Concrete Block Machine

ZİM Mühendislik ZIM 8

Year of construction: 2022, condition: new, This system operates in automatic mode. The transfer of pallets between production line and curing area is carried out by Finger Car. 1 operator supervises the production process via control panel equipped with 4 different monitor, pc system. Automation system software has user-friendly interface and can be translated into customer’s preferred language. Production line requires the construction of curing chambers with racks. Steam curing is recommended for working in one shift and is mandatory for working in two shifts. Ijdjibcycjpfx Ah Uotr Transfer of production pallets with green products to the curing chambers as well as the transfer of pallets with cured products to the cubing station is carried out by automatic pallet transport system known as Finger Car. Finger car consists of lower and upper electric trolleys, which move along a set of rails built perpendicularly to the concrete block production line. The upper trolley has steel forks for grabbing and holding pallets. It transfers concrete products to the curing chambers, going inside each chamber to place pallets with wet products on racks to cure. On its way back it takes a stack of pallets with cured products and loads it into the lowerator. The price given as 1.200.000 USD includes all the machine equipments, concrete batching plant and 3000 pallet rack system. It is very special offer for August 2022!

Condition: excellent (used), Year of construction: 2009, Used Bottling Line | Used Beverage Line | Soft Drinks NP 602 | PET BOTTLING LINE 12,000 BPH Speed: 12,000 Bph Blow molding machine SIPA Year: 2009 Number of cavities: 8 Preform elevator Preform orientator Chiller Formats of 05 L - 1 L - 1.5 L Monoblock TETRA PLAST RFA-40 Year: 1995 Filling type: aseptic Cap type: prethreaded plastic 38mm Caps elevator Dryer EUROPOOL Year: 2007 Type: air blades Labeling machine KRONES Type: roll-feed Sleever machine CLEVER 2019 With Steam Tunnel Bottle rejection system FMT dryer Year: 2011 Type: air blades SMI Bundler Year: 2009 Ijdpfx Ahjtqfcgo Uetr TWIN PACK handle applicator Year: 2000

Condition: good (used), POLY CLIP FCA3462 AUTOMATIC CLIPPER The POLY CLIP FCA3462 automatic clipping machine is designed for closing all types of casings (including protein casings) with a caliber of 40 – 115mm. PARAMETERS: * automatic device for cooperation with all types of stuffing machines equipped with a portioning machine * automatic loop feeder * stuffing expander (clipping protein casings) * automatic loop feeder * electric strip that discharges bars * electrical and mechanical connection with the stuffing machine * movable, pneumatic brake * string feeder ( clipping ring sausages) * casing end sensor * clipping speed: three speeds, maximum speed 90 tacts/min * pneumatic supply 6 bar DESCRIPTION OF OPERATION: The clipper is mechanically and electrically connected to a stuffer equipped with a portioning machine. At the beginning of the work cycle, a casing is put on the funnel of the clipper, and then the operator starts clipping the beginning of the casing. Then, after pressing the start button, the stuffer performs the set portion, after which automatic clipping takes place. Further work is carried out cyclically. PRODUCER: Poly Clip MODEL: FCA 3462 Ijdpstr Ux Eefx Ah Ustr TYPE: Automatic clipper POWER: 400V HEIGHT: 190 cm WIDTH: 150 cm LENGTH: 150 cm WEIGHT: 620 kg MATERIAL: Stainless Steel

Condition: used, mileage: 117,898 km, Year of construction: 1978, Serial number: 100xxxx Please contact ATS Norway for more information Please provide reference number upon request: 21424 Specifications: 1978 model 117,898 km Rep. Object 205 hp 6x2 Manual transmission Tires (see pictures) Rust of the rear housing (see pictures) Frame sand blue and varnished a few years ago Battery needs to be replaced. Tipping box Foldable aluminum limbs Internal length in plan: 6,115 m Internal width in plan: 2,475 m Light Heater Ready for delivery   Crane specifications: 1979 model 10 t/m crane 2 Hydraulic outriggers Itjdpfxoxgcrge Ah Usr 2 Hydraulic extensions 1 Hydraulic extension on main boom 1 Manual Manually controlled Ready for delivery   Description: We have a 1978 Scania LB 81 6x2 Crane truck w/ 10t/m crane and tipper ekt for sale. The car is being sold as a repair item as it is no longer EU approved and there are errors and defects. There is a bad battery on the car, these should be replaced. Starter is starting to get bad. Errors and deficiencies exist and some cost must be taken into account to get it back in good condition. Ready for delivery Km: 117898 HK: 205 Technical approved: no EU-approved until: 28.02.2019 Own weight: 10100 Model: LB 81 6x2 Kranbil m/ 10t/m kran og tipp ekt Gearbox: Manual

Condition: not inspected (used), Year of construction: 1984, Turning length max. 1200 mm turning Ø max. 250 mm 2 hydraulic scanning supports spindle motor 5,5 kW Iodpjp Dt Twsfx Ah Ujtr hydraulic motor 2,2 kW

Year of construction: 2022, condition: new, ZIM T 1210 machine is designed to increase efficiency for production of manholes, conics and rings. It’s production capacity is very high when you compare with the ordinary machines. It has uniqe specifications to increase production capacity, using life, products quality. This machine can produce pipes 300mm – 1200mm diameter and 1000mm height. Machines can be designed semi or full automatic according to requirements. We use SIEMENS brand PLC microprocessors on automatic machines. There is mortar bunker and mortar filling cart on machines. We use inner filling system for mortar filling cart and it makes equal and fast filling to moulds. Production is done on production pallets, This production pallets should wait till the products dry and it takes around 24 hours if there is no curing system. The vibration system of machine is controlled by frequency driver controll system. It does not need any mechanic settings. It can easily adjusted from operator pannel. The vibrator system specially designed by our R&D team is used in our machines. The cooling of the vibrators are done by oil cycle system. There is a special unit for that cycling process. Oil flow is controlled by special sensors. Thanks to this technology our machines which have been working for many years without any problems, stand out with their low operating costs. Itedpfxeirtdpe Ah Usr Special designed strong chassis of the machine enables long life production without errors. Produced materials can be carried to drying area with carriage carts or forklifts. The products can be carried to drying area with carriage carts or forklifts.

Condition: new, Year of construction: 2025, COMPACT CONCRETE BATCHING PLANT C60 SNG PLUS GENERAL Plant Type : Compact Concrete Plant with Single Shaft Mixer Plant Capacity : 60m³/hour freshly compressed concrete Mixer Capacity : 1500/1000 lt (1m³ Compressed Concrete) Total Motor Power : 85kw Standard Value can be changed depending on Equipment.. Voltage/Frequency : 380V/50Hz Standard Value. A very low transport cost : ONLY ONE CONTAINER/TRUCK The installation and startup of the plant is under our responsibility. We provide excellent after-sales service. 24/7 SERVICES. REMOTE CONTROL SERVICE. Exporting more than 700 Concrete Batching Plants to more than 60 Countries all over the world. Itedpfx Asflz Hdeh Ujr * LOW SHIPMENT COST(just ONE 40F-OT container or ONE standart trailer) * QUICK INSTALLATION * EASY AND SIMPLE USE DETAILS: Compacted concrete capacity: 60 m³/h Air Compressor Capacity : 650 lt/min Aggregate Hopper : 4X10 (40 m³ ) Mixer Type : SINGLE Shaft (1 m³). 1500/1000 lt capacity Aggregate Transfer Belt : 800x12.000 mm. Weighbridges: Aggregate/ Cement /Water/ Additives OPTIONS: *Cement Silo: 75-100-150-200-500 tons *Cement Silo Equipment and Screw Conveyor. Central Lubrication System Brand : ILC (made in italy) Mixer body Plates : Manganese (it can manufacture 50.000m3-450.000m3) Mixer Internal Linings (Wear Plates) : Ni- hard special hard cast material Discharging in Emergency Situations : manual Emergency Situation hand pump Emergency Stop Button available. Digital Mixer Control System (alarm) Automatic lubrication system monitor feature on pc Control System: Full automatic pc - plc – printer. Unlimited users Remote access Unlimited prescriptions and customer registration Retrospective reporting English- Russian- French- Arabic-German-Spanish languages are available. Switching materials used in the MCC dashboard are SIEMENS Back off available.

Year of construction: 2022, condition: new, ZIM T1200 machine can produce pipes 300mm – 1200mm diameter and 500mm – 2500mm height by single, double and triple pressing. 150mm and 200mm pipes also can be produced for special demands. Machines can be designed semi or full automatic according to requirements. Itodpfx Ajibbikeh Usr We use SIEMENS brand PLC microprocessors on automatic machines. There exists motrar bunker and motrar filling systems on machines. Produced materials can be carried to drying area with carriage carts or forklifts. Production is done on production pallets, Materials up to 800mm diameter are carried to drying area with carriage carts, pipes bigger than 800 mm diameter can be carried with forklift. For fast production, pipes bigger than 300mm diameter also can carried to drying area with forklift. Machine makes production by hydraulic press and vibration. Vibration system of the machine is special design of ZIM Engineers. Vibration system which have oil cooling system and special oil unit. This system can be controlled electronically. Special designed strong chassi of the machine enables long live producing without errors.

Condition: like new (used), Completely made of special stainless steel Specialized for grinding cheese and yellow cheese BLOCKS Hole plate diameter: 200 mm Hopper capacity: approx. 400 liters Synchronized speed for shatter and feed screw Working worm Machine dimensions in сm: Width: 215,0 Ijdpspgnftsfx Ah Uetr Depth: 150,0 Height: 196,0 Main Motor Power: 45 kW Installed Power approx. 65 kW Voltage: 380 V, 50 Hz

Condition: used, functionality: fully functional, Year of construction: 2009, machine/vehicle number: 1017, Used production line for blocks of concrete (and expanded clay). The line was used to produce concrete blocks using expanded clay. From 2023-08, the line is no longer in operation, it has been preserved. Line of blocks in order: - 2 pcs. small silos (with vibro, with pneumo flaps). - Raw material supply conveyor to the weighing hopper. - Weighing hopper. - Raw material supply conveyor from the weighing hopper to the mixer. - Mixer FK Machinery (Poland, 2022, bucket capacity 1200 l, engine power 18.5 kW). - Conveyor for feeding the mixture from the mixer to the SIGMA 1000 vibro press. - Vibro press SIGMA 1000: Type mark: PIERRE ET BERTRAND SIGMA 1000 with automatic TELEMECANIQUE control Manufacturer: ADLER S.A.S. Route de la Bourde, 60360 CREVECOEUR LE GRAND, France Serial no./year of manufacture/year of renovation - 1017/1989/2009 Area on the board (palette): 1130 mm x 550 mm (long x wide) Height of products - max 250 mm - Production shelf. - From the production shelf, the production is transported by autoloader to the mechanism where the production is automatically reloaded from the production boards onto the pallets. Production boards are automatically returned to the vibro press. Itsdpfx Asuc Tzvsh Uor - Control board with programmer. - Electric switchboard. 2022 year of production Mold 200 x 185 x 490 with which we have been working for the last year. There are many other used Moulds. There are about 500 pieces production boards. There is no compressed air compressor. We can provide disassembly, assembly and equipment startup services.