Used Schubert Roller Leveller for sale (14,265)

Condition: used, Year of construction: 2022, Maximum parent roll width: 1420 mm Minimum parent roll width: 600 mm Maximum parent roll diameter: 1500 mm Maximum parent roll weight: 2500 kg Maximum unwinding tension (Ø1500 mm): 600 N Minimum unwinding tension (Ø1000 mm): 40 N Minimum standard slitting width: 100 mm Maximum rewinding width: 1400 mm Maximum rewinding diameter: 1050 mm Maximum rewinding weight: • Ø76 mm shaft: 600 kg • Ø152 mm shaft: 1000 kg Maximum rewinding tension: 600 N Maximum production speed: 600 m/min Power supply: 3 x 400V 50Hz Installed power: 30 kW Compressed air: 6 bar, dry Materials to be slit: • Paper-based / liner-based packaging laminates. • Board from 80 to 300 g/m². Unwind section: A separate between-centers unwinder, type T9, 1500 mm diameter, including: • Hydraulic cylinder control for lifting parent rolls from the floor. • Two motors driving the unwinding roll, controlled by an ultrasonic diameter sensor and a tension-control dancer roller. • Two pneumatic expanding adapters, SVECOM, for 70/76 mm (3”) cores. • Two pneumatic expanding adapters, SVECOM, for 150/152 mm (6”) cores (mounted on the pneumatic end adapters). • Floating edge-correction roller. • Automatic web guiding system, FIFE DP20, with SE26A photoelectric sensor, ±100 mm correction via electric actuator — for controlling sheet edge or continuous printed line. • Connecting walkway allowing web threading at floor level while keeping full access to the slitting station. • All web path rollers are anodized. • Safety guarding for operator protection. Slitting section: A slitting station with individual pneumatic knives and circular counter-knives: • Shear cut performed against the counter-knives. • Counter-knife shaft driven by an independent motor; counter-knife shaft is pneumatic. • Pneumatic knife holders mounted on a beam with a dovetail guide (TIDLAND) and an air supply manifold for individual activation. • 10 slitting sets, each including: Individual TIDLAND pneumatic knife holder (25 mm width) and double-bevel circular knife Ø 90/60 mm. • Set of multi-groove counter-knife rings, 5 mm pitch, 50 mm length. Web separation section: • A separator roller driven by the slitting motor; angle and curvature fully adjustable. Lay-on roller: • Lay-on roller made of anodized ground aluminum or polyurethane (depending on materials). • Pressure is adjustable and synchronized with winding diameter. • Roller is removable. Automatic splicing / transverse cutting system: Gsdpfx Aajyx Uy Aoysbt • Hydraulically operated pivoting arm including a transverse knife with linear motion and a backing plate for securing the web onto new cores. Trim extraction system: • Trim suction unit with two width-adjustable nozzles. • Turbine enclosed in a sound-insulated cabinet, conveying trim to a centralized system or container (not included). Rewinding section: • Motorized turret (two-position) supporting two rewinding shafts. • Rewinding shaft drive by an oversized asynchronous motor. • Hydraulic centering point for the active rewinding roll. • Two pneumatic expanding shafts Ø76 mm (3”), max load 600 kg each, equipped with full-width rubber strips with individual bladders. • Two pneumatic expanding shafts Ø152 mm (6”), max load 1000 kg each, also equipped with full-width rubber strips with individual bladders.

Condition: ready for operation (used), Year of construction: 2018, spindle speed (max.): 4,000 rpm, travel distance X-axis: 150 mm, travel distance Z-axis: 500 mm, spindle motor power: 4,000 W, total height: 1,700 mm, total width: 890 mm, overall weight: 1,050 kg, bar diameter (max.): 43 mm, product length (max.): 1,570 mm, workpiece diameter (max.): 280 mm, number of slots in tool magazine: 4, number of axes: 2, Horizontal turning machine manufactured in 2018. This Weiler PRIMUS VCD features a connected load of 7.5 kVA and operates at a nominal current of 15.5 A. With a machine weight of 1050 kg, it is designed for robust performance. If you are looking to get high-quality turning capabilities, consider the Weiler PRIMUS VCD machine we have for sale. Contact us for further details. • Machine Type: Centre Lathe • Turning Length / Distance Between Centres: 500 mm • Swing Over Bed: 280 mm • Swing Over Cross Slide: 150 mm • Spindle Nose (DIN 55027): Size 5 • Front Bearing Diameter: 70 mm • Spindle Bore: 43 mm • Main Spindle Internal Taper: ME 50 • Drive Power (100% Duty Cycle): 4 kW • Spindle Speed Range: 30 – 4,000 rpm • Number of Feed Rates: 24 • Longitudinal Feed Range: 0.02 – 0.63 mm/rev • Cross Feed Range: 0.006 – 0.20 mm/rev • Metric Thread Range: 0.25 – 8 mm • Inch Thread Range: 80 – 2 TPI • Module Thread Range: 0.25 – 4 Module • Diametral Pitch (DP) Thread Range: 200 – 5 DP • Tailstock Quill Diameter: 40 mm • Tailstock Quill Travel: 85 mm • Tailstock Taper: MT3 • Operating Voltage: 400 V • Control Voltage: DC 24 V • Connected Load: 7.5 kVA • Nominal Current: 15.5 A Gbjdpezpwh Usfx Aayot • Frequency: 50 Hz • Main Fuses: 25 A • Machine Weight: 1,050 kg • Machine Dimensions (L × W × H): 1,570 × 890 × 1,700 mm Additional Equipment • 4-Position Quick-Change Tool Post PARAT Size 1, incl. 1 × WD 1/12 Tool Holder • 2 × WD 1/12 Tool Holders • Lever-Operated Collet Chuck for 173 E Collets • 13 × 173 E Collets, Clamping Range: 3–15 mm (1 mm Increments) • Fixed Steady Rest with Roller Jaws, Capacity: 15–100 mm • Movable Chip Splash Guard with Viewing Window • 8 × Levelling Elements Technical Specification Counter Spindle No Driven Tools No

Condition: new, Year of construction: 2026, machine/vehicle number: CF 10 T / 1, Our CF 10T bottom flap folder with filling station is an inexpensive entry-level model. Cardboard boxes with a length of 200 to 600 mm and a width of 150 to 480 mm are fixed for filling and pneumatically transferred to the next station. This simple model comes with a magazine and runs on normal household electricity. The CF 10T requires compressed air for operation. Technical data: Dimensions 1400 x 950 x 700-860 mm Weight 90 kg Operating voltage 230 V / 600 W Compressed air 6 kgf/m3 Working height 700 - 800 mm Noise emission < 75 dB(A) Gjdpfx Aezr Hk Djayebt Cardboard formats: Length 200 to 600 mm Width 150 to 480 mm Height 120 to 500 mm Roller conveyor is not included in the price, but can be purchased as an option. Can also be combined with one of our carton sealers on request.

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, machine/vehicle number: 99.125.681, working width: 1,100 mm, overall weight: 2,500 kg, grinding belt length: 1,890 mm, grinding belt width: 1,110 mm, Equipment: CE marking, TECHNICAL DETAILS Number of units: 2 Unit 1 Position: Top Unit type: Contact roller Sanding belt length: 1,890 mm Sanding belt width: 1,110 mm Roller diameter: 175 mm Roller material: Rubber Motor power: 18.5 kW Gbodpfx Aezxcmzoayst Unit 2 Position: Top Unit type: Contact roller Sanding belt length: 1,890 mm Sanding belt width: 1,110 mm Roller diameter: 175 mm Roller material: Rubber Motor power: 18.5 kW Max. working width: 1,100 mm Min. working height: 30 mm Max. working height: 183 mm Infeed table length: 400 mm Outfeed table length: 250 mm MACHINE DETAILS Feed motor power: 0.75 kW Voltage: 380 V Current consumption: 36 A Fusing: 63 A Dimensions & Weight Dimensions (L x W x H): 1,700 x 1,800 x 2,320 mm Unladen weight: 2,500 kg Number of transport packages: 1 EQUIPMENT CE marking

Condition: used, Year of construction: 2024, Air brake Slope disk Following harrow Lighting with track eradicator / telescopic drawbar CAT III / IV Hydraulic track eradicator HM hydraulic / front level board Coulter set Carbide goose foot coulter Hydr. system FW with roller / DSTS roller / Gjdpetpgtlofx Aayebt

Condition: ready for operation (used), Year of construction: 2021, operating hours: 15,000 h, functionality: fully functional, Equipment: documentation/manual, 2021 Star SR32 JII Type A (15,000 hours) 4m FMB Turbo 3-36, Hydrajet UB20 High Pressure Coolant, LNS Swarf Conveyor, FireTrace Suppression, JBS Guide Bush System, Fully inspected & serviced, 30 Day Warranty # Star SR-32JII CNC Sliding Head Lathe Machine Hours: Approx. 15,000 hours Maximum Machining Diameter: Ø32 mm standard / Ø34 mm optional CNC Control: Fanuc 32i-B ## Machine Configuration * Twin-spindle CNC sliding head lathe * Main spindle and sub-spindle * Main and sub-spindle full C-axis control * Gang-type tooling system * Cross-working driven tooling * Back-working tooling * X1, Y1, Z1, C1, X2, Z2 and C2 controlled axes * Type B configuration additionally incorporates Y2 control on the back-working unit ## Main Spindle * Maximum spindle speed: 8,000 rpm * Spindle motor: 7.5 kW continuous / 11 kW short-time rating * Maximum headstock stroke: 320 mm * Full C-axis contouring capability ## Sub-Spindle * Maximum spindle speed: 8,000 rpm * Spindle motor: 3.7 kW continuous / 5.5 kW short-time rating * Full C-axis contouring capability * Maximum chucking diameter: Ø32 mm / Ø34 mm optional ## Main Tooling * 6 × turning tool positions * Tool size: 16 mm square * 5-spindle sleeve holder * Maximum drilling capacity: Ø13 mm * Maximum tapping capacity: M12 × P1.75 ## Cross-Working / Driven Tooling Configuration options include: * 3 × ER20 cross-milling positions + 2 cartridge-type positions Gbedszuxfrepfx Aayet * Or 6 × ER16 cross-milling positions * Maximum milling capacity: Ø10 mm * Maximum driven tapping capacity: M8 × P1.25 * Cross-milling spindle speed: 6,000 rpm * Cartridge-type driven tooling speed: up to 8,000 rpm * Driven-tool motor: 2.2 kW continuous / 3.0 kW short-time rating ## Back-Working * Maximum chucking diameter: Ø32 mm / Ø34 mm optional * Maximum front ejection length: 125 mm * Maximum projecting component length: 45 mm * Back-working tool positions: * 6 positions – Type A * 8 positions – Type B * Stationary drilling capacity: Ø13 mm * Driven drilling capacity: Ø8 mm * Stationary tapping capacity: M10 × P1.5 * Driven tapping capacity: M6 × P1.0 * Maximum back-working driven-tool speed: 6,000 rpm ## Rapid Traverse * X1 / X2 / Y1 / Z1 / Z2: 35 m/min * Y2: 24 m/min on applicable Type B machines ## Ancillary Equipment Included * 4 metre FMB Turbo 3-36 Magazine Bar Feeder * Hydrajet UB20 High-Pressure Coolant System * LNS Swarf Conveyor * FireTrace Automatic Fire Suppression System * JBS Guide Bush System ## Machine Condition & Support * Approx. 15,000 operating hours * Fully inspected and serviced * Supplied ready for production * 30 Day Warranty * Warranty valid within the UK only ## General Specification * Coolant tank capacity: 255 litres * Approximate machine dimensions: 2,690 × 1,345 × 1,780 mm * Approximate machine weight: 4,100 kg * Power requirement: 8.8 kVA * Maximum sound pressure level: 77 dB

Condition: excellent (used), Panel Saw HOLZ-HER 1255 -used- Welded frame with extremely high rigidity, pneumatically retracting shifting grid, stable latching of the saw carriage at both top and bottom, latch monitoring in vertical cut electrically controlled, foldable plunge lever on the saw unit, retractable riving knife for cut-outs, operator panel at eye level, digital display on the longitudinal fence, digital display for horizontal cut, strip cutting device, roller lift transport system, trim-capable support surface, dust extraction device TRK, dust-tested. ----- Technical Data ----- Cutting length: 5200 mm, Cutting height: 2200 mm, Trimming height: 2100 mm, Cutting depth: 60 mm, Minimum height on folding rail: 120 mm, Saw blade Ø: 250 mm, Motor: 4 kW, Extraction port Ø: 120/100 mm, Compressed air: 6 bar, Gbsdpfeyyzp Hex Aayet Required space (LxWxH): 6500x1650x3050 mm, Weight: 900 kg Quality Information: - Fence strips replaced / refurbished - Comprehensive basic inspection - Complete basic cleaning - Electrical system checked - Immediately operational

Year of construction: 2021, condition: used, Multi-blade saw CAN CUT MC 930 Year of manufacture: 2021 Technical specifications Cutting width: 1,100 mm Max. cutting height: 50 mm Min. workpiece length: 650 mm Feed rate: 5-20 m/min Feed motor: 0.75 kW, 1,410 rpm Max. power consumption: 22 kW, 380 V Motor power: 30 hp Max. saw blade diameter: 250 mm Saw arbor diameter: 70 mm Saw blade speed: 3,500 rpm Max. number of saw blades: 15 pieces Working height: 900 mm Sound pressure level: 80 dB Automatic transport rollers: 3 pieces Rubber rollers between the saw blades to reduce vibrations when cutting MDF boards and wood. Gbodpfxozu St Ae Aayst

Condition: reconditioned (used), Number of spindles 5 St. Working width 230 mm Working height 120 mm Length of the planing table 2500 mm Feed motor 4 kW Feed speed 5-30 m/min. Control Memory-Funktion Weinig Powermat 400 with HSK/Powerlock, axial/radial CNC controlled ----- This machine is currently being refurbished at our facility! Pictures taken before dismantling and currently during the processing phase! Brief Summary: ----- - 5 spindles with 8,000 rpm - 4 x HSK/Powerlock - Axially and radial CNC adjustments of the spindles via control - CNC-controlled adjustment and positioning of the feed - Table tops with guide blades at spindles 2 and 3. - Includes Weinig/Neumann RF 15 return conveyor system Detailed Description: ----- Technical Data: Working width: 20-230 mm Working height: 8-120 mm 1st tool holder - bottom ----- Motor with brake: 5.5 kW Gsdpfx Aasyy A Iqsysbt Spindle diameter: 40 mm Speed: 6,000 rpm Tool swing diameter: 93 - 145 mm Axially travel: 5 mm Folding device MarathonCoatin for table insert in front of 1st lower Tool Holder 2nd Tool Holder - PowerLock - Right ----- Motor with brake: 7.5 kW Shared motor with left tool holder Speed ??incl. high-performance ball bearings: 8,000 rpm Tool swing diameter 40 mm below table level: 93 - 200 mm Tool swing diameter 55 mm below table level: 93 - 180 mm Tool swing diameter for straight cutter heads max. 163 mm Max. tool diameter behind stop plane: 180 mm Max. groove depth: 35 mm Axially travel: 55 mm Spindle: CNC controlled axially Table tops with guide blades 3rd Tool Holder - PowerLock - Left ----- Motor with brake: Shared motor with the 2nd spindle Speed ??incl. high-performance ball bearings: 8,000 rpm Tool swing diameter 40 mm below table level: 93 - 180 mm Table surface: 93 - 200 mm Tool swing diameter 55 mm below table surface: 93 - 180 mm Tool swing diameter for straight cutter heads max. 163 mm Max. groove depth: 35 mm Axially travel: 55 mm Spindle axially and radially CNC controlled Table tops with guide blades 4. Tool holder - PowerLock - top ----- Motor with brake: 7.5 kW Speed ??incl. high-performance ball bearings: 8,000 rpm Tool swing diameter: 93 - 200 mm Tool swing diameter for straight cutter heads max.: 180 mm Max. groove depth: 35 mm Axially travel: 40 mm Split pressure shoe in front of upper tool holder, adjustable and pivoting away from the tool, spring-loaded. Pressure shoe in front of, and discharge after, the upper tool holder with electronic digital displays, integrated into memory functions CNC-controlled radial spindle 5. Tool holder - PowerLock - bottom ----- Motor with brake: 7.5 kW Speed ??incl. high-performance ball bearings: 8,000 rpm Tool swing diameter: 93 - 200 mm Max. throat depth: 15 mm Axially travel: 35 mm Feed system ----- Frequency-controlled feed, infinitely variable with brake: 4 kW, 5 - 30 m/min Infeed roller in front of the first lower tool, pneumatically controlled up/down. Durofer pointed tooth rollers (Weinig patent) wi...

Condition: used, Year of construction: 2014, functionality: fully functional, MiniBendCenter RAS 79.05 Fully automatic panel bending center for small parts - General Information: Direct from manufacturer Manufacturer’s warranty Maintenance included Latest possible software version - General technical data (in mm): Blank length: 50–600 Blank width: 40–600 Sheet thickness max. (400 N/mm²), tool-dependent: 3.0 Upper beam stroke max.: 500 mm Minimum flange height (reference value, tool-dependent): 5 × s Max. flange height: 127 Weight of bending cell: 10 tons Weight of enclosure and electrics: approx. 2,027 kg Weight of machine elements: approx. 945 kg - Machine-specific data: Motor operated; 400V, 50/60 Hz, 3-phase Year of manufacture: 2014 Condition: Refurbished – good used condition - Machine Configuration: Bending cell: - Automatic sheet thickness adjustment - Automatic tool clamping - Blank scanner Main manipulator: - 3 servo motors for X, Y, Z axes - 1 servo motor for lower rotary axis + separate drive for rotary axis - Double sheet detection Tool changer: - 3 servo motors for X, Y, Z axes - 1 pneumatic swivel drive for rotary axis - Tool gripper - Two-level tool magazine - Automatic tool clamping in tool magazine Enclosure: - Bending cell, front and rear Mobile operating panel: - 18" Touch & More control Intelligent loading robot Combined camera-scanner system Analysis software Transfer table, Sauerfeld (52x9 mm) suction row (7x20 mm) Pallet station: Gedpfsx Hyhujx Aaysbt - Roller conveyor and heavy-duty chain conveyor - 1 position for new pallets (parts to be processed) - 1 position for "pallet in process" - 2 positions for finished pallets (empty or with remaining parts) Curved transport conveyor with 6 connection stations Finished part output enclosure Complete tool set RAS CAM-Office software incl. SolidWorks license and 2-year maintenance contract - Sample images Sample video available on request -

Condition: new, Year of construction: 2026, functionality: fully functional, 1.86 m Roller Conveyor with Measuring Guide – Precision Roller Table for Cutting and Transporting Metal Materials The 1860 mm roller conveyor with an integrated measuring guide is an advanced solution for supporting material cutting and feeding in industrial settings. Thanks to its high load capacity, sturdy construction, and precise length measurement system, this conveyor is perfect for use with band saws, circular saws, and other metalworking machines. Seven steel rollers ensure smooth movement of workpieces of various shapes and sizes. Key Features Built-in measuring guide – precise length control without the need for additional tools 7 steel rollers (60 × 360 mm) – even weight distribution and smooth transport High load capacity of 900 kg – suitable for heavy pipes, profiles, bars, and shafts Adjustable height (650–1100 mm) – easy integration with different machines Modular extension capability – for building multi-segment roller tables Construction and Technology The CORMAK roller conveyor is made of deformation-resistant steel profiles. Stability is ensured by reinforced legs with crossbars. Each of the seven rollers is mounted on ball bearings, providing smooth and secure material guidance. The integrated measuring guide with a scale allows for quick length setting without the need for additional stops or measuring instruments. Precision and Work Efficiency The roller table with a measuring guide significantly shortens material preparation time by eliminating the need for manual measuring of each piece. Thanks to the precise measurement system, repeatable production can be carried out with high accuracy. Accurate material positioning improves cut quality, reduces material waste, and enhances workplace safety. Gjdpfx Asxp Iy Ujayobt Applications The 1.86 m roller conveyor with measuring guide is designed for production facilities, metalworking workshops, and companies involved in steel structure prefabrication. Especially recommended for: Precision cutting of pipes, bars, and steel profiles Operation with band saws and circular saws Feeding and receiving parts during batch processing Creating linear transport systems Standard Equipment 7 steel rollers with ball bearings Steel frame with cross reinforcements Height adjustment system (650–1100 mm) Integrated measuring guide Adjustable leveling feet Technical Specifications Roller diameter 60 mm Roller length 360 mm Number of rollers 7 Conveyor length 1860 mm Conveyor width 450 mm Height adjustment range 650–1100 mm Maximum load capacity 900 kg Weight 50 kg

Condition: like new (used), Year of construction: 2020, functionality: fully functional, tank capacity: 5,000 l, usable tank capacity: 5,000 l, total height: 3,225 mm, outer diameter: 1,756 mm, overall weight: 1,640 kg, wall material: stainless steel, wall thickness: 8 mm, wall structure: single-walled, manhole diameter: 610 mm, manhole location: top, operating temperature: 100 °C, negative pressure: 100,000 Pa, input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, Equipment: CE marking, sanitary facilities, Brand new, never commissioned. Professionally decommissioned from an INEOS manufacturing facility prior to first use. Manufactured by Able Engineering, this high-specification sanitary 316L stainless steel agitated pressure vessel is suitable for pharmaceutical, cosmetics, personal care, food, beverage and fine chemical applications. Designed for vacuum and low-pressure service and suitable for installation within ATEX-rated environments. Constructed entirely in 316L stainless steel throughout with 8mm shell and dish walls, dished top and bottom heads, heavy duty tubular stainless steel leg supports with bolt-down base plates and load cell arrangement, hygienic internal finish < 0.8 Ra, and full hygienic ferrule fittings throughout conforming to ASME BPE / BS3062. Suitable for CIP. Material: 316L Stainless Steel throughout. Working Volume: 5,000 Litres. Shell ID: 1,740mm. Overall Height: 3,225mm. Shell & Dish Wall Thickness: 8mm. Design Pressure: -1.0 to +0.45 Bar.G. Design Temperature: -10°C to +100°C. Empty Weight: 1,640kg. Design Code: PD5500:2018, Cat.3. PED 2014/68/EU certified. Manufacturer: Able Engineering. Serial Numbers: PXL19635-1, PXL19635-2, PXL19635-3. Factory Tested: September 2020. Fitted with SEW-Eurodrive geared agitator with double mechanical seal, seal pressure pot, and reinforced agitator mounting. Nozzles and fittings include 610mm hinged manway, CIP inlet with dip pipe and TOD clip-on spray fitting, pressure relief valve connection, nitrogen blanketing connection with pressure indicator, Endress & Hauser hygienic thermowell, dual flush polished level switches, load cell arrangement on support legs, lifting lugs, and earthing boss. Three units currently available, all brand new and never commissioned, sourced directly from the same INEOS facility. Tank saddles available on request for either single use or purchase. Please view our other listings for additional sizes and configurations — all stock is brand new, ex-INEOS, and available for immediate inspection and purchase. Gbsdpfxjzhnlzo Aayot Original engineering drawings and full nameplate documentation available on request. Inspection welcome by appointment. Loading and transport can be arranged. Tracht Ltd specialise in hygienic process equipment for the food, beverage, cosmetics, pharmaceutical and chemical industries, with practical experience supporting both batch and continuous manufacturing environments. In addition to process vessels, Tracht Ltd supply and install stainless steel mixing vessels, Silverson high-shear mixers, hygienic lobe pumps, hygienic centrifugal pumps, access gantries, and provide full vessel installation and commissioning services. Whether replacing existing equipment or expanding production capacity, Tracht Ltd can specify, supply and install the right equipment for your application. Please contact us for further information or to discuss delivery and installation options.

Condition: used, functionality: fully functional, power: 36.5 kW (49.63 HP), first registration: 10/2013, fuel type: diesel, fuel: diesel, operating hours: 3,574 h, Equipment: air conditioning, all wheel drive, car registration, differential lock, hydraulics, * 4-cylinder, 4-stroke diesel engine with 36.5 kW / 50 hp or 49.2 kW / 67 hp, water-cooled * 2,600 cc displacement * Permanent all-wheel drive via hydraulic wheel motors on each wheel Special paint finish RAL 9010 white Work package 1 Front lift including tow hitch CAT II / CAT I with passive tilt adjustment Rotating beacon Stabilizer bar Hydraulic set, flow divider 1 Flow divider, first circuit adjustable from 0–25 l/min with line set to the front and rear Return line to the front and rear Hydraulic set, flow divider 2 with tandem pump Flow divider, second circuit with tandem pump adjustable from 40–60 l/min line set to the front and rear return line to the front and rear leakage oil line to the front and rear Hydraulic tilting mechanism for superstructure frame Hydraulic set 1 consisting of: - 2 double-acting control valves with floating position - 4 quick couplings at the front - 2 quick couplings at the rear, connected via a T-piece with quick couplings at the front - Small joystick including floating position for front lift TIRE 31x10.5 R15 Overall outer width 120 cm, narrow, 140 cm wide when mounted Fender kit, narrow Multifunction joystick Flat roof Cabin mounted in the center Godpfxezd Rius Aayobt Hydr. tilting mechanism for cabin Holder flatbed, complete with substructure Internal dimensions approx. 1250 x 1060 x 400 mm Flow divider automatic Rotating beacon, LED Work light, LED Red/white warning markings The following winter attachments can be purchased separately: Roller spreader with hydraulic drive RA-C 06/42, 940 mm tipping flatbed, combined (NEW), for sand, gravel, possibly salt rear light design as on the vehicle paint RAL 2011 roller width: approx. 940 mm spreading width: approx. 1250 mm weight (empty): approx. 220 kg Spreading rate regulation adjustable via rotary knob in the cab proportional oil flow regulator, complete with cable and plug mounted on the spreader Semi-automatic, speed-dependent only applies in conjunction with item 2 deactivation of the roller when the vehicle stops Cable sets Control for spreader fill level Hummel front sweeper 145 cm working width hydraulic central drive – serial no. 980 Hummel MS-M1450HO front sweeper front lift CAT 1 central drive hydraulically via 3/4" chain dirt brush roller support feet 1 adjustable heavy-duty wheel in the center horizontal adjustment hydraulic pivoting hoses and couplings Subject to changes, printing errors, mistakes and prior sale. All information is provided without guarantee. The sale is made with the exclusion of any guarantee or warranty.

Condition: used, Year of construction: 2023, Köckerling Allrounder classic Hydraulic depth adjustment Herkulesz. Plus + / double spring Coulter set HM goose foot Single leveller STS roller Ø 530mm Lighting / Gbsdpfx Aet A Udmoayst

Condition: good (used), Year of construction: 2016, functionality: fully functional, Model: GL 840 PH H-UV Year: 2016 Impressions: 218 million PQC-S OFF-PRESS CONTROLS (with USB/CF media input) – including overhead amp HIGH SPEED START-UP SMART SEQUENCE SELF DIAGNOSIS II KHS-AI - Pre-linking & removal - Self-learning function - Production management system (diagnostics, maintenance) - Register preset SMART FEEDBACK SIMULTANEOUS PRESETTING OF FRONT/BACK INK KEYS (all units) AIR PRESET FULLY AUTOMATIC PLATE CHANGING – BENDERLESS TRANSFER CYLINDER COCKING REMOTE CONTROL PAPER THICKNESS PRESETS Gjdjy Rmdwepfx Aayebt PAPER SIZE PRESET PACKAGE • Sucker head preset • Slow-down wheel preset • Side lay guide • Delivery side jogger • Sheet release cam remote control FEEDER SIDE BLOWER PRESET FEEDER PILE SIDEWAYS CONTROL WITH PIT-LESS SKID LOADER SUCKER HEIGHT REMOTE CONTROL SUCTION TAPE FEEDER (Additional rubber wheels and belts on feeder board) ANTI-STATIC AT FEEDER SUCTION SIDELAY GUIDE FEEDBOARD VENTURI GUIDE ULTRASONIC DOUBLE SHEET DETECTOR REGISTER DETECTION (2-STEP DETECTION) ‘A’ TRANSFER CYLINDER GRIPPER PAD HEIGHT ADJUSTMENT ‘A’ (INFEED) CYLINDER COCKING REMOTE CONTROL ‘A’ (INFEED) CYLINDER ANTI-FANOUT REMOTE CONTROL ANTI-RUST TREATMENT FOR PLATE CYLINDERS ANTI-RUST TREATMENT FOR BLANKET CYLINDERS ANTI-RUST TREATMENT FOR IMPRESSION CYLINDERS ONE-TOUCH BLANKET CLAMP FOR BARRED BLANKET SHEET GUIDE OVER IMPRESSION CYLINDER AIR BLOWER ABOVE IMPRESSION CYLINDER SOLID TRANSFER CYLINDERS + GRIPPER PAD UP/DOWN (one-side adjustment) FULLY AUTOMATIC DOUBLE SIZE 3-CYLINDER PERFECTING UNIT IMPRESSION CYLINDERS WITH STAINLESS STEEL JACKET – after perfecting unit H-UV PROOF OIL SEALS INK DUCTOR INTERVAL ADJUSTMENT MOTORIZED INK FOUNTAIN ROLLER INK ROLLER NIP FOLLOWING INK ROLLER TEMPERATURE CONTROL (oscillation) INK OSCILLATION TIMING REMOTE CONTROL INKER FAN (feeder side on unit) INKER/DAMPENER DE-CLUTCH – all units INK MIST EXTRACTOR FANS (GL40) – New type KOMORIMATIC DAMPENING SYSTEM DAMPENING FORM ROLLER SPEED REDUCTION (Delta Effect) OSCILLATING RIDER ROLLER ON DAMPENING FORM ROLLER BRIDGE ROLLER RIDER ROLLER UNDER DAMPENING FORM ROLLER SKEWING DEVICE ON KOMORIMATIC WATER LEVEL SENSOR AUTOMATIC BLANKET CLEANER (H-UV/pre-pack) AUTOMATIC IMPRESSION CYLINDER CLEANING (H-UV/pre-pack) INK WASHING TRAY PNEUMATIC ON/OFF AUTOMATIC INK ROLLER CLEANING – twin nozzles SHEET DECURLER AIR BLOWER ABOVE DELIVERY PILE ANTI-STATIC BAR AT DELIVERY DELIVERY SHEET ANTI-DEVIATION DEVICE AUTOMATIC LUBRICATION ON DELIVERY CHAIN GUIDE DELIVERY AREA SENSOR DELIVERY PILE EXTRACTION – DRIVE SIDE FIXED ROLLERS – A, B & C INTERCOM H-UV DRYER PREPARATION Technotrans Beta.c 280G Alcosmart, digidos.p 150C, FZT 120P. Conductivity display for Beta.c pH value display for Beta.c • PDC-SX (Print Density Control – Spectrophotometer and Automatic Register Control) • KID (Komori Info-Service Display) • Baldwin Ozone-Free Metal Halide H-UV System, including: - 1x H-UV LED – end of press - 1x H-UV LED – before perfecting unit • Technotrans Beta.c 280G • Technotrans external cooling system (installation excluded) • A-APC – Asynchronous Automatic Plate Changing • A-APC / Automatic Blanket Cleaner Parallel Control for GL-40 • K-PressNavi • DC Blowers • Special Ink Misting Cover on All Units

Year of construction: 2026, condition: new, High precision sheet metal leveler system with servo-driven technology and customizable thickness and width configurations. Bosporas Machinery is a manufacturer of coil processing lines, roll forming lines and press feeding systems, delivering high-performance and customized industrial solutions worldwide. Our precision leveler machines are designed to eliminate internal stresses and ensure perfect flatness in sheet metal processing applications. Equipped with advanced servo motor technology, the system delivers synchronized, stable and repeatable leveling performance for demanding industrial operations. The machine is engineered as a high-performance solution combining precision leveling, material stability and continuous production efficiency in a compact and robust structure. The system is equipped with multiple precision straightening rollers supported by backup rollers, ensuring superior flatness correction and internal stress relief across the entire material width. This advanced structure enables consistent, high-accuracy leveling performance even in demanding applications. THICKNESS RANGE (FLEXIBLE CONFIGURATION) The system can be manufactured in different configurations depending on application requirements: 0.5 – 2.5 mm 0.4 – 8 mm 1.5 – 10 mm 2 – 15 mm 10 – 20 mm Custom production is available according to material type, thickness and project requirements. ENGINEERING & DESIGN High precision straightening performance Servo motor driven system for stable and accurate operation Advanced cassette-type structure for easy maintenance and fast adjustment Heavy-duty gear transmission system Bidirectional operation capability (left-right / right-left) PERFORMANCE High flatness accuracy Continuous and stable operation Reduced internal stress in material Optimized for industrial production environments SYSTEM COMPONENTS Precision leveler unit Cassette structure Gear transmission system Electrical and automation system Gbjdpfx Ajyzbmzjayet Entry / exit conveyor (optional) OPERATIONAL ADVANTAGES Excellent flatness and surface quality High repeatability and process stability Reduced downstream processing problems Flexible design for different industries Short lead time compared to European manufacturers APPLICATION AREAS Steel service centers Cut to length lines Coil processing lines Automotive and metal industries Sheet metal production OPTIONAL EQUIPMENT Entry / exit conveyor systems Automation and control upgrades Integration with coil processing lines (especially cut-to-length lines) Custom engineering solutions

Condition: like new (used), Year of construction: 2020, functionality: fully functional, tank capacity: 50,000 l, usable tank capacity: 30,000 l, total height: 4,275 mm, inner diameter: 4,000 mm, outer diameter: 4,020 mm, overall weight: 4,250 kg, wall material: stainless steel, wall thickness: 10 mm, operating temperature: 100 °C, Equipment: CE marking, sanitary facilities, Brand new, never commissioned. Professionally decommissioned from an INEOS manufacturing facility prior to first use. Manufactured by Able Engineering, this high-specification sanitary 316L stainless steel pressure vessel is suitable for pharmaceutical, cosmetics, personal care, food, beverage and fine chemical applications. Designed for vacuum and low-pressure service and suitable for installation within ATEX-rated environments. Constructed entirely in 316L stainless steel throughout with 10mm shell and dish walls, dished top and bottom heads, heavy duty tubular stainless steel leg supports with bolt-down base plates, hygienic internal finish < 0.8 Ra, and full hygienic ferrule fittings throughout conforming to ASME BPE / BS3062. Suitable for CIP, excellent condition. Material: 316L Stainless Steel throughout. Working Volume: 30,000 Litres. Shell ID: 4,000mm. Overall Height: 4,275mm. Shell & Dish Wall Thickness: 10mm. Design Pressure: -1.0 to +0.45 Bar.G. Design Temperature: -10°C to +100°C. Empty Weight: 4,250kg. Design Code: PD5500:2018, Cat.3. PED 2014/68/EU certified. Manufacturer: Able Engineering. Serial Number: PXL19785. Factory Tested: July 2021. Nozzles and fittings include 610mm hinged manway with grill, triple CIP sprayball arrangement, inlet connections, vent, pressure relief valve connection, Endress & Hauser hygienic thermowell, dual level switches, level measurement connection, lifting lugs, and earthing boss. Two units currently available, both brand new and never commissioned, sourced directly from the same INEOS facility. Tank saddles available on request for either single use or purchase. Please view our other listings for additional sizes and configurations — all stock is brand new, ex-INEOS, and available for immediate inspection and purchase. Gbsdpfxszhn Rqs Aayet Original engineering drawings and full nameplate documentation available on request. Inspection welcome by appointment. Loading and transport can be arranged. Tracht Ltd specialise in hygienic process equipment for the food, beverage, cosmetics, pharmaceutical and chemical industries, with practical experience supporting both batch and continuous manufacturing environments. In addition to process vessels, Tracht Ltd supply and install stainless steel mixing vessels, Silverson high-shear mixers, hygienic lobe pumps, hygienic centrifugal pumps, access gantries, and provide full vessel installation and commissioning services. Whether replacing existing equipment or expanding production capacity, Tracht Ltd can specify, supply and install the right equipment for your application. Please contact us for further information or to discuss delivery and installation options.

Condition: used, Year of construction: 2024, spiral disc suspension telescopic drawbar cat. III/IV hy hydraulic / front level board air brake DSTS roller lighting rear harrow DSTS roller / Gjdpett I N Ijfx Aayobt

Condition: used, Year of construction: 2013, operating hours: 4,867 h, functionality: fully functional, Equipment: Basic model DW 3060-C “Büffel” Central axle trailer chassis with 3 axles, road approval for 80 km/h Gedjzn Icyepfx Aaysbt Braking system incl. ABS and lighting according to EC directive 50 mm EC drawbar coupling incl. adapter shoe Hydraulically adjustable support legs Splash guard (fenders inside and on the side) Permissible total weight 25,000 kg Tires 385/65 R22.5 Mercedes-Benz diesel engine OM460LA, 315 kW at 2,000 rpm, meets exhaust emission standard EUROMOT IIIB Additional hydraulic connections 20 l and 70 l/min. (using a variable pump) Hydraulic preparation for comb basket system and drive mechanism Fuel tank 2 x 300 liters Roller length 3,000 mm, diameter 600 mm Trapezoidal teeth for roller (21 pieces) and comb (22 pieces) - form C (174 mm, armored) Rear belt: belt length 5,500 mm, belt width 1,200 mm, hydraulically foldable, with anti-magnetic center section Longitudinal belt: belt length 3,300 mm, belt width 1,000 mm Centrally arranged lubrication strips 24-V electrical control system Reversal of the roller by means of an electric motor when the engine is stopped Automatically reversible fan wheel Chassis with level adjustment Acoustic start-up warning Paint finish: 2-component paint RAL2011 deep orange Additional equipment: BioPower package - Engine output: 360 kW, with reinforced planetary gearbox - Multi-tooth roller, length: 3,000 mm, diameter: 600 mm - Roller teeth 174 form C armored (42 pieces) - Comb basket system with fine strip basket - Transmission oil cooler Hydraulic drive mechanism Radio remote control NEODYM over-belt magnet for rear belt Frame for over-belt magnet Humidification system Funnel attachment plates foldable on both sides Delivery date will be agreed upon.

Condition: used, machine/vehicle number: 8427, * Amazone Horse Hopper 1500 Smart Cut * Working width: 1.50 m * 1,500 L collection hopper capacity * Tractor 3-point linkage * H60 wing blades * Support rollers * Mulching device * PTO shaft with overrunning clutch * Collection hopper with hydraulic floor emptying * Rotation speed: 2,650 rpm * Fill level indicator -----Internal vehicle number: 8427 WhatsApp support available! If you have any questions about the machine or need further information, feel free to contact us conveniently via WhatsApp. Gbjdporhy H Rjfx Aayot Whatsapp Whatsapp ----Subject to errors and prior sale.

Condition: new, operating hours: 5 h, functionality: fully functional, control cabinet width: 800 mm, control cabinet height: 1,700 mm, input voltage: 400 V, input current: 16 A, type of input current: AC, Equipment: documentation/manual, Individual System L25-2203 cleanCABINET CL 100G-BRP Complete laser system for integration as individual components, consisting of the following modules: - Special item: Low-power laser production Laser system CL100G-BRP, diode-pumped laser Wavelength 1064nm, operating mode: pulsed (ns) Average laser power: P = 100 W +/- 3% Prepared for pilot laser, 19" rack-mount design Comparable to 2003836 Special configuration: 10m fiber length, extended pulses - 2D optics system Stamp 10 for LP lasers (CL12BRP-CL100BRP) Automated 2D optics with connection for back-reflection protection (BRP) and 90° deflection, max. working area: 120mmx120mm (=160mm)/290mmx290mm (F=420mm) Focus diameter depends on the focal length of the optics Included components: 2D optics system Stamp 10 90° connection Control electronics Cable set cleanSTUDIO/cleanCONTROL license for 2D optics (without axis system support) RTC - Focusing lens f=254, fully quartz, High grade, working area approx. 150mmx150mm Minimal focus shift - BG protective glass slide STAMP 10/14 F420 Quick-change slide for mounting on the Stamp14 with locking monitoring - Alignment laser for low-power lasers (LP) Gjdpfx Aaozl Slysyjbt (CL12G-CL-500G) The alignment laser allows monitoring the beam incident point on the component surface. Installation in the beam source, coupling into the fiber transmission, wavelength = 660nm, power: P = 0.5 mW (min. 0.2mW, max. 1.0 mW) - Decentralized laser source housing W/L Housing for the CL100 beam source including air-water heat exchanger 2kW, see 3D-CAD file. - GS control cabinet 1-1600 (CL12G-CL100G) Update: 32m cable length Laser housing in control cabinet design, type 1/1600 for low-power laser systems (CL12G-CL100G) consisting of: cabinet frame with Rittal double-bit lock, structural powder coating, RAL 7035S, optional air conditioning Installed on heavy-duty rollers, braked, 250kg load capacity, Fiber/cable feed-through through the roof, power supply via Harting Han6, left side panel, safety circuit "Performance Level D", installation position of laser and fiber outlet variable, emergency stop, key switch for starting and main switch in the front door, tested according to DGUVV3 Dimensions: HxWxD: 1600x600x800mm requires operation visualization, cooling capacity adjusted to the ambient temperature at the installation location WITHOUT AIR CONDITIONING as it is only for accommodating HMI, PC and PL-D technology including PLD technology PLD item as plug-in module (see below or alternatively wired in the control cabinet - BG housing 19" 2U PLD PLD plug-in for safe shutdown of low-power laser systems, installed in 19" housing - 2U for use with laser systems - VS-OPT Ethercat copper (MP/HP 2D) Ethercat interface for mid and high-power (2D) systems - fieldbus interface - 2D interface - Ethercat copper - cleanSTUDIO protocol - IPC 19" 1U - Touch panel standard 17-inch with HDMI+DP-VGA - Keyboard with trackball DE QWERTZ keyboard with trackball (DE)

Condition: new, Year of construction: 2026, functionality: fully functional, 1 m Roller Conveyor (4 Rollers) The 1 m roller conveyor (4 rollers) is a professional material support and feeding system designed for use with band saws and other machines requiring stable material support during feeding or receiving operations. Thanks to its robust construction, high load capacity of up to 900 kg, and four steel rollers mounted on bearings, this roller conveyor ensures safe and smooth transport of various types of materials, including pipes, profiles, flat bars, and shafts. It is an essential solution for modern production plants and professional workshops. Main advantages of the machine High load capacity – up to 900 kg, ideal for heavy steel components. 4 bearing-mounted steel rollers – diameter 60 mm, length 360 mm each. Adjustable height range of 650–1100 mm – allows adaptation to different machines. Expandable roller conveyor system – possibility of connecting multiple units. Reinforced construction – additional crossbars increase rigidity and stability. Design and technology The entire structure is based on a durable steel frame, additionally reinforced in areas exposed to the highest loads. The main working elements are four steel rollers mounted on precision bearings, ensuring minimal rolling resistance even under heavy loads. The 1000 mm long roller conveyor can operate as an independent module or be connected with additional sections to create a functional material handling system. The construction ensures safe and stable movement of components without the risk of shifting or slipping. Precision and work efficiency The roller conveyor significantly improves the efficiency of cutting, drilling, and welding processes by eliminating the need for manual material stabilization. The rollers rotate smoothly and evenly, allowing the operator to precisely position workpieces. An additional advantage is the adjustable working height, which enables integration with various types of machines – from band saws to machining tables and automated production lines. Applications Gbsdpfxovu R Dqe Aayet This model can be used in many industrial sectors, including: Facilities involved in cutting and material preparation. Production lines and machining workstations. Welding and structural fabrication companies. Steel and metal processing industries. It is a universal and durable solution for anyone who values stability and efficiency when working with large and heavy materials. Standard equipment 4 bearing-mounted steel rollers (60 × 360 mm) Steel frame with reinforcing elements Height adjustment system (650–1100 mm) Anti-slip leveling feet Technical specifications – 1 m roller conveyor (4 rollers) Parameter Value Roller diameter 60 mm Roller length 360 mm Number of rollers 4 Overall length 1000 mm Overall width 450 mm Height adjustment 650–1100 mm Maximum load capacity 900 kg Weight 50 kg

Condition: new, Year of construction: 2024, color: red, loading space volume: 20 m³, loading space width: 2,500 mm, loading space length: 6,900 mm, loading space height: 1,250 mm, gearing type: other, total length: 6,900 mm, driver cabin: other, Vehicle location: in transit, Structure: ARCHIVE IMAGES Roll-off container for water in accordance with DIN 14505 - Water transport for at least 10,000 liters - Length: approx. 6.90 m - Width: approx. 2.50 m - Height: approx. 1.25 m - Permissible total weight: 14,000 kg - Roll-off frame must be manufactured in accordance with DIN 14505:2015 - Water tank with baffles - Dome cover 60 x 60 cm square or round (diameter 60 cm) as entry and cleaning opening - Ventilation valve - Equipment compartment in the rear area for storing 2 B 5m filling hoses, folding containers (Husky 3000 Gal.) and water-carrying fittings, size: min. 80cm deep, 200cm wide, 100cm high, closed with a simple closing flap system or roller shutter - Complete emptying must be possible without a pump at the rear, e.g. two emptying nozzles min. DN 100 with shut-off valves and Storz A coupling DN 125 in the middle of the container with a shut-off valve, also accessible at the rear - Two access nozzles DN 75 with Storz B coupling and shut-off valve, free inlet into the tank, pipe routing in the lower area of the roll-off container on the right and left or both at the back, led outwards - Automatic ventilation and final ventilation valve, volume flow min. 3,000l min - Water level indicator - Color: red RAL 3000 - Storage box for 2 A hoses, dimensionally stable 5 m in roof box design - Plastic coating inside - with overflow possible for use on 3-axle vehicles (tank approx. 11,500L capacity) Delivery time approx. 10 - 12 weeks Available from 5,000-25,000 liters Price depending on the number of liters Gbodovhmqyjpfx Aayot between EUR 10,000.00 to approx. EUR 20,000.00 per number of liters/volume Available with self-priming water pump, self-lubricating with separate motor, delivery capacity: 129m³/hour 2000l/min, pump height: 17m, grain size: 28mm, fuel diesel, tank: 4.3 ltr., see 2907 for an additional charge of EUR 4,000! Available as a roll-off container and tank ACCESSORIES INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale and errors! - .

Condition: used, Year of construction: 2005, functionality: fully functional, cutting length (max.): 6,500 mm, input voltage: 400 V, - Year of manufacture: 2005 - Electrical diagram - Electric motor: 15 kW - Log cutting length: up to 6.5 meters - Control: stationary control panel - Additional equipment: - Hydraulic loading - Hydraulic hold-down Gbedpfx Ajyrdg Djayet - Hydraulic log turner - Roller adjustment - Debarker (for removing bark prior to cutting) - Dual-function hold-down - Side stops - Leveling rollers Machine dimensions: - length: 750 cm - width: 220 cm - height: 240 cm - weight ~1700 kg

Year of construction: 2012, condition: ready for operation (used), A repair-required OTI shot blasting machine is offered. 1) OTI GG A2-2500 blasting system, working length: 6000mm. 2) OTI blasting cabinet, cabinet dimensions X/Y/Z: 1650mm/13500mm/3800mm, internally illuminated, with automatically guided blast nozzles and rubber curtains for cabinet protection. 3) Chain conveyor unit, continuously variable motor-driven, with chain guide, roller conveyor, tension frame bearing and chain tensioner. 4) Oscillation, continuously variable motor-driven. 5) Blast media filling station, pneumatically operated, filling hopper: approx. 150kg, with level probe and shut-off slide, max. filling weight: approx. 200kg. 6) Cyclone separator/pre-separator system for separating reusable and spent blast media, with blast media recirculation into the blasting process and Big-Bag collection. 7) Filter system with radial fans, 2x 8 filter cartridges, cartridge dimensions X/Y: 330mm/1000mm, filter area: 14m²/cartridge, extraction capacity: 10000m³/h, with compressed air cleaning. 8) Final filter with pleated filter elements, 2x 2 filter elements, filter element dimensions X/Y: 915mm/915mm, separation efficiency: 99.9%. 9) Control cabinet with controller: Moeller Easy 820/618. 10) Operator panel with beacon/signal light, display, start pushbutton, key switch, emergency stop pushbutton and pressure gauges for operating pressure and inlet pressure. 11) Pressure vessel Maschinen- und Behälterbau GmbH, type MB 030603-1.1000, year of manufacture: 2012, volume: 1000l, permissible pressure: 11bar, min./max. permissible temperature: -10°C/50°C. Documentation available. An on-site inspection is possible. Godpezp Rg Rjfx Aayebt