Industrial trailer VAL30 – 10 tons

Multi-Trans VAL30

Condition: excellent (used), total length: 6,000 mm, total width: 2,400 mm, total height: 670 mm, OPTIONALLY ALSO AVAILABLE WITH ROOF STRUCTURE! Operating Conditions: The trailer is designed for use on flat, paved surfaces in internal company transport. Combined Operation: Iasdpfxjxrtdqo Aa Ijr The trailer components are not (without a trailer coupling) designed for combined operation with multiple trailers. Payload: 16 t at 6 km/h with evenly distributed loading (area load) of the loading platform between the axles. Point or line loads are only permitted upon notification. Loading Platform: Approx. 6000 x 2400 mm, loading height approx. 670 mm, platform covering made of softwood planks, all-round edge protection. Steering: Four-wheel stub-axle steering, drawbar tiltable, removable, and can be repositioned from front to back, coupling height at the towing vehicle approx. 320 mm (other coupling heights only permitted upon notification), towing eye according to DIN 74054, diameter 40 mm, drawbar drop protection according to UVV. Chassis: Both axles steered, solid rubber elastic tyres approx. 425 x 300 mm, wheel hubs with tapered roller bearings and permanent grease lubrication. Paintwork: Topcoat RAL 5002 Ultramarine Blue. Optional Equipment: - 2 lashing rods made of round steel welded vertically into the outer frame on each long side - Double-acting wheel chock with holder and chain

Condition: as good as new (ex-display), ►►► FRONIUS TPS 3200 SET OFFER ✅ Scope of delivery: ➤ Fronius TPS 3200 Power Source (320A TRANS PULS SYNERGIC) ➤ Fronius FK 4000 FC Cooling Unit – Standard features include Flow Control, Thermocontrol, and coolant filter. The cooling unit shuts off if the water cooling fails or gets too hot, to protect the torch package. These functions cost approximately €400 extra from Fronius. ➤ Fronius VR 7000 Wire Feed Case – Compact and practical – in our experience, the most useful wire feed case – the wire is securely stored in the closed case. ➤ Fronius Intermediate Hose Package, long version – each machine is supplied with a 5-meter-long connection hose between the power source and the wire feed case for greater flexibility and improved handling. Take the wire feed case off the machine to access hard-to-reach areas! The connecting hose is neatly stored on a hook on the side of the machine. (Hooks are produced by us) ➤ Fronius Large Trolley – Probably the best trolley with a gas bottle holder on the market. ➤ Binzel Torch Package – With up/down amperage control on the torch. ➤ Ground cable 3-4m ➤ New Messer pressure regulator ➤ New basket reel adapter for large wire spools With this machine, almost all materials can be welded, including aluminum, steel, and stainless steel (V2A). It features pulse wire programs and is also suitable for MIG brazing (CuSi), commonly used in the sheet metal industry. Additional options are available at extra charge For example: Fronius Aw4000/Aw5000 Job Master Torch Package (with display on torch) + EUR 550.00 ----- Iajdpswbil Ssfx Aa Ior IMMEDIATELY AVAILABLE PROPER INVOICE Inspection is possible in Austria, Vienna 1230! ✔ Insured shipping on a pallet is no problem! ✔ We are also available via WhatsApp and Viber. ✅Questions✅Questions✅Questions✅Questions: ✅Questions✅Questions✅Questions✅ ►►► What is the condition of the equipment? For clarification: we purchase nearly new used equipment, disassemble and thoroughly inspect everything, replace wear parts as necessary, and only after a successful test weld do we release the equipment for sale. "All" machines are clean with no burn marks on the displays and without numerous burn holes or dents! With us, you buy an item that is ⭐in excellent condition and doesn’t look worn out! ►►► Do we receive an invoice when purchasing from you? Yes, you will receive a proper invoice from us. If you have a valid VAT ID and meet the requirements for intra-community delivery within the EU, we can issue a net invoice. ►►► What payment options are available? Prepayment or cash on personal collection. ►►► Why buy from us? We are experts in this series of Fronius welding machines and always have 60-80 units in stock – exclusively Fronius, no other brands! We know these machines inside out and do not sell anything we don’t have expertise in.

Condition: excellent (used), total length: 6,000 mm, total width: 2,400 mm, total height: 750 mm, color: blue, Operating conditions: The industrial trailer is designed for use on level, paved surfaces in internal transport operations. Multiple trailer operation: The trailer components are not designed (without a coupling device) for combined operation with multiple trailers. Payload: The industrial trailer can carry loads up to a maximum of 25 t at 6 km/h with evenly distributed loading (surface load) between the axles. Point or line loads are only permissible upon notification. Base frame: The base frame of the industrial trailer consists of a robust welded construction made of profile steel. Loading platform: Dimensions are approx. 6000 x 2400 mm. Loading height approx. 750 mm. The platform is covered with softwood planks and bordered with all-round edge protection. Steering: Four-wheel axle pivot steering, drawbar can be raised, detached, and swapped from front to rear. Drawbar eye height at towing vehicle approx. 285 – 775 mm (other heights only possible upon notification), drawbar eye according to DIN 74054, diameter 40 mm, drawbar drop safety device according to UVV. Chassis: Both axles of the industrial trailer are steered. Solid elastic rubber tires approx. 559 x 356 mm, wheel hubs with tapered roller bearings and long-life grease lubrication. Paintwork: Finish in RAL 5002 ultramarine blue. Additional equipment: Two lashing rods made of round steel are welded vertically into the outer side frames on each longitudinal side of the industrial trailer. Iasdpfx Ajxrtb Noa Ior Rental or sale EU-wide.

Condition: used, total length: 10,500 mm, Year of construction: 2016, load capacity: 14,000 kg, Trailer Multi-Trans VAL 30 Iaodpfsxd Edmex Aa Isr Drive No Drive Year built 2016 Lifting weight (kg) 14,000

Condition: refurbished (used), functionality: fully functional, travel distance X-axis: 475 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 400 mm, workpiece weight (max.): 200 kg, rotational speed (max.): 42,000 rpm, table diameter: 450 mm, 5-axis Röders Tec RXP800DS -completely overhauled- The machine is completely overhauled, checked and measured in our company. The machine again meets the new machine tolerance! Working area: - X-axis: 475 mm - Y-axis: 600 mm - Z-axis: 400 mm - Clearance height: 500 mm Tool changer: 52-way Spindle: HSK40E max. 42,000 rpm Iaodpfjvvlmcox Aa Ijr Tool measuring laser for tool measurement Handbox Minimal quantity lubrication Prepared for extraction system (e.g. for graphite) Spindle compensation Accuracy package Control: Röders RMS6 in current version A viewing of the machine in operational condition is possible at any time. You are also welcome to find out more about the type and scope of our reconditioned machines on our website or on our Hüttmann YouTube channel.

Condition: new, range L-W-H 780x480x105 mm weight 79,5 kg 7 St. Tool trolley with 7 drawers. Tool trolley has two normal and two swivel castors with brakes. Tool trolley completely lockable with an integrated lock. Drawers can be locked per compartment. All drawers equipped with quick lock and soft-closing mechanism. Tool trolley is equipped with 196 pieces of tool parts: 3 pcs socket wrench sets: 1/4" from 4 - 14mm, 3/8" from 6 - 22mm and Torx from E10 - E20, 1/2" from 8 - 32mm. Various screwdriver sets. Extension for socket wrench sets, various Allen keys from 1 - 10mm, Iaodpfx Aaou Imhcs Ior various files. Ratchet ring spanner set from 6 - 22mm, ring spanner set from 6 - 22mm. Pliers range.

Year of construction: 2022, operating hours: 108 h, condition: refurbished (used), machine/vehicle number: SN2120, EDM312MF30-SLM (second-live machine) Technical data: Adjustment travel: 450x300x300mm workpiece clamping table 820x400mm tank size 900x520mm filling height 300mm distance table/electrode holder 150/450mm workpiece weight max. 800Kg Dielectric max. 700l dimensions WxDxH 2700x1800x2350mm Machine weight 2500kg Iaedpfx Aajhtrdye Ijr Mains connection 3/N/PE 400/230 50Hz power consumption 6,7 KVA Equipment: Color: new painting light grey + telegrey New control cabinet New control APC910/2 (win10) User interface MF30 V 2.8 New drives B&R with Endat interface Screen touch screen Generator exopuls+ 60A Rev.4 WZW 5-fold Touch protection operable via push button Linear scales in all axes X, Y, Z (Fagor) cartridge filter 2 pieces Cooling unit Termogamma Complete new machine installation New ball screw, bearing, coupling Maintenance unit with digital pressure switch Valve island Co² extinguishing system C-axis Hirschmann 50/min., holding brake Refurbished Manual control bar with enabling button Lowering tank automatic tracking chuck Erowa IST, Hirschmann, 3R Warranty 12 months Transport commissioning on site training

Year of construction: 2014, condition: ready for operation (used), Clamping force: 1600kN, weight: 9t, operational hours counter: 3638h, with Handling Robot ENGEL viper 20. Iaedpfxjh Nypfe Aa Ior

Condition: excellent (used), functionality: fully functional, Year of construction: 2012, operating hours: 55,771 h, laser hours: 35,157 h, laser power: 3,200 W, sheet thickness (max.): 20 mm, sheet thickness steel (max.): 20 mm, sheet thickness aluminum (max.): 8 mm, table length: 3,000 mm, table width: 1,500 mm, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 150 mm, positioning speed: 140 m/min, positioning accuracy: 0.02 mm, year of last overhaul: 2024, feed length X-axis: 3,000 mm, feed length Y-axis: 1,500 mm, feed length Z-axis: 150 mm, Equipment: cooling unit, documentation/manual, safety light barrier, The laser is in operation, can be inspected and tested. Regularly serviced in good technical condition. Mirrors completely replaced in 2024. Isdpfx Aev Hxbbsa Iear

Condition: used, Year of construction: 2001, Technical details: x-travel: 2500 mm y-travel: 1000 mm z-travel: 750 mm table surface area: 3220 x 1000 mm Workpiece weight approx.: 3000 kg spindle taper ISO: 50 milling spindle turning speeds: 20 - 5000 U/min feed speeds: 1- 30000 mm/min rapid traverse: 30 m/min total power requirement: 40 kW dimensions of the machine ca.: 6,9 x 4,1 x 3,7 m Iaodpfxjvptmwo Aa Ier weight of the machine ca.: 21 t with CNC HEIDENHAIN TNC 426 30-pockets autom. toolchanger RENISHAW measuring probe coolant attachment with TSC and chip conveyor diverse toolholders *