aluminum square profiles, mounted with approx. 880 PE-HD gliders, type CF 8 mm floor design, fixed parts on the front panel, separate possibility for connecting the hydraulic line under the vehicle with fixed parts, operating pressure 190 - max. 240 bar, aluminum end pieces welded into the sliding floor, without hydraulic hoses Accessories: 6 PVC mudguards with 2 anti-spray mud flaps, 1 aluminum spare wheel holder, side aluminum approach guard in foldable design, 1 toolbox approx. 860*460*400 mm in plastic, 3.7m aluminum ladder, tarpaulin approx. 660g/m2 with tarpaulin system incl. tarpaulin rail, with side tension straps or quick release fastener, walkway on the front panel with access ladder, 3 steel locking bars with locking mechanism, swiveling and lockable, aluminum protective cover with hinges for the lighting, etc. +590¤ Delivery costs Unladen weight: approx. 7,700 kg Offer and images subject to change.

Condition: new, Year of construction: 2025, Delivery every Monday/Tuesday! Reliable! Mobile folding bench 1400/2.0mm without roller shears We are your partner when it comes to sheet metal working machines. Our claim to ourselves is to provide high-quality and reliable work in order to more than meet your requirements! We are only so successful because we put our heart and soul into our work! Hjdpsb Hqa Eofx Ahast Technical specifications the maximum working length 1400 mm the max. thickness of steel sheet for 2.0mm bending beam 24 mm the weight of the handheld machine is about 190 kilograms lifting the top beam in three layers The maximum clear width between the beams is 80 mm Delivery throughout Germany 165 euros Price: 1450 euros incl. transport rollers Delivery time: every week Cash on delivery The roller scissors (max. cutting capacity up to 0.8 mm / sheet steel) optionally cost 350 euros Manual folding machine costs 75 euros as an option The machine complies with CE guidelines and has a 12-month guarantee. We issue the invoices with 0% (intra-community delivery) as well as with 23%. We are looking forward to your contact!

Condition: new, Year of construction: 2020, functionality: fully functional, tank capacity: 30,000 l, Equipment: documentation/manual, BRINOX 30,000 L WWAS / Solution Tank – 316L – PED – FAT – Complete GMP Documentation – incl. Saddle Supports – 2020 – Like New Manufacturer: BRINOX d.o.o. Tag No.: LV6456-BH1001 Serial No.: 1003464 Year of Manufacture: 2020 Condition: Like new / unused Location: Europe LV6456-BH1001 Package 66 TECHNICAL DATA Product type: WWAS / solution tank / pharmaceutical process vessel Working volume: 30,000 liters Total volume: 33,213 liters Product contact material: Stainless steel 1.4404 (AISI 316L) Surface finish: Chemically pickled, passivated and cleaned Surface roughness: Ra < 1.6 µm Standards and guidelines: • PED 2014/68/EU compliant • CE marking available • GMP-compliant pharmaceutical design Pressure data: Min.: –0.14 bar(g) Max.: +0.5 bar(g) Test pressure: 0.72 bar(g) Temperature range: –20°C to +50°C Hydrostatic pressure test performed. FAT – Factory Acceptance Test Fully documented FAT carried out including: • Dimensional, visual, and identification inspection • Weld seam testing and NDT • Pressure test according to PED • Testing of all connections • Documentation and quality inspection FAT successfully completed. FAT report available. Hodpfx Ahoykngfoajt DESIGN / CONSTRUCTION • Horizontal pharmaceutical process vessel • Stainless steel 316L, pharmaceutical grade • Interior surface pickled and passivated • Hygienic, GMP-compliant construction Connections include: • Manway DN500 • Inlet DN100 • Outlet DN50 • Measuring, safety, and process connections Mechanical configuration: • Original BRINOX stainless steel saddle supports included • Heavy-duty design • Lifting points for crane handling present CONDITION • Absolutely as new • Never installed or used in production • Never filled with product • No corrosion or signs of use • Original industrial packaging available • Immediately available Saddle supports are also as new and included in delivery. DOCUMENTATION – fully available (GMP-compliant) Extensive manufacturer and project documentation including: • EU Declaration of Conformity and CE documentation • PED certificates • Material certificates EN 10204 – 3.1 • Welding documents (WPS/WPQR, welder lists) • NDT inspection reports • FAT protocol and pressure test report • Roughness and surface protocols • Calibration certificates • Part drawings and parts lists • Operation and maintenance manuals Documentation fully available in digital form. TRANSPORT AND PACKAGING • Professional export packaging provided • Original industrial packaging • Crane handling possible without issues • Worldwide shipping possible SUITABLE FOR • Pharmaceutical industry • Biotechnology • WWAS, WFI, and PW systems • Sterile process solutions • GMP production plants SPECIAL FEATURE Project surplus from an international pharmaceutical new-build project with complete FAT, PED compliance, and GMP documentation. Large-capacity BRINOX 30,000 L pharma process vessel in as-new installation quality, incl. saddle supports – immediately available.

Condition: new, power: 129 kW (175.39 HP), fuel type: diesel, overall weight: 3,500 kg, color: grey, gearing type: automatic, emission class: euro6, number of seats: 7, loading space volume: 12 m³, loading space length: 3,540 mm, loading space width: 1,800 mm, loading space height: 1,900 mm, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), navigation system, Welcome to carmax24! Today you have the opportunity to purchase one of our selected, inspected vehicles. Expertly assessed and high-quality vehicles have been ensuring high customer satisfaction since 2008. This is our daily commitment, because at carmax24, you, the customer, always come first. RENT-TO-OWN • LEASING • FINANCING AT TOP RATES NEW MODEL: Iveco Daily 35S18HA8 V - 7 seats Wheelbase 3520 mm, single rear axle wheels Color: Grey IC 370 EURO 6 engine: 3.0-liter diesel Maximum output: 176 HP (129 kW), maximum torque: 400 Nm at 1500 rpm, 4 in-line cylinders, Turbocharger with variable geometry (eVGT) Transmission: AUTOMATIC HI-MATIC Equipment highlights include: - 00676 Reversing camera with guideline assist - 00726 Spare wheel in a retractable basket under the rear overhang - 01565 Fuel tank: 85 l - 02210 Spare wheel - 05925 Additional adjustable fixed speed limiters - 06520 12V electric trailer sockets, 13-pin DIN - 06767 Double rear doors opening 270 degrees - 07820 Ball hitch for trailer - 08623 Reinforced rear parabolic springs with minor deflection for S models - 08650 Third brake light, illumination - 79336 Daily dummy chrome radiator grille with belt - 01553 Gunmetal emblems - 02443 Leather steering wheel - 02308 Daily alloy wheels - 72625 Full LED lighting Hsdpjym I D Nsfx Ahajt COMFORT PLUS PACKAGE - 00259 Swivel Comfort Seat (3-position adjustment, lumbar support, armrest) - 01611 USB A+C ports for driver and co-driver - 75082 2-seater passenger bench with folding table, 3-point seatbelt - 07196 170 cm3 air conditioning compressor - 01605 MY IVECO NAVI infotainment system with 10-inch display - 06555 Fog lights - 14522 Adaptive Cruise Control (ACC) with radar sensor - 06650 Cab ventilation and heating system with automatic air conditioning - 79297 Fully upholstered headrests with memory foam, Daily logo In-stock vehicle, immediately available Our special services for you: * Full service history at authorized partners and certified workshops * Winter tires available for an additional charge * Extended warranty up to 36 months available at extra cost * Fair trade-in offer for your used vehicle * Financing from 6.99% with or without down payment, up to 96 months (subject to credit approval) * TÜV / DEKRA major and emissions inspection * EU net sales possible - intra-community supply with valid VAT ID * Non-EU (worldwide) sales possible including export declaration, supplier’s declaration * Nationwide delivery available for an additional charge * Registration service for export and temporary license plates, incl. insurance and registration fees All details provided on the internet are non-binding descriptions. Errors and mistakes reserved. The information provided does not constitute a guaranteed feature in the sense of § 434 para. 1 sentence 3 BGB (German Civil Code).

Condition: like new (used), Year of construction: 2015, functionality: fully functional, machine/vehicle number: 201502530269, measuring range X-axis: 700 mm, measuring range Y-axis: 700 mm, measuring range Z-axis: 600 mm, table load: 560 kg, Equipment: documentation/manual, type plate available, ZEISS CONTURA G2 7/7/6 – VAST XXT TL1 Year of Manufacture: 2015 | Commissioned: 2016 | Immaculate Condition | Extremely Low Operating Hours We are offering for sale a ZEISS Contura G2 coordinate measuring machine (CMM) with a measuring range of 700 × 700 × 600 mm, equipped with a VAST XXT TL1 scanning probe head. The device comes from a controlled laboratory environment and was used exclusively on-demand, single-shift operation, never on a production line – resulting in exceptionally low actual usage and outstanding technical condition. 🔹 Basic Information Manufacturer: ZEISS Model: Contura G2 Measuring Range (X/Y/Z): 700 / 700 / 600 mm Year of Manufacture: 2015 Commissioned: 2016 Technical and Visual Condition: Perfect Measurement Error MPE (E0) = 1.7+L / 350 μm 🔹 Configuration and Accessories ✅ ZEISS VAST XXT TL1 active scanning probe head ✅ Stylus rack / magazine ✅ Set of measuring styli (mainly diameters ⌀ 0.6 mm and ⌀ 1.5 mm) ✅ Reference sphere ✅ BP26_SE control console 🔹 Usage History Hodsyzmbdspfx Ahajt Device used exclusively in laboratory conditions Occasional, project-based (on-demand) use Single-shift operation, no serial or production work As a result, the machine exhibits extremely minimal mechanical wear 🔹 Service and Calibration ✅ Service and calibration exclusively by official ZEISS technicians ✅ Regular maintenance according to manufacturer guidelines ✅ No third-party interventions ✅ Device fully operational 🔹 Status 📍 Machine available immediately 🔍 Viewing possible 📄 Full documentation included ✅ Buyer arranges transport

Condition: used, maximum load weight: 29,441 kg, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 05/2023, next inspection (TÜV): 05/2024, total width: 2,550 mm, total height: 4,000 mm, Equipment: ABS, * Fifth wheel height 1120 * Side loading height with lifting roof and interior height 2750 2655 mm * Side loading height without lifting roof and interior height 2750 2610 mm Hsdorvu Nzspfx Ahaot * Total length 13830 mm * Platform interior length 13620 mm * Total width 2550 mm * Platform interior width 2480 mm * Interior width between stanchions 2480 mm * Interior width between longitudinal members (without lifting roof) 2480 mm * Interior width between longitudinal members (with lifting roof) 2430 mm * Neck height 105 mm * Axle spacing 1310 mm * Axle spacing kingpin 1st axle 6390 mm * Technically permissible total weight 42000 kg * Technically permissible axle load 9000 kg * Technically permissible fifth wheel load 15000 kg * External height 3975 mm * Empty weight 6559 kg * Railway code certificate P386 Chassis Steel lamp holder 19 pairs of lashing rings Floor made of screen-printed plate 30 mm Load capacity 7.5 tonnes + steel checker plate at the rear approx. 270 mm deep Rollers Ram buffer at the rear (WIELTON) Pallet stop with lashing holes Steel rear underrun protection Composite - side impact protection Liftable rear underrun protection Axles and suspension Number of axles 3 Rigid axles SAF disc axles 3x9000 kg 22.5 INTRADISC KNORR clamps Brake discs diameter 430 mm Fifth wheel height 1120 Hubodometer Support legs SAF Hercules 2-speed gearbox supports, full load Rims 6x steel rims 22.5-11.75 ET-120 Protective caps for wheel nuts Tires 6x tires 385-65-22.5 Other chassis equipment TIR sign, foldable Tensioning belt with ratchet 7 tons - 8 pieces Fire extinguisher 6 kg Ship fastening straps 4 pairs Two wedges with fastening A-sign, foldable ADR sign, foldable Fire extinguisher box on the front wall Tool box - 165L Railway coding number P 386 F1 Side loading height i.L.: 2,530 mm F2 Internal height i.L. under roof: 2,575 mm Construction Lifting roof (0, +50) Top slats - 7 rows Side tarpaulins with eyelets (at least 24 tarpaulin tensioners) Tarpaulin tensioning device at the front secured with a flap and customs rope (TIR version) Tarpaulin tensioning device at the rear Tarpaulin tensioner with additional lock Customs version on the outer frame with safety lock Sliding roof on one side from back to front EDSCHA HYBRID (TIR version) Aluminum bulkhead with customs eyelets Rear wall as aluminum double-wing door Screen-printed plate 6 mm H=1500 mm 2x transparent tarpaulin pockets for ADR labels Painting of other equipment 2-sided painting (powder coating) bulkhead, doors, corner stanchions Additional painting - color RAL5002 (ultramarine blue) Electrics 2x7-pin + 1x15 pole with EBS connection, without connecting cables to the tractor unit Lighting Hella LED EASYCONN version Rail / Intermodal equipment consisting of Axles with extended air bellows and adaptation of piggyback frame with gripper edges in accordance with Bach specifications Railway coding number P 386 Roller ram buffers at the rear, right and left RoRo Ferry Lashings Intermodal 5-fold ILU code, attached to the tarpaulins on the left and right, on the front wall, on the rear wall and on the roof Positions marked in yellow on the side in the area of the gripper edges (Rail) Side tarpaulins with 24 tarpaulin tensioners in accordance with railway specifications (Complies with the DAIMLER load securing guideline DL 9.5) Roof tarpaulin in accordance with railway specifications All information without guarantee. Errors subject to change. Subject to prior sale.

Condition: used, maximum load weight: 27,500 kg, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 06/2023, next inspection (TÜV): 06/2025, loading space volume: 100 m³, Year of construction: 2023, Equipment: ABS, bioSTAR approx. 100 cbm, 14.9 m internal length silver grey BIOSTAR - STEERABLE AXLE - V14900 - VERTICAL FRONT WALL - VERTICAL REAR DOOR Internal body length: approx. 14,900 mm Internal body width: 2,475 mm Body volume: approx. 90 cbm Gross vehicle weight (GVW): 36 t Axle spacing: 1,310 mm Unladen weight: 8,500 kg King pin height: 1,150 mm TECHNICAL DESCRIPTION 1. CHASSIS KING PIN HEIGHT: Precise king pin height is 1,150 mm. AXLES Tridem: Manufacturer: SAF - CUSTOM DESIGN (CD) Capacity: 3 x 9 t Suspension: Original SAF air suspension Brakes: Large disc Wheel offset: ET 120 Brake wear indicators (BVA) included The first axle is a self-lifting axle controlled via the EBS-E system. The third axle is a trailing steering axle. CONNECTIONS BRAKE WEAR INDICATOR (BVA): Brake wear indicators are connected. LIFT AXLE FUNCTION: Without lift axle. Including traction aid. TRACTION AID: The traction aid is activated by pressing a button in the truck (button in truck not included). AIR SUSPENSION: Lifting and lowering function. Aluminum air tanks. STEERABLE TRAILING AXLE LOCKING: Locking of the steerable trailing axle is managed as follows: - via reverse lights - by button in truck (button in truck not included) TYRES: 6 x 385/65 R 22.5 tyres for regional haulage (manufacturer's choice) on ALCOA MATT aluminum rims, ET 120. BRAKING SYSTEM - EBS: EBS-E system WABCO 2S/2M - PREMIUM MODULATOR Dual-line compressed air braking system in accordance with CE guidelines. Spring-loaded parking brake operating on 2 axles. With SMARTBOARD. R.S.S. (Roll Stability System) LIGHTING - ASPÖCK: 24 Volt electrical equipment. 2 x 7-pin + 1 x 15-pin ISO sockets. Aspöck kit. Orange LED lighting mounted on the trailer side. Without junction box at rear - NORDIC. REAR LIGHTING IN UNDER-RUN PROTECTION: Lighting is installed in the fixed aluminum underrun protection. With foldable aluminum lighting cover. 2 x 1 five-chamber lamp - EUROPOINT III - LED version. HYDRAULICS POSITION: Connection at the front wall. With additional connection option below the body in front of support legs. Hedsxplxzepfx Ahajt ACCESSORIES EXTENDIBLE LADDER AT REAR: Extendible ladder integrated at rear of vehicle, right side. PNEUMATIC CENTRAL LOCKING: With pneumatic central locking. TOOLBOX: PVC toolbox with key (800 x 460 x 430 mm) SPARE WHEEL HOLDER: Single aluminum spare wheel holder. 2. BODY FRONT WALL: The front wall is made of heavy-duty aluminum plank profiles. INTERNAL SEALING BETWEEN FLOOR AND FRONT WALL: Fixed sealing between floor and front wall using aluminum profile and PVC gasket. SIDE WALLS: Inner and outer surfaces smooth. Double-walled side wall profiles, 600 mm wide - 30 mm thick - 3 mm inside - 2 mm outside (grain specification). Side wall profiles are fully welded on the inside. WEAR PLATE: Aluminum wear plate, rectangular, inside rear, 2000 (L) x 1500 (H) x 4 mm. MOVING FLOOR SYSTEM: CARGO FLOOR CF 500 SL-C, electric control. 21-board floor system. Drive unit consists of 3 double-acting hydraulic cylinders with 200 mm stroke. Rear end plate in stainless steel. FLOOR SYSTEM OPERATION: Electric control with radio remote (genuine Cargo Floor). Loading - stop - unloading via switch. Manual emergency operation using unique red Cargo rotary knob. MOVING FLOOR FRAME: Frame for wheelbase 7,850 mm. 21 floor boards. FLOOR BOARDS: 21 aluminum floor boards - 8 mm ribbed, with welded aluminum end caps. REAR DOOR: 2 portal h

Condition: refurbished (used), Year of construction: 2019, operating hours: 8,440 h, load capacity: 1,600 kg, lifting height: 5,000 mm, load center: 500 mm, fuel type: electric, mast type: triplex, construction height: 2,235 mm, battery voltage: 48 V, fork length: 1,200 mm, empty load weight: 2,471 kg, Equipment: cabin, FRIEDMANN FORKLIFTS – PROFESSIONALLY REFURBISHED BY EXPERTS. FOR PROFESSIONALS IN ACTION Our forklifts are technically overhauled according to FEM-4.004 guidelines and current safety standards – ensuring maximum quality and safety. Every vehicle is thoroughly inspected and reconditioned, from the chassis to the battery, including drive system, brakes, steering, and electrics. ? Made in Germany – with responsibility and precision ? Strict technical inspection ? 400+ units available ? Worldwide shipping & customs clearance ? Service & spare parts at fair prices ? Personal support – even after purchase Test and get advice on-site – we'll find the right solution for you. Industrial Truck Specifications: Manufacturer: Jungheinrich Type: Counterbalance Forklift EFG 216k Drive type: Electric Load capacity: 1,600 kg Year of manufacture: 2019 Operating hours: 8,440 Lift height: 5,000 mm Mast type: Triplex Free lift: Yes Overall height: 2,235 mm Fork length: 1,200 mm Unladen weight: 2,471 kg Hodoy Rq Dhepfx Ahast Load center distance: 500 mm Tyres: Solid rubber Model designation: EFG 216k Battery type: Lithium-ion Voltage: 48 V Battery weight: 924 kg Cab type: Front & roof window Cab equipment: SoloPilot control lever Lighting: Work lights 2x front Lighting: Revolving warning beacon Attachment: Sideshifter

Condition: new, Year of construction: 2025, load capacity: 2,500 kg, lifting height: 4,700 mm, fuel type: gas, mast type: triplex, construction height: 2,160 mm, fork length: 1,200 mm, empty load weight: 3,740 kg, FRIEDMANN FORKLIFTS – REFURBISHED BY EXPERTS. FOR PROFESSIONAL OPERATORS. Our forklifts are expertly refurbished to FEM-4.004 guidelines and current safety standards – delivering maximum quality and safety. From chassis to battery, including drive system, brakes, steering, and electrics – each vehicle is thoroughly inspected and overhauled. Hodpfx Ahsy Rqpksajt ✔ Made in Germany – with responsibility and precision ✔ Rigorous technical inspection ✔ 400+ machines available ✔ Worldwide shipping & customs clearance ✔ Service & spare parts at fair prices ✔ Personal support – even after your purchase Test on site and get expert advice – we’ll find the right solution for you. Industrial Truck Data: Manufacturer: Heli Model: Counterbalance Forklift CPYD25-G3-KU Drive type: LPG Load capacity: 2,500 kg Year of manufacture: 2025 Operating hours: 0 Lift height: 4,700 mm Mast type: Triplex Full free lift: Yes Overall height: 2,160 mm Fork length: 1,200 mm Unladen weight: 3,740 kg Tyres: Solid rubber Model variant: CPYD25-G3-KU Lighting: 2x front work lights Lighting: 1x rear work light Lighting: Rotating beacon Lighting: Road package – equipped for potential use on public (restricted) roads: indicator, rear light, reversing light, reflector, etc. Attachment: Sideshift Attachment: Additional hydraulic circuit (routed to carriage)

Condition: new, Year of construction: 2025, load capacity: 7,000 kg, lifting height: 4,000 mm, fuel type: diesel, mast type: duplex, construction height: 3,030 mm, fork length: 1,800 mm, empty load weight: 9,600 kg, Equipment: cabin, FRIEDMANN FORKLIFTS – OVERHAULED BY EXPERTS. FOR PROFESSIONALS AT WORK. Our forklifts are fully reconditioned to FEM-4.004 guidelines and the latest safety standards – for maximum quality and your safety. From chassis to battery, including drive, brakes, steering, and electrics – every machine is thoroughly inspected and refurbished. ✔ Made in Germany – with responsibility and precision ✔ Rigorous technical inspection ✔ 400+ units available ✔ Worldwide shipping & customs clearance ✔ Service & spare parts at fair prices ✔ Personal support – even after purchase Test and get advice on-site now – we’ll find the right solution for your needs. Industrial Truck Specifications: Manufacturer: Heli Model: Counterbalance Forklift CPCD70-G3-YC Drive type: Diesel Load capacity: 7,000 kg Year of manufacture: 2025 Operating hours: 0 Lift height: 4,000 mm Mast type: Duplex Free lift: No Overall height: 3,030 mm Fork length: 1,800 mm Unladen weight: 9,600 kg Tyres: Solid rubber Model designation: CPCD70-G3-YC Hedoy Rqkhopfx Ahaot Cab type: Full cab – front, roof & rear windows + steel doors (suspended) Lighting: 2x front work lamps Lighting: 1x rear work lamp Lighting: Rotating beacon Lighting: StVZO – equipment for potential use on (limited) public roads: indicator, tail light, reversing light, reflector, etc. Attachment: Side shifter Attachment: Fork positioner Attachment: Additional hydraulic circuit – fitted up to fork carriage