Used Cold Store for sale (3,128)

Condition: excellent (used), CTS Type: TSS-70/130 Water-cooled refrigeration unit For sale is a high-quality thermal shock test chamber by CTS (Clima Temperatur Systeme), model TSS-70/130. This device is designed for performing thermal shock tests and is typically used in industry, research, and quality assurance. Application Areas: - Material testing - Aging tests - Electronics and component testing - Thermal shock and temperature cycling tests Technical Specifications: Type: TSS-70/130 Test volume: 130 liters Temperature range: - Hot chamber: +50°C to +200°C - Cold chamber: -80°C to +100°C Heating rate: approx. 6 K/min from ambient temperature to +180°C Cooling rate: approx. 4 K/min from ambient temperature to -60°C Temperature deviation: - ±1 K over time - ±2 K spatially Temperature change rate: - max. 100 K/min average for shock test mode (no radiant heat) Transfer time between chambers: - ≤ 15 min for -65°C to +200°C with 10 kg ICs Changeover time: - < 10 seconds Electrical Specifications: Connection: 400 V, 3/N, 50 Hz Nominal power: approx. 17.2 kW Nominal current: approx. 29 A Site fuse: 32 A slow-blow Connection: Cekon 32 Refrigeration System: Refrigerant: R404A / R23 Water-cooled, low noise, fully hermetic Djdpfxjy Hkd Hs Anfekl Features/Equipment: - CTS control panel - Microprocessor-controlled regulation and monitoring system - Programmable operation (up to 100 test programs) - Digital setpoint and actual value display - RS232 interface - 2 free switching channels for external device control - Fault notification via volt-free contact (Loadable up to 30 V DC, 2 A) - EMC tested Technical Construction: - Hot and cold chambers - Transfer basket with spindle drive - Test chamber/transfer basket made of stainless steel (material no. 1.4301) - Stainless steel wire insert basket - Tube port NW 50 with sealing plug - Compressed air connection 1/4" male - Non-pressurized condensate drain R 1/2" female thread - Safety door locking - Lockable door with window Dimensions (according to installation diagram): External dimensions approx.: 2335 x 940 x 1820 mm Installation clearance approx.: 1990 x 940 x 1652 mm Test chamber internal dimensions: height approx. 410 mm, width approx. 480 mm, depth approx. 660 mm Window: 300 x 300 mm Additional Data: Protection class: IP 22 Sound pressure level: < 60 dB(A) Weight: approx. 950 kg Average consumption during test cycle: approx. 8 kWh Important information for your safety as a buyer! The following points are performed on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If required, refill with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, chambers undergo a documented test run. Condition: used Scope of delivery: see photos (Specifications subject to change and errors excepted.) For further questions, please feel free to contact us by phone.

Condition: used, Year of construction: 1979, saw blade diameter 300 mm cutting diameter 100 mm saw blade turning speeds 40 / 80 U/min capacity 90 degrees: square 90 mm Djdpjy N D Nnsfx Anfekl capacity 90 degrees: round 100 mm total power requirement 1,5 kW weight of the machine ca. 0,5 t

Condition: used, Year of construction: 1976, functionality: fully functional, Cold former double stroke, cold press Max. dimensions for standard bolts: M12 x 150 mm Max. wire cutting length: 180 mm Max. output: 105 pieces/min The machine can be viewed whilst powered on. Dodpsy N N Iiofx Anfokl Weight: 10 t

Condition: excellent (used), Year of construction: 2003, Max. saw blade diameter: up to 300 mm Machine head tiltable: 45°-90°-45°-30° Cutting diameter at 90°: 100 mm Square tube: 85 x 85 mm Flat profiles, hollow: 130 x 85 mm Speed range: 40 / 80 rpm Drive power: 1.0 / 1.2 kW Machine dimensions (L x W x H): 650 x 600 x 1650 mm Weight: 185 kg Dodpfjy E Ullex Anfokl Accessories / Special Features: • Vertical guidance of the saw head • Continuously adjustable mitre facility 45°-90°-45°-30° • Infeed/outfeed roller conveyors, each approx. 1 m in length • Manual feed • Coolant system • 1 saw blade included • CE compliant This very good VMS 300 is from a training workshop. Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel / Germany

Condition: used, Year of construction: 2019, Used machine Year of manufacture: 2019 Equipment and Technical Data: - For classic nesting processing with wear plate - Machine frame of welded construction with ground and hardened prism guides for the gantry, unit head, and consoles - Gantry-type traveling column - Helical rack and pinion drive in X and Y axes, ball screw in Z axis for precise positioning - Working dimensions: - Max. support area on nesting table: X = 3100 mm, Y = 1560 mm - Max. traverse paths: X = 4695 mm, Y = 2100 mm, Z = 293 mm - Max. clearance height over DYNESTIC table: Z = 100 mm from table top (without wear plate) - Maximum programmable speed Vector speed: 128 m/min X = 80 m/min, Y = 100 m/min, Z = 25 m/min - DYNESTIC table: - Fixed, continuous processing table with grid layout - Continuous grooves in X and Y directions - Groove spacing: 50 mm - Includes 25 meters of sealing cord for clamping the wear plate - Vacuum fields: Single-circuit vacuum system - Drilling unit 7877: - 19 spindles - Drive power: 1.7 kW - 13 vertical spindles: - Individually selectable - Arranged in U-shape - 5+4 in X direction, 4 in Y direction - 32 mm spacing - Max. drill diameter: 35 mm - Total drill length: 70 mm from screw-on end (depending on panel thickness) - Spindle stroke: 70 mm - Rotational direction: alternating clockwise/counterclockwise Dodpewka Upefx Anfjkl - Speed (max): 1000 - 4400 rpm, infinitely variable - Tool holder: M10 thread, 11 mm fit - Without tool, without holder - 6 horizontal spindles: - 2 double drill spindles in X direction - 1 double drill spindle in Y direction - Tool holder: M10 thread, 11 mm fit - Max. total drill length: 63 mm from screw-on end - Without tool, without holder - Milling unit 7842: - Power: 12.0 kW (S6) - Max. speed = 1000 - 24,000 rpm, infinitely variable - Max. power at 12,000 to 24,000 rpm - Air-cooled - With HSK-F 63 tool holder - With right-hand threaded nut (for right-hand rotating tools) - With collet chuck for HSK shank - Ceramic ball bearings (hybrid bearings) - Tool weight max. 6 kg (incl. holder) - Tools: milling and grinding tools max. Ø 160 mm - Safety enclosure according to CE standard - Side and rear safety fence - Vacuum pump: 500 m³/h, dry-running - Personnel safety ensured by light barriers in the front machine area - Hand-held control device for remote operation of the machine with the following functions: - Start/stop of the processing program - Control of processing cycle speed - Reset button - Manual feed/rapid traverse for all axes - EMERGENCY STOP - CAMPUS V7 CAD/CAM software 1x machine license consisting of: - CAMPUS NC-HOPS: - Graphic variant system with WOP and CAD/CAM features for creating part variants using macro technology - CAMPUS MT-Manager - CAMPUS Workcenter - CAMPUS DXF interface - Automatic central lubrication - Automatic lubrication at defined intervals - Additional sealing against dust via pressurization in each guide carriage

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, Very well-maintained Behringer VMS 370 A, including infeed and outfeed roller conveyors. The machine is now in stock, refurbished, and available for immediate delivery. Dsdpfx Ajy Edcyenfekl

Condition: not inspected (used), functionality: unexamined, total width: 1,200 mm, total length: 3,000 mm, total height: 1,500 mm, overall weight: 2,000 kg, No reserve price – guaranteed sale to the highest bidder! Placing a bid commits you to timely collection between 23/06/2026 and 26/06/2026! MACHINE DETAILS Overall length: 3,000 mm Overall width: 1,200 mm Overall height: 1,500 mm Machine weight: 2,000 kg Dksdpfoy D Tl Uox Anfel External reference: 41

Year of construction: 1970, condition: not inspected (used), functionality: unexamined, overall weight: 2,000 kg, total length: 3,000 mm, total width: 1,200 mm, total height: 1,500 mm, machine/vehicle number: 779, No reserve price – guaranteed sale to the highest bidder! Dsdpey D Tkdjfx Anfokl Placing a bid obligates timely collection between 23/06/2026 and 26/06/2026! TECHNICAL DETAILS Diameter: 5.4 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 3,000 x 1,200 x 1,500 mm Machine weight: 2,000 kg External reference: 40

Condition: not inspected (used), Year of construction: 1958, functionality: unexamined, machine/vehicle number: 202, wheel diameter: 885 mm, production capacity: 4,200 unit/h, No minimum price – guaranteed sale to the highest bidder! Placing a bid obligates you to collect the item within the period from 23/06/2026 to 26/06/2026! TECHNICAL DETAILS Maximum bolt diameter: 7.7 mm Maximum thread: M8 Maximum shank length: 90 mm Minimum shank length: 20 mm Output: approx. 35/53/70 pcs/min Flywheel diameter: 885 mm Dkodpfsy D Tfhex Anfol MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 4,000 x 2,000 x 1,500 mm Machine weight: 2,500 kg External reference: 42

Condition: used, Year of construction: 2023, numbers of pallets 15 dimensions 1,80 x 1,30 x 1,18 m Dodpfx Aey Eh Akjnfokl The pallet magazine is unused. Accessories, tools, and clamping devices shown are only included in the scope of delivery if this is noted in the additional information. Technical data and specifications are subject to change without notice. Prior sale is reserved.

Condition: used, Year of construction: 2000, Overview This cold glue labeling machine was manufactured in 2000 by Krones. The machine is designed for the application of cold glue labels on bottles. The machine is equipped with three labeling aggregates (front, back, and neck/seal label) and operates with a 20-head rotary table, making it suitable for medium-speed beverage production lines. The unit includes an integrated Krones Checkmat inspection system for quality control and comes with 11 bottle formats (0.5 – 1.0 L). Maintenance was performed as required. Technical data Capacity: up to approx. 15,000 bph Formats: 0.5 L – 1.0 L, 11 formats Application: Cold glue labeling of bottles Configuration: 20-head rotary table, 3 labeling aggregates Label positions: Front, back, neck/seal label Utilities: Standard Krones control system Incl. 3 glue pumps for cold glue system, Inspection system (Krones Checkmat), Format parts, Documentation Dkjdpjy Azv Ssfx Anfsl

Condition: good (used), Year of construction: 1974, Offer 26003 Technical Data: Dsdpfey Nlnxex Anfjkl - Saw blade diameter: up to 370 mm - Cutting capacity at 90°: - round: 110 mm - square: 100 mm - rectangular: 280 x 40 mm or 240 x 85 mm - Cutting capacity at 45°: - round: 110 mm - square: 100 mm - rectangular: 220 x 40 mm - Mitre adjustment left and right: each 0 - 90° - 2 cutting speeds: 13 + 26 m/min - Drive: 380 V / 1.2 / 1.8 kW - Saw blade feed rate hydraulically, steplessly adjustable - Coolant system - Required space approx. W 800 x H 1850 x D 1100 mm - Weight approx. 750 kg

Condition: excellent (used), Year of construction: 2007, BIMAX TA 91 Automatic Circular Saw TECHNICAL DATA Total power requirement, rotary current: 3 x 400 V For pneumatic machines: 3 kW For hydraulic machines: 3 kW Customer-provided mains fuse: 16 A Supply line: 4 x 2.5 mm, 3P + E Air connection: Diameter: 12 mm Supply line: 8 – 10 bar, 40 l/min Operating pressure: 6 bar Spindle drive via three-phase motor: B5-100S 4/2-pole, Dahlander circuit: 1420 / 2840 rpm Power: 1.8 / 2.5 kW Saw blade mount: 32 mm Drive pin: 8 mm Pitch circle of drive pin: 45 mm Cutting wheel mount: 22 mm Djdpfx Ajv I Dmlonfekl Saw blades: 160 x 1 to 300 x 2 mm Passage range: Round up to 65 mm Square up to 55 x 55 mm Rectangular up to 80 x 50 mm Standard clamping jaw for diameters: 10 – 60 mm Material feed length: 0 – 250 mm Saw weight: 500 kg Hydraulics: 120 kg No liability is assumed for the accuracy, completeness, or timeliness of this information.

Condition: good (used), Year of construction: 2002, Behringer Eisele VA-0-250-NC Circular saw Dksdpsvdk A Ejfx Anfel TECHNICAL DATA Sawing range: 90 ° Saw blade diameter: 25 cm Bore: 40 mm Cutting range: 10-75 mm Cutting length: 5-900 mm Speed: 2800 rpm Cutting speeds: 26/52/103/206 SFPM or 0.13/0.26/0.52/1.05 m/s Feed speeds: 0-40 mm/sec NC axis: Yes Dimensions: 190 x 127 x 190 Weight: 1300 kg We assume no liability for the accuracy, completeness and up-to-dateness of the information provided

Year of construction: 2008, condition: ready for operation (used), A fully automatic high-speed tube circular saw Bewo is available. Round tube diameter range: 8mm-90mm, min. square profile dimensions X/Y: 10mm/10mm, max. square profile dimensions X/Y: 80mm/80mm, feed rate: 50m/min-300m/min, saw blade diameter: 350mm, max. throughput capacity: 8000pieces/h, max. simultaneous machining: 4 tubes. Documentation available. An on-site inspection is possible. Djdpfxjy Nm Umo Anfjkl

Condition: new, saw blade diameter 350 mm capacity 90 degrees: round 115 mm capacity 90 degrees: square 100 mm capacity 90 degrees: flat 130 x 80 mm capacity 45 degrees: round 100 mm capacity 45 degrees: square 85 mm capacity 60 degrees: flat 90 x 80 mm clamping range 130 mm turning speeds 30 / 60 U/min dimensions of saw-blade 350 x 32 x 2,5 mm total power requirement 1,1 / 2,2 kW Dedpfx Aefmck Henfekl weight of the machine ca. 0,22 t dimensions of the machine ca. 1200 x 860 x 900 m Aktionspreis 2026 Inkl. base frame !!! Manual miter saw for miter cuts from 45° left to 45° right. Steel worm wheel with double ball bearings Saw blade shaft mounted on eccentric made of spheroidal cast iron Bronze wheel with wedge and conical coupling to ensure maximum power transmission to the steel worm wheel Vice with adjustable guide bars Adjustable anti-cutting burr device (enables burr-free cutting) Length stop Double return springs Safety main switch Emergency stop button Speed switch Electric coolant pump for lubrication and cooling of the saw blade (attachment a micro spray device possible) Motor 1.5/1.8 kW - 400 volts

Year of construction: 1991, condition: used, Volume: 15 hl Periphery: Pump Djdpew Tml Eefx Anfekl

Year of construction: 1995, condition: used, This filter system may only be used to filter preclarified products that have normal filterable properties in their composition. Max. filtration flow: 400 hl/h continuous Permissible operating pressure: 6 bar Permissible operating temperature: 105 °C Volume: 1456 l Current: 10 A Voltage: 220 V Water: cold water: min. 150 hl/h; hot water (max 65 °C): min. 150 hl/h Compressed air: prepared compressed air: 4 - 6 bar; control air: 5 - 8 bar Dksdpfx Ajvcqv Njnfjl Weight: 3450 kg Base construction: basic frame with control and measuring components and filter container; cleaning module Features: 98 filter cartridges, 3 piston diaphragm pumps (Dosage), centrifugal pump with frequency converter (WT circuit), various analog and digital sensors (flow, pressure, level, temperature, conductance), various valves, control cabinet

Condition: used, Length: ca. 2.6 m Width: ca. 1.7 m Height: ca. 2.3 m Features: Cooling unit (Technobloc, type: ACN050U, output: 0.7 kW, refrigerant: R404a) Dodsw Tmlljpfx Anfjkl

Year of construction: 2001, condition: used, The Pall CFS system is designed as a single unit and can be installed directly in front of the filling line without the need for a buffer system. It is a completely independent process unit consisting of the following components: filter vessel Piping and connections Membrane cleaning system (CIP) integrity check Switchboard The hygienic design, the simple integrity test and the full automation ensure the microbiological safety of the system and usually allow the operation of the filling staff. Cluster filtering groups filter elements into clusters. Each cluster has its own outlet valve. During filtration, all clusters are open. Cleaning, sterilization and integrity testing are performed per cluster. Advantages of the CFS principle; Longer life Integrity testing on site Integrity diagnostics per cluster Special rinsing High specific flow rate Short flush times Constant flow in all candles Minimal water consumption Quick replacement of filter elements Controlled backwash Minimal beer loss High biological safety Constant availability With this filter system only preclarified products may be filtered, which have normally filterable properties in their composition. Max. filtration flow: 400 hl/h continuous Permissible operating pressure: 6 bar Permissible operating temperature: 105 °C Volume: 1456 l Dkedpfx Anevcqx Djfol Current: 10 A Voltage: 220 V Water: cold water: min. 150 hl/h; hot water (max 65 ° C): min. 150 hl/h Compressed air: prepared compressed air: 4 - 6 bar; control air: 5 - 8 bar Length: 1,40 m Width: 1,20 m Height: 1,85 m Weight: 3450 kg Base construction: basic frame with control and measuring components and filter container; cleaning module Features: 98 filter cartridges, 3 piston diaphragm pumps (Dosage), centrifugal pump with frequency converter (WT circuit), various analog and digital sensors (flow, pressure, level, temperature, conductance), various valves, control cabinet

Condition: used, Year of construction: 1990, saw blade diameter 300 mm cutting diameter 90 mm Dodpfoy Ehx Esx Anfjkl turning speeds 40/80 U/min total power requirement 1,5 kW weight of the machine ca. 350 Kg dimensions of the machine ca. 0,9 x 0,8 x 1,5 m Cold circular saw - Machine light - Coolant system

Condition: like new (used), Year of construction: 2023, functionality: fully functional, total width: 5,150 mm, total length: 16,000 mm, total height: 4,850 mm, temperature: 2 °C, We are offering this as-new Heidinger I-1751 refrigeration cell, year of manufacture 2023. Type: I-1751 Dedpfx Anoykrtpefekl Year: 2023 Double refrigeration cell 2-8°C (unused) Each unit features a Viessmann double door (2m x 2.7m) Redundantly designed Internal dimensions per cell approx. 16m (L) x 5.15m (W) x 4.85m (H) Walls made of 100mm sandwich panels No dedicated floor, thus accessible by forklift Compressors: 4x Bitzer Ecostar LHV5E/2DES-3.F1Y-40S Evaporators: 4x Güntner GACC RX 040.1/2WN/DJA4A.UNNN The refrigeration cell was set up for the storage of pharmaceuticals and has never been commissioned after manufacturer inspection. The pallet racking shown is not included in the offer. If you have any questions or need further information, please feel free to send us a message or give us a call.

Condition: used, Year of construction: 2021, Overview This rotary cold glue labelling machine was manufactured in 2021 by Germany GERNEP. The machine is designed for cold glue labelling of glass bottles, primarily in the beer industry. It is equipped with one cold glue labelling aggregate and is prepared for the installation of an additional unit. The system features a mechanical bottle table drive (control cam system) and a Krones glue pump for consistent label application. Technical data Capacity: approx. 5,000 bottles/hour Speed range: approx. 1,000 – 6,000 bottles/hour Formats: 0.33 L / 0.5 L glass bottles Application: Labelling of glass bottles (beer) Configuration: Rotary machine with 1 cold glue labelling aggregate (prepared for 2nd unit) Label positions: Body / wrap label, neck / chest label Utilities: 400 V / 50 Hz / GND / N Scope of Delivery Labelling machine | GERNEP | Labetta 4/3/8 480 1A | 2021 | Rotary cold glue labeller with 1 aggregate (prepared for second unit) Glue system | Krones | Glue pump Control system | GERNEP | Touch panel Dedeyzcyvspfx Anfskl

Condition: used, Year of construction: 2019, Overview This rotary cold glue labelling machine was manufactured in 2019 by Germany GERNEP. The machine is designed for cold glue labelling of glass bottles, particularly in the wine industry. It is equipped with two cold glue labelling aggregates for the application of body, neck ring and back labels. The machine features a servo-driven bottle table and a Krones glue pump for precise label application. Technical data Capacity: approx. 5,000 bottles/hour Speed range: approx. 1,000 – 5,500 bottles/hour Formats: 0.75 L Bordeaux (H=309 mm, Ø74 mm) 0.75 L Schlegel (H=330 mm, Ø76 mm / H=350 mm, Ø78 mm) 1.0 L Schlegel (H=309 mm, Ø89 mm) 0.75 L Burgunder (H=297 mm, Ø82 mm) Application: Labelling of glass bottles (wine) Configuration: Rotary machine with 2 cold glue labelling aggregates Label positions: Body (front), neck ring, back Utilities: 400 V / 50 Hz / 3 Phase / N / PE Scope of Delivery Labelling machine | GERNEP | Labetta 4/3/12 784 2A SD | 2019 | Rotary cold glue labeller with 2 aggregates Glue system | Krones | Glue pump Control panel | GERNEP | Touch panel Dsdpfx Asyzcycsnfekl

Condition: excellent (used), mileage: 7,575 km, power: 90 kW (122.37 HP), first registration: 06/2023, fuel type: diesel, axle configuration: 4x2, wheelbase: 3,640 mm, fuel: diesel, color: white, driver cabin: day cab, gearing type: mechanical, number of gears: 6, emission class: euro6, total length: 6,250 mm, total width: 2,090 mm, permissible axle load (axle 1): 2,100 kg, permissible axle load (axle 2): 2,250 kg, Year of construction: 2023, Equipment: ABS, AdBlue, Apple CarPlay, Bluetooth, airbag, cruise control, electric window regulation, electronic stability program (ESP), full service history, navigation system, onboard computer, power assisted steering, power mirror, soot filter, traction control, = Additional options and equipment = - Alarm system - Outside temperature display Dkjdoy A Sg Iopfx Anfsl - Cup holder - Passenger airbag - Tachometer - Third brake light - Electric front windows - Driver’s seat height adjustment - Tinted glass - Particulate filter - Radio/CD player - Spare wheel - Disc brakes - Side doors - Immobilizer = Remarks = Refrigeration unit brand: Cold Car = Further information = Technical information Number of cylinders: 4 Engine displacement: 1,968 cc Maximum front axle load: 2,100 kg Maximum rear axle load: 2,250 kg Weights Unladen weight: 3,145 kg Payload: 355 kg Gross vehicle weight: 3,500 kg Maintenance APK (Technical Inspection): New TÜV upon delivery History Booklets: Available (dealer serviced) Condition Technical condition: Very good Visual condition: Very good Damages: None Warranty Warranty: 3 months = Company information = Nidro Cars Holland is located in the centre of the country and is your trusted address for purchasing a car, van, or truck. The indicated price is the 'internet take-away price.' For questions or to schedule a test drive, please contact us: SEE OUR COMPLETE STOCK AT All types of trade-ins are welcome! (Our listings are created with great care; however, no rights can be derived from their content.)