Chipper with magnetic conveyor belt.

Votecs EZ 10- 2

Condition: excellent (used), Year of construction: 2020, Hacker slow-speed shredder with powerful 45 kW motor, ideal for cables, plastics, and pallets. Rotor width: 1000 mm, rotor diameter: 368 mm. Fitted with 56 large knives (40 x 40 mm). Motor: 45 kW. Can be purchased with or without discharge conveyor (with overbelt magnet). Nodpfoykzy Esx Adtjla

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Nodpfxswp Rqfe Adtola Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: excellent (used), Year of construction: 2020, Powerful hacker or shredder with 45 kW motor, also suitable for plastic. Rotor width: 1000 mm, rotor diameter: 360 mm, approximately 50–60 blades on the rotor. Inclined conveyor belt with magnetic roller available separately. Nodpfx Aew Tdudedtjla

Condition: used, Year of construction: 2003, operating hours: 10,120 h, total length: 1,800 mm, total height: 1,700 mm, total width: 1,200 mm, Empty weight: 1.300 kg Price: On request Shredder Untha LR 630 Nsdpswh Na Nsfx Adtela Year of construction 2003 Input opening: 624 x 792 mm Throughput speed: material and sieve dependent Rotor diameter: 248 mm Rotor speed: 86 - 96 rpm Engine power: 15 kW Cutting system: 17 knives Sieve diameter 24mm Transport dimensions 1800*1200*1700mm (L*W*H), Weight 1300kg - Year: 2003 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: LR632318 - Operating hours: 10120 - Transport dimensions: 1800mm x 1200mm x 1700mm (l x w x h) - Transport weight [kg]: 1300kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Year of construction: 1998, condition: excellent (used), NEUE HERBOLD cutting mill / granulator Universal mill - heavy version Made in stainless steel Njdpfx Ash Rwc Eedtela -Year of construction 1998 - made of stainless steel - from technical center (machine was used exclusively for test/demonstration purposes - Rotor diameter: 300 mm - Working width: 500 mm - 3 rows of knives

Condition: new, Year of construction: 2024, Chopper Knife 40 x 40 concave Nodpfxobxu Dhe Adtjla Knife for Weima, Large ..... For almost all common chippers / shredders From stock Bitburg Subject to prior sale

Condition: refurbished (used), Completely refurbished Bongioanni CRL 4 tensioning wagon with clamping blocks. Track gauge 1200 mm. Rails newly milled. Servo-electric drive. Sale upon customer order. Nlsdpfx Adextwxbotoa

Condition: reconditioned (used), functionality: fully functional, approx. 4.5 m long infeed and centering table Drive via chain from the feed motor Centers the logs in the middle of the rotor Debarking machine VK 26 4 main cutters 4 pre-cutters 30 KW main motor 11 KW feed unit non-driven extraction table Machine workshop checked Machine cleaned and repainted Nlsdpfx Aou Hmacjdtja

Condition: new, power: 90 kW (122.37 HP), Year of construction: 2026, A double rotor hammer crusher is a type of crusher in which two rotors are mounted on a single shaft, combined to form a spinning rotor. The double rotor arrangement enhances the crushing capabilities and provides a more efficient and reliable crusher design compared to single rotor crushers. Here are some key features and aspects of a double rotor hammer crusher: 1. Two Rotors: As the name suggests, the crusher has two rotors that rotate in opposite directions on a common shaft. This dual rotor configuration allows for increased impact and crushing power. Nledpfx Adjq Nf Enstea 2. High Capacity: The dual rotor design enables the crusher to handle larger feed sizes and higher capacity compared to single rotor crushers. It is suitable for crushing materials with high hardness and large sizes. 3. Versatility: Double rotor hammer crushers are versatile and can be used in various applications, including the reduction of limestone, gypsum, coal, and other similar materials in the mining, cement, and building materials industries. 4. Impact Crushing: The primary mechanism of crushing in a double rotor hammer crusher is through the impact of the hammers against the material. The material is fed into the crusher, and the high-speed rotating hammers impact and shatter the particles. 5. Adjustable Gap Settings: These crushers often have adjustable gap settings between the rotors and the impact bars, allowing control over the final particle size. 6. Durability: The robust design of the double rotor hammer crusher makes it durable and capable of handling tough materials and continuous operation. 7. Reduced Wear: The dual rotor arrangement can help distribute wear more evenly across the hammers and other wear parts, potentially extending the overall lifespan of the crusher. Typical Technical Specifications While exact numbers vary by manufacturer, these are the standard ranges for industrial models: Model (Rotor Size),Max Feed Size,Output Size,Capacity (t/h),Total Motor Power 600 × 400,≤110 mm,≤3 mm,10 – 15,18.5+18.5 kW 800 × 600,≤120 mm,≤3 mm,40 – 50,45+45 kW 800 × 800,≤180 mm,≤3 mm,50 – 60,45+55 kW 1000 × 800,≤180 mm,≤3 mm,70 – 80,75+55 kW 1100 × 1000,≤200 mm,≤3 mm,70 – 100,90+110 kW 1400 × 1200,≤200 mm,≤3 mm,90 – 110,132+160 kW For more details about double stage hammer crusher, or double rotor crusher, welcome to leave us a message, our team will get back to you at the earlist.

Condition: new, Year of construction: 2024, carrying capacity per cantilever arm: 500 kg, shelf height: 3,200 mm, total length: 2,100 mm, total height: 3,200 mm, axle spacing: 1,000 mm, load capacity per stand: 2,500 kg, Cantilever rack in hot-dip galvanized design: Scope of delivery: 3 rack stands, height 3.2 m with base section, 1.8 m usable depth (2 m total depth) 12 cantilevers with 1.8 m usable depth (for chipboard with approx. 2.1 m depth) Longitudinal and diagonal struts for 4 m rack length (distance 1.3 m) Fastening material (screws, nuts and washers) Net price: €2,490.00 plus VAT Detailed description: - Stable steel construction made of IPE profiles (screw system) - Rack height 3,200 mm - Load capacity per stand 2,500 kg - Base section and cantilevers with 1,800 mm usable depth - (for 2,100 mm chipboard depth) - Cantilevers height adjustable in 100 mm increments - 4 screwable screws per stand Cantilever arms, standard (= 5 storage levels) - Load capacity per cantilever arm 500 kg - Including longitudinal and diagonal braces for 1,000 mm spacing - Shelf length = 2,100 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Made in Germany - Short delivery time Our cantilever racks are produced exclusively in Germany. Nlsdpfoqt Dmysx Adtsa We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. Delivery for stock items can take place in approx. 1 week after receipt of the order. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.