Used Mütek Mfp 30 for sale (23,752)

Condition: as good as new (ex-display), Year of construction: 2025, Machine for sale at a special price Another machine, available immediately (ex works Neckartailfingen) * Including 1 year warranty. Your advantages: + Very robust, simple technology + Top price-performance ratio + Suitable for continuous operation + Long-standing, well-functioning / established machine Including control cabinet with timer operation Press is switched on manually and then runs until the time set on the timer (e.g. 4 hours) has elapsed. Then the press switches off. Technical data: Briquette dimensions: approx. 30 x 30 mm (square), Nodpfxsd Nnwle Ahzelb Briquette length: 5-40 mm *depending on material Throughput capacity: up to a maximum of 20 kg/h. *depending on material Machine dimensions approx. 137 x 75 x 148 cm (length x width x height), Weight of the machine: approx. 250 kg, Capacity of the silo: approx. 250 liters, Motor: 2.2 kW, 400 V - 50 Hz, Noise emission: 62 dB, Raw material requirements: -Wood chips and dust smaller than 15 mm in length -Moisture content less than 18 % ATRO -Sand, stones, metals and minerals increase wear --- Options at extra charge: --Timer function + 490 € net Machine is started manually and switches off automatically after a set time X. -Level indicator for automatic operation + 1450 € net Press starts and then stops automatically * NEW !!! Also available in 230 Volt, Motor then 3 kW instead of 2.2 kW, Surcharge + 890 € net (delivery time then approx. 8 weeks) - Special pressing units + 2.950 € net ---

Condition: as good as new (ex-display), Year of construction: 2026, Machine available at special price Machine available immediately (ex works Neckartailfingen) Demonstration unit Your benefits: + Very robust, simple technology + Excellent price-performance ratio + Suitable for continuous operation + Long-established, reliable machine Including control cabinet with timer operation The press is switched on manually and will run until the set time on the timer (e.g. 4 hours) has elapsed. After that, the press switches off automatically. Technical data: Briquette dimensions: 30/35 mm (square), Briquette length: 5–35 mm (depending on material) Nsdofci D Aepfx Ahzslb Throughput capacity: up to max. 25 kg/h (depending on material) Machine dimensions (approx.): 137 x 75 x 148 cm (L x W x H), Machine weight: approx. 250 kg Silo capacity: approx. 250 liters Motor: 2.2 kW, 400 V, 50 Hz Noise emission: 62 dB Raw material requirements: - Wood shavings and dust less than 15 mm in length - Moisture content less than 15% ATRO - Sand, stones, metals, and minerals increase wear --- Optional upgrades (at extra cost): - Timer function + €490 net Machine is started manually and switches off automatically after preset time X. - Level sensor for automatic operation + €1,450 net Press starts and stops automatically * NEW! Now also available in 230 Volt version Motor then 3 kW instead of 2.2 kW Surcharge + €690 net (delivery time approx. 8 weeks) ---

Condition: as good as new (ex-display), Year of construction: 2024, Special price: €29,970 net A machine is currently available immediately. The ideal machine for shredding voluminous, light aluminum chips or turnings. Not suitable for more solid aluminum parts. Includes: + Optimized cutting geometry + Adapted slide control Nlodpfegmh H Tjx Ahzeb + Load-dependent controlled hydraulic slide (which presses the chips against the cutting mechanism) Motor: 18.5 kW; 400 V - 50 Hz - 3 ph, Blade: 40x40mm, multi-rotatable, Rotor diameter: 260 mm, Control: Omron PLC, Cutter opening 600 x 800 mm, Funnel volume approx. 0.6 qbm, Hydraulically operated slider Sieve perforation of your choice (15 - 40mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (lxwxh) approx. 1737 x 1167 x 1650 mm The following options are available for an additional charge: - Raise the shredder by 30 cm (preparation for conveyor belt) +2,990 € net - Angle conveyor belt (discharge height approx. 220 cm) +9,770 € net - Overband magnet + €6,980 net - Control of conveyor belt and overband magnet + €2,750 net (Start and stop synchronized with the chipper) We would be happy to carry out a free test with your material. We invite you to come to us in Neckartailfingen. It is also possible for you to send us your material by freight forwarder and we will document the test with pictures and videos.

Condition: new, Year of construction: 2026, Production time appr. 4 months Our best-selling briquetting press series + Tried and tested, simple technology for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several hundred machines in use with satisfied customers + Good price performance ratio Throughput approx. Up to 200 kg per hour * strongly dependent on the material. - in the last test with aluminum granules smaller than 5 mm - approx. 186 kg per hour + the pressed emulsion. - in the last test with aluminum chips smaller than 18 mm - approx. 120 kg per hour + the pressed emulsion. Technical specifications: Motor: 7.5 KW + 0,55 kW Cooler 400 volts / 50 Hz / 3-phase, Front bush: 125 mm, Briquette stroke max .: 100 mm, Briquette stroke opt .: 80 mm, Pump: 80 liters, Storage container approx. 0.5 qbm content (expandable), Diameter: 1200 mm, with agitator discharge, Hydraulic unit complete with oil tank 220 liters Nlsdpfxjchqxxj Ahzeb Dimensions approx. 2095 x 1600 x 1310 mm lxwxh, Weight 1370 kg, Automatic on-off switching via level indicator CE compliant. . Requirements for the raw material: - Chip length maximum 20 mm - Installation temperature: temperature-controlled room at at least + 5 ° C - The loading must be free of magnetic metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: as good as new (ex-display), Demonstrator with 7 operating hours Another machine available immediately (ex works in Neckartailfingen) MRZ 830 Shredder Custom tariff number: 84659600 Feed opening 800 x 1000 mm Motor: 18.5/22 kW; 400 V - 50 Hz - 3 ph Blades: multi-rotatable Nljdsv Sqrpepfx Ahzeb Hydraulically operated slide gate Screen perforation of your choice (10 - 40 mm) Weight approx. 1,600 kg Dimensions (L x W x H) approx. 2,290 x 1,420 x 1,750 mm Turbo clutch Included as standard: - Automatic star/delta start-up - Fast hydraulics - Auto. OFF when the rotor is idle - Speed 70-90 rpm for high throughput - Cycle control to avoid idle times - Performance-enhancing step control of the hydraulic slide - Pertinax guides for the hydraulic slide - Vibration-damping machine feet - CE compliant . The shredder is designed for shredding natural wood, particle board, and MDF, as well as other materials after testing and approval by the manufacturer. Included: - Raise the shredder by 30 cm (prepared for conveyor belt) Additional shredder options: - Articulated conveyor belt + €8,770 net Horizontal section: 1,200 mm Rising section: 2,500 mm Angle: adjustable from 0-60 degrees Discharge height: approx. 2,000 mm + - 100 mm - Overbelt magnet + €6,780 net - Conveyor belt and overbelt magnet control + €2,750 net (Start and stop synchronized with the shredder) Raw material requirements: - The moisture content (dry) must be below 30% - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear

Condition: as good as new (ex-display), Year of construction: 2024, Special-purpose machine for plastics shredding Base machine from €24,990 net Ideally suited for shredding: - Paper, cardboard, pipes, profiles, boxes, canisters, buckets, cans, wooden pallet offcuts, etc. - Medium-hard thermoplastics such as PVC, PP, PE, PS, PU, PET Nsdpfod H R Sxox Ahzolb Included: - Special rotor with embedded knives (reduced load uptake) - Minimal cutting gap between rotor and counter knives Motor: 18.5 kW; 400 V - 50 Hz - 3 ph Control: PLC Cutting chamber opening at the top: 600 x 800 mm Maximum recommended input material size: approx. 500 x 500 mm (*height less critical) Hydraulically actuated pusher Screen perforation options: 25 - 40 mm For plastics, coarser screens are recommended (30-40 mm) *For finer granulation, a two-stage shredding process with downstream granulator type MVZ (screens 5-15 mm) is recommended Exhaust port Ø 160 mm Weight: approx. 1,300 kg Dimensions (LxWxH): approx. 1737 x 1167 x 1650 mm Additional options available at extra charge: - Raise shredder by approx. 25 cm (preparation for conveyor discharge): + €1,980 net - Inclined conveyor belt (discharge height approx. 220 cm): + €8,770 net - Overbelt magnet: + €5,980 net - Conveyor and overbelt magnet control: + €2,750 net (synchronized start/stop with shredder) - Alternatively, manual start/stop function at conveyor: + €595 net Raw material requirements: - Moisture content (atro) must be below 25% - Metals and mineral contaminants such as sand, stones, etc. will result in increased wear We are happy to offer a free test using your material at our facility in Neckartailfingen. Alternatively, you may send your material to us via freight forwarder and we will document the test using photos and videos. --- * Only for brittle plastics of medium hardness. * Not suitable for elastic or extremely hard and heavy plastics – this will negatively impact the durability of the system. --- Optional: Larger machine sizes available Base machine: Shredder MGZ 830 K-S – 18.5 kW Cutting chamber opening at the top: 800 x 1,000 mm Maximum recommended input material size: approx. 720 x 700 mm (*height less critical) From €39,995 net (*options subject to additional cost) Base machine: Shredder MGZ 1030 K-S – 22 kW Cutting chamber opening at the top: 1,000 x 1,000 mm Maximum recommended input material size: approx. 900 x 700 mm (*height less critical) From €49,975 net (*options subject to additional cost) Base machine: Shredder MGZ 1330 K-S – 37 kW Cutting chamber opening at the top: 1,300 x 1,200 mm Maximum recommended input material size: approx. 1,200 x 700 mm (*height less critical) From €79,975 net (*options subject to additional cost)

Condition: new, Year of construction: 2026, Your advantages: + extremely large cutting unit opening with 1300x1200mm + special rotor suitable for hardwood and softwood + Energy-efficient and powerful with 37 kW at start-up Technical specifications: Colour: grey / blue Feed opening (mm): 1,300 x 1,200 Hopper capacity (cbm): 1.6 m³ Rotor diameter (mm): 368 Rotor speed (rpm): 65 - 125 Power requirement (kW): 37 Screen perforation (mm): 30 - 50 mm - selectable Tools: 37/70 knives Extraction nozzle Ø (mm): 200 mm Njdegbkkrspfx Ahzslb Dimensions: 2430x2410x1735 mm (lxwxh) Weight (approx. Kg): 3,920 Optional for a surcharge: * to shred veneer or paper (anything thinner than 3 mm) - we recommend a segment floor. The machine in preproduction has not yet installed this. Special option at an additional cost. - 2nd row of knives, for up to 30% more throughput - Fast hydraulics, for increased throughput - Preparation for conveyor belt removal - conveyor belt - HAWK-EYE overbelt magnet --- Optimal pallet size with the option slide extension = 1200x1400 (option slide extension, the cutting unit opening 1300x1700 surcharge + 12,975.00) * is associated with significantly longer production time. * larger machines on request --- Requirements for the raw material: - The moisture content (atro) must be below 30% - The loading must be free of metals and mineral impurities. This can result in damage to the tools and / or increased wear

Condition: as good as new (ex-display), Year of construction: 2025, Demonstration machine with approx. 9 operating hours Another unit available immediately (ex works Neckartailfingen) *Options at additional cost – see below Included: + Profile rotor for increased throughput performance Nodjb Ny Eyjpfx Ahzolb We are happy to arrange a free test with your material. You are welcome to visit us in Neckartailfingen for this purpose. Alternatively, you may send your material to us via freight forwarder and we will document the test with photos and videos. Motor: 18.5 kW; 400 V - 50 Hz - 3 ph Knives: 15 pieces, reversible multiple times Optional double knife row + €995 net Rotor diameter: 260 mm Control: Siemens S7-1200 PLC Cutting unit opening: 630 x 820 mm Hopper volume: approx. 0.6 m³ Hydraulically operated pusher Screen perforation as desired (10 - 40 mm) Extraction port Ø 160 mm Weight: approx. 1,300 kg Dimensions (LxWxH): approx. 1737 x 1167 x 1650 mm Moisture content: < 30% dry basis. Standard features included: - V-rotor for maximum throughput - Control cabinet with Siemens PLC - Automatic star/delta start - Rapid hydraulics - Automatic stop when rotor is idle - Speed 70-90 rpm for high throughput - Cyclic control to avoid idle times - Performance-boosting incremental control of the hydraulic pusher - Pertinax guides for the hydraulic pusher - Vibration-damping machine feet - CE compliant Optional extras for the shredder (at additional cost): - Raise shredder by 30 cm (preparation for conveyor belt) + €2,080 net - Eco-rings: + €1,980 net (recommended for over 20% hardwood) - Double knife row + €995 net - Special scraper + €990 net (recommended for shredding veneer, paper or thin materials < 3 mm) - Angled conveyor belt + €8,770 net (angle adjustable 0–60°, discharge height approx. 2,000 mm) - Automatic overbelt magnet + €5,980 net Alternatively, fixed magnetic block above the belt for manual cleaning + €990 net (for low metal contamination) - Control for conveyor and overbelt magnet + €2,750 net (start/stop synchronised with shredder); alternatively, manual start/stop for conveyors + €595 net Raw material requirements: - Moisture content (dry basis) must be below 30% - Installation temperature: temperature controlled room, at least +5°C - Metals and mineral contaminants such as sand, stones, etc., will increase wear

Condition: like new (used), functionality: fully functional, Year of construction: 2025, operating hours: 55 h, Machine with special rotor Available immediately Nledpfx Ahex Af Rdezsb Benefits: + Special rotor with reduced knife protrusion, suitable for hard and soft materials + 22 kW motor + Efficient square knives *For pallets: up to a maximum of 10 pallets per hour *Rate depends on screen size and material. Significantly higher throughput with smaller wood residues. Motor: 22 kW; 400 V - 50 Hz - 3 phase Screen: 15/20 mm or according to agreement (10 to 40 mm possible) Hydraulically operated pusher Current screen perforation (15/20 mm) *can be changed Suction connection Ø 200 mm Feed opening: 1000x1000 mm Dimensions: 2000x1800x1645 mm Sample image above: plant color may differ Weight: 1920 kg Standard scope of delivery includes: - Control cabinet with PLC control - Automatic star-delta start - High-speed hydraulics - Auto shut-off when rotor is idle - Speed 70–90 rpm for high throughput - Cycle control to prevent idle times - Performance-enhancing step control for the hydraulic pusher - Pertinax guides for hydraulic pusher - Vibration-damping machine feet - CE compliant The following options are available at an additional cost: - Increase shredder height by 30 cm (preparation for conveyor belt) + €2,480 net - Angled conveyor belt (discharge height approx. 220 cm) + €12,980 net - Overband magnet + €5,980 net - Control system for conveyor belt and overband magnet + €2,750 net (start and stop synced with shredder) - Enlarged hopper attachment 1500x1500 mm + €3,480 net Raw material requirements: - Moisture content (atro) must be below 25% - Feed must be free from metals and mineral contaminants. Tool damage and/or increased wear may result otherwise.

Condition: as good as new (ex-display), Year of construction: 2025, Special price for our demonstration machine Another machine, available now (ex works in Neckartailfingen) Approx. 8 operating hours. Suitable for shredding all types of leftover wood and also pallet sections. The pallet would need to be prepared with a jigsaw or chainsaw so that it fits vertically into the hopper - see Figure 2. Ideally, it would be approximately 40x20x20 cm so that the wood can lie flat on the slider floor. This is where the machine works most effectively. A hydraulic slider runs at the bottom of the shredder, which pushes the wood against the rotor depending on the load. The material is shredded until it passes through the screen basket. Throughput up to 200 kg per hour *depending on the screen and how well the material is prepared. *Conveyor belt and overhead magnet available at an additional cost. + Powerful 18.5 kW motor, + Concave blades, + Large high-performance gearbox, + Special, load-dependent slide control, Customs tariff number: 84659600 Motor: 18.5 kW; 400 V - 50 Hz - 3 phase Blades: 15, multi-rotatable Option: double row of blades + €995 net Rotor diameter: 260 mm Control: Siemens S7-1200 PLC Cutter opening: 630 x 820 mm Filling volume: approx. 0.6 m³ Hydraulic slide gate Screen perforation of your choice (10 - 30 mm) Suction nozzle diameter: 160 mm Weight: approx. 1,300 kg (depending on accessories) Nsdpfxodwktko Ahzelb Dimensions (L x W x H): approx. 1,737 x 1,167 x 1,650 mm Moisture content: 30% dry Included as standard: - V-rotor for maximum throughput - Control cabinet with Siemens PLC control - Automatic star/delta start-up - Fast hydraulics - Auto. OFF when the rotor is idling - Speed 70-90 rpm for high throughput - Cyclic control to avoid idle times - Performance-enhancing step control of the hydraulic slide - Pertinax guides for the hydraulic slide - Vibration-damping machine feet - CE compliant. - MADE IN GERMANY . Shredder options: - Raise shredder by 30 cm (prepared for conveyor belt) +€2,080 net - Articulated conveyor belt +€8,770 net Horizontal section: 1,200 mm Rising section: 2,500 mm Angle: adjustable from 0-60 degrees Discharge height: approx. 2,000 mm + - 100 mm - Overbelt magnet +€5,980 net - Conveyor belt and overbelt magnet control +€2,750 net (Start and stop synchronized with the shredder) - Extend hopper +€940 net - Eco-rings: +€1,980 net (recommended for more than 15% hardwood) - Special scraper +€990 net (recommended for veneer or paper) - Double Knife series + €995 net . Raw material requirements: - The moisture content (dry) must be below 30% - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear.

Condition: as good as new (ex-display), Year of construction: 2025, showroom machine machine available Advantages: + special rotor with reduced knife protrusion + Motor 22 kW + effective square knife * for pallets: up to 10 pallets per hour * depending on the sieve and material. With smaller residual wood, significantly more. Engine: 22 kW; 400 V - 50 Hz - 3 ph, Sieve: 15/20 mm hydraulically operated slide Current screen perforation (15/20 mm) * can be exchanged Nedpjdv Eu Hjfx Ahzslb Extraction nozzle Ø 200 mm. Feed opening 1000x1000 mm Dimensions: 2000x1800x1645mm Example image above: The color of the system may vary Weight: 1920 kg. Included as standard: - Control cabinet with PLC control - automatic star / delta start - fast hydraulics - automobile. OFF when the rotor is idling - Speed ​​70-90 rpm for high throughput - cycle control to avoid idle times, - performance-increasing step control of the hydraulic slide, - Pertinax guides for hydraulic slides, - vibration-damping machine feet, - CE conform. The following options are available at an additional cost: - Additional row of knives + € 2,790 - segment bottom + € 6,890 (recommended for materials with a wall thickness thinner than 3 mm) - Special K-rotor storage + € 3,480 If necessary, consider shredding plastic with sieves smaller than 15 mm or with a lot of fines. If the bearings are lubricated with grease every approx. 4 weeks in operation, this is not necessary) - Raise the shredder by 30 cm (preparation for conveyor belt) + € 2.480 net - Angled conveyor belt (discharge height approx. 220 cm) + € 12.980 net - Overbelt magnet + € 5.980 net - Control conveyor belt and overbelt magnet + € 2.750 net (Start and stop synchronized with the hacker) - Exhibition hopper 1500x1500 mm + € 3.480 net Requirements for the raw material: - The moisture content (atro) must be below 30% - The loading must be free of metals and mineral impurities. This can result in damage to the tools and / or increased wear

Condition: new, Year of construction: 2026, Single-shaft shredder MRZ 530 Included: + Profile rotor for increased throughput Options: Double knife row + €895 net Veneer and paper stripper + €970 net * recommended for extremely thin materials with a thickness less than 3 mm Our mütek single-shaft shredder MRZ 530 processes a wide variety of materials such as all types of wood residues, softwood, chipboard and MDF, pallets, construction timber, demolition wood, carpets, cables, paper, cardboard, and plastics. The machine is characterized by its robust design, ensuring consistent quality in continuous operation. We are pleased to offer you a free test with your material. You are welcome to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material via freight and we will document the test with pictures and videos. Machine data: Motor: 15 kW; 400 V - 50 Hz - 3 phase Knives: multiple reversible Rotor diameter: 260 mm Control: Siemens S7-1200 PLC Hopper (mm): 510 x 810 mm Hopper volume approx. 0.4 m³ Throughput: 1 - 5 hopper fillings/hour Nljdpfx Ahod Db N Iozeb Hydraulically operated pusher Screen perforation as desired (10 - 40 mm) Extraction nozzle Ø 160 mm Weight approx. 1,000 kg Dimensions approx. 1550 x 1100 x 1640 mm Moisture content of raw material: must be below 30% a.d. Standard features included: • Fast hydraulics • Profile rotor • Control cabinet with Siemens PLC control • Automatic star-delta start • Automatic shut-off in case of rotor idle • Removable extraction channel • Speed 70 - 100 rpm for higher throughput • Cycle control to prevent idle time • Performance-enhancing step control for hydraulic pusher • Stable guides for hydraulic pusher Additional shredder options: - Raise shredder by 30 cm (preparation for conveyor belt) + €1,980 net - Angled conveyor belt + €8,770 net Horizontal section: 1200 mm Inclined section: 2500 mm Angle: adjustable 0-60 degrees Discharge height: approx. 2000 mm ± 100 mm - Overband magnet + €5,980 net - Control for conveyor belt and overband magnet + €2,750 net (start and stop synchronized with the shredder) Requirements for input/raw material: - Moisture content (a.d.) must be below 30% - Metals and mineral impurities such as sand, stones, etc., lead to increased wear

Condition: new, Year of construction: 2026, Delivery time approx. 3-4 months MRZ 830 Shredder Custom tariff number: 84659600 Feed opening 800 x 1000 mm Motor: 18.5/22 kW; 400 V - 50 Hz - 3 ph Blades: multi-rotatable Hydraulically operated slider Nledod Dgw Uepfx Ahzjb Screen perforation of your choice (10 - 40 mm) Suction nozzle Ø 200 mm Weight approx. 1,600 kg Dimensions (L x W x H) approx. 2,290 x 1,420 x 1,750 mm Turbo clutch Included as standard: - Automatic star/delta start-up - Fast hydraulics - Auto. OFF when the rotor is idle - Speed 70-90 rpm for high throughput - Cycle control to avoid idle times - Performance-enhancing step control of the hydraulic slide - Pertinax guides for the hydraulic slide - Vibration-damping machine feet - CE compliant . The shredder is designed for shredding natural wood, particle board, and MDF, as well as other materials after testing and approval by the manufacturer. Additional shredder options: - Raise shredder by 30 cm (prepared for conveyor belt) + €2,140 net - Articulated conveyor belt + €8,770 net Horizontal section: 1,200 mm Rising section: 2,500 mm Angle: adjustable from 0-60 degrees Discharge height: approx. 2,000 mm + - 100 mm - Overbelt magnet + €5,980 net - Conveyor belt and overbelt magnet control + €2,750 net (Start and stop synchronized with the shredder) Raw material requirements: - Moisture content (dry) must be below 30% - Installation temperature: temperature-controlled room at least +5°C - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear

Condition: new, Year of construction: 2025, The ideal machine for shredding hardwood and softwood Another machine now available (ex-works Neckartailfingen). Motor: 18.5 kW; 400 V - 50 Hz - 3 ph, Blades: 14+2 pieces, 40x40mm, reversible multiple times, Rotor diameter: 260 mm, Control system: Omron PLC, Cutting chamber opening: 600 x 800 mm, Hopper volume approx. 0.6 cbm, Hydraulically operated pusher Screen perforation of your choice (12 - 40mm) Extraction socket Ø 160 mm Weight approx. 1,300 kg Dimensions (LxWxH) approx. 1737 x 1167 x 1650 mm The following options are available at an additional cost: - Additional row of knives + €1,990 net (28 instead of 14) - Surcharge for segmented floor, 4-sided + €2,170 net (prevents the pusher from jamming. Recommended for materials with a thickness of less than 3 mm) - Raise shredder by 30 cm (preparation for conveyor belt) + €1,980 net - Angled conveyor belt (discharge height approx. 220 cm) + €8,770 net - Overband magnet + €5,980 net - Control system for the conveyor belt and overband magnet + €2,750 net (start and stop synchronized with the shredder) - Special bearing + €1,540 net (rarely required. Closed, even more robust rotor bearing. May be considered for screens smaller than 15 mm or high fine content. Not necessary if bearings are greased approximately every 2 weeks in operation) Requirements for raw material: Nedpsd E R D Sofx Ahzjlb - The moisture content (atro) must be below 30% - Metals and mineral contaminants such as sand, stones, etc. increase wear. We are happy to offer a free test with your material. We invite you to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material via freight company and we will document the test with photos and videos.

Condition: new, Year of construction: 2024, production time appr. 4 months * for suction perception, see picture 4 and 5 Tariff number: 84659600 Main motor: 55 kW; 400 V - 50 Hz - 3 ph including turbo coupling, Njdpfod Hkqhex Ahzslb Hydraulic motor: 2.2 kW, 400 V - 50 Hz - 3ph Knife: 76 pieces, rotatable Knife size: 35 x 35 x 20 mm Rotor diameter: 360 mm Control: PLC Siemens S7-1200 Funnel opening approx. 1530 x 1235 mm Hopper volume approx. 2.5 square meters hydraulically operated slide Screen perforation: 10 - 30 mm Extraction nozzle Ø 200 mm Weight approx. 4,500 kg Dimensions (lxwxh) approx. 2765 x 2520 x 1730 mm Turbo coupling Included as standard: - V-rotor for other throughput - 2nd row of knives on the rotor - Control cabinet with Siemens PLC control - automatic star / delta start - fast hydraulics - Automobile. OFF when the rotor is idling - Speed ​​70-90 rpm for high throughput - Clock control to avoid idle times - Performance-increasing step control of the hydraulic slide - Pertinax guides for hydraulic slides - anti-vibration machine feet - CE conformity The shredder is for shredding natural wood, chipboard and MDF board other materials after testing and approval by the manufacturer Recognition from the raw material: - The moisture content (atro) must be below 30% - Metals and mineral impurities such as sand, stones, etc. Interests to interests wear

Condition: new, Year of construction: 2026, The ideal machine for shredding softwood. Motor: 11/15 kW; 400 V - 50 Hz - 3 ph, Nodpfx Aewzarcohzolb Rotor diameter: 260 mm, Hydraulically actuated pusher Screen perforation to choice (12 - 40 mm) Extraction port Ø 160 mm Weight approx. 1,100 kg Dimensions (LxWxH) approx. 1805 x 1118 x 1650 mm Colour: blue / grey Requirements for raw material: - Moisture content (atro) must be below 30% - Metal and mineral contaminants such as sand, stones, etc. lead to increased wear. We are pleased to offer a free test with your material. You are welcome to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material by freight and we will document the test with photos and videos.

Condition: used, Shredding Machine MGZ 1330, 37 kW Operating hours: 275 Included: - Second knife row - Fast hydraulics for increased throughput - Preparation for conveyor belt Optional: - Conveyor belt with automatic metal separator Your advantages: + Extremely large cutting chamber opening; top: 1300x1200mm + Special rotor suitable for both hardwood and softwood + Energy-efficient and powerful, 37 kW start-up power Nodpfjx Tfdhjx Ahzjlb Technical data: Feed opening, top (mm): 1,300 x 1,200 Hopper capacity (cbm): 1.6 m³ Rotor diameter (mm): 368 Rotor speed (rpm): 65 - 125 Power requirement (kW): 37 Screen hole size (mm): configurable Tools: 37/70 knives Extraction connection diameter (mm): 200 mm Dimensions: 2430x2410x1735 mm (LxWxH) Weight (approx. kg): 3,500 --- Feedstock requirements: - The moisture content (atro) must be below 20% - The feed material must be free of metals and mineral contamination. Damage to the tools and/or increased wear may result.

Condition: used, Belt Conveyor, Belt Conveyor System, MFP Conveyor Technology Machine No.: 17565 Year of Manufacture: 2018 Usable length: 3100 mm Belt width: 600 mm Belt length: approx. 6400 mm Frame profile height: 35 mm Deflection roller diameter: 20 mm Belt speed: 10 m/min to 45 m/min Conveyor height: approx. 1120 mm Motor power: 140 Watts Power supply: 230 Volt, 50 Hz - Infinitely variable belt speed via potentiometer on ROFRE frequency inverter, type 897 - Reversible operation (right/left running) - Belt drive via INTERROLL drum motor Nlsdjwrihnopfx Ahzeb - Stable sheet steel construction with closed steel plate under the conveyor belt - 1 piece height adjustable subframe HAACON with hand crank, conveyor height approx. 950 to 1150 mm - HAACON subframe mounted on steel plate, length 750 mm x width 500 mm x thickness 30 mm - 1 fixed support foot without height adjustment as transport support - Fully mobile on fixed castors Overall dimensions L x W x H: 3180 x 760 x 1150 mm Weight: 250 kg Good condition

Condition: used, Conveyor belt, belt conveyor, belt conveyor, belt conveyor MFP Fördertechnik Machine No: 20083 Year of manufacture: 2021 Usable length: 2800 mm Belt width: 360 mm Usable width: 300 mm Belt length: approx. 5800 mm Frame profile construction height: 70 mm Deflection roller diameter: 20 mm Belt speed: 10 m/min to 48 m/min Conveyor belt height: approx. 1150 mm Motor power: 140 Watt Power supply: 230 Volt, 50 Hz - Stepless belt speed via potentiometer on ROFRE frequency converter, type 897 - Right-left run - Belt drive via INTERROLL tube motor - Stable steel sheet construction with closed steel plate under the conveyor belt - 1 piece height-adjustable substructure with hand crank, conveyor belt height approx. 1000 to 1200 mm - Substructure mounted on steel plate length 500 mm x width 500 mm x thickness 30 mm - 1 piece fixed support foot without height adjustment as transport support - Fully mobile on fixed castors Overall dimensions L x W x H: 2880 x 500 x 1150 mm Nljdpfswqg Enox Ahzeb Weight: 200 kg good condition

Condition: new, Year of construction: 2026, Availability upon request Nljdpfxed Nm Sis Ahzob Very robust machine with high pressing force - also suitable for producing briquettes of saleable quality *depending on the material. The large pressing cylinder and the 70 mm briquette make this possible. Our best-selling briquetting press series + Proven, simple technology for extremely low susceptibility to errors + 25 years of experience, further development, and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Supplement for demonstration cooling unit + €4,980 net, (can also be retrofitted later) * Cools the pressing tongs (important for use after 4 hours) and the hydraulic oil * Cooling unit recommended for regular use of more than 4 hours at a time. Tariff number: 84793010, Briquette diameter: 70 mm, Front bushing: 125 mm, Max. briquette stroke: 100 mm, Optional briquette stroke: 80 mm, Capacity (depending on material): up to 150 kg/h* *depending on bulk density, *based on a bulk density of 200 kg per cubic meter. . Motor power: 9.2 kW, 400 volts / 50 Hz / 3-phase, Length: 2095 mm, Width: 1300 mm, * with large chamber 1600 mm Height: 1700 mm, Weight: 1250 kg, Oil capacity: 220 liters, Silo diameter: 1200 mm Silo capacity: approx. 1 cubic meter Pump: 75 liters Hydraulic pre-compressor Cooling option for pressing tongs: yes, with optional coolable pressing tongs Cooling option for hydraulic oil: yes Cooling of the pressing tongs and hydraulic oil with a cooling unit (optional accessory) Level monitoring option: yes Extruded briquette option; Yes (depending on material) Optional enlarged feed slide: Yes, with special accessory enlarged feed slide CE compliant Raw material requirements: - The moisture content (dry) must be between a minimum of 6% and a maximum of 18% - Maximum chip length: 20 mm - Installation temperature: Temperature-controlled room at a minimum of +5°C - The feed must be free of metals and mineral contaminants such as sand, stones, etc. This may result in damage to the press tools and/or increased wear.

Condition: new, Year of construction: 2026, Our best-selling briquetting press, the classic. + Tried and tested, simple technology for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Options for an extra charge: * Surcharge for the level indicator that enables automatic operation + € 995 net * Surcharge for large pre-compression chamber + 980 € (recommended for light material like straw) Briquette diameter: 50 mm Front bush: 50 mm Briquette stroke max .: 40 mm Briquette lift opt ​​.: 40 mm Throughput (depending on material): 30-60 kg / h * * depending on the bulk weight * based on a bulk weight of 200 kg per cubic meter . Motor power: 5.5 kW 400 volts / 50 Hz / 3 phases Length: 1680 mm Width: 1100 mm Height: 1500 mm Weight: 680 kg Oil volume: 110 liters Silo diameter: 1000 mm Silo content: approx. 0.7 square meters Pump: 27 liters Hydraulic pre-compressor Option cooling pressing tongs: no Hydraulic oil cooling option: yes Level monitoring option: yes CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18% Nodogl Nlmjpfx Ahzjlb - Maximum chip length 15 mm - Installation temperature: temperature-controlled room at at least + 5 ° C - The customer must insure himself against loss of hydraulic oil - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: new, Year of construction: 2026, Diameter: 160mm Also available in the diameters: 180, 200, 250, 300 mm for an additional charge, other diameters on request. Njdpfx Ajchuvrshzelb Very stable industrial design. Ideal for separating nails/metal parts from material flows. For example after a wood shredder. including 3 extremely powerful magnets * If desired, up to 6 magnets can be installed in the component - surcharge for each additional magnet + 49 € - Neodymium magnets are also available instead of ferrite for an additional charge Your advantages: + Extremely large inspection door with seal for easy stripping of the nails + Stable quick-release fastener +Made in Germany Inspection door / opening: 35x18 cm Installation length may vary

Condition: new, Year of construction: 2025, Another machine immediately available! Briquetting press with PLC control and automatic briquette length adjustment Throughput: up to max. 60 kg/h Briquette: 50 mm cylindrical Motor: 5.5 kW Dimensions: 1,900 x 1,350 x 1,410 mm Weight: approx. 860 kg Requirements: Feed material should ideally be shorter than 25 mm chip length Moisture content 6–12% ATRO Machine suitable for intermittent operation. E.g. briquetting for up to 2.5 hours; 1 hour break, etc. If the machine needs to run longer than 2.5 hours continuously, optional cooling must be connected. Nlsdpfx Ahsv Rpxlszsb

Year of construction: 2026, condition: new, *Only the neodymium overbelt magnet is offered, not the conveyor belt underneath. *Neodymium magnets are among the strongest magnets in the world. They have an extreme pulling power and cannot be compared to ferrite magnets. Extremely high degree of separation, depending on the bulk height and the starting material. Probably the most compact overband magnet on the market. The competition often uses the less powerful ferrite magnets to save costs. dimensions approx. Length: 104cm Width: 22cm Height: 28 cm (at the motor) *Without controller Surcharge for simple manual start/stop control + 495 € A high-performance industrial neodymium magnet is installed. High-performance neodymium magnet approx. 600x68x36.5 mm * So nails are attracted to a length of 600 mm and thrown off to the side, in the area that is no longer magnetic. This overbelt magnet should be mounted approx. 5 - 9 cm above the material flow. *Assembly/suspension on site Ideal for separating nails from wood chips. Optionally also in a single-shaft shredder that is sucked off Nlsdpfx Ahjdubpuszsb Requirements: *Your belt width or useful width inside (of the existing conveyor belt) should ideally be narrower than 55 cm *Suitable for separating nails from material flows that are less than 12 mm high and with a chip length of less than 25 mm. ----- Optional at extra charge: Cross and ascending belt demonstrators from € 7,995 net

Condition: new, Year of construction: 2026, Briquetting press NEM 900: production time appr. 5 months for briquetting aluminum chips Throughput: up to maximum 320 kg / h * more details after a free test with heard material . Briquette diameter: Ø 70 mm Optimal briquette length: 70 mm . Technical specifications: Total connection: approx. 31 kW In continuous operation approx. 22 kW 400 volts / 50 Hz / 3 phases Pump: 120 + 60 liters per minute Silo: 1 m³ Silo rollers: 1200 mm Including agitator Nlsdpfx Aogfm Ryohzeb Oil tank: 600 liters Dimensions: 2500 x 1700 x 1730 mm lxwxh Weight: 2250 kg. Hydraulic pre-compression via slide Main press cylinder Vertical cylinder Above for connecting a cooling unit . One and the source material - max.span: 18 mm - Excessive temperature: temperate room at at least + 5 ° C. - max.weight on agitator: 200kg. - The loading must be free of metals and mineral impurities such as sand, stones, etc. This on the pressing tools and / or responsible wear can result