Press container

Aventek RM20

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, functionality: fully functional, pressing force: 70 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 500 kg, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Bedpfx Asu Thbxjczodk Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Drive power 4.0 kW Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Year of construction 2023 Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2025, container length: 3.6 ft, color: white, overall weight: 600 kg, maximum load weight: 600 kg, empty load weight: 600 kg, loading space volume: 3.4 m³, loading space width: 1,100 mm, loading space length: 1,200 mm, loading space height: 2,600 mm, machine/vehicle number: Sanitärcontainer WC, Equipment: bathroom, Sanitary container | WC container | Shower container | Toilet container | Double WC container | 110cmx120cm | Model WC | High-quality and flexible solution Available products can be viewed in our warehouse and picked up directly. Our office and residential containers offer an excellent solution for a variety of applications. They are characterized by outstanding quality, maximum flexibility and short delivery times. Technical details: Dimensions: • Length: 120 cm • Width: 110 cm • Height: 260 cm • Weight: 400 kg Insulation: • Ceiling/wall: 6 cm PUR (polyurethane) • Optional: 10 cm insulation with PUR, PIR or rock wool available • Floor: 16 mm fiber cement board • PVC covering Equipment: • 1 room • 1 external door • 1 toilet with washbasin • 1 ventilation Colors: • Facade color: RAL 9002 • Frame color: RAL 9002 • Customization: Individual design possible according to customer's wishes Bodpjvxht Refx Aczjdk High-quality workmanship for long-term use Stock & delivery: • In stock: Same day shipping • Not in stock: Production time 2 to 4 weeks depending on model • Worldwide shipping: We offer professional shipping to all countries to ensure fast and reliable delivery. • Individual dimensions: Products can be manufactured according to the customer's specific requirements. Showroom address: Im Mannenberg 9a, 53557 Bad Hönningen We are happy to assist you with further information or tailor-made adjustments!

Year of construction: 2008, operating hours: 40,000 h, condition: good (used), machine/vehicle number: HBC 140 2x75kW 2008 (00191), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Bdedpfxekcgf Hs Aczjk Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: excellent (used), Year of construction: 2010, Material Testing Machine: ZwickRoell GmbH mod.Z005 TN Designed to perform standard tests on materials and components, allowing for precise measurements of strength, flexibility, and other material properties, which are crucial in engineering and material research. With advanced technology and intuitive software, these machines offer efficient and safe operation. The device includes accessories for measuring material tensile strength, compression, and bending. Technical Specifications: • Year of production: 2010 • Maximum load (Fmax): 5 kN • Test dimensions: - Height (without accessories): 1070 mm - Stroke height: 1000 mm • Frame dimensions: - Height: 1340 ... 1345 mm - Width: 770 mm - Depth: 439 mm • Weight: approximately 110 kg • Power supply: 230 V, 1Ph/N/PE, power consumption about 800VA Bdedsuna Iuopfx Aczok The machine allows for the testing of various materials and components, including: • Construction materials: concrete, steel, wood • Plastics: flexibility, tensile strength • Metals: strength, hardness, and fatigue testing • Mechanical components: compression, bending, and tensile tests • Samples in various forms: thin-layered, block-shaped, tubular Thanks to the system's flexibility, tests can be adapted to specific requirements. TAG: Laboratory Equipment, Material Testing, EPS Styrofoam, Polystyrene Production, Mechanical Testing, Thermal Conductivity, Material Properties, Construction Materials, Quality Control, Engineering Research

Condition: new, Bunker conveyor suitable for the feeding of presses, shredding, etc.. Delivery throughout Europe possible. Bedpfedxwlqex Aczedk Technical data: POS. 1 feed hopper POS. Task 2, vol. 1, 5kW, conveyor width: 1100 mm, axis dimensions: 3500 mm POS. Platform 3, volume 1, 1kW, conveyor width: 1100 mm, axle size: 4700 mm Standard discharge height: 2800 mm (greater than possible with distance feet as shown on the illustration) Ordering goods Further information and data upon request

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Bdedpfx Asu Thhreczok Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2025, functionality: fully functional, total width: 2,400 mm, total length: 15,000 mm, total height: 2,800 mm, pressure: 8 bar, power: 10.9 kW (14.82 HP), empty load weight: 6,400 kg, input voltage: 400 V, filling weight (min.): 200 g, filling weight (max.): 5,000 g, XFR 1000 Liquid Media Filling Line A fully automated liquid media filling line featuring robotic capping, automated handle placement, dual-sided labelling, optical quality control, and pallet wrapping. An end-to-end solution covering the entire process, from bottle blowing to the palletizing and wrapping of filled bottles. Bodpeuq Nv Tefx Aczjdk XFR LIQUILOAD It enables optimal filling speeds for bottles of varying characteristics and liquids of different viscosities. The machine’s easy configuration for different bottle types and corresponding liquids ensures quick adaptation to market demands. • Capability to increase the number of nozzles • Nozzles designed to prevent foaming of the liquid • 800 to 4,000 filled bottles per hour • Servo-driven nozzle positioning • Easy configuration of new programs XFR BOTTLELOCK The machine segment performs fully automated capping of filled bottles. Designed to accommodate various cap types, simplifying machine adjustments for seamless operation. • Cap type adaptability • Robotic bottle capping • Optical inspection • 800 to 2,000 capped bottles per hour XFR HANDLEGRIP The automatic robotic placement of handles on bottles, while they move continuously towards the labeling machine, ensures seamless and uninterrupted operation. • Adaptability to different handle types • Robotic handle application on bottles • Optical inspection for handle orientation verification • Capability to attach handles with a funnel XFR LABELFLOW The machine applies the appropriate labels to both sides of the bottle, creating a finished appearance. In the next phase, the labelled bottles undergo optical inspection. • HERMA labelling system • Simplified label type changeover • Servo-driven for enhanced labeling precision • Monitoring of remaining labels with operator alerts OPTIONAL PARTS: 1. OPTICAL INSPECTION Industrial cameras with integrated lighting and pneumatic ejection system. 2. PICK AND PLACE ROBOT 6-axis robot equipped with a 160 kg gripper for the current handling of 8 bottles onto a Euro pallet. 3. PALLETIZING Palletizer with automatic pallet feeding via a roller conveyor to the bottle stacking area. 4. PALLET WRAPPING The automatic pallet wrapper applies stretch film to palletized products, securing them for easier and safer transport. 5. FINISHED GOODS STORAGE Finished pallets are transported to the warehouse via a metal roller conveyor. 6. REMOTE CUSTOMER SUPPORT We provide remote support to ensure optimal machine performance. 7. ADDITIONAL OPTIONS Automated data integration with ERP systems; RFID login; NFC detection of parts and tools; magnetically mounted tools. 8. MACHINE CONFIGURATION Segments can operate independently or as an integrated solution, depending on the client's specific needs. Proton EE-Elektronika d.o.o. MachinFlex d.o.o.

Year of construction: 2024, condition: new, The JC 500 jaw crusher is ideal for crushing hard, brittle, hard-tough samples such as ceramics, clinker, coke, building materials, ferroalloys, glass, minerals, ores, precious metals, rocks, silicon, slag and much more. Bdodsiamq Hepfx Aczsk

Condition: used, Year of construction: 1996, Year: 1996 / overhauled in 2008 Bodsxfvrwepfx Aczedk Technical specifications and equipment: • 8 printing units Material width: 620 mm Printing width: 600 mm Print repeat lengths: 250 – 520 mm Materials processed: • PA: 20 – 60 µm • LDPE: 20 – 150 µm • HDPE, OPP and similar films: 12 – 80 µm, max. 120 µm • Laminated films • Paper: 25 – 120 g/m² Mechanical machine speed: up to 200 m/min (depending on substrate) Main equipment: • Impression cylinder with new nickel-plasma coating • Impression cylinder temperature control unit • Non-stop unwinder with web tension measurement and control, including splice table, roll diameter 600 mm, core ID 76 mm • Nip roller before 1st printing unit • 8 doctor-blade printing stations • Speed assist system • Drive elements from the printing unit to the bridge • Intercolor dryers • Web guiding before printing • Bridge with bridge dryer • Web video inspection system • Edge guiding before rewinding with 3 slitting discs and suction • Non-stop rewinder with pneumatic slitting and web tension measurement and control, roll diameter 600 mm, core ID 76 mm • 8 chamber doctor blades plus 8 additional coated doctor blades • 8 electric pumps, new • 8 ink vessels (10 L each) with hose connections, new • 8 ink catch trays plus 4 extra trays • 1 service trolley for anilox roll and sleeve handling • 1 service trolley for chamber doctor blade and ink tray handling • 8 printing sleeves, new, print length 320 mm, make: Rotec Conductive Blue Light • 8 format gears, new, print length 280 mm • 8 ceramic anilox sleeves, new. Base bodies ordered from Apex. Company Wareg will obtain required sleeve type directly from Apex; only for UniFlex sleeves will Wareg incur the additional costs. • ATEX-compliant • New Siemens S7 control system

Condition: used, Year of construction: 2018, operating hours: 9,900 h, * Volvo EC220 EL crawler excavator * Year of manufacture 2018 * 9900 h * 25100 kg Bodpfx Acsvvfx Eozedk * 129 KW Volvo engine * Automatic air conditioning * Construction machinery technology hydraulic quick changer * Hydraulic bucket 160 cm * 180 degree camera * LED package * Track width 300 cm * Chain plates 60 cm