Used Bending Segment for sale (4,047)

Condition: new, functionality: fully functional, Year of construction: 2024, control type: manual, working width: 1,270 mm, folding beam adjustment: 46 mm, bending angle (max.): 135 °, sheet thickness (max.): 2 mm, back gauge adjustment: manual, back gauge: 760 mm, overall weight: 380 kg, total length: 1,600 mm, total width: 850 mm, total height: 1,175 mm, Equipment: documentation/manual, Top and bottom blades removable in segments Includes manual backstop PNEUMATIC CYLINDER!!! Max. bending capacity over the entire working length ----- 2 mm Max. working length ----- 1270 mm Max. opening width ----- 46 mm Fgjdpoga T A Isfx Al Sjh Width of the fingers ----- 25 | 30 | 35 | 40 | 45 | 50 | 75 | 100 | 150 | 200 | 250 | 275 mm Max. bending angle ----- 0 - 135 degrees Weight ----- 380 KG Width ----- 1600 mm Depth ----- 850 mm Height ----- 1175 mm

Condition: new, Top and bottom blades removable in segments PNEUMATIC CYLINDER!!! Including manual back gauge Max. bending capacity over the entire working length ----- 1.2 mm Max. working length ----- 2000 mm Max. opening width ----- 30 mm Width of the fingers ----- 38 | 38 | 38 | 50 | 50 | 50 | 50 | 76 | 76 | 101 | 127 | 152 | 203 | 254 | 254 | 254 | 254 mm Fgsdpsga T Daofx Al Ssh Max. bending angle ----- 0 - 135 Weight ----- 590 KG Width ----- 2400 mm Depth ----- 850 mm Height ----- 1175 mm

Condition: new, functionality: fully functional, Year of construction: 2026, control type: manual, working width: 2,000 mm, bending angle (max.): 135 °, sheet thickness steel (max.): 1 mm, back gauge adjustment: manual, overall weight: 540 kg, total length: 2,400 mm, total width: 850 mm, total height: 1,175 mm, Finger bending machine with segmented top clamp PNEUMATIC CYLINDER!!! Including manual backstop Max. bending capacity over the entire working length ----- 1.2 mm Max. working length ----- 2000 mm Max. opening width ----- 30 mm Width of the fingers ----- 38 | 38 | 38 | 50 | 50 | 50 | 50 | 76 | 76 | 101 | 127 | 152 | 203 | 254 | 254 | 254 | 254 mm Max. bending angle ----- 0 - 135 Weight ----- 540 KG Width ----- 2400 mm Depth ----- 850 mm Height ----- 1175 mm Fgsdpfjga T Dpox Al Soh

Condition: good (used), Base for press brake tool, bending tool, die, bottom knife, lower tool, prism tool, reversible prism, 1-piece die block for die bending machine, die tool, folding tool -Tool: for press brake, base for press brake tool -Dimensions: see drawing in the photos -Dimensions: 2500/70/H22 mm -Weight: 26.1 kg Fodpfx Aegxgmbsl Sogh

Condition: used, Bending tool, die, upper knife, upper tool, straight tool, die tool, seam closing tool -Tool: for folding machine RAS Typ 74.30 -Dimensions: see the drawing in the photos Fgjdpogxgm Hofx Al Soh -Distance recess rail: center center 650 mm -Dimension: 3060/28/H121 mm -Weight: 65kg

Condition: new, Year of construction: 2024, PB 4 Bending Center With the Durma Bending Center, you will achieve error-free results with maximum speed and safety, fully automatic tool change, and minimal setup time. The Durma Bending Center, with its robust machine body, excellent precision, ergonomic design, and diverse bending functions, will occupy an important place in your operation. The combinations we can technically implement in punching and laser machines enable maximum time savings in your production processes. Our developed smart consumption, standard production independent of the operator, and Durma CNC Bending Center, which is manufactured after stable thermal conditioning, offer you the opportunity to generate profits against rising energy costs. The Durma Bending Center automatically performs simple and complex bending operations on sheet metal materials with a thickness between 0.5 and 4 mm. With its user-friendly, easy-to-operate interface and software that simplifies part programming, this product will be your solution partner. Technical Data: Maximum bending length: 2800 mm Minimum bending length: 350 mm Maximum sheet metal input length: 3050 mm Maximum sheet metal input width: 1524 mm Minimum bendable width: 150 mm Maximum bending height: 254 mm Maximum bending depth: 50 mm Maximum sheet metal rotation radius: 3300 mm Bending force: 500 KN Pressing force: 1000 KN Maximum sheet metal thickness: For Fe 410 N/mm2 material: 3.2 mm For Acc. Inox 600 N/mm2 material: 2.2 mm For Aluminum 260 N/mm2 material: 4 mm Minimum sheet metal thickness: 0.5 mm Maximum bending angle per stroke: ±135° Extended Functions: Negative bending capability on the last bend: Standard Automatic tool change option: ATS (Standard) Auxiliary clamping tools: Standard Lower auxiliary bending tools: AHD (Option) Upper auxiliary bending tools: AB (Option) Fgsdpfog Adi Rsx Al Soh Reversed bending arrangement: AB (Option)

Condition: new, Fully automated system Energy saving Industry 4.0 Durma Cloud Fgjdsg Adn Ispfx Al Ssh Fiber laser technology Environmental awareness Synchronous, minimal working area High, precise repeatability High process accuracy Compact design Low noise level Simple and fast installation Upon request, we will send you informational material.

Condition: used, Year of construction: 2012, Bandwidth: 1100 mm Fgsdpfx Aeglamnjl Ssh

Condition: used, Bandwidth: 175 mm Fgsdsglantopfx Al Ssh

Condition: excellent (used), Quick Snap brush segment, brush, plastic brush, nylon brush -Manufacturer: Tennant, brush, 20" nylon with plate, unused, original packaging -Type: 14967 Disco 20" D=500 -Number: 2x brushes available Fsdpfxsgtu Ubo Al Segh -Price: per piece -Dimensions: Ø 500 x 110 mm -Weight: 6 kg/piece

Condition: good (used), Base for press brake tool, bending tool, die, bottom knife, lower tool, prism tool, reversible prism, 1-piece die block for die bending machine, die tool, folding tool -Support for bending tool: from Promecam STPC 250 40 121 press brake -Length: 4200 mm Fgjdpfx Alshqf Rno Ssh -Dimensions: see drawing in the photos -Dimensions: 4200/106/H106 mm -Weight: 212 kg

Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Fgedpjh U Rzgefx Al Soh Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Condition: used, Ring bending machine, profile bending machine, three-roll bending machine, bending machine, pipe bending tool -Pipe bending tool: 6 pieces -Profile diameter: 32 to 80 mm, see photos -Socket: Ø 36 mm -Price: complete -Dimensions: 490/540/H190 mm -Weight: 50.1 kg Fgsdpfx Asf Ngcrjl Soh

Condition: used, Ring bending machine, profile bending machine, three-roll bending machine, bending machine, pipe bending tool -Pipe bending tool: 2 pieces -Profile diameter: 65/49 mm Fjdpfx Aof Nrp Tol Ssgh -Recording: dimensions see photos -Price: complete -Dimensions: 195/400/H220 mm -Weight: 42.7 kg

Condition: new, Year of construction: 2026, tube bender R 1 ZOPF - without bending tooling - with foot pedal and emergency stop - without tooling - control unit - 100 programs of 9 bends each - precise electronic control of C-shaft Fodefiqntopfx Al Ssgh - manual and automatic bending mode - bending angle and springback angle are programmable by means of a microprocessor - rapid engagement and disengagement of the tooling - scale for counterbending holder - movable - dimensions 930x410x1000 mm - weight 280 kg - motor 1,5 Kw - 220 volt single phase - bending radius R55 - R340 mm - bending capacity of tube Ø 5 mm to 50 mm - max. Bending angle of 210 °

Condition: good (used), Bending tool, die, upper blade, upper tool, straightening tool Fjdpfxsfiqq Ue Al Sjgh -Tool for: Press brake -Prisms: 90° x 75 mm -Dimensions: see drawing in the photos -Dimensions: 2500/270/H175 mm -Weight: 188 kg

Condition: good (used), Bending tool, die, upper blade, upper tool, deer foot tool, deer foot tool for press brake -Tool for: Press brake Fsdpfxofiqrno Al Ssgh -Dimensions: 3000/30/H116 mm -Weight: 48 kg

Year of construction: 1990, condition: good (used), machine/vehicle number: 2ß90 522, Technical specifications: - Bending capacity: Fgsdpfx Ajfndg Esl Sjh - Steel pipe: Ø 20 - 60 x 4 mm - Stainless steel pipe: Ø 20 - 50 x 3 mm - Max. bending moment: 6.2 cm - Max. bending angle: 180° - Max. radius: 125 mm - Bending speed: 8 sec - Drive: 400 V / 3 kW - Space requirement: approx. L 2400 x H 1600 x D 1000 mm - Weight: approx. 1400 kg - Includes: - Bending angle control via potentiometer with digital display - 6-fold preselection of bending angles - Internal + external pipe deburring tool - Bending tools Rx2.5D: Ø 38; Ø 50; Ø 65;

Condition: used, 4-column punching tool, cutting tool, punching tool, punch, punching die, punching punch, Fgsdpfodxnlfjx Al Soh -Punching tool with: bending function -Admission imensions: 300/205/H445 mm -Weight: 100 kg

Condition: good (used), Ring bending machine, profile bending machine, three-roll bending machine, bending machine Fgodpfx Aljd Naw Ae Sjh -Outer diameter: 200 mm -for: 35 mm pipe -Bearing seat: Ø 55 mm -Bore: Ø 49 mm -Quantity: 2 rolls available Price: complete -Dimensions: Ø 200 x 81 mm -Weight: 11 kg

Condition: new, shaft diameter: 30 mm, Equipment: CE marking, documentation/manual, emergency stop, - Shaft diameter 30 mm - Rotates to the right and left - Emergency stop - Documentation - 230V Fgsdpfx Alehvv Hqs Soh

Condition: new, Year of construction: 2025, roller diameter: 90 mm, working width: 700 mm, sheet thickness steel (max.): 35 mm, - Capacity 700 x 3.5 mm - Electrically adjustable rear roller - Digital display - Hardened rollers - 2 speeds - Conical roller - Swiveling top roller - Brake motor - Foot control Fsdpfx Alsr Ign Rj Sjgh - Emergency stop - Documentation - 400V

Condition: new, roller (top) diameter: 46 mm, roller diameter: 46 mm, - Capacity 1050 x 0.8 mm - Roll diameter 46 mm Fgodper Nvhaefx Al Seh - Conical roller - Swivel top roller - Documentation

Condition: used, Three-roll round, three-roll sheet metal bending machine, bending machine, sheet metal bending machine, 3-roll round bending machine, profile bending machine, three-roll sheet metal rolling machine -Spare part top roller -Drawing with the pictures -Max. Sheet width: 2060 mm -Max. Sheet thickness: mm -Roller diameter: 141 mm -Bearing diameter: 75 mm -Transport dimensions: 2690/141/H141 mm -Weight: 290 kg Fgjdpfxocx T E Re Al Ssh

Condition: used, Bending tool, die, bottom knife, bottom tool, prism tool, beading tool Fodpfocnz E Dsx Al Segh -Tool: for press brake -Prism width: 16 mm -Tool: shared -Tool: is guided -Tool intermediate dimensions: 1430 mm -Transport dimensions: 1550/200/H235 mm -Weight: 250kg