Used Sarmax Single-Side Sanding Machine for sale (79,539)

Condition: ready for operation (used), Year of construction: 2014, functionality: fully functional, BOTTOM GRINDER FOR BEAMS WORKING DIMENSIONS 600x600 mm Ljdew E Ewxspfx Adtohf 15 kW

Condition: good (used), Year of construction: 1996, double-sided top and bottom sanding with sanding shoe and dust brush max. sanding width 300 mm max. sanding height 200 mm Lhodsxfl Eaepfx Adtsf year of manufacture 1994 with CE mark

Condition: excellent (used), Year of construction: 2003, Ref:11066 . 2003 Autobond105 THS. B1, single sided, fully automatic thermal laminator. Excellent condition run less than 1.5 million sheets! Equipped with; Heidelberg deep pile suction feeder with back separation 250mm (10) diameter highly polished chrome laminating roller Laminating nip pressure up to 6 metric tonnes Lhjdpfoydnxnsx Adtof Film is mounted on a quick change air shaft Trim slitter and perforating mechanism Pneumatic clutch ensures precise film tension Swiss made temperature control unit Sheeter - Integral bump roller separator with anti-curl bar Pallet delivery table. Accessories: Ioniser Pro static eliminator. Specification: Sheet size Max: 105 cm (40”) x 76 cm (30”) Min: A4 Paper weight 90 gsm (80lb) - 650 gsm (24 PT) Film Range - 8 micron virgin & 24 micron (1 mil) to 75 micron (3 mil) thermal Top speed 45m (150') per minute with rising pile feeder.

Condition: good (used), Year of construction: 2015, machine/vehicle number: 0-200-24-0779, functionality: fully functional, input voltage: 400 V, input current: 55 A, input frequency: 50 Hz, type of input current: three-phase, workpiece height (max.): 60 mm, edge thickness (max.): 20 mm, total length: 10,825 mm, Used single-sided HOMAG edge-banding machine for straight edges – KAL 370 For pre-milling (jointing trimming), gluing and post-processing of various kinds of edging materials. Fixed stop on the left side. Year of Manufacture: 2015 EQUIPMENT / SPECIFICATION BASIC MACHINE - with 80 mm wide conveyor chain with rubber-coated chain pads, - workpiece thickness 8 to 60 mm - top pressure with compound V-belt, automatic height adjustment (to workpiece thickness) - panel support with roller guide, extractable approx. 700 mm - glue roller drive in case of feed stop - hand switch /remote control for setup – mode - adjustable infeed fence with NC-axis (CAN-bus) - Jointing trimming 2 motors (clockwise, counterclockwise), 2x4kW, rear motor w. jumping function GLUING SECTION V20, consisting of: - QA60 glue application unit, with PTFE-coating (Teflon), with manual quick-adjustment glue gates - pneumatic clamping of glue application in mount - Pre-melter for EVA glue - Edge magazine, edge thickness min. 0,4 mm to max. 20 mm Edge width (height) max 65 mm - modes: edge rolls, (veneer) strips, solid wood edging - Pressure zone with automatic horizontal adjustment (NC CAN-axis) to edge thickness, 1 driven & 4 non-driven pressure rollers. Ljdsy A I Sgjpfx Adtohf POST-PROCESSING SECTION: - Snipping (end-trimming) unit PK85 horizontal, 2 motors, with straight/chamfer cutting function - Rough trimming 2x1.15 kW, top/bottom - Corner rounding FK11, 2 motors (top/bottom) with various trimming heads, motorised adjustment - Universal trimming unit, (e.g. grooving), 3.5 kW, tiltable, w. electro-pneumatic jumping control - Multi-Profile (radius-) scraping MN11 with automatic positioning by NC-axis (CAN) - Flat scraping (glue joint) FA20, top/bottom, (version with 3 tracer rollers) - Buffing unit FP10, top/bottom Control / software: - powerControl PC 23 PowerTouch - woodCommander 5 Machine dimensions 1085 x 180 x 235 cm (with opened doors)

Condition: good (used), Year of construction: 1992, Single-piece sanding machine sanding from top and bottom electric height adjustment with digital display continuously variable feed speed star/delta starter pneumatic belt tensioning Ljdpfx Adewyda Uotjhf main switch sanding belt oscillation finishing brush unit top and bottom, manual height adjustment Working width: 190 mm Working height: 4 - 150 mm Min. workpiece length: approx. 280 mm Abrasive belt dimensions (L x W): 1850 x 200 mm Feed speed: 5 - 25 m/min Installed power: approx. 14 kW Extraction port diameter: 2 x 180 mm Dimensions (L x W x H): 2000 x 1000 x 2050 mm Weight: approx. 1800 kg Incl. infeed and outfeed roller conveyor (L = 1600 mm, non-driven) Note on used machines: • Technical data subject to errors and prior sale. • Quoted prices are ex-works – loaded free of charge! • The machines have been cleaned and function-tested. • All machines are sold as inspected, with no claims to warranty. Buyers are welcome to inspect machines at the location. • Special agreements are only valid in written form. (We answer inquiries only when your address and telephone number are provided!)

Condition: excellent (used), Year of construction: 2001, machine/vehicle number: 0-200-24-6287, functionality: fully functional, input voltage: 400 V, input current: 56 A, edge thickness (max.): 20 mm, Equipment: CE marking, Used single-sided HOMAG edge-banding machine for straight edges – KL 78/A20/S2 For pre-milling (jointing trimming), gluing and post-processing of various kinds of edging materials. Fixed stop on the left side. Year of Manufacture: 2001 SPEZIFICATION & EQUIPMENT: Basic machine with 80 mm wide conveyor chain with rubber-coated chain pads, - workpiece thickness max. 60 mm - top pressure with compound V-belt, motorized height adjustment (to workpiece thickness) - panel support with roller guide, extractable approx. 700 mm - clamping of glue application unit before rear end of workpiece, for even glue application - glue roller drive in case of feed stop - hand switch /remote control for setup – mode - adjustable infeed fence with NC-axis (CAN-bus) - Jointing trimming 2 motors (clock-wise, counter clock-wise), 2x4kW, jumping function GLUING SECTION A20, consisting of: - QA34 glue application unit, on request with PTFE-coating (Teflon) - Pre-melter for EVA glues - Edge magazine, edge thickness min. 0,4 mm to max. 20 mm Edge width (height) max 65 mm - Pressure zone with automatic horizontal adjustment (NC CAN-axis) to edge thickness, 1 driven & 6 non-driven pressure rollers. POST-PROCESSING SECTION: - Snipping (end-trimming) unit HL81, 2 motors, with straight/chamfer cutting function motorised fine-positioning of snipping stop - Pre-milling (rough trimming) 1,5 kW, top/bottom - Corner rounding FK13, 2 motors (top/bottom) with automatic 8-fold tool changer and several exchangeable trimming heads - Profile (radius-) scraping MN21, with NC-axis positioning - Flat scraping (glue joint) FA10, top/bottom, (version with 3 tracer rollers) - Straight belt sanding unit KS10 - Buffing unit top/bottom Ledpfxjyv Da He Adtshf ELECTRONIC CONTROL: - HOMATIC NC21 OPERATING SYSTEM

Condition: used, Year of construction: 1988, - Grinding width: 190 mm - Grinding height: 4 - 150 mm Lsdpfx Asymnz Ujdtehf - 2 grinding units - Belt speed: 25 m/s - Feed speed: 5 - 25 m/min - Sanding belts: 1850 x 200 mm - Electrical connection: 400 V, 3/N, 50 Hz - Ex stock

Year of construction: 2016, condition: new, The single-sided polishing machine is a polishing machine for manual also robot editing to polishing of parts made of aluminium, steel, brass and zinc die-cast. Technical data: Polishing Pad: Max Ø 450 mm Spindle diameter: 35 mm Polishing wheel width: max 50 mm Suction connection: Ø 100 mm Dimensions (Lxwxh): 1800 x 1300 x 1800 mm Weight: 180 kg Supply voltage 3 x 400 V Power: 4 kW Height up to the polished shaft on request Made in Germany Lhsdpfxec Rfg Ue Adtjf Warranty: 12 months Optional: Extension with a frequency inverter will cost €950 per polishing machine. 1 piece FU, 1 potentiometer for regulating; 1 main switch

Condition: used, Year of construction: 2016, operating hours: 851 h, functionality: fully functional, machine/vehicle number: MN25724, working width: 1,500 mm, feed rate X-axis: 4 m/min, type of input current: three-phase, sheet thickness (max.): 50 mm, total length: 1,300 mm, total width: 2,600 mm, total height: 2,500 mm, overall weight: 2,600 kg, working height: 950 mm, workpiece height (max.): 50 mm, workpiece width (max.): 1,500 mm, The ER 1500 E is a deburring machine working from above on one side with the EdgeRacer carousel for precise processing of inner and outer contours with user-defined edge rounding. The EdgeRacer ER 1500 E offers a high throughput rate of more than 300 m²/h, surface-friendly processing - even with polished, brushed and foil-coated sheets - and reproducible results. Thanks to the roller conveyor of the EdgeRacer ER 1500 E, the sanding heads can also be fed below roller table level. The roller transport also ensures maximum energy efficiency - the processing costs are usually less than €0.01 per square meter of processed sheet metal. Thanks to the reversing operation, the sheets to be processed can be inserted and removed on the infeed side. Purchase the EdgeRacer deburring machine ER 1500 E as a demonstration machine with only 851 operating hours directly from the manufacturer. Lhjdpfxoucw Dzj Adtsf

Condition: excellent (used), Year of construction: 2004, grinding height: 100 mm, working width: 250 mm, grinding width: 250 mm, Double-sided brush sanding machine / profile sanding machine Manufacturer: Quickwood Model: QL 3 Year of manufacture: 2004 Texturing and sanding machine, double-sided operation, equipped with a total of 6 brush units. Machine suitable for integration into production lines due to constant table height. Working width: 250 mm Passage width: 300 mm Passage height: approx. 100 mm Minimum workpiece length: approx. 500 mm Equipped with: 2x brush units from below, each 1.5 kW, frequency controlled, suitable for texturing and sanding 2x brush units from below, each 1.5 kW, frequency controlled, suitable for texturing and sanding 2x brush units from above, each 0.75 kW, frequency controlled, suitable for fine sanding Pneumatically controlled pressure rollers for workpiece guidance and stabilization Feed rate steplessly adjustable, approx. 5 - 25 m/min Extraction connections: 150 mm Lsdpfx Asxvz Ulsdtjhf Dimensions approx. 2045 x 1350 x 1700 mm (LxWxH) Weight: approx. 1000 kg

Condition: good (used), Technical Specifications: • Minimum panel width: 55 mm Lhsdpfx Adoi E S Rletof • Minimum panel length: 140 mm • Panel thickness (min/max): 10 - 60 mm • Edge thickness: 0.4 - 3 mm • Maximum strip thickness: 12 mm Components and Functions: Composition Grinding units eeders End trimmers Trimmers Corner rounders Edge scrapers Brushes

Condition: ready for operation (used), Year of construction: 2004, I sell the 3-side brushing machine Quickwood CD2-1300, Year 2004. 2 pcs. Surface brushes from top 2 pcs. Side brushes Working width 1300mm Vacuum underpressure table with ventilator. Ljdpfsvylmqsx Adtshf Adjustable rotation and feeding speed. Suitable for rustical brushing and patina surface. Profiles possible. Made in Italy With full Documentation. Available immediately.

Condition: used, Year of construction: 1991, functionality: fully functional, total width: 2,000 mm, total height: 2,150 mm, total length: 2,450 mm, overall weight: 4,200 kg, power: 25 kW (33.99 HP), input voltage: 380 V, control type: manual, degree of automation: manual, actuation type: electric, Number of sanding units: 4 pcs Sanding width: 190 mm Lsdm U H Nfet Tqy Eofjrw Max. sanding height: 4–180 mm Weight: 4200 kg Hess Expert 4-Belt Single Wood Sanding Machine Ø Sanding from below/above Ø With 2 offset sanding units each (below and above) Ø Sanding units (below and above) arranged in series according to the planing principle Ø Pre-sanding with coarse grit (calibration) Ø Fine sanding with fine grit (finishing) Ø Central motorized height adjustment of the lower sanding units Ø Central motorized and synchronous height adjustment of the complete upper sanding and brushing units, including the upper feed units Ø Oscillating use of sanding belts (during the sanding process) Ø Absolute power connection via 5.5 kW motors and large-dimensioned drive drums Ø Oxide-ceramic sanding shoe for: - precise surface geometry - no need for readjustment - permanent dimensional accuracy - completely maintenance- and wear-free Lhodpoxzbdksfx Adtof Basic structure: Stable, heavy-duty welded construction made of thick-walled rectangular profiles with additional, statically calculated reinforcements for optimal vibration damping. Offset sanding units with large-scale belt drive drums for slip-free belt tracking. Dual-point extraction for direct and airborne dust, with sealing brushes and integrated sanding belt air-blast system to extend sanding belt service life. Sanding units made from heavy steel plate design as a basis for vibration-damped, smooth belt running. Absolutely backlash-free guides using ball linear sets made from hardened and ground shafts. Height adjustment of sanding units via hardened and ground special linear guides and preloaded guide carriages. Lasting precision due to dust and dirt protection of the ball linear sets and guide carriages. Large-diameter pre-sanding rollers serve as contact rollers. Contact rollers and sanding shoes are optimally matched to the sanding belt grit load. The large-dimensioned drive drums guarantee full transmission of the sanding motors’ 5.5 kW output to the sanding belt, ensuring slip-free, stable running and optimal heat dissipation. This enables maximum stock removal. Automatic machine stop trigger in the event of belt breakage. Optical indicator at the control panel and machine warning beacon. Finishing sanding shoes are completely maintenance- and wear-free, made from oxide-ceramic for optimal heat dissipation. Sanding belt tension by appropriately dimensioned pressure springs. Sanding belt release for belt changes using a pneumatic system for sensitive, distortion-free installation of new belts. Upper sanding unit and brushing device are centrally motorized, height-adjustable with digital display at the control panel for motorized sanding thickness adjustment. Integrated brushing and finishing device for improved surface finish, built into the main machine. Two vertically-aligned special brush rollers, 150 mm diameter, operating in the same direction as the feed. Separate height adjustment of the brush rollers using precise slide guides for wear compensation. Additional conveyor roller for removing or further transporting the workpiece out of the sanding machine, coupled with the transport belt. The Feeding mats have been recently changed

Condition: new, functionality: fully functional, Year of construction: 2025, control type: CNC control, degree of automation: automatic, laser type: fiber laser, laser power: 3,000 W, warranty duration: 24 months, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, nozzle changer, safety light barrier, Working Area (mm): 3048×1524 X-Axis Travel (mm）: 1524 Y-Axis Travel(mm）: 3048 Z-Axis Travel（mm）: 80 X/Y Axis Positioning Accuracy: ≤0.03mm/m X/Y Axis Repositioning Accuracy: ≤±0.02mm Maximum Synthetic Positioning Speed: 150m/min Maximum Acceleration: 1.2G Cutting Slit Width: 0.1mm-0.5mm (measured for platesless than3mm thick) Lodjxvwcxopfx Adtohf Cutting Surface Roughness: Ra3.2um-Ra25.4um(measured for plate thickness below3mm） Floor Size(mm): 6000*3000 Mainframe Dimension(mm): 5000*2300*1800 Screen Size: 21"LCD TransmissionMode: Rack andpinion dual drive Table Loading Capacity: 1.1(ton)

Condition: refurbished (used), Year of construction: 2003, functionality: fully functional, Key Facts: Lachenmeier Hood Stretcher Pallets per Hour: 50+ Frame Size: 3,000 x 2,400 mm Max. Load Height: 1,500 mm Max. Load LxW: 1,200 x 1,000 mm Stretch Hood Film: 1 Lsdpfx Aevb Tz Eodtjhf Special Features: refurbished stretch hood machine long-lasting spare parts by RHM Packaging Availability Now in stock at RHM

Condition: excellent (used), Year of construction: 2012, Ref:11057 . 2012 Autobond Mini 105 TPHS-FL B1, double sided, fully automatic thermal laminator. Equipped with; Heidelberg deep pile suction feeder with back separation 250mm (10) diameter highly polished chrome laminating rollers Laminating nip pressure up to 6 metric tonnes 2 x Twin Tool Temperature Controllers Sheets are laminated top and bottom in one pass Rubber counter-pressure roller becomes water heated Additional heated roller, quick-change inflatable air-shaft, and perforating mechanism for 2nd roll of film Film is mounted on a quick-change air shaft Trim slitter and perforating mechanism Pneumatic clutch ensures precise film tension Swiss made temperature control unit Sheeter - Integral bump roller separator with anti-curl bar Pallet delivery table Specification: Lhsdpfx Adsx U A D Ujtsf Max sheet size: 106 x 106 cm (41.73” x 41.73”) Min sheet size: 28.5 cm x 32 cm (11.5” x 12.5”) 115 gsm (80 lb text) to 650 gsm (24 pt) Max speed: 60 m/min (200 ft/min) B1 sheets up to 5,000 SPH.

Condition: as good as new (ex-display), Year of construction: 2026, 5222454 LIBRA 45/2 RTC 135 Wide Belt Sander 5257433 "Z" Designation for RTC 135 5257452 Vacuum table with electric fan 3 kW 5257453 Oscillating belt air-blast device for 5257454 Oscillating belt air-blast device for 5257462 Reinforced motor 15 kW (20 HP) 5257485 Roller table at infeed and outfeed for 5257499 Grooved rubber pressure roller, 2nd position 5257500 Grooved rubber pressure roller, 3rd position 5257504 Infinitely variable conveyor feed with inverter 5257605 Door with inspection window 5257606 LED lamp for internal illumination TECHNICAL DATA Dimensions and Weights Length (product) approx. 1800 mm Width/depth (product) approx. 2000 mm Height (product) approx. 2070 mm Extraction Connection Number of extraction ports: 2 Extraction port diameter: 200 mm Electrical Data Feed motor power: 0.8 kW Connection voltage: 400 V Mains frequency: 50 Hz Height adjustment motor power: 0.25 kW Output power (motor power): 11 kW Sanding Unit Sanding belt length: 2150 mm Sanding belt width: 1370 mm Max. sanding width: 1350 mm Feed Unit Lodpfx Adsy Ehiwotehf Feed speed: 4.5 / 9 m/min Workpiece Min. workpiece height: 4 mm Max. workpiece height: 170 mm Product Information EU 2023/2854 Type of generated data: usage data Format of generated data: common, machine-readable formats, e.g., JSON Data volume: up to 5 MB Continuous real-time data generation: yes Data storage location: on the device and a remote server Data access: on the device and via physical and wireless interfaces Location: ex stock 54634 Bitburg - immediately available -

Condition: used, Year of construction: 2008, machine/vehicle number: 0-411-49-1873, Technical data: - Manufacturer: Bütfering - Type: Optimat SGO 211/RC - Number of grinding units: 2 - Year of manufacture: 2008 - Working width: 1.100 mm - Grinding belt width: 1.120 mm - Grinding belt length: 1.900 mm - Workpiece thickness: 3-160 mm - Feed speed: 2,5-13 m/min. - Table height adjustment Standard equipment: - Automatic workpiece thickness adjustment - Stepless feed speed via requency converter. - 125 grinding programs can be stored - Wear-free braking system 1. Grinding unit (R) - Calibration roller - Profiled steel contact roller - Diameter 160 mm - Drive motor: 15 kW 2nd grinding unit (C) - Combination unit with roller and grinding shoe - Rubberized contact roller 65 Shore - Contact roller diameter 160 mm - Electronic link pressure bar with segment width 35 mm. - Belt speed: 12 and 21 m/s - Tolerance compensation up to 1 mm - Suitable for veneered surfaces and solid wood. - Drive motor: 11 kW - Total connected load: approx. 28 kW - Operating voltage: 400 V / 50 Hz. - Compressed air consumption at 6 bar, 20 L/min. - Belt blow-off device per pressure surge 440 L/min. - Extraction volume: approx. 2,880 m3/h/ at 20 m/s - Extraction connection: Dedusting: 1 x Ø 160 mm (grinding unit, roller) 1 x Ø 160 mm (grinding unit, shoe) Dimensions: Lsdpfx Ajyh Hwujdtehf - Length: 1,700 mm - Width: 1,850 mm - Height: 2,100 mm - Location: not in stock - Available from April 2026

Condition: used, Year of construction: 2001, machine/vehicle number: 001048, - Manufacturer: Unisanding - Type: 2.2.0. 0-30 - Working width: 1300mm - Year of manufacture 2000 - 2 rollers flexibly adjustable from 0-30 ° working from above - Flex-Trim special brushes - Vacuum belt with vacuum motor - With glass pane on the operating side - External control panel with LCD control - Grinding motors: 2 x 2.2 kW with thermal contact - Feed motor: 1 x 1.5 kW with thermal contact - Vacuum motor: 1 x 5.5 kW - Height axis rollers: 1 x 0.18 kW - Feed 2-10 m/min frequency controlled - Brush speed: 50 - 350 rpm, frequency controlled - Voltage: 3 x 400V, 50Hz - El. Power 15KW - Fuse: 63A - Exhaust air volume (vacuum) 3,000 m³/h Lhsdpfjxtakmox Adtjf - Dust extraction volume: 2,000m³/h – 5,000m³/h depending on the customer - Length: 2,170 mm - Width: 2,040mm - Height: 2,030 mm - Weight with control cabinet: 2220 kg - Color: RAL 7035 light gray - Operating side: left to right - Ex version: No - Location: at the Blomberg warehouse

Condition: good (used), functionality: fully functional, From insolvency: Edge sander Samco Unilev 15 -- fully functional -- Ledpfsy E Iwnsx Adtehf with oscillation Sanding belt 150x2170 mm Tables adjustable 0-30° 380 Volt Pneumatic belt tensioning 2 belt speeds Weight 405 kg Space required approx. 1500x800 mm

Condition: used, machine/vehicle number: 007354, Type of edging: Thin edge, Thick edge Gluing System: EVA Hotmelt Corner Rounding Unit: yes Combination Squaring Edgebanding Machine: First and Second Pass Lhjdpfx Adsyg Edajtsf Max Panel Width: 240 mm Max feed speed: 40 m/min Operating Units Right Side: 9 nr Operating Units Left Side: 9 nr

Condition: used, Polishing sander Löwer FA 4 S Year of construction 1998 Machine no. 9667 400V, 14.5Amp. Ljdewnh Avepfx Adtohf 4x 0.37kW motor Working length 3000mm Dimensions: 5000x18050x1600mm (LxWxH), weight 550kg - Documentation available: Yes - CE certificate present: No Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2008, total length: 2,060 mm, total width: 830 mm, total height: 1,180 mm, Empty weight: 566 kg - Year: 2008 - Documentation available: No - CE certificate present: No - Table length [mm]: 1000 - Table width [mm]: 400 - Sanding belt width [mm]: 200 - Sanding belt length [mm]: 3200 - Extraction nozzle diameter [mm]: 120 - Conveyor belt speed [m/s]: 13 - Min. tilting angle [°]: 0 - Max. tilting angle [°]: 45 Lhedpfx Adsywlfyetjf - Transport dimensions: 2060mm x 830mm x 1180mm (l x w x h) - Transport weight [kg]: 566kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: excellent (used), Wide Belt Sander FORMAT 4 Finish 1302 -used- Constant working height due to upper part adjustment, Combination unit with contact roller and sanding pad, Rubber-coated contact roller, Pneumatic activation of the contact roller, Electronic segmented sanding pad, Digital display for sanding height, Infinitely variable feed speed, Automatic belt centering, Operation via touchscreen display, Air-cushioned sanding pad, Sanding belt oscillation ----- Technical Data ----- Working width: 1,300 mm Number of belts: 2 units Sanding belt dimensions: 1,310 x 2,200 mm Feed speed: 3.7–16 m/min Segment width sanding pad: 55 mm Max. workpiece thickness: 170 mm Min. workpiece thickness: 5 mm Extraction port Ø: 2x200 mm Motor power: 18.5 kW Second motor power: 15 kW Dimensions (LxWxH): 1,950 x 2,250 x 2,600 mm Weight: 2,400 kg Quality Information: Lodpfsxnm Rcsx Adtshf - Belt tracking / balance checked - Sanding pad checked / refurbished - Height adjustment checked - Thorough basic cleaning - Electrical system checked - Immediately ready for use

Condition: used, Year of construction: 2020, Packaging machine Fully automatic side sealing machine Profi Packer Lhedpfsxuglmox Adtof Manufacturer: Schlichter Model: SCV 400 Pro Year of manufacture: 2020 Longitudinal sealing: continuous Photoelectric sensors: horizontal and vertical (standard) Compressed air: 6 bar Transport speed per minute: min. 5 meters, max. 30 meters Film core Ø: 76 mm Maximum film roll Ø: 350 mm, up to 700 mm with optional fold-down module! Maximum film roll width: 650 mm Sealing bar width: 300 mm Product width min. and max.: 50 mm to 410 mm Product height min. and max.: 1 to 250 mm Product length min. 50 mm, max. unlimited Film thickness: from 7 to 80 μm Film material: Polyolefin fine shrink films, polyethylene, PVC; PLA and other bio films Performance per minute: up to approx. 85 cycles Machine dimensions (L x W x H): 2,200 x 1,680 x 1,800 mm Weight: 800 kg Shrink tunnel: Model: SCT 400U Year of manufacture: 2020 Passage width: 450 mm Passage height: 280 mm Heating capacity: 14 kW Dimensions (L x W x H): 2,065 x 1,065 x 1,340 mm