Used Fliegl Dts 300 P for sale (49,489)

Condition: new, machine/vehicle number: 2dff0c136c85096f36822a0bb, empty load weight: 7,150 kg, maximum load weight: 16,850 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support Dcjdpfx Alei Riy Eezsh 2 wheel chocks with holder Aluminum side collision protection Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points each 10 to integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation axle load compensation (rocker compensation) Brake system 2-line compressed air brake system Colored line routing for easy servicing. Spring-loaded parking brake Incl. 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 8,200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Incl. with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: ede0610378cbe39cc4883251d, empty load weight: 24,000 kg, maximum load weight: 7,550 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction 1st pair of wheel recesses after steel platform recessed in the tramline area, inclined towards the entrance, length at the bottom approx. 1400 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. If machines are to be driven where the overall height is to be checked, we request a technical data sheet for the machine types with exact details (if overall height is exceeded -> customer risk, approval required), (depending on the ground clearance under the machines, inserts in the wheel recesses may be required by the customer). Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side bumper Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 110 3 pairs of lashing points, 10 tons each, integrated in the floor at the front Incl. 6 pairs of lashing mushrooms at the top and sides, each 10 tons, embedded in the outer frame 1 x to neck area remaining distributed in between Distance not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles which guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Twin steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, incl. Dcodpfei Ri Rysx Alzsh Afterwards with 70 mm softwood floor, steel/checker plate covering in the wheel housing area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. cannot be achieved. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany Incl. with

Condition: used, axle configuration: 3 axles, total width: 25,500 mm, total height: 35,000 mm, Year of construction: 2018, Equipment: ABS, = Further options and accessories = - Air suspension rear - Air suspension front = Remarks = For inquiries about the vehicle, Mr. Seidel will be happy to assist you (by phone). Fliegl DTS 300 low loader trailer BPW axles, drum brakes, spring loaded brakes, mechanical ramps, permissible total weight: 24,000 kg, unladen weight: 6,350 kg, payload: 17,650 kg, loading area dimensions: L 8,490 mm x W 2,510 mm, tire profile: 1st axle 7-12 mm, 2nd axle 7-8 mm, 3rd axle 4-7 mm If required, we can provide you with a leasing or financing offer. Mr. Seidel (phone) will be happy to assist you. Dcodpjy Svrgofx Alzeh Further information is available on our website. ... Errors, changes, and prior sale excepted!!! = Further information = Unladen weight: 6,350 kg Payload: 17,650 kg Gross vehicle weight: 24,000 kg Please contact Tobias Ebert for further information.

Condition: new, machine/vehicle number: d461243f559015adca5bb372c, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing mushrooms at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Dcsdji Ri Dlepfx Alzsh Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco, Knorr or Haldex Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: 628cde0fe99cc2d3c8eaa8dd8, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm Dcjdsi Ri Ddepfx Alzjh 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles, at the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: used, empty load weight: 6,520 kg, maximum load weight: 23,480 kg, overall weight: 30,000 kg, axle configuration: 3 axles, first registration: 05/2019, loading space length: 8,610 mm, suspension: air, tire size: 235/75R17,5 ---/140J, color: other, gearing type: other, front tire size: 235/75R17,5 ---/140J, rear tire size: 235/75R17,5 ---/140J, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Loading area length drop deck approx. 6.50 m, loading area length total approx. 8.60 m, loading height approx. 900 mm, , Vehicle is offered on behalf of a bank, , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Dsdpezb Dk Iefx Alzech

Condition: new, empty load weight: 5,740 kg, maximum load weight: 24,260 kg, overall weight: 30,000 kg, axle configuration: 3 axles, color: silver, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, rotating beacon, 3 axles, SAF axles, turntable, leaf spring suspension, ABS (anti-lock braking system), can be widened to 3m, lashing points, two-part loading ramps, mechanical ramps, extendable drawbar, side aluminum fender, twin tires, EBS. Superstructure: Loading length approx. 8.5m, can be widened to 3.05m. Demo vehicle! Parabolic suspension with axle equalization at the rear, 3x 10t SAF axles, permissible gross vehicle weight 30t possible, drawbar adjustable in length. Djdpjxbttqofx Alzjch New vehicle from stock, registered on July 21, 2020. ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale and errors!

Condition: new, functionality: fully functional, machine/vehicle number: WFDFLT33001012559, empty load weight: 6,250 kg, maximum load weight: 17,750 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 9,620 mm, loading space width: 2,520 mm, total length: 10,890 mm, total width: 2,550 mm, total height: 860 mm, suspension: air, tire size: 235 / 75 R 17,5", tire condition: 100 %, color: black, Low-bed trailer chassis: Steel welded construction, turntable with robust ball bearing, foldable rear support, 2 chocks with holder, aluminum side impact protection, splash guards at the rear covering the entire width (not in conjunction with forklift mount), half-shell wheel arches, 1st axle with anti-spray splash guard, anti-spray splash guards behind the 2nd and 3rd axles, 1 plastic toolbox with insert, w=620/h=360/d=440 mm, lockable with a padlock, extendable widening sections to 3,000 mm, storage compartment for wooden planks in the center of the loading area, 70 mm wooden planks for widening to 3,000 mm, lashing points for low-bed trailers, 1 pair of lashing recesses in the front longitudinal beam, recessed in the flange, 10 tons each, 4 pairs of lashing holes in the outer frame, 5 tons each (for strap attachment), 7 pairs of lashing eyes recessed in the top and side of the outer frame, 10 tons each, 1 at the front in the flange, 6 in the low bed, the first lashing point 250 mm from the front and the last max. 250 mm from the rear, distance between lashing points not greater than 1100 mm, 5 pairs of ring lashing points recessed in the outer frame, 5 tons each (convertible to pocket lashing points), 2 pairs of folding lashing points additionally, 10 tons each, 1 on the flange (protruding), 1 behind the last axle recessed in the floor, 1 pair of screw lashing points, 6.7 tons each (JDT), with large flange plate including thread as counter-holder, at the front on the flange. Trailer turntable hitch: Drawbar with tested 40 mm drawbar eye, parking sockets for electrical/ABS and air connections on the drawbar. Axles + Suspension: SAF drum brake axles, "axle/chassis laser-measured" to reduce tire wear and fuel consumption, air suspension with lift and lower valve, operable separately at the front and rear. Dcedpfezaznzsx Alzjh Wheels and Tires: 235 / 75 R 17.5", Fulda, rims: 6 x steel rims in twin arrangement, mounted on the inside; 6 x aluminum rims, polished, mounted on the outside. Braking System: 2-line compressed air braking system, spring brake parking brake, Trailer Info Center for displaying vehicle data such as axle load (not an approved scale) and odometer, vehicle stability system, axle load detection via EBS-Canbus signal for display on the dashboard in the cab, truck must be appropriately pre-equipped, 2 non-interchangeable coupling heads at the front, with connection lines to the tractor unit, EBS, electronic braking system with EBS plug at the front, with connection cable. Electrical System: 24 Volt, multi-chamber lights in LED, yellow LED lighting on the sides, license plate lighting in LED, manufacturer Aspöck EcoLED 2 with dynamic turn signal, premium LED side marker lights, 2 white position lights at the front in LED, 2 white/red marker lights at the rear in LED, 2 x 7-pole non-interchangeable plugs at the front, with connection cable, additional LED work light at the rear, 1 LED rotating beacon with holder, switched via parking lights, 2 pairs of warning signs, LED-illuminated and extendable to 3,000 mm. Floor: Front flange with steel/diamond plate covering, storage box recessed in the ramp to the flange, followed by a 70 mm larch wood floor, steel/diamond plate covering in the wheel arch area, rear slope with 70 mm larch wood floor, low-bed area including rear slope 6,500 mm, loading ramps, steel ramps 2,800 mm long, 750 mm wide, laterally displaceable, additional ramp locking device, foldable at the bottom (to prevent lateral slippage o

Condition: new, machine/vehicle number: 195f80ad09517628522e33a91, empty load weight: 7,300 kg, maximum load weight: 16,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Dcodpfx Aoi Ri Rvjlzsh Quarter-shell mudguards in front of 1st axle 1st pair of wheel recesses after cranking, recessed in the low bed in the tramline area, slanted towards the entrance, bottom length approx. 1600 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. 2nd pair of wheel recesses recessed between the axles in the low bed in the tramline area, sloping towards the entrance, bottom length approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Widenings extendable to 3,000 mm (not in rear bevel) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Widenings extendable to 3,000 mm, also in the wheel recesses below, foldable on the wheel recess extensions, (widening not in rear sloping) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing cut-outs in the front side member, recessed on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable. Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed in the drive-over slope to the offset then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6500 mm Drive-on ramps Steel ramps 2 800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to

Condition: new, machine/vehicle number: f8fb99947a1c19bc4d63549ff, empty load weight: 6 kg, maximum load weight: 17 kg, overall weight: 24 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of front lashing eyes recessed on offset, 5 tons each 7 pairs of lashing rings at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each Dedpsi Riwfsfx Alzsch 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion with M&S marking Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Additional ramp safety device hinged at the bottom (to prevent the ramps from slipping sideways, not in conjunction with hydraulic side ramp displacement) covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Coun

Condition: used, first registration: 09/2016, color: other, Year of construction: 2016, Equipment: ABS, = Additional options and accessories = Djdjy Avafspfx Alzjch - BPW-Assen - Drum brakes - Lift Axle = Remarks = Fliegl, 2016, BPW axles, Axle 1 Liftable, Drum brakes = Dealer information = Bank data: Rabobank Account: 39.33.10.655 IBAN: NL73RABO0393310655 Swift code: RABONL2U - Always check our bank details before transaction! - Reservation of vehicles is not possible without a deposit. - Writing and text errors are reserved for all vehicles offered.

Condition: new, machine/vehicle number: 535119ca408d3bd5a8e74be51, empty load weight: 6 kg, maximum load weight: 11 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support Wheel chocks with holder Aluminum side collision protection Half-shell mudguards on 1st axle, quarter-shell mudguards in front of and behind the 2nd axle with anti-spray flaps behind each axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Widenings extendable to 3,000 mm (not in rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm), storage compartment for wooden planks in the middle of the loading area, wooden planks 70 mm for widening to 3,000 mm, Low loader lashing eyes 3 pairs of lashing points each 10 tons integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x according to the rest of the neck area distributed between them, spacing not greater than 1200 mm, 1 x rear slope 5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (instead of stake pockets) Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white/red rear lane departure lights 2 white position lights at the front 1 rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Front area steel floor, then with 70 mm softwood floor, steel/ checker plate flooring in the wheel arch area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Additional ramp safety device hinged at the bottom (to prevent the ramps from slipping sideways, not in conjunction with hydraulic side ramp displacement) covered with wood with spring lift support Operating instructions Dcedpfx Alei Ri N Hjzsh A special permit is required for axle loads of 10,000 kg. The permit must be applied for individually in each federal state; the legislator does not have to give a commitment for 20 tons GG. Customer risk. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. Approval / plates Country of approval: Germany Test approval according to EG 2007/46 24/7 service hotline Prepared for two-line license plate holder Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Warning sign according to ECE - 70 Paint finish Frame DB nova gray Drive-on ramps hot-dip galvanized Attentio

Condition: new, machine/vehicle number: b50cac2c60a813b0968994fa0, empty load weight: 5,700 kg, maximum load weight: 18,300 kg, overall weight: 24,000 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Rear spray flaps across the entire width Preparation for widening to 3,000 mm (holes in the outer frame and not in the rear slope) Low loader lashing eyes 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 5 x in the drop deck 1 x in the rear slope 12 pairs of lashing holes in the outer frame, each with 5 to. (lashing strap attachment) 5 x crank, 6 x low bed and 1 x in rear slope Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles, at the manufacturer's choice Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17.5 Fulda Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting lines to the motor vehicle, Connecting lines extended by approx. 60 cm without ABS, but with mechanical ALB, then max. 60 km/h approval Electrical system 12 volt, multi-chamber lights, without amber LED lighting at the sides, reflectors at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 1 x 7-pin 12 volt plug at the front, with connecting cable, extended by approx. 60 cm 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, illuminated and extendable to 3,000 mm, floor Front offset with steel/ checker plate covering Storage box recessed in drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 5900 mm Drive-on ramps Steel ramps 2 800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! Dodsi Ri Agjpfx Alzjch The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion, for max. 60 km/h registration, towing vehicle LoF, (max. 40 km/h possible in Switzerland) Prepared for two-line license plate holder without contour marking / reflective strips according to ECE R 048, Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: 55d3c5c03e032385649769b1b, empty load weight: 9,900 kg, maximum load weight: 14,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box recessed in Incl. Turntable front end Folding rear support 2 wheel chocks with holder Aluminum side bumper Rear spray flaps across the entire width Widenings extendable to 3,000 mm (not in rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points, 10 tons each, integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Drawbar with tested 40 mm towing eye Please note! With 40 mm drawbar eye, the maximum permissible total weight of the truck is 18000 kg, otherwise 50 mm drawbar eye required. Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring jack support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany 1 with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame Ral 3002 carmine red 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Dcodpfxei Ri I Ee Alzeh Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, Integrated pre-separator Integrated automatic extinguishing system Efficient and economical: large-volume compressed air tank with with fast-switching diaphragm valves for effective OPTI JET filter cleaning and minimum compressed air consumption. So simple and so effective: OPTI JET cleaning and bag filter with bag filter with snap ring lock. Extremely economical: Energy-efficient drives in accordance with IE3 Safe in the event of an emergency: Maintenance-friendly automatic extinguishing system. Peace and quiet: the soundproofed air recirculation system from AL-KO. All options are open: PLC control for manual and automatic automatic operation. Countless options from machine detection to slide control to frequency-controlled operation operation, to name just three examples. Nothing goes wrong: Collecting container with inspection window. Practical down to the last detail: container lock with ergonomically ergonomically shaped clamping lever. Can be retrofitted: conversion to discharge via briquetting press briquetting press or rotary feeder possible. - High suction capacity - little space requirement - 100 % air recirculation without temperature loss Dedpfx Aeu R S A Rslzech - (residual dust < 0.1 mg/m³) - Integrated pre-separator and expandable control unit - Optimum filter cleaning - Minimal noise level - Optional: patented fill level monitoring - Maintenance-friendly, certified automatic fire extinguishing system - Dust bulkhead for dust-free container change - (optional: safety interlocking of the containers) - Freely configurable module replacement and expansion options ----- Technical data ----- Extraction nozzle Ø: 300 mm, Nominal volume flow: 5,089 m³/h, max. volume flow: 6,000 m³/h, max. negative pressure: 2,587 Pa, Filter area: 30 m², Chip collection volume: 3 x 250 liters, Number of bags: 3 pieces, Motor 400 V: 7.5 kW, Dimensions (LxWxH): 3,000 x 1,058 x 2,361 mm, Sound pressure level: 71 dB(A), Weight: 838 kg, according to: GS - HO - 07 - new exhibition machine -

Condition: excellent (used), functionality: fully functional, usable tank capacity: 300 l, input voltage: 400 V, tank capacity: 300 l, total width: 850 mm, total length: 1,020 mm, total height: 1,300 mm, input frequency: 50 Hz, DGUV certified until: 06/2027, Sourdough machine Hema BRSSF 300 P Dodpfx Aljx Httwezjch Sourdough – Rapid – Fermenter with external LED control Stainless steel design DGUV V3 certified – only available from us Connection: 400V, 16A CEE plug Dimensions: 850 x 1020 x 1300/2040 mm (W x D x H) Used machine, cleaned with warranty & spare parts service Optional: Maintenance contract Service package Delivery service Instruction & commissioning Visit our wide selection!

Condition: used, Year of construction: 2013, functionality: fully functional, power: 7.5 kW (10.20 HP), input voltage: 400 V, input current: 13 A, input frequency: 50 Hz, type of input current: three-phase, volume flow: 5,089 m³/h, suction capacity: 5,089 m³/h, intake manifold diameter: 300 mm, actuation type: electric, overall weight: 972 kg, We are offering this used AL-KO POWER UNIT 300 P mobile extraction system, year of manufacture 2013. The extraction unit is in good condition and was kept in a heated room. The filters are clean and can be easily shaken off. Type: POWER UNIT 300 P Serial number: 2433358790 Year of manufacture: 2013 Suction nozzle: 300 mm Rated speed: 2,895 rpm Rated air flow: 5,089 m³/h Dcjdpsy Akfpofx Alzjh Rated current: 13.8 A Negative pressure at rated air flow: 2,050 Pa Protection class: IP 54 Motor power: 7.5 kW Weight: 972 kg Voltage/phase/frequency: 400/3~/50 Hz Max. compressed air connection: 8.5 bar Fuse: 25 A Filter number: 85101201 Filter category: Cat. M automatic gate/slide valve control If you have any questions or need further information, feel free to send us a message or call us.

Condition: good (used), functionality: fully functional, first registration: 07/2015, fuel type: diesel, overall weight: 7,500 kg, tire condition: 75 %, axle configuration: 4x2, fuel: diesel, color: white, gearing type: mechanical, emission class: euro5, number of seats: 3, total length: 8,650 mm, total width: 2,500 mm, total height: 3,500 mm, Year of construction: 2015, Equipment: ABS, central locking, crane, fog lights, onboard computer, === MAIN SPECIFICATIONS === Year: 2015 Hours: 5510 h Working height: 30 m Max. horizontal outreach: 19.5 m Platform capacity: 350 kg Truck type: MAN Number of axles: 2 Truck drive: 4x2 Transmission: Manual Cabin: Single Engine power: — Fuel type: Diesel Platform dimensions (L x W): 1.6 m working cage Platform rotation: Yes (80° + 80°) Boom type: Telescopic / articulated combination Stabilisers: Yes – hydraulic outriggers CE certification: Yes Total vehicle weight: 7,500 kg === HIGHLIGHTS === Carefully selected from reliable sources with verifiable history CE certification and full documentation included Ready for immediate transport and operation Extensive technical documentation available === CONDITION === Excellent working condition – fully inspected, serviced and tested by certified professionals. Inspection possible upon request. Dcodpfxjyr Nkzj Alzsh === LOCATION & PRICE === Located in Sittard, Netherlands Worldwide delivery available Price on request (EXW / excl. VAT) Reliable truck mounted access platform from the well-known manufacturer Palfinger. The Palfinger P300 KS offers a maximum working height of 30 meters and a horizontal outreach of up to 19.5 meters, making it ideal for maintenance, installation, construction and infrastructure work. The machine is equipped with hydraulic outriggers, automatic cage levelling and a rotating aluminium working platform, ensuring stable and safe operation in various working environments. All machines are fully inspected, CE-certified and ready for immediate use. === DELIVERY === Crane loading available upon request for smooth transportation. Flexible shipping options tailored to your destination and logistics preferences. All transports handled professionally by the logistics team of Collé Rental & Sales.

Condition: excellent (used), functionality: fully functional, first registration: 06/2015, fuel type: diesel, overall weight: 7,490 kg, tire size: 295/80 R22.5, axle configuration: 4x2, wheelbase: 3,050 mm, fuel: diesel, color: blue, Year of construction: 2015, operating hours: 5,448 h, Equipment: ABS, air conditioning, car registration, crane, hydraulics, === SPECIFICATIONS === • Year: 2015 • Operating hours: 5,448 h • Max platform capacity: 350 kg • Max working height: 30 m • Jib reach: 20+ m • Power supply: Diesel • Remote control: Yes • Jib function: Movable jib • Additional equipment: 230V socket in basket • Tyre type: Pneumatic • Weight: approx. 13,000 kg • CE certified: Yes === HIGHLIGHTS === Dedpfx Aloxw T D Ujzsch Carefully selected from trusted sources with verifiable history CE certification and complete documentation included Ready for immediate transport and operation Comprehensive technical documentation available === CONDITION === Excellent working condition — fully inspected, serviced, and tested by certified professionals. Inspection available upon request. === LOCATION & PRICE === Located in Sittard, Netherlands Worldwide delivery available Price: €119,500 EXW (excluding VAT) Reliable first-owner Palfinger P 300 KS with full service history and technical support. All machines are CE-certified and ready for immediate use. Spare parts and professional assistance available on request. === DELIVERY === • Crane loading available on request • Flexible dispatch options tailored to your destination • All transport handled professionally by the Colle Rental & Sales logistics team

Condition: good (used), functionality: fully functional, Year of construction: 2015, load capacity: 350 kg, mast type: telescopic, lifting height: 28,000 mm, lifting power: 350 kg/m, platform length: 1,800 mm, platform width: 1,000 mm, overall weight: 7,490 kg, transport length: 7,600 mm, transport width: 2,520 mm, transport height: 3,500 mm, fuel type: diesel, wheelbase: 3,050 mm, color: blue, Equipment: ABS, 🔧 Key Specifications: • Year: 2015 • Mileage: 59,640 km • Max. working height: 30.0 m • Max. horizontal outreach: 19.5 m • Platform capacity: 350 kg • Platform rotation: 2 × 80° • Boom rotation: 540° • Drive: Diesel • Machine weight: 7,500 kg • CE certified: Yes ✨ Highlights: Djdpfjxdauyox Alzsch ✅ Condition: 4/5 ✅ CE certification and full documentation ✅ Fully flexible outrigger setup: full / one-sided / narrow ✅ Stable and powerful – suitable for various industries ⚙️ Condition: Fully functional and ready for immediate delivery. 🌍 Location & Delivery: 📍 Sittard, The Netherlands 🚚 Worldwide delivery possible 💰 Price: €119,500.- EXW, excl. VAT One of the most flexible and capable 7.5-tonne machines on the market, with counter-slew boom rotation, automatic jacking and cage leveling, and a fixed 1.6 m working cage. Built on a reliable MAN chassis. 🚚 Delivery: • Professional handling and crane loading available • Flexible shipping options tailored to your needs • Managed by the Collé Rental & Sales logistics team.

Condition: excellent (used), Year of construction: 2023, load capacity: 400 kg, mast type: telescopic, lifting height: 28,000 mm, lifting power: 400 kg/m, platform length: 1,800 mm, platform width: 1,000 mm, overall weight: 7,400 kg, transport length: 7,600 mm, transport width: 2,520 mm, transport height: 3,500 mm, fuel type: diesel, tire condition: 95 %, color: white, Equipment: ABS, 🔧 Key Specifications Year of manufacture: 2023 Dedpfx Aloxdawzjzoch Mileage (chassis): 858 km Working height: 30.0 m Maximum horizontal outreach: 20.5 m Platform capacity: 400 kg Platform rotation: ±85° Platform dimensions (L × W): 1.80 × 1.00 m Boom type: Telescopic with counter-slew rotation Truck chassis: MAN (7.5 t) Axles: 2 Drive: 4×2 Transmission: Automatic Fuel type: Diesel Total vehicle weight: 7,400 kg CE certified: Yes ⚙️ Condition As new / unused condition. Fully inspected and ready for immediate use. 📝 Description 30 m truck-mounted aerial work platform built on a MAN 7.5-ton chassis. The machine offers a working height of 30.0 m, a maximum outreach of 20.5 m and a platform capacity of 400 kg. Equipped with telescopic boom with counter-slew rotation, automatic jacking and automatic cage leveling. Fixed working cage. CE-certified and immediately available. 🌍 Location & Delivery Location: Sittard, The Netherlands Worldwide delivery available Price: €291,000 EXW (excl. 21% VAT) Professional handling and crane loading available. Transport can be arranged by Collé Rental & Sales.

Condition: excellent (used), Paoloni P 300 Panel Saw with Scorer | 3200mm Carriage, Italian, 790kg Dcsdpsy Tzqksfx Alzoh Description: For sale is a professional, classic panel saw from the renowned Italian manufacturer PAOLONI, model P 300. The machine features a very heavy, cast iron and steel construction (weighing a substantial 790 kg), which ensures excellent stability, geometric rigidity, and superior vibration damping during operation. This is a proven, mechanically reliable design without unnecessary, failure-prone electronics – ideal for use in artisanal carpentry workshops and for furniture production. ⚙️ TECHNICAL DATA FROM THE NAMEPLATE: Manufacturer: Paoloni (Fano - Italy) Model: P 300 Year of manufacture: 1997 Serial number: 0602 Supply voltage: 380 V (Three-phase) Frequency: 50 Hz Motor power (KW): 4.75 kW Current consumption: 11 A Machine weight: 790 kg 💎 MAIN FEATURES AND EQUIPMENT: Long Aluminum Panel Saw Carriage: Provides smooth, effortless feed and high cutting precision. The carriage length allows for easy cutting of full-size furniture panels (cutting length approx. 3200 mm). Scoring Unit: Essential for clean cutting of laminated, chipboard, and MDF panels – guarantees no chipping of the material on the underside. Precise Geometry Adjustment: Manual, reliable raising/lowering of the main saw blade and adjustment of the blade tilt angle (in the range of 0°–45°) using an ergonomic wheel with a dial indicator. Stable Side Table: Structure mounted on a solid, telescopic support arm, equipped with a long transverse ruler with two stops for series cuts. Parallel Guide: Solid mounting on a thick, steel rod, ensuring repeatable dimensions on the right side of the blade. 📐 OPERATING PARAMETERS (Standard for the P 300 series): Cutting length: approx. 3200 mm Cutting width with the right guide: approx. 1150 mm Maximum main blade diameter: 300 mm - 350 mm Cutting height: up to approx. 100 - 115 mm (depending on the installed blade) 🛠️ TECHNICAL CONDITION: The machine is complete, in good visual and technical condition. Ready for immediate use in the workshop.

Year of construction: 2024, condition: used, functionality: fully functional, PROFIL Floor Saw Typ COMPACTCUT 300 P Typ COMPACTCUT 300 P — Year of manufacture 2024 Used, from the professional rental fleet of Kurt König Baumaschinen GmbH, Einbeck, Germany. Floor saw particularly suitable for light road rehabilitation and landscaping. Robust Honda petrol engine. Technical data: Weight: 104 kg | Max. cutting depth: 175 mm | Drive: Honda Petrol Condition & Notes: - Condition: Used, ex-rental, regularly serviced Dcodpsy A E Tuofx Alzeh - Functionality: Fully operational - Product photos to follow — please contact us for current images - On-site inspection in 37574 Einbeck available by appointment Price EUR 2,200 plus VAT | EXW Einbeck | Delivery upon request

Condition: used, Screw vacuum pump - Unused Manufacturer: Alcatel / Adixen Type: A 300 P Dcodpfecw Idaox Alzeh Motor: 380-460V Status: Used; As good as new Warranty: 12 months Suction power: 320 m³/h connection: ISO-K 63 Ultimate pressure: approx. 1.2x10-2 mbar (abs.) Included: Operating instructions

Year of construction: 2013, condition: used, We are offering this used TE Connectivity Insertion Machine P 300 pin inserter, year of manufacture 2013. Operating condition: "System functionality is no longer fully ensured. Functional limitation: After switching on, automatic initialization/homing does not work." If you are interested, we are certainly open to negotiating a price. Dcjdpfx Aley R I Uwjzjh Machine type: Insertion Machine P 300 Serial number/part number: 1-1372900-4 Manufacture date: 01/2013 Supply voltage: 230 V Phases: 1P~ Frequency range: 50/60 Hz Rated current: 2.5 A Max. current: 10 A Short-circuit current: 50 kA Required air pressure: 6 bar Weight: 1600 kg If you have any questions or need further information, please feel free to send us a message or call us.