Low loader semitrailer

FAYMONVILLE MAX Trailer MAX510 Tiefbett 2x10 t

Condition: used, maximum load weight: 30,660 kg, overall weight: 43,000 kg, axle configuration: 2 axles, first registration: 03/2024, next inspection (TÜV): 03/2025, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Excerpt from the equipment list. Complete equipment list available upon request. Loading platform * Low-loader with central beam in extendable design * Length approx. 6,750 mm * 5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 1 pair of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings lying at the rear in the loading platform (LC 10,000 daN) * The supply lines are protected in the central beam and adapt to the respective low-loader length. Gooseneck * Length approx. 3,900 mm * Gooseneck can be raised/lowered and extended hydraulically * Technical saddle load: 23,000 kg Rear chassis * Rear end in a short design with a closed outer frame and diamond plate cover * Chassis with excavator well, which is closed in the rear half for accommodating the air tanks * 2 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 1 pair of lashing rings that can be folded outwards (LC 10,000 daN) Axles * BPW axles, hydro-mechanically forced steering * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Axle tool Tires * 245/70 R 17.5 3PMSF - brand of our choice * Load index (146/146F) Braking system * According to EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Steel construction * Made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Painting * High-quality 2-component (2K) paint * Topcoat in a single color, RAL 3002 carmine red Incl. the following additional equipment: * 2-inch kingpin * One galvanized steel front bulkhead, approx. 400 mm high * A spare wheel holder in front of the front bulkhead * Yellow-red air couplings on the galvanized connection strip at the front * 4 wheel chocks with holder. (± 5 kg) * Rear steering from the front and rear by means of a cable remote control via push buttons, with single-axle steering control (without installation in the tractor unit) Podpfx Aozm D Ucom Topw * Electro-hydraulic unit (± 45 kg) * Yellow reflector strip according to EU regulations on the side, on the extension and at the rear of the trailer * 1 wooden block, approx. 500x250x200 mm * Attachment rail for aluminum side ramps at the rear of the vehicle * A holder for a rotating beacon at the rear of the trailer * A splash guard at the rear of the trailer * European reflector signs (red-yellow) at the rear of the trailer * On the gooseneck and at the rear plate, one holder each on the left and right for the warning signs including socket * Manual and description on a USB stick * Speed stickers 80 km/h at the rear and on both sides * Load pressure gauge for determining the axle loads including load diagram Incl. special accessories * Aluminum side and rear walls on the gooseneck, plug-in, approx. 2,440 x 400 mm (L x H) * The rear galvanized plug-in end walls are removable. (Length of the superstructure approx. 2,560 mm). (± 46 kg) * A separate air connection with an air gun on the gooseneck * 2 work lights with a switch on the trailer, mounted on the gooseneck platform on the left and right * 6 pairs of rung pockets for plug-in end walls, approx. 100 x 50 mm in the outer frame of the loading platform * 2 pairs in the outer frame of the chassis (± 29 kg) extensions, galvanized, extendable by approx. 230 mm per side (± 262 kg) * Hydraulic conn

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, BONFIGLIOLI SQUALO 950 WITH NEW ENGINE! Psdpfxeyg Hhtj Am Tspw

Condition: new, maximum load weight: 30,190 kg, overall weight: 43,000 kg, axle configuration: 2 axles, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Extract from the equipment list. Full equipment details available on request. Loading Platform: - Lowbed with external beams in extendable SUPER LOW design, length approx. 6,850 mm - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking mechanism - Supply lines protected inside the extendable side rails, automatically adjusting to the current bed length - 5 pairs of lashing rings, foldable outward (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for attaching RUD screw-on rings Gooseneck: - Gooseneck in SNT design for optimized platform length, length approx. 3,750 mm - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractors: 4x2, 6x2 Rear Chassis: - Rear chassis in short version with closed external frame and checker plate cover - Running gear with excavator recess, closed in the rear half to accommodate the air tanks - 2 pairs of lashing rings, foldable outward (LC 5,000 daN) - 1 pair of lashing rings, foldable outward (LC 10,000 daN) - 1 pair of lashing rings horizontal, front & rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Technical axle load per axle: 12,000 kg - Air suspension with lift and lower valve Tyres: - Tyres 245/70 R 17.5 3PMSF - Manufacturer of our choice - Load index (146/146F) - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transmission to the truck via the standardized EBS interface in accordance with ISO 11992 - The truck must be capable of processing and displaying this data for correct operation Braking System: - Braking system according to EU regulations with EBS-E (2S2M) Electrical System: - Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with indicators - ASPÖCK-UNIBOX at the front connection point with 24N, 24S, and 15-pin sockets as per standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Steel Construction: - Steel construction from high-strength fine-grained steels Pjdpoxarl Nsfx Am Tepw - Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure is automatically shot-blasted after welding using a blasting turbine system - Second blasting process with corundum for optimal adhesion of coating system - HRM metallization of complete chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure maximum corrosion protection - Final paint finish with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, as per RAL system 841GL - Rims in silver - Rear section metallized and painted RAL 9010 (Pure White) - Metallic paint not possible - Paint system tested in salt spray test as per ISO 9227-NSS - Cavities sealed with special wax Including the following additional equipment: - 2" King pin - One galvanized steel front wall, approx. 400 mm high - Remote steering of front and rear axles by cable remote control with pushbuttons, including single track axle monitoring (without installation in the tractor unit) - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Electro-hydraulic power pack - Preparation for mounting container locks for 1x 20' or 1x 40' container on the external beams - Without container locks

Condition: new, maximum load weight: 25,645 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete stock of immediately and soon-to-be available vehicles on our website. Excerpt from equipment specification. Complete specification available on request. Load area: Pjdpfx Aoxf Silem Tepw - Low-bed design with central beam, extendable version, approx. 6,750 mm in length - 5 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the loading platform (LC 10,000 daN) Gooseneck: - Hydraulic lifting/lowering gooseneck, detachable Rear chassis: - Short rear chassis with closed outer frame and checker plate covering - Chassis with excavator trough, closed in the rear half for housing the air tanks - 2 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Air suspension with raise/lower control valve Tyres: - Tyres 245/70 R 17.5, 3PMSF - TPMS: Tyre Pressure Monitoring System according to ECE R 141 Brake system: - Wabco braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - High-quality single-tone 2-component (2K) top coat in RAL 3000 Flame Red Including the following additional equipment: - 2 kingpins - Galvanised steel front wall, approx. 400 mm high - Remote steering from front and rear, operated by cable remote control with push buttons, including single tracking control for the axles (no installation in the tractor unit) - Electro-hydraulic unit - Axle load gauge including load diagram - On the gooseneck, removable aluminium side walls and rear wall, approx. 2,440 x 400 mm (L x H). Rear galvanised stake pockets are removable. (Body length approx. 2,560 mm) - Separate air connection with air gun on the gooseneck - 2 work lights with switch on the trailer, mounted on the left and right of the gooseneck platform - 1 INOX toolbox, approx. 1,350 x 400 x 400 mm, on the gooseneck - 6 pairs of stake pockets for insertable posts approx. 100 x 50 mm in the outer frame of the load area, 2 pairs in the chassis outer frame - Galvanised, extendable width extensions approx. 230 mm per side - Hydraulic connections from gooseneck to low bed with multi-coupling (instead of screw couplings). No seal guarantee included. - Central lubrication system with 2 BEKAMAX (Pico) pumps, standard NLGI-2 grease, with removable protection around the pump - 2 pairs of WADER container locks on the loading area, for 1x20' container - 1 removable galvanised intermediate table with 1 pair of WADER container locks - 1 pair of steel ramps for bridging the low bed’s hook mountings - Anti-slip sand-coated layer painted on the load area - HRM Metallisation (High Resistance Metallisation)

Condition: new, Year of construction: 2024, functionality: fully functional, cutting force: 630 t, power: 110 kW (149.56 HP), total width: 2,400 mm, total length: 9,400 mm, total height: 3,800 mm, overall weight: 50,000 kg, cutting length (max.): 1,600 mm, type of input current: three-phase, Scrap Shear MS-6300mex (mobile version, with electrical motor) Diesel Generator 250KW is optional Modell: MS-63000e Cutting Power: 630t Blade length: 1600mm Output size: 500mm Power: 110 KW Capacity: 8-15 t/h Machine Weight: 39 t (+ Dieselgenerator 4t) Hooper size: 3900mm x 2400mm Information: Container Shear is used for economical scrap processing/ easy automatic operation/ energy saving/ cost saving/ no foundation needed. It can cut any kinds of scrap material. Different models for your choice. Machine is not suggested to cut high-carbon steel; axles; wire rope; pig iron; spring steel plate; rail; alloy steel; hub and so on... (these are not good for blades) Function: Scrap is filled into the hopper by means of a grab loader. Due to the horizontal movement of the holder and the scrap’s dead weight, it falls to the bottom of the loading chamber and into the cutting space. After having been compressed on the front wall, the scrap is cut by the horizontally-moving tool-holding side via the blades on the front wall. While the tool-holding slide is moving horizontally, the processed material is pushed out via the blades on the container’s front wall. While returning to the rear position, the loaded scrap moves under its own weight into the shears’ interior. The scrap shear machines are available with different design, depending on the customer requirements. The output size can be choose (only for new order). Podjr Ihzijpfx Am Tepw

Condition: used, maximum load weight: 25,600 kg, overall weight: 38,000 kg, axle configuration: 2 axles, first registration: 07/2025, next inspection (TÜV): 07/2027, Equipment: ABS, Excerpt from the equipment list. Complete equipment available upon request. Gooseneck Gooseneck Light, length approx. 4,080 mm Hydraulically extendable and retractable gooseneck For semi-trailer combinations: 4 x 2 and 6 x 2 Drop Deck Drop deck designed as a telescoping excavator bridge with a front extension and a mechanical locking mechanism. Length x width approx. 6,350 mm x 1,300 mm Rear Axle Assembly Rear axle assembly in a short design with a closed outer frame and diamond plate covering with an excavator well, which is closed in the rear half to accommodate the air tanks. Axles and Suspension BPW axles and suspension, all axles hydro-mechanically steered Technical axle load: 12,000 kg Pedpfx Amszlmkws Tepw Air suspension with lifting and lowering valve Axle tool Tires 235/75 R 17.5 3PMSF dual tires Load index 143/141J (144/144F) Braking System WABCO EBS-E braking system in accordance with EU regulations Without connection cable to the tractor unit Painting 6-layer end treatment Complete steel construction blasted after welding 1 coat of zinc-based primer, 1 coat of adhesion primer Final coating with 2 coats of 2-component paint (acrylic), single color in RAL 3002 carmine red, followed by sealing of cavities with special wax. Rims in silver. Included Accessories Steel headboard, plug-in type, approx. 400 mm high Connection strip for supply lines to the semi-trailer combination, mounted at the height of the outer frame profile Round NATO socket on the connection strip at the front (Maeler & Kaege VG 96 917) 3 kW electro-hydraulic unit for controlling hydraulic operations, with the exception of hydraulic winches 3 pairs of recessed lashing rings on the gooseneck (LC 5,000 daN) 2 pairs of welded lashing rings LBS 3 (LC 6,000 daN), at the front approx. 600 mm behind the headboard and at the rear on the gooseneck 2 pairs of welded lashing rings LBS 3 (LC 6,000 daN), on the outer frame of the gooseneck On the gooseneck, 2 pairs of plug-in aluminum side boards, approx. 400 mm high, in anodized design On the gooseneck, a plug-in aluminum rear panel, approx. 400 mm high, in anodized design Above the gooseneck, approx. 12 mm thick Delignit flooring 2-inch kingpin Hydraulic cross member for supporting the gooseneck on the semi-trailer combination or a dolly Air connection with air gun on the gooseneck Access to the gooseneck 2 pairs of rung pockets recessed on the gooseneck, for plug-in rungs approx. 100 x 100 mm On the outer tube, threaded holes for mounting screw-on lashing rings M24 (LC 8,000 daN) 2 pairs of screw-on lashing rings M24 (LC 8,000 daN) included On the top flange, approx. every 1,200 mm, attachment point ø26 mm for screw-on rings (LC 8,000 daN) 10 pairs of lashing rings on the outer girder RBS-5 (LC 10,000 daN), under and between the widening sections Folding, extendable widening sections, lockable to approx. 2,550/2,750/3,000 mm, incl. steel mattresses in a split design, with wooden flooring Bevel at the front of the axle assembly, approx. 350 mm x 12°, including integrated attachment rails at the front and rear for loose loading ramps 2 pairs of lashing rings with retaining spring at the transition from the drop deck to the excavator well (LC 10,000 daN) 3 pairs of recessed lashing rings in the outer frame of the axle assembly, foldable outwards: 1 pair at the front and 1 pair at the rear (LC 5,000 daN), 1 pair in the middle (LC 10,000 daN) 2 pairs of lashing rings LBS-3 (LC 6,000 daN) welded above the wheel arch on the rear axle