Low loader semitrailer

FAYMONVILLE F-S43-1AAF Multimax Tieflader,Radmulden 45 t.

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment specifications available on request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector strip with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized finish * 1 removable aluminum tailgate, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood floor above gooseneck, checker plate floor above king pin * 2-inch king pin Hfjdpfstx Nwnjx Aadoc * Rear section of gooseneck prepared for aluminum drive-on ramps * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform and bevel for accommodating excavator dipper stick approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st axle steerable, all remaining axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lockout, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with raise and lower valve * Tires: 235/75 R 17.5, twin tires, 3PMSF * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Continuous 50 mm thick hardwood floor on the loading platform and interrupted between axles (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable (galvanized) side extensions, approx. 230 mm per side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm ahead of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for wheel recesses, usable as bridging elements for extension OR as widening planks * Aluminum elements lockable on telescopic tubes of the extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening planks * Aluminum elements lockable on the extension’s telescopic tubes * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-section steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm in length and approx. 900 mm wide each * Hydraulically foldable ramp tips * Ramps can be shifted hydraulically approx. 235 mm outward and approx. 215 mm inward individually * Super Grip rubber surface approx. 25 mm and steel plate surface approx. 5 mm as additional

Condition: used, functionality: fully functional, Year of construction: 2020, operating hours: 920 h, ✅ Operator training is included at your site. ✅ The first owner was extremely satisfied with the innocrush crushing plant, particularly with its performance and ease of operation. However, due to a realignment of his business model, he no longer requires a mobile crusher. ✅ innocrush ic35 impact crusher with innoscreen is2 screening plant with recirculation/conveyor belt * Year of manufacture: 2020 * Operating hours: 920 * Condition: Very well maintained, ready for immediate use * Inspection: On site, demonstration of the plant possible ✅ Technical Specifications Hfsdpfx Ajwdxhhsadjc * Throughput capacity: up to 400 t/h * Feed opening: 1,250 x 710 mm * Transport dimensions (L x W x H): without screening plant & recirculation belt: 11.95 x 2.5 x 3.2 m with screening plant / recirculation belt (RFB): 14.5 x 2.95 x 3.2 m * Crusher weight: 34 t * Total weight incl. screen & recirculation belt: 38 t * Transport: Plant can also be transported in separate units (e.g. crusher + screening plant/RFB) --- ✅ Special Features * Crawler-mounted → flexible deployment directly on site * Compact transport dimensions * Robust technology – ideal for construction debris, natural stone, and recycling applications * With screening plant and recirculation belt (integrated & included in weight) * Very good overall condition * Regularly serviced * Windsifter (retrofit possible) --- ✅ Location & Inspection The plant is located near Frankfurt and can be viewed in operation by appointment at any time. ✅ Price & Contact Price on request. If interested, please send us a message or call us directly.

Condition: new, Year of construction: 2026, We have all Europe documents! Hodoqx Nd Rspfx Aadsfc We can delivery the trailers with FOB-EXW-CPT-CFR-CIF If you have an interest please contact with us; For European Countries; For African Countries;

Condition: new, functionality: fully functional, color: other, Year of construction: 2025, CONSTMACH stationary stone crushing plants are designed with a focus on high efficiency and durability, offering long-lasting industrial solutions. Each plant is specifically configured based on the hardness and abrasiveness of the material to be crushed and the desired product size. With production capacities ranging from 50 t/h to 1,000 t/h, they perfectly adapt to projects of different scales. The crusher types used in the plants are selected according to material properties to achieve maximum performance. Our design team creates optimized 3D layout plans using feeder, crusher, screen, bunker, washer, and conveyor components. This ensures high capacity, low energy consumption, and minimal maintenance costs throughout the production process. Each plant is custom-designed to suit the investment budget and operating conditions. Our engineering team offers the most suitable projects and proposals to prevent unnecessary expenses. CONSTMACH stationary crushing and screening plants are equipped with high-quality electronic components from SIEMENS and SCHNEIDER, and minimize operator intervention thanks to a PLC-based fully automated system. This provides safe, fast, and stable production. Fixed Stone Crushing Plant Technical Specifications Production Capacity: 50 – 1,000 t/h Type of Material to be Crushed: Varies according to the desired product type Final Product Dimensions: Adjustable upon request Crusher Types: Jaw, impact, cone, or vertical shaft crusher options Why Choose a Fixed Stone Crushing Plant from CONSTMACH? CONSTMACH makes a difference with its engineering approach that offers customized solutions to each customer. Our plants operate continuously for many years thanks to high-quality components, energy-efficient designs, and reliable automation systems. With our after-sales support service that prioritizes customer satisfaction, we are by your side at every stage of your investment. CONSTMACH is the right choice for fixed rock crushing plants offering powerful performance, low operating costs, and maximum efficiency. What Do We Do at Constmach? Constmach is a leading machine manufacturer offering a wide range of products tailored to the needs of the construction and mining industries. Our product portfolio includes concrete block making machines, stationary and mobile concrete plants, stone crushing machines, stone crushing and screening plants, sand washing machines, sand making machines, asphalt plants, conveyor belt systems, jaw crushers, and mobile crushing plants. With its high quality standards, innovative production approach, and customer-focused solutions, Constmach stands out as a reliable brand in both national and international markets. Our products continue to be the preferred choice of industry professionals due to their durability, efficiency, and long-lasting performance. Hsdpfx Aoxqhy Rsadsfc

Condition: used, Year of construction: 2014, Please contact Theo Lelie for more information Hfedpfx Aasxtqkwedsc

Condition: new, maximum load weight: 36,461 kg, overall weight: 49,500 kg, axle configuration: 3 axles, total width: 2,480 mm, total height: 860 mm, Year of construction: 2025, Technical Description Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). 30 mm thick hardwood flooring. Loading Platform: Loading platform behind the gooseneck hydraulically liftable and lowerable, length approx. 2,800 mm, with rear bevel of approx. 1,000 mm x 8°. 6 pairs of outward-folding lashing rings (LC 5,000 daN). 2 pairs of outward-folding lashing rings (LC 10,000 daN). 1 pair of inward-folding lashing rings on the front central beam (LC 10,000 daN). Grating flooring C40/4 (point load 2.3 t on an area of 20 x 20 cm), over the axles with chequer plate covering. Two-Part Steel Ramps: One pair of galvanized, two-part steel ramps approx. 3,185 + 1,420 x 1,250 mm with grating flooring C40/5 (point load 8 t on an area of 20 x 20 cm). Ramp with hydraulically foldable ramp sections and hydraulic lifting system. Maximum load per pair: 40,000 kg In accordance with regulation 1230/2012/EU, ramps less than 300 mm in length do not count towards the vehicle length of 16,500 mm in driving position. Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: Tyres 235/75 R17.5 3PMSF as per manufacturer’s choice. TPMS: Hfedpfow Dl Hwex Aadec TPMS tyre pressure monitoring system as per ECE R 141. Data transmission to the tractor unit via the standardized EBS interface according to ISO 11992. For correct display, the tractor unit must be able to receive and display these data. Axles: BPW axles and suspension, 2 fixed axles, 1 self-steering trailing axle. Technical axle load: 12,000 kg Electromagnetic reverse lock, activated via reverse gear and manually. Air suspension with raise and lower valve. Axle tools included. Brake System: WABCO braking system compliant with EU regulations with EBS-E (2S2M), without connecting lines to the tractor unit. Electrical System: Electrical system compliant with EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3). All LED side marker lights flash with the indicator. ASPÖCK-UNIBOX on the front connector strip with 24N, 24S & 15-pin sockets. Connection according to ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Structure: Steel frame made of high-strength fine-grain steels. Steel grades: – S355J2+N/S355MC (yield strength 355 MPa) – S690QL/S700MC (yield strength 690 MPa) Tarp Structure: Tarp structure approx. 3,960 mm – Galvanized front wall with a tensioning mechanism for the sliding curtains. – “EDSCHA” roof, forward-sliding on aluminum roof rail profiles (bolted to front and rear walls). – 3 pairs of movable stanchions on the loading platform. – Body can be hydraulically widened at the rear by approx. 750 mm to the left and right. – Sliding roof with upward-swinging portal carrier. – Sliding tarp with 700 mm length reserve and tensioning straps at approx. 600 mm intervals. Height to top edge of structure approx. 3,960 mm (loaded). – Driving with open sliding roof is not permitted and will cause damage to the tarp. Painting: Entire steel structure is automatically shot-blasted after welding using a blasting wheel system. Second blasting treatment with corundum for optimal coating adhesion. Full metallizing of the entire chassis with ZINACOR 850 (85% zinc / 15% aluminum) for best corrosion protection. Top coat with 2 layers of 2K finish, single-color in a shade of your choice according to the RAL 841GL standard. Rear section metallized and coated in RAL 9010 (pure white). No metallic paint.

Condition: new, functionality: fully functional, color: other, Year of construction: 2025, Equipment: cabin, hydraulics, CONSTMACH JS-1 mobile jaw and impact crusher is a high-efficiency mobile crushing and screening plant designed for processing natural stones such as medium-hard limestone, dolomite, and river stone. The JS-1 is manufactured with advanced engineering expertise and offers maximum efficiency even in challenging site conditions thanks to its durable components, high-performance crushers, and compact design. The system's first chassis features a CJC-60 primary jaw crusher, a vibrating feed hopper, a bypass belt, and a wheeled mobile chassis with hydraulic legs. The second chassis houses a CSI 1210 secondary impact crusher, a three-deck vibrating screen, a return belt, foldable stockpile belts, and a dust suppression system. Thanks to the powerful impact crusher design of the JS-1, the final products have an excellent cubic shape, providing ideal aggregate quality, especially for concrete production. The plant's production capacity varies between 60 and 80 tons per hour, depending on the hardness of the rock. Thanks to its user-friendly automation system, SIEMENS – SCHNEIDER brand components, and PLC control, the plant can be fully automatically managed via a tablet. Installation is completed in a short time, and the need for external equipment is minimized thanks to hydraulic opening mechanisms. The JS-1 can be easily transported with a single tractor due to its dimensions suitable for international road transport. JS-1 - Mobile Jaw and Impact Crusher Technical Specifications Production Capacity: 60-80 tph Maximum Feed Size: 600 x 380 mm Feed Height: 4.5 meters Main Configuration: Jaw Crusher + Secondary Impact Crusher + Vibrating Screen Total Motor Power: 275 kW Electric Generator Requirement: 550 kVA Plant Weight: 60 tons (total of two chassis) Plant Dimensions: 1st chassis 11x3x4.4 m / 2nd chassis 3.35x4.3x17.8 m Chassis Type: Double Chassis Hfsdpfx Aoxp Sc Teadjc Why Choose the JS-1 Mobile Crushing and Screening Plant? CONSTMACH JS-1 is an excellent choice for professionals seeking maximum efficiency, minimum operating costs, and superior product quality in the rock crushing process. Its fully automatic control system, high mobility capability, and durable construction offer uninterrupted production for many years. Furthermore, CONSTMACH's engineering expertise, after-sales technical support, and spare parts supply guarantee ensure the continuity of your business. If you are looking for quality, performance, and reliability in stone crushing solutions, experience the difference with the JS-1 Mobile Jaw and Impact Crusher, backed by CONSTMACH quality. What Do We Do at Constmach? Constmach is a leading machine manufacturer serving the construction and mining industries with a wide range of products tailored to their needs. Our product portfolio includes concrete block making machines, stationary and mobile concrete plants, stone crushing machines, stone crushing and screening plants, sand washing machines, sand making machines, asphalt plants, conveyor belt systems, jaw crushers, and mobile crushing plants. With its high quality standards, innovative production approach, and customer-focused solutions, Constmach stands out as a reliable brand in both national and international markets. Our products continue to be the preferred choice of industry professionals due to their durability, efficiency, and long-lasting performance.

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle fleet, including vehicles available immediately and at short notice, on our website. Excerpt from the equipment. Full equipment details available upon request. GOOSENECK: * Gooseneck in SNT design for optimization of loading platform length, approx. 3,700 mm long, with rear chamfer approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Plug-in steel front wall, approx. 400 mm high * ASPÖCK UNIBOX at the front connection rail with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, except hydraulic winches * On the gooseneck: 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized finish * On the gooseneck: 1 plug-in aluminum rear wall, approx. 400 mm high, anodized finish * Gooseneck covered with approx. 40 mm thick hardwood, king pin area with checker plate * 2" king pin LOADING AREA: * Extendable loading platform, approx. 8,800 mm long, with rear chamfer approx. 500 mm x 10° * A depression in the platform and chamfer to take up excavator dipper sticks, approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system according to ECE R 141. Data transmission to the truck via standard EBS interface in line with ISO 11992. For correct display, the truck must be able to transmit and display this data. * TPMS tire pressure sensors mounted on all wheels * BPW axles and suspension, 1st axle steered, all other axles hydro-mechanically forced-steered * 1st axle with electromagnetic reverse lock, activated by reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve * Axle tools * Mechanical landing legs with 2-speed gearbox and crank, JOST Modul B, static test load = approx. 50,000 kg * 245/70 R 17.5 3PMSF twin tires. Brand at our discretion. Load index 143/141J (146/146F) Hfsdpfx Aoyhkrfoadsc * Loading area with continuous (between the axles interrupted) 50 mm thick hardwood floor (provides increased coefficient of friction) * Platform locked using welded-on conical locking profiles, every approx. 250 mm; includes pre-tensioning plate * 1 intermediate platform, approx. 300 mm wide, for large-diameter sliding tube * Intermediate platform with recessed loading area and extendable suspension bars for aluminum bridging elements * 1 pair of lashing rings on the front cross-member (LC 10,000 daN) * 8 pairs of recessed lashing rings in the outer frame of the loading area, fold-out to the outside (LC 10,000 daN) * Extendable (galvanized) platform wideners, approx. 230 mm each side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm in front of the axles, fully open to the gooseneck cross-member, approx. 700 x 410 mm (W x D) * ALU covers for the wheel recesses that can also be used as bridging elements for the extension OR as platform widening planks (if the vehicle is equipped with extendable wideners) * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * 1 pair of mechanical rear supports * Steering from front and rear via cable remote control, with single-track control of the axles HYDRAULIC LOADING RAMPS: * DR-15/60-900-4350-KG-HV-M: One pair of two-piece steel ramps, approx. 4,350 mm long and approx. 900 mm wide

Condition: excellent (used), functionality: fully functional, fuel type: diesel, overall weight: 23,450 kg, Year of construction: 2018, operating hours: 3,950 h, Terex Cobra 230 impact crusher on tracks same as Powerscreen XH250 2018 year 3950 genuine working hours on John Deere John Deere 6068 194 kW 23450 kg Inlet[mm]:up to 860x720 mm Max size of inlet materiał: 400 mm Hjdpfxox S Hr Re Aadofc CSS[mm]: 0-20 to 0-100 mm Capacity[t/h]: from 100 to 150 Feed hopper 2,68 m3 Fitted with overband magnet Side conveyor and prescreem, can be bought. Wear plates 90% New blow bars martensitic-ceramic with double layer of ceramic(blue, RecyX) Machine in great working condition, can go straigt to work

Condition: new, functionality: fully functional, fuel type: electric, color: yellow, Year of construction: 2026, Our stationary crushing and screening plant, with a capacity of 200-350 tons per hour, consists of a 30 m³ vibrating feeding bunker, mid-screen, CLK-110 jaw crusher, cone crusher, vertical shaft impact crusher, stock and return conveyors, control cabin, and automation system. Products transferred to the feeding bunker are separated from dirt and mud using the intermediate screen and are bypassed with a bypass conveyor. The material above the screen goes to the jaw crusher, while the products on the second level drop onto the jaw discharge conveyor, and the products on the lowest level are discarded as bypass. The jaw crusher has a maximum feeding capacity of 800 mm and crushes the products, which first go to the washing screen. Here, the finest products are sent to the stock area with a screw washer, and the other products are sent to the cone crusher. The products coming out of the cone crusher are directed to the other screen and the vertical shaft impact crusher, allowing the desired products to be obtained from the final screen at high quality. TBX-30 Vibrating Feeding Bunker Hedpfx Aasyhld Aodsfc CLK-110 Jaw Crusher TE-2060x3 2000x6000 3-Deck Vibrating Washing Screen HY-800 8000x8000 Screw Washer 20m3 Cone Crusher Feeding Bunker CC-300 Cone Crusher 20m3 Vertical Shaft Impact Crusher Feeding Bunker VSI-900 Vertical Shaft Impact Crusher TE-2060x4 2000x6000 4-Deck Vibrating Screen TE-2060x3 2000x6000 3-Deck Vibrating Screen Conveyor Belts, Control Cabin, Electrical Panel, and Automation System