Used lowboy semi-trailers / low loaders for sale (204)

Condition: new, maximum load weight: 36,461 kg, overall weight: 49,500 kg, axle configuration: 3 axles, total width: 2,480 mm, total height: 860 mm, Year of construction: 2026, Technical Description Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). 30 mm thick hardwood flooring. Loading Platform: Loading platform behind the gooseneck hydraulically liftable and lowerable, length approx. 2,800 mm, with rear bevel of approx. 1,000 mm x 8°. 6 pairs of outward-folding lashing rings (LC 5,000 daN). 2 pairs of outward-folding lashing rings (LC 10,000 daN). 1 pair of inward-folding lashing rings on the front central beam (LC 10,000 daN). Grating flooring C40/4 (point load 2.3 t on an area of 20 x 20 cm), over the axles with chequer plate covering. Two-Part Steel Ramps: One pair of galvanized, two-part steel ramps approx. 3,185 + 1,420 x 1,250 mm with grating flooring C40/5 (point load 8 t on an area of 20 x 20 cm). Ramp with hydraulically foldable ramp sections and hydraulic lifting system. Maximum load per pair: 40,000 kg In accordance with regulation 1230/2012/EU, ramps less than 300 mm in length do not count towards the vehicle length of 16,500 mm in driving position. Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: Tyres 235/75 R17.5 3PMSF as per manufacturer’s choice. TPMS: TPMS tyre pressure monitoring system as per ECE R 141. Data transmission to the tractor unit via the standardized EBS interface according to ISO 11992. For correct display, the tractor unit must be able to receive and display these data. Axles: BPW axles and suspension, 2 fixed axles, 1 self-steering trailing axle. Technical axle load: 12,000 kg Electromagnetic reverse lock, activated via reverse gear and manually. Air suspension with raise and lower valve. Axle tools included. Brake System: Lodpew Dl Hwsfx Ac Aohf WABCO braking system compliant with EU regulations with EBS-E (2S2M), without connecting lines to the tractor unit. Electrical System: Electrical system compliant with EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3). All LED side marker lights flash with the indicator. ASPÖCK-UNIBOX on the front connector strip with 24N, 24S & 15-pin sockets. Connection according to ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Structure: Steel frame made of high-strength fine-grain steels. Steel grades: – S355J2+N/S355MC (yield strength 355 MPa) – S690QL/S700MC (yield strength 690 MPa) Tarp Structure: Tarp structure approx. 3,960 mm – Galvanized front wall with a tensioning mechanism for the sliding curtains. – “EDSCHA” roof, forward-sliding on aluminum roof rail profiles (bolted to front and rear walls). – 3 pairs of movable stanchions on the loading platform. – Body can be hydraulically widened at the rear by approx. 750 mm to the left and right. – Sliding roof with upward-swinging portal carrier. – Sliding tarp with 700 mm length reserve and tensioning straps at approx. 600 mm intervals. Height to top edge of structure approx. 3,960 mm (loaded). – Driving with open sliding roof is not permitted and will cause damage to the tarp. Painting: Entire steel structure is automatically shot-blasted after welding using a blasting wheel system. Second blasting treatment with corundum for optimal coating adhesion. Full metallizing of the entire chassis with ZINACOR 850 (85% zinc / 15% aluminum) for best corrosion protection. Top coat with 2 layers of 2K finish, single-color in a shade of your choice according to the RAL 841GL standard. Rear section metallized and coated in RAL 9010 (pure white). No metallic paint.

Condition: new, maximum load weight: 36,156 kg, overall weight: 45,000 kg, axle configuration: 3 axles, Year of construction: 2026, MAX200-N-3A-13.60-19.5-2.54 Technical data Speed: 80 km/h Total weight: 45,000 kg Fifth wheel load: 18,000 kg Lhsdeg Sk Tvepfx Ac Aof Axle load: 27,000 kg Empty weight (+/- 3%): 8,844 kg Payload approx.: 36,156 kg Loading area length: 13,600 mm Fifth wheel height loaded: 950->1,050 mm Rear steering radius: 2,300 mm Extendable by: 3,400 mm Axle spacing: 1,360/1,405 mm Total width: 2,540 mm Technical description Loading area: Loading area in extendable design with pneumatically operated locking. 2 pairs of lashing rings (LC 5,000 daN). 1 pair of lashing rings (LC 10,000 daN). 6 pairs of lashing rings that can be folded outwards (LC 5,000 daN). 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN). Cut-outs in the outer frame of the loading area for hanging tensioning straps. (LC 2000 da N) Seat supports: JOST seat supports (mechanical) with 2-speed gearbox for 24t lifting load (50t test load). Axles: SAF axles: SAF axles CD, air-sprung, with disc brakes (377 mm), with lifting/lowering function. (ET 120). The self-steering axles with electro-magnetic reversing lock can be activated via reverse gear or manually. Axle tool. (± 80kg) Braking system: Braking system in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit. Steel construction: Steel construction made of high-strength fine-grain steels. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) top coat in a single color in RAL colors of your choice. Rear section metallized and painted in RAL 9010 (pure white). No metallic paint possible. Electrical system: Electrical system in accordance with EU regulations, lighting LED 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection panel with sockets 24N, 24S & 15-pin. Connection in accordance with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included Yellow-red air couplings on the galvanized front connection panel. 2 pieces of brake shoes with holder. 2" kingpin A galvanized steel bulkhead approx. 2200 mm high. (± 105kg) EN12642-XL Yellow reflector tape in accordance with EU regulations on the side, on the extension and at the rear of the trailer. European reflector signs (red-yellow) on the rear of the trailer. Loading area with approx. 38 mm thick hardwood floor. (± 320kg) 10 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area. (± 30kg) 1 spare wheel holder under the loading area on the right in the direction of travel. Tires 435/50 R 19.5 as selected by the manufacturer. A mud flap ( ) on the rear of the trailer. Manual and description on USB stick. A bracket for a rotating beacon on the rear of the trailer. One bracket for a rotating beacon on the gooseneck and on the rear panel on the left and right the warning signs including a socket. An INOX toolbox across the loading area. (1000x400x2500) (± 135kg) 6 pairs of WADER container pockets in the loading area, for 1x20' container, 2 x 20' container or 1 x 40' container, an additional locking point is provided in the pull-out for a 45' container. (± 90kg) 4 pairs of WADER container locks. (± 60kg) 10 pairs of galvanized plug-in stanchions approx. 100 x 50 mm, 1,000 mm high. (± 220kg) 3 pairs of stanchion pocket strips, mounted across the loading area, for plug-in stanchion

Condition: new, maximum load weight: 44,000 kg, overall weight: 61,000 kg, axle configuration: 3 axles, Year of construction: 2026, Further information here: Lhjdpfxev D Abto Ac Asf

Condition: new, maximum load weight: 40,017 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, Year of construction: 2026, Technical Description Gooseneck: Gooseneck with rear chamfer of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). 30 mm hardwood flooring. Loading Platform: 5 pairs of folding external lashing rings (LC 5,000 daN). 3 pairs of folding external lashing rings (LC 10,000 daN). 1 pair of flat-mounted lashing rings at the front of the loading platform (LC 10,000 daN). Approx. 48 mm thick hardwood flooring, checker plate covering over the axles. Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: 205/65 R17.5 tyres as per manufacturer's specification. TPMS: TPMS tyre pressure monitoring system compliant with ECE R 141. Data transmission to the tractor unit via the standardised EBS interface according to ISO 11992. To ensure correct display, the tractor unit must be capable of transmitting and displaying this data. Axles: BPW axles, two fixed axles, two self-steering axles, air-suspended, with drum brake, with lifting/lowering function. The self-steering axles can be locked electronically via reverse gear or manually using an electromagnet. Axle tools included. Brake System: WABCO brake system in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit. Electrical System: Electrical system according to EU regulations, 24 volt LED lighting by ASPÖCK-NORDIK (ASS3). All LED side marker lamps flash with the turn indicators. ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets. Connections conform to ISO standards: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Construction: Steel structure made from high-strength fine-grained steels. Steel grades: – S355J2+N/S355MC (yield strength 355 MPa) – S690QL/S700MC (yield strength 690 MPa) Paintwork: The entire steel structure is automatically shot-blasted with a turbine system after welding. A second abrasive blasting treatment with corundum ensures optimal adhesion of the coating system. HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for superior corrosion protection. Final coating with 2 coats of 2K topcoat, single-colour in a shade of your choice according to the RAL 841GL system. Rear section metallized and painted in RAL 9010 (pure white). Metallic paint not possible. Paint system tested in salt spray test according to ISO 9227-NSS. Cavities sealed with special wax. Options included: 2" kingpin Lodow Dl Hqepfx Ac Ashf One galvanized steel bulkhead. Yellow-red air couplings on the galvanized front connection panel. 2 wheel chocks with holders on the bulkhead. Fixture at the rear of the gooseneck for ALU approach ramps. Further options upon request.

Condition: new, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2026, 3-axle MULTIMAX PLUS low-bed semi-trailer, air-suspended and hydraulically forced-steered axles. Technical Data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h Legal Gross vehicle weight: 49,500 kg / 31,500 kg Fifth-wheel load: 18,000 kg Axle load: 31,500 kg / 31,500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm King pin trailing radius (rearwards) approx.: 2,100 mm Saddle height loaded approx.: 1,205 mm Loading platform length approx.: 9,600 mm Extendable by approx.: ? Loading platform width approx.: 2,540 mm Loading height at max. load approx.: 890 mm Suspension travel approx.: -55/+145 mm Axle spacing: 1,360 mm Gross vehicle weight depending on fifth-wheel load: Yes Special permit is required for exceeding country-specific regulations. Technical Description Gooseneck: Gooseneck in SNT Design for optimized loading platform length, length approx. 3,900 mm, rear with chamfer approx. 1,000 mm x 6°. Technical fifth-wheel load: 18,000 kg. For tractor units: 4 x 2 and 6 x 2. Loading platform: Loading platform, length approx. 9,600 mm with rear chamfer approx. 900 mm x 6°. Loading platform behind the gooseneck hydraulically raisable and lowerable, length approx. 3,000 mm, loadable up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS A pair of two-part AXS steel ramps approx. 4,920 mm long and approx. 900 mm wide. Open grating surface. Hydraulically folding ramp tips. Ramps can be hydraulically shifted individually by approx. 235 mm outwards and approx. 365 mm inwards. Maximum load capacity and approach angle per technical data sheet: C470319 Maximum ramp angle with lowered loading platform: 9° Axles and Suspension: BPW axles and suspension, all axles hydro-mechanically forced-steered. Technical axle load: 12,000 kg Air suspension with lift/lower valve. Axle tool kit. Tyres: 235/75 R 17.5 3PMSF twin tyres. Manufacturer of our choice Load index 143/141J (144/144F) Braking system: WABCO EBS-E braking system according to EU regulations. Without connecting cable to tractor unit. Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" version as per EU regulations. (ASS 3) Metalizing: Complete HRM metalizing (High Resistance Metallisation) Complete steel structure shot blasted, then hot-finished with ZINACOR 850 (Zinc 85% - Aluminium 15%). Painting 6K final treatment: Complete steel structure shot blasted after welding. 1 coat zinc-based primer, 1 coat bonding primer. Lhsdpfxjizu Nte Ac Ajf Final painting with 2 coats 2K (acrylic) single-colour in RAL shades of your choice, then cavity sealing with special wax. Rims in silver. Multi-colour and special painting at extra cost. Steel construction: Steel structure made of high-strength fine-grained steels. Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders certified to DIN-EN 287-1. MAG welding process to EN ISO 4063. Protective gas M21 per EN ISO 14175 Front wall of steel, plug-in, approx. 400 mm high Connection board for supply lines to the tractor unit at the height of the outer frame profile. ASPÖCK-UNIBOX at the front plug connection board with sockets 24N, 24S & 15-pin. 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pin connection according to ISO-12098 If your pin configuration deviates from the ISO standard, please inform us. “Anderson” socket at the front connection board. Rema 78051-00 & Amp. 150 V. Cable for supply to electro-hydraulic unit and/or electric winch (35 mm²,

Condition: new, maximum load weight: 34,104 kg, overall weight: 47,000 kg, axle configuration: 2 axles, Year of construction: 2026, Further information here: Ledpfxov D Abgo Ac Ajhf

Condition: used, maximum load weight: 26,240 kg, overall weight: 36,000 kg, axle configuration: 2 axles, first registration: 10/2008, loading space length: 10,819 mm, Equipment: ABS, Manufacturer B-XL Lhodpfovl Dkrox Ac Aef Model 4.5 m. 2 axle extension Year 2008 Condition Good Serial Number WKVDAS00200021091 Ref. nr. 7721 Reg. date: 27-10-2008 Drum brake: ? ABS: ? Rear axles: SAF Suspension: Air Tire Size: 245 / 70R17,5 Cover% left 40 - 40% Total weight: 36000 kg. Net weight: 9760 kg. Steering rearaxle:?

Condition: used, empty load weight: 18,240 kg, maximum load weight: 45,760 kg, overall weight: 64,000 kg, axle configuration: > 3 axles, first registration: 02/2012, next inspection (TÜV): 01/2024, loading space length: 12,120 mm, loading space width: 2,740 mm, loading space height: 550 mm, tire size: 285/70R19.5, color: red, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 4 axles, SAF axles, forced steering, lifting + lowering, ABS (anti-lock braking system), lashing rings. Body: Low-bed trailer with 3 hydraulically steered axles and jeep dolly. Including a jeep dolly with a 10t SAF axle and 295/80R22.5 tires! At the rear: 3 x 12t SAF axles! Extendable to 3.2m width, 8m low bed platform! With radio and cable remote control, automatic self-alignment. A detailed technical description is available and can be sent by request! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to change, prior sale, and errors! Ledpeyf E E Ujfx Ac Aohf

Condition: used, maximum load weight: 19,080 kg, overall weight: 28,480 kg, axle configuration: 2 axles, first registration: 08/2025, next inspection (TÜV): 08/2026, CAUTION: To be operated only with tipping hydraulics! BPW 10t axles, 2 steering axles, CAUTION: To be operated only with tipping hydraulics! Fifth wheel height 1.25m, CAUTION: To be operated only with tipping hydraulics! Fifth wheel height 1.25m, hydraulic 1400x700 + manual 700, Lhodpjykgkcsfx Ac Asf

Condition: used, maximum load weight: 42,400 kg, overall weight: 64,000 kg, axle configuration: > 3 axles, first registration: 01/2011, Equipment: ABS, Goldhofer STZ-VLS4-37/80 and Goldhofer Dolly SX 1-25/80 - Height-adjustable low bed with removable gooseneck ----* Manufacturer: Goldhofer * Type: STZ-VLS4-37/80 * First registered: 01/2011 * Color: yellow * Total weight: 64,000 kg * Empty weight according to vehicle registration document: 21,600 kg * Axles: 4x BPW axles, of which 1st axle is steered via turntable steering, the remaining 3x axles are hydromechanical forced steering * Steering knuckle axles up to max. 45 degrees * Tires: 235/75 R17.5 approx. 70% * Suspension: Air suspension with lifting and lowering * EBS Wabco * Removable gooseneck with aluminum side walls * Hydraulic cylinders for support on the tractor unit * Toolbox with flap at the front of the gooseneck * Controls and pressure gauge on the left of the gooseneck * Gooseneck designed for freely rotating 1-axle dollies * Low bed for the chassis can be raised and lowered hydraulically * Chassis with excavator trough (starts from the 2nd axle) * Extendable widening of the loading area 440mm (2x 220mm) and 700mm (2x 350mm) * Wooden planks to bridge the gap between the widenings * Air suspension with raising and lowering to min. 825mm to 1,025mm (no driving position) * 2x fixed driving heights: * 1st driving height 925mm +100mm/-100mm * 2nd driving height 885mm +100mm/-100mm * 2 pairs of retractable lashing eyes in the gooseneck floor * 5 pairs of retractable lashing eyes in the low bed floor * 5 pairs of side lashing eyes on the low bed chassis * 4 pairs of stake holes in the low bed floor * 3 pairs of retractable lashing eyes in the chassis floor Lhedpfx Acsx Suzas Aef * 2 pairs of side lashing eyes on the chassis chassis * 2 pairs of stake holes in the chassis floor * 2x lashing eyes in the excavator trough * Rear of the vehicle sloped 10 degrees * 1-part hydraulic ramps (2,850mm x 720mm) and hydraulic supports at the rear * Operation of hydraulic ramps + supports at the rear left * Smartboard at the rear right * Additional LED reversing lights on the gooseneck and at the rear of the low loader * 1st hand German vehicle!! German papers!! 1st hand!! Goldhofer SX 1-25/80 Dolly ----* Manufacturer: Goldhofer * Type: SX 1-25/80 * First registered: 03/2011 * Color: Yellow * Total weight: 28,000 kg * Empty weight according to vehicle registration document: 2,750 kg * Axles: 1x BPW axle * Tires: 235/75 R17.5 approx. 70% / twin tires * 3" fifth wheel plate * Single fender * Supports * Loading manometer * 1st hand German vehicle!! German papers!!

Condition: new, maximum load weight: 43,929 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, loading space length: 16,690 mm, loading space width: 2,550 mm, total width: 2,550 mm, total height: 3,570 mm, Equipment: ABS, Kässbohrer K.SLA R 4 / 2N ? 18/40 Low Loader, Telescopic with Wheel Recesses (NEW) ----Equipment & Highlights Technology & Construction: - Extendable low loader with wheel recesses - Overall length: 13,190 mm, platform: 9,240 mm + 3,500 mm extension - Platform height: only 875 mm for low loading height - Total width: 2,550 mm + 600 mm extension - Unladen weight: approx. 14,071 kg - Gross vehicle weight: 58,000 kg (80 km/h) / 63,800 kg (60 km/h) Chassis & Axles: - 4 BPW axles, front 2 fixed, rear 2 self-steering - Lift axle (automatic + manual) - Air suspension with load gauge - WABCO EBS 4S/3M, ABS & RSS - WABCO Smartboard (axle load, suspension, diagnostics) - 16x tyres 245/70 R17.5 (M+S + 3PMSF) - Tyre pressure monitoring according to R141 Ramps & Loading Area: - Foldable 40-ton ramps - Ramp length: 2,750 mm, width: 850 mm - Hydraulic sliding system - 45 mm hardwood floor + steel chequer plate over wheel arches - Wheel recesses + covering bridges included - Digger arm recess at rear Load Securing: - Extensive lashing points: - 2×2 lashing rings 5,000 daN & 1×2 lashing rings 10,000 daN on gooseneck - 3×2 lashing rings 5,000 daN & 4×2 lashing rings 10,000 daN on platform - 8,000–10,000 daN on outer frame/wheel recess area - 5×2 stake pockets, removable stanchions 50×100 mm - Container locks for 1×20 ft or 1×30 ft containers Equipment & Comfort: - 1× tool box (700×400×360 mm) Lhsdpfx Acex Efznj Ajf - Stanchion box - Beacon light - LED side lighting, LED work lights - Wheel chocks - Width marker boards with LED - Standard 2" kingpin - Metallized chassis (Zn/Al 85/15) – high corrosion protection - Colour: RAL 9005 Black ----Special features: - New & immediately available - High payload, extremely flexible application - Perfect for machinery transport, construction equipment, vehicles, etc. - Very robust construction, high-quality BPW components For further information, we are at your disposal.

Condition: used, axle configuration: 3 axles, first registration: 04/2015, suspension: air, tire size: 445/45/19,5, color: blue, Year of construction: 2015, Equipment: ABS, Krone mega semi-trailer 2015 cover uncover raise lower new tarpaulin fixed axles Lsdpeqmnrxsfx Ac Ashf

Condition: used, axle configuration: > 3 axles, first registration: 05/2008, * Extendable * Self-steering rear axle * Hydraulic loading ramps * Air suspension -----Internal vehicle number: 11555----Subject to errors and prior sale WhatsApp support available! If you have questions about the vehicle or need further information, feel free to contact us conveniently via WhatsApp. Ljdpjx I Uyhjfx Ac Ashf WhatsApp: German, English -- WhatsApp: German, English, Arabic

Condition: new, empty load weight: 5,500 kg, overall weight: 19,500 kg, axle configuration: 1 axle, loading space length: 11,800 mm, loading space width: 2,550 mm, loading space height: 1,100 mm, suspension: air, tire size: 215 75 17,5, Equipment: crane, 1x SAF or BPW axle Total weight: 19,500 kg Payload: 14,000 kg Empty weight: 5,500 kg Total length: 12,800mm + 1500mm Brake system: Wabco 2S-2M Electrical system: Aspöck Systems Lhodpfxokqmuuj Ac Aof Air suspension Hydraulic rear extension in full width 2550mm and length 1500mm Semi-trailer completely galvanized / galvanized (100% galvanized / 100% galvanized) Tire size: 215/70 R 17.5 Tire brands: Pirelli, Goodyear, Fulda, Continental. 5th Wheel Height: approx. 1050mm - 1150mm (other saddle heights also possible) Hydraulic winch 8ton with remote control with pulleys 24v 4.5KW electro-hydraulic motor Steel ramp: 2 pieces Changes possible according to customer requirements Painting freely selectable / free of charge All documents COC, Tüv, etc. available for approval.

Condition: used, maximum load weight: 31,300 kg, overall weight: 42,000 kg, axle configuration: 3 axles, first registration: 02/2019, loading space length: 13,600 mm, loading space width: 2,480 mm, loading space height: 3,050 mm, total width: 2,550 mm, Equipment: ABS, Meusburger MPG-3 Low Loader Tarpaulin with Steering/Lift Axle Equipment: Air Suspension * Axle Balancer * 1st Axle Lift Axle * 3rd Axle Steered * Hydraulic Ramp with Additional Support & Radio Remote Control Ljdpewfwd Dsfx Ac Ashf * Drive-Through Ramp * Electric Cable Winch with Radio Remote Control * Edscha Roof * Storage Compartments on Both Sides * Spare Tire in Standard Tire * Additional Headlights * Extendable Wide-Width Side Panels Safety: ABS * EBS * Disc Brakes Subject to error and prior sale. Internal Vehicle Number: 8303

Condition: new, maximum load weight: 37,820 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our entire vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Full equipment details available upon request. Gooseneck: - Gooseneck with beveled front corners approx. 45° and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood floor covering approx. 30 mm thick Loading area: - 1 pair of fixed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) - Wheel recesses with square climbing slats approx. 15 x 15 mm and widenings in the lower section - Between the 1st and 2nd axles, a pair of fixed wheel recesses, approx. 1,610 x 700 x 400 mm (L x W x D) - Incl. 3-piece removable galvanized covers over the wheel recesses (W approx. 670 mm) – max. point load approx. 5 t/each - Recess in the chamfer and extending into the loading area for receiving the excavator bucket arm (approx. 2,900 x 750 x 210/290 mm (L x W x H)) - 1 pair of lashing rings, horizontal, at the front of the loading area (LC 10,000 daN) - 5 pairs of flip-out lashing rings (LC 5,000 daN) - 3 pairs of flip-out lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator arm recess (LC 5,000 daN) - Cut-outs in the outer frame of the loading area for securing straps (LC 2,000 daN) One-piece Steel Ramps: - One pair of galvanized one-piece steel ramps, approx. 3,000 x 800 mm, with approx. 48 mm thick hardwood covering - Ramp with hydraulic lifting mechanism, hydraulically adjustable - Maximum load per pair: 40,000 kg - In accordance with Regulation 1230/2012/EU, ramps with a length less than 300 mm do not count towards the vehicle length in the driving position Landing gears: - JOST landing gears (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: - BPW axles and suspension, 2 fixed axles, 1 trailing steering axle - Technical axle load: 12,000 kg each - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Axle tool kit Tyres: - Tyres 235/75 R 17.5 3PMSF – manufacturer of our choice - TPMS tyre pressure monitoring system in accordance with ECE R 141. The data transmission to the truck is via standardized EBS interface according to ISO 11992. For correct display, the truck must be able to transmit and display this data Braking system: - WABCO braking system in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Ledpfxew Tpqws Ac Aohf Steel construction: - Steel structure made of high-tensile fine-grain steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system according to EU regulations - Lighting 24 volts ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets as per ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: - Complete steel structure automatically shot-blasted with blasting wheel machine after welding - Second shot-blasting using corundum for optimal coating adhesion - HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure maximum corrosion protection - Final painting with 2 coats of two-component topcoat, single color in RAL 3002 Carmine Red, according to the RAL system 841GL - Rims in silver - Rear section metallized and in RAL 9010 (continuation see ori

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation Lhjdpsrgzv Nefx Ac Aef * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: new, maximum load weight: 40,790 kg, overall weight: 59,000 kg, axle configuration: 3 axles, total width: 2,750 mm, Equipment: ABS, You can find our complete vehicle inventory with immediately and soon-available vehicles on our website. Excerpt from the equipment list. Full specifications available on request. Gooseneck: - Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long - Gooseneck hydraulically liftable/lowerable and detachable - For tractor units: 6x4 or 8x4 Low bed: - Low bed with external beams, extendable design, SUPER LOW version, approx. 7,550 mm long - Low bed with fixed hardwood flooring, approx. 40 mm thick, and mechanical locking - Supply lines are protected within the extendable beams and automatically adjust to the current bed length - 7 pairs of lashing rings, foldable outward (approx. LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for mounting bolt-on RUD rings Rear running gear: - Rear running gear with closed outer frame, checker plate floor and continuous prism excavator trough, approx. 1,450/900 x 505 mm, open at the rear - 2 pairs of lashing rings, foldable outward (approx. LC 10,000 daN) - 1 pair of flat lashing rings in the trough (approx. LC 10,000 daN) - 2 pairs of flat lashing rings in the trough (approx. LC 16,000 daN) - 2 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame PENDLE-AXLE: - PENDLE-AXLE, all axles hydro-mechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic reset function - Hydraulic cylinders with shut-off valves and lock pins to secure in raised position - Final coating of axles with 2 coats of 2-component paint, single color in grey 34-0260 - Technical axle load: 12,000 kg each - Hydraulic axle compensation - Axle tools Tyres: - Tyres 245/70 R 17.5 3PMSF – brand of our choice. Load index (146/146F) Braking system: - Braking system according to EU regulations with EBS-E (2S2M) without interconnected lines to the tractor unit Electrical system: - Electrical system according to EU regulations - Lighting 24 Volt ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15 pin sockets. Connections according to ISO: 24N ISO-1185, 24S ISO-3731, 15 pin ISO-12098 Steel structure: Lsdpfx Aew Tprboc Ajhf - Steel structure made of high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Painting: - Entire steel structure automatically shot-blasted with a wheel blasting machine after welding - Second abrasive blasting with corundum for optimal adhesion of the coating system - Final coating with 2 layers of 2K topcoat, single color in RAL 3002 carmine red according to RAL system 841GL - Rear section metallized and painted in RAL 9010 (pure white) - Rims in silver-grey - No metallic paintwork possible - Paint structure tested in salt spray test according to ISO 9227-NSS - Sealing of cavities with special wax Accessories included: - Preparation for installation of bolt-on container positioning devices for 1x 20' or 1x 40' container on the outer beams - Without container locks - 3.5-inch king pin - One galvanized steel front wall, approx. 400 mm high - One spare wheel carrier in front of the front wall - At the galvanized front connection bar, yellow-red air couplings - Remote steering from front and rear via cable remote control with push buttons, with single-track monitoring of axles (without installation in the tractor unit) - Electro-hydraulic unit - On the gooseneck, plug-in aluminium side and rear walls, approx. 2,000 x 400 mm (L x H)

Condition: new, maximum load weight: 73,540 kg, overall weight: 102,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete inventory of vehicles, including units available immediately and at short notice, on our website. Overview of equipment. Full equipment list available on request. Neck (gooseneck): * Hydraulically liftable/lowerable and removable gooseneck, length approx. 3,650 mm * 2 pairs of fold-out lashing rings (LC 5,000 daN) * 2 pairs of lashing rings on the gooseneck (LC 10,600 daN) * 1 pair of lashing rings in the center section of the gooseneck (LC 10,600 daN) * For 6x4 or 8x4 2-axle tractor units Compact front bogie: * Hook pick-up front and rear, length: approx. 2,200 mm * Bogie width: approx. 2,850 mm Excavator deck: Telescopic excavator deck with drive-over deck hooks at the front and bolt-lug coupling at the rear * Basic width: approx. 2,850 mm * Length: approx. 6,650 mm * Beam height: approx. 400 mm * Beam width: approx. 1,350 mm * Loading height approx. 550 mm with ground clearance of approx. 150 mm 4-axle rear bogie: * Mechanical bolt-lug coupling at the front for mounting a lowbed * Rear crossmember bogie width: approx. 2,850 mm * Bogie length: approx. 5,480 mm Lodpfx Acjxbmplo Ashf Pendulum axles, all axles hydro-mechanically steered * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation Tyres: * Front bogie: * 8 x manufacturer’s choice (M+S) 285/70 R19.5 * Rear bogie tyres: * 16 x manufacturer’s choice (M+S) 285/70 R19.5 * Load index 150/148J Paintwork: * Complete steel construction is automatically blasted with a blasting wheel system after welding. Second blasting with corundum for optimal adhesion of the coating system * Full chassis HRM-metallized with ZINACOR 850 (85% zinc/15% aluminum) for maximum corrosion protection * Final painting with two coats of 2K topcoat, single-color in RAL 3002 carmine red, according to RAL system 841GL Including the following accessories: * Steel front wall, approx. 400 mm high * Plug-in ALU sidewalls and rear wall, approx. 400 mm high, anodized version, fitted on the gooseneck * 3.5 inch kingpin * Truck hydraulic connection with flow control (20 l/min) * Support gallows for supply lines, tractor unit tank must be at least 80 l * with MAX Trailer couplings, otherwise customer to supply coupling parts ex works * BEKA-MAX central lubrication for one gooseneck with standard grease NLGI-2 * Tool kit Art No. 612452 * Multi-coupling hydraulic connections on the gooseneck * Front bogie with separate air connection for air screwdriver * BEKA-MAX central lubrication for one 2-axle bogie with standard grease NLGI-2 * One 7-pin socket left and right rear on the front bogie for warning signs * Screw-in facility (ø approx. 40 mm) every approx. 500 mm on the outside of the upper flange of the outer tube of the excavator deck for bolt-on rings (LC 16,000 daN) * Foldable width extensions with steel covers, adjustable in width from approx. 2,850 mm to approx. 3,250 mm * BEKA-MAX central lubrication for one 4-axle bogie with standard grease NLGI-2 * At the rear bogie, a socket for the cable remote control of the steering * Rear bogie with trough * Two INOX toolboxes, approx. 855 x 340 x 390 mm, mounted left and right on the gooseneck * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery * Radio remote control: * Operation of the powerpack, start/stop of the diesel engine * Control of the steering, in addition to the cable remote control * One LED work light each left and right at the end plate of the gooseneck with...

Condition: new, maximum load weight: 25,300 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Excerpt from the equipment details. Full specifications available upon request. Neck (Gooseneck) * Gooseneck in SNT design to optimize loading platform length * Approx. 3,750 mm long, hydraulically liftable/lowerable and detachable * Technical fifth wheel load: 25,000 kg For tractors: 4x2 and 6x2 Kessel Bridge (Tiefbett section) * Low bed designed as extendable Kessel bridge in SUPER LOW design * Approx. 6,850 mm length * With mechanical locking * Service lines routed protected inside the extendable beams, automatically adjusting to match the low bed’s length Rear Chassis * Short version with closed outer frame and checker plate cover * Chassis with excavator trough, closed at the rear half to accommodate air tanks Lhedpfx Ajv Sw E Aec Aof Axles * BPW axles and suspension, all axles hydro-mechanically forced steered * Technical axle load: 12,000 kg per axle * Air suspension with lifting and lowering valve Tires * GOODYEAR KMAX T 3PMSF (M+S) 245/70 R 17.5 twin tires. Load index 143/141J (146/146F) Brake system * Brand: WABCO, EBS-E according to EU regulations, without connection cable to the tractor unit Paintwork * 6-Coat final treatment * All-steel construction shot-blasted after welding * 1 layer of zinc-based primer * 1 layer of adhesion primer. Final coating with 2 coats of 2-component acrylic paint in a single color, followed by cavity sealing with special wax Trailer color * RAL 3002 Carmine Red * Rim color: Silver grey * Drop side color: Natural aluminum Accessories included * Removable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic unit for hydraulic operations (except for hydraulic winches). Without supply connection installed on tractor unit * Spare wheel carrier in front of the gooseneck front wall * Side beams of the gooseneck with fixing holes for bolted lashing rings; first hole approx. 200 mm from the front, then at approx. every 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 lashing ring each left and right on the rear taper of the gooseneck (LC 6,000 daN) * 2" king pin * Hydraulic cross member for supporting the gooseneck on the tractor unit or a dolly * Air connection with air gun at the gooseneck * 1 pair of steel ramps with climbing strips and securing pins to bridge the mountings of the low bed * 1 lashing ring each left and right on the front cross member (LC 10,000 daN) * Outer side beams of the loading area prepared for removable loading floor * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the inside carrier’s exterior of the loading area * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the outer carrier’s exterior of the loading area (LC 10,000 daN) * Cut-outs above the lashing rings in the outer carrier’s upper flange * Mechanical pin-tab coupling from low bed to rear chassis, for swapping the loading floor or installing extension beams, with electro-pneumatic-hydraulic couplings * The outer carriers of the low bed coated with anti-slip sand finish for slip resistance * 2nd ride height for high ride position, max. ± 50 mm from normal ride position, without installation of controls from the tractor unit * 1 pair lashing rings with retaining spring at the transition from the low bed to the excavator trough (LC 10,000 daN) * Front and rear tapers

Condition: new, maximum load weight: 91,640 kg, overall weight: 126,000 kg, axle configuration: > 3 axles, total width: 2,850 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment features. Full specification available upon request. Gooseneck * Hydraulically liftable/lowerable and detachable gooseneck. Length approx. 3,650 mm. Suitable for tractor units: 6 x 4 or 8 x 4 3-Axle Compact Front Bogie * Hook couplings front and rear, length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Excavator Deck * Telescopic excavator deck BB-A with drive-over deck hooks at the front and a bolt coupling at the rear * Base width: approx. 2,850 mm, Length: approx. 7,150 mm, Main beam height: approx. 430 mm, Main beam width: approx. 1,350 mm * Loading height approx. 580 mm with ground clearance approx. 150 mm 5-Axle Rear Bogie Lhjdpfx Acjuvbdte Aof * Mechanical bolt coupling for front connection of a low-bed, rear end traverse * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * 3-axle pendulum axle Front Bogie * PENDULUM AXLE, all axles hydro-mechanically forced-steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off valves and stopper pins for securing in raised position * Axles finished with 2 layers of MB7350 Novagrau single-colour 2-component paint * Technical axle load: 14,640 kg per axle (62 km/h) * Hydraulic axle compensation * Front bogie tyres: 12 x Manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J, pendulum axle 5-Axle Rear Bogie * PENDULUM AXLE, all axles hydro-mechanically forced-steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off valves and stopper pins for securing in raised position * Axles finished with 2 layers of MB7350 Novagrau single-colour 2-component paint * Technical axle load: 14,640 kg per axle (62 km/h) * Hydraulic axle compensation * Rear bogie tyres: 20 x Manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J Paintwork * HRM metallization of the entire vehicle chassis using ZINACOR 850 (85% zinc/15% aluminium) to ensure the best possible corrosion protection * Final coat with two layers of 2K topcoat, single-colour in RAL 3002 Carmine Red, according to the RAL System 841GL. Rims in silver grey Incl. Accessories * Steel front wall, approx. 400 mm high * Detachable ALU side walls and rear wall approx. 400 mm high in anodized finish, mountable on the gooseneck * 3.5" kingpin * BEKA-MAX central lubrication system for one gooseneck * Multi-coupling hydraulic connections on the gooseneck * BEKA-MAX central lubrication system for one 3-axle bogie * One 7-pin socket left and right rear on the front bogie for warning signs * Screw-in option (ø approx. 40 mm) every approx. 500 mm on the outside of the upper flange of the external tube of the excavator deck for lashing rings (LC 16,000 daN) * Folding extensions with steel mattress, width adjustable from approx. 2,850 mm to approx. 3,250 mm * Steel mattresses can be positioned in 2 ways to achieve a lowered loading platform. Load capacity depends on extension, refer to the respective load chart * Steel mattresses with rubber flooring approx. 12 mm thick * One 7-pin socket left and right, front and rear of the rear bogie for warning signs * BEKA-MAX central lubrication system for one 5-axle bogie * Socket on the rear bogie for cable remote control of rear steering * Rear bogie with trough * Two INOX toolboxes, approx. 855 x 340 x 390 mm, mounted on the goos

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment specifications available on request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector strip with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized finish * 1 removable aluminum tailgate, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood floor above gooseneck, checker plate floor above king pin * 2-inch king pin * Rear section of gooseneck prepared for aluminum drive-on ramps * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform and bevel for accommodating excavator dipper stick approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st axle steerable, all remaining axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lockout, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with raise and lower valve * Tires: 235/75 R 17.5, twin tires, 3PMSF * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Continuous 50 mm thick hardwood floor on the loading platform and interrupted between axles (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable (galvanized) side extensions, approx. 230 mm per side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm ahead of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for wheel recesses, usable as bridging elements for extension OR as widening planks * Aluminum elements lockable on telescopic tubes of the extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening planks * Aluminum elements lockable on the extension’s telescopic tubes Lsdpetx Nwnsfx Ac Aohf * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-section steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm in length and approx. 900 mm wide each * Hydraulically foldable ramp tips * Ramps can be shifted hydraulically approx. 235 mm outward and approx. 215 mm inward individually * Super Grip rubber surface approx. 25 mm and steel plate surface approx. 5 mm as additional

Condition: new, maximum load weight: 45,250 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete inventory of vehicles available for immediate and short-term delivery on our website. Excerpt from the equipment list. Full specifications available upon request. Chassis, stepped: * Special steel frame made from high-strength fine-grained steels, electrically welded at connection points * Generously dimensioned outer frame. 4-axle configuration * Wheel covers over the axles with spray suppression * All steel parts sandblasted * Side underrun protection made of anodized aluminum mounted * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special construction in the stepped area for the longest possible low-bed length in combination with AluLeg drop supports instead of telescopic support legs, maximum rear swing clearance of the tractor unit approx. 2,100 mm Special body with rear stake extension: * DINKEL – special body * Self-supporting aluminum roof beam / profile approx. 120 x 100 mm, sliding roof with plastic flaps * Rear stakes extendable for loading/unloading up to approx. 4,200 mm * Three sliding stakes per side with elastic relief * Additional intermediate stake lockings in roof beam and parked position, via pull cable and spring bolt * DINKEL – mechanical lift roof, height-adjustable * Lift roof height approx. 400 mm, operable from both sides or one side without opening the opposite side * Additional height adjustment of approx. 480 mm in approx. 40 mm increments by adjusting the stakes * Front cover at bulkhead for driving operation under the tarpaulin up to a total height of approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminum slats on the side, 450 pockets below, four rows of single pockets above. Only three rows of slats in the raised platform, spacings evenly distributed Floor: * Approx. 27 mm special waterproof bonded beech phenolic plywood, rough surface * Steel sheet in the wheel well area. Suitable for forklift traffic as per DIN standard * Outer frame flush with deck surface Brakes: * WABCO air brake system with EBS according to EC Directive 71/320, including PREV (Parking-Release Safety Valve) * Spring-loaded brake cylinders as parking brake * WABCO Smart Board with mileage counter and axle load display Lhedewx Dbiopfx Ac Aef * Including WABCO tire pressure monitoring system Axles: * 4 x 10,000 kg SAF with drum brakes in low-loader design * Air suspension with lift and lower device, total lift approx. 230 mm * Third and fourth axles as friction-steered trailing axles with electric and mechanical lock Twin tires: * 235/75 R 17.5, 16-ply. Make of our choice, including spare wheel holder * Without spare wheel Lighting: * According to EU regulations, including LED side marker lights * Position lamps in LED design * 2 additional reversing lights * 2 work lights on the inside front wall, upper section Paintwork: * Chassis and body in one color, RAL 3002 carmine red * Intermediate stakes, axles KTL-coated black * Corner stakes hot-dip galvanized * Plastic parts black * Galvanized parts unpainted * Rims in factory silver Special equipment included: * 15-pin electrical supply cable * Air suspension in ECAS design, operated on the trailer * Oversize signage front and rear in galvanized, infinitely telescopic design with installed marker lights, including sockets for rotating beacons (small signs) * Additional external release for sliding roof frame lock * 4 stake adapters for special outer frame profile, to lock intermediate stakes as needed * PVC sliding tarpaulin, color similar to RAL 9

Condition: new, maximum load weight: 25,645 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete stock of immediately and soon-to-be available vehicles on our website. Ljdpfx Acjxf Silj Aohf Excerpt from equipment specification. Complete specification available on request. Load area: - Low-bed design with central beam, extendable version, approx. 6,750 mm in length - 5 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the loading platform (LC 10,000 daN) Gooseneck: - Hydraulic lifting/lowering gooseneck, detachable Rear chassis: - Short rear chassis with closed outer frame and checker plate covering - Chassis with excavator trough, closed in the rear half for housing the air tanks - 2 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Air suspension with raise/lower control valve Tyres: - Tyres 245/70 R 17.5, 3PMSF - TPMS: Tyre Pressure Monitoring System according to ECE R 141 Brake system: - Wabco braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - High-quality single-tone 2-component (2K) top coat in RAL 3000 Flame Red Including the following additional equipment: - 2 kingpins - Galvanised steel front wall, approx. 400 mm high - Remote steering from front and rear, operated by cable remote control with push buttons, including single tracking control for the axles (no installation in the tractor unit) - Electro-hydraulic unit - Axle load gauge including load diagram - On the gooseneck, removable aluminium side walls and rear wall, approx. 2,440 x 400 mm (L x H). Rear galvanised stake pockets are removable. (Body length approx. 2,560 mm) - Separate air connection with air gun on the gooseneck - 2 work lights with switch on the trailer, mounted on the left and right of the gooseneck platform - 1 INOX toolbox, approx. 1,350 x 400 x 400 mm, on the gooseneck - 6 pairs of stake pockets for insertable posts approx. 100 x 50 mm in the outer frame of the load area, 2 pairs in the chassis outer frame - Galvanised, extendable width extensions approx. 230 mm per side - Hydraulic connections from gooseneck to low bed with multi-coupling (instead of screw couplings). No seal guarantee included. - Central lubrication system with 2 BEKAMAX (Pico) pumps, standard NLGI-2 grease, with removable protection around the pump - 2 pairs of WADER container locks on the loading area, for 1x20' container - 1 removable galvanised intermediate table with 1 pair of WADER container locks - 1 pair of steel ramps for bridging the low bed’s hook mountings - Anti-slip sand-coated layer painted on the load area - HRM Metallisation (High Resistance Metallisation)

Condition: new, maximum load weight: 38,140 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpt from equipment. Full equipment details available on request. Gooseneck: - Gooseneck with front corners chamfered approx. 45° and rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, approx. 30 mm thick Loading area: - Telescopic loading area with rear incline approx. 1,000 mm x 8° - Between 1st and 2nd axle: one pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) - Incl. 3-piece removable galvanized cover over wheel recesses (width approx. 670 mm – max. point load 5 t / pc.) - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 4 pairs of outward folding lashing rings (LC 5,000 daN) - 3 pairs of outward folding lashing rings (LC 10,000 daN) - Cutouts in the outer frame for attaching tie-down straps (LC 2,000 daN) Landing legs: - JOST landing legs (manual) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Tyres: - Tyres 235/75 R17.5 3PMSF, make at our discretion - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transfer to the towing vehicle via standardised EBS interface as per ISO 11992 - For correct display, the towing vehicle must be able to receive and display this data Axles: - BPW axles and suspension, 2 axles rigid, 3rd axle self-steering - Technical axle load: 12,000 kg - Electromagnetic reverse lockout activated automatically when reversing and manually - Air suspension with lifting and lowering valve. Axle tools Braking system: - WABCO braking system according to EU regulations with EBS-E (2S2M) without piping to the tractor unit Electrical system: - Electrical system per EU regulations - LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets, according to ISO; 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel construction: Lhjdpfxew Tpq De Ac Ajf - Steel structure made of high-strength fine-grained steels - Steel qualities: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure automatically shot-blasted after welding in a wheel-blasting system - Second shot-blasting with corundum for optimum coating adhesion - HRM metallization of entire chassis with ZINACOR 850 (85% zinc/15% aluminium) for maximum corrosion protection - Final painting with 2 layers of 2K topcoat, single-colour in RAL 3002 Carmine Red, rear section metallized and painted in RAL 9010 Pure White - Metallic finish not available - Paint structure tested in salt spray test according to ISO 9227-NSS - Internal cavities sealed with special wax Including the following accessories: - On the gooseneck and rear, left and right, one holder for warning signs each, including socket - Spare wheel holder in front of the front wall (without spare wheel) - 2-inch king pin - Galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings on the galvanized front connection bar - Galvanized folding supports under the inclination at the rear of the loading area - A hardwood crash protection strip at the rear wall from gooseneck to the loading area - 1 pair of recessed lashing rings along the central beam at the rear inclination (LC 10,000 daN) - Aluminium drop sides and tailgate on the gooseneck