Used Ball for sale (2,870)

Condition: new, maximum load weight: 39,850 kg, overall weight: 45,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the specifications. Full equipment details available upon request. Chassis: - Welded construction from high-quality steel sections with through-profile cross members Rsdswx Dbpepfx Al Iet - Designed for high point loads. Outer frame as UNP profile - Fifth wheel plate approx. 8 mm, underride guard nose approx. 700 mm wide - Bracket at front for customer-side mounting of a support device, approx. 90 x 90 x 4 mm Coupling device: - 2-inch kingpin (mount also suitable for 3.5) Rear underrun protection: - According to EC, bolted design Side underrun protection: - According to EC Landing gear: - 24 t landing legs with single-side operation (test load approx. 66 t), Jost Modul CH (Heavy Duty) S-foot Axles: - 3 x 9 t air suspension axle units, manufacturer of our choice, with disc brake approx. 430 x 45 mm - ABS - Hub-centric wheel mounting, 10-hole, ET 120 - Total air suspension travel approx. 200 mm, of which raising approx. 140 mm and lowering approx. 60 mm, controlled via rotary slide valve with detent, with RTR function - Switch for second ride height (+ approx. 50 mm) on the bracket of the lifting and lowering device - Smartboard/TIM/Infocenter, without TPMS display Lifting axle: - First axle liftable, with fully automatic load-dependent lift control, starting aid via button in the driver’s cab (15-pin socket PIN12). Button in cab not included in delivery Braking system: Manufacturer of our choice - Two-line compressed-air braking system according to EC with EBS and RSS, automatic load-dependent adjustment - Spring brake cylinder as parking brake - Mistake-proof coupling heads mounted securely on front cross member, without connecting line to the motor vehicle Tyres: - 6 units, 385/65 R22.5 160J on 11.75 x 22.5 rims (manufacturer of our choice), ET 120 - Basic version tyre pressure monitoring, connected to EBS CAN-bus system - Tyre pressure display in driver’s cab (pre-installed by truck manufacturer) Mudguards: - According to EC, PVC mudguards (half-shells) over all axles - Anti-spray mudflaps Load securing: - 8 pairs of lashing plates welded into the outer frame (pulling force approx. 3 t) - 6 pairs of lashing rings on the side of the outer frame, evenly distributed (pulling force approx. 10 t) - 13 pairs of lashing eyes (bails) on the outer frame (tested lashing capacity approx. 2.5 t per point) Stake pockets/stakes: - 5 pairs of stake pockets recessed in the outer frame, approx. 90 x 90 x 4 mm - 3 pairs of stake pockets recessed in the loading floor, approx. 90 x 90 x 4 mm - 10 plug-in stakes made of galvanized box section, approx. 80 x 80 x 4 mm, with stop at the bottom Front wall: - Bolted front wall, approx. 1,200 mm high, covered with approx. 5.5 m sheet metal Stake magazine: - Inside the front wall, a magazine for plug-in stakes Floor: - Approx. 28 mm hardwood floor recessed in the outer frame, with galvanized omega steel profiles Lighting system: - According to EC, 24 volts with multi-chamber taillights - LED side marker lights - LED front position lights white - LED rear outline marker lights - Number plate lights - 1x 15-pin and 2x 7-pin socket connectors on the front cross member Equipment: - Chock with double holder - Warning sign according to ECE 70 - 2 LED work lights on the lamp bracket (switched by reverse gear) - Bracket for optional rotating beacon at rear (incl. beacon) - 1 foldable and extend

Condition: new, maximum load weight: 52,810 kg, overall weight: 63,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of immediately and soon available vehicles on our website. Excerpt from the equipment list. Full specifications available on request. Cargo area: * Cargo area with approx. 30 mm thick hardwood floor * 10 pairs of folding external lashing rings (LC 10,000 daN) Landing legs: * Hydraulic landing legs TPMS: * TPMS tire pressure monitoring system compliant with ECE R 141. Data transmission to the tractor unit is via the standardized EBS interface according to ISO 11992. For correct display, the tractor must be capable of transmitting and displaying these data. Axles and suspension: * BPW axles, technical capacity 12,000 kg each, first axle fixed, all others hydro-mechanically forced-steered, mounted on turntables * Air-suspended with lift and lower valve * Axle toolkit Tires: * Tires 445/65 R 22.5 169 K Electrical system: * Electrical system in accordance with EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets * Connections according to standards. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Brake system: * Wabco brake system compliant with EU regulations, with EBS-E (4S3M), without connecting lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield point 355MPa), S690QL/S700MC (yield point 690MPa) Painting: * Complete steel structure automatically shot-blasted after welding using a shot-blasting machine * Secondary blasting with corundum for optimal adhesion of the coating system * Final painting with 2 coats of 2K topcoat, single color in RAL 1007 Narcissus Yellow according to RAL system 841GL * Rear section metallized and painted in RAL 9010 Pure White * Wheels in Silver Grey * Paint structure tested in salt spray test according to ISO 9227-NSS * Cavity sealing with special wax Rsdpfsxttc Asx Al Ijt Including accessories: * Cargo area with approx. 30 mm thick hardwood floor * 2-inch king pin * One galvanized steel front wall (EN12642-XL), approx. 1,200 mm high * Yellow-red air couplings on the galvanized front connection strip * On the gooseneck and rear panel left and right, each with a bracket for warning signs including socket * Rear steering from the front and rear by cable remote control via push buttons, with single-track control of the axles (without installation in the tractor unit) * Electro-hydraulic unit * 12 pairs of stake pockets for approx. 100 x 50 mm stakes in the outer frame of the cargo area * Load manometer for determining axle loads including load diagram * Lift axle on the front axle, controlled by TEBS E * 5 pairs of crosswise stake pocket rails on the cargo area, for approx. 100 x 50 mm stakes * One INOX toolbox 1,200 x 460 x 550 mm mounted at the front left under the cargo area (in direction of travel) * 1 shunting coupling with reinforcement bolted to the rear cross member * BEKAMAX (Pico) automatic central lubrication system with standard grease NLGI-2 and removable pump guard * 2 LED reversing lights mounted on the rear panel * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum)

Condition: used, functionality: fully functional, total length: 1,000 mm, load capacity: 2,500 kg, Bale Clamp Condition: Ready for use and fully functional Technical Condition: good Description: Bale Clamp / Rotating Clamp – suitable for forklifts Lifting Capacity: 2,500 kg | Condition: good, fully operational Robust bale and rotating clamp designed for professional use in warehousing, recycling, manufacturing, and paper handling. The unit is fully functional, immediately ready for operation, and in good technical and visual condition. Technical Data: Type: Bale clamp / Rotating clamp Capacity: 2,500 kg Length: approx. 1,000 mm Opening width: as specified by device (see photos / inspection) Back width: on request Projection: on request Redpfx Ajx Aw Sysl Ijt Dead weight: on request Condition: technically good, visually good Location: available immediately Notes: Sale as-is in current used condition. All prices are net plus 19% VAT. Sale exclusively to commercial buyers with valid VAT ID. No warranty or guarantee. Charger note does not apply to attachments, but is systemically retained.

Condition: used, mileage: 2,165 km, power: 130 kW (176.75 HP), first registration: 07/2025, fuel type: diesel, overall weight: 3,500 kg, next inspection (TÜV): 07/2026, gearing type: automatic, emission class: euro6, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), navigation system, All-season tires, LED lighting, rear step across half width, rear wing doors without window cutouts, right sliding door, multifunction steering wheel, double passenger bench seat, hill start assist, emergency braking, lane change and crosswind assist, rear view camera, ASR, DAB+, USB, MAN Media Van navigation, mobile phone interface, wooden flooring in cargo area with rear loading edge protection, C-rails on side walls, partition wall, lashing eyes. Rsdpfeyg Twzsx Al Ijt

Condition: used, Year of construction: 2022, Bale fork M140 EURO Zinc set 2PCS 820 mm KON2 Zinc set 2 PCS 1240 mm KON2 / Redetrdl Eepfx Al Iet

Condition: used, Year of construction: 2023, Tandem axle Air brake PTO shaft 20-piece / Varioterminal 9-inch bale chute / / Redotlrnaopfx Al Iet

Condition: used, Year of construction: 2023, Zinc set 2 PCS 1240mm KON 2 / Rodot Srdispfx Al Iet

Condition: used, Year of construction: 2002, Operating terminal / Rjdpfx Aoufxr Eol Ijt

Condition: used, maximum load weight: 24,500 kg, overall weight: 34,000 kg, axle configuration: 3 axles, first registration: 01/1995, Year of construction: 1995, Equipment: ABS, BABELSBERGER SSA 51 SAF AXLES BALLAST TRAILER 14 STANCHIONS 1ST OWNER ----VEHICLE HISTORY * GERMAN VEHICLE * VIDEO AVAILABLE ON REQUEST VEHICLE EQUIPMENT * TYPE: SSA 51 / 124/1 * BALLAST SEMI-TRAILER * 3 AXLES * DRUM BRAKES * AIR SUSPENSION * 14 STANCHIONS * LOAD SECURING EYELETS * TIRE SIZE: 445 / 65 R 22.5 * GROSS VEHICLE WEIGHT: 34,000 KG * UNLADEN WEIGHT: 9,500 KG * PAYLOAD: 24,500 KG * IMMEDIATELY READY FOR USE---- * EXPORT SALES ONLY WITH DEPOSIT (MIN. €500 - €2,000) ----EXPORT DECLARATION CUSTOMS EXW IN 10 MIN. (APPROVED EXPORTER) 5 DAY, 30 DAY LICENSE PLATES AND 17-21 DAY AUSTRIAN LICENSE PLATES EURO 1 VEHICLE RESERVATIONS ONLY VIA EMAIL FUNCTION VERBAL RESERVATIONS ARE NOT VALID! For sales to the EU & third countries, a deposit of at least €500.00 / €1,000.00 will be charged. Modifications, errors and prior sale excepted! You can find more vehicles on our homepage: Rjdpfetvt A Tjx Al Iet Sale is subject exclusively to our terms and conditions – see homepage Important notice – Important information: Despite thorough verification of all details in our offer, errors may occur. In some cases, these are caused by transmission errors in the systems of different platform providers. Therefore, we would like to point out that all information provided is without guarantee and does not constitute a legal claim. Legal notice: This advertisement does not constitute an offer within the meaning of §145 BGB but is merely information to initiate a contract. All information is provided without guarantee and does not represent warranted characteristics.

Condition: used, mileage: 1,054,044 km, power: 353 kW (479.95 HP), first registration: 02/2008, fuel type: diesel, overall weight: 26,000 kg, axle configuration: 3 axles, brakes: retarder, color: white, gearing type: mechanical, emission class: euro4, loading space length: 5,650 mm, loading space width: 2,450 mm, loading space height: 2,700 mm, Equipment: ABS, air conditioning, all wheel drive, * MAN TGA 26.480 6x4H - 2BL Hydrodrive All-wheel drive 4x4 * Flatbed with tarpaulin and wooden stakes * Air conditioning * Manual transmission Rjdpfx Aekq Ap Tol Iet * Auxiliary heater * Removable crane mount * 6-stage retarder * 2 beds * Electric windows * Electrically adjustable mirrors * Trailing axle / with articulated axle * VIN: WMAH35ZZ38L050607 * Engine type: D2676LF05 * kW: 353 * Euro 4 * Displacement: 12,419 cc * Unladen weight: 14,580 kg * Payload: 11,345 kg * Gross vehicle weight: 26,000 kg * Wheelbase: 4,500 / 1,300 mm * Body internal length: 5.65 m * With tailgate open, internal length: 6.40 m * Body internal width: 2.45 m * Body internal height: 2.70 m * Vehicle length: 9,250 mm * Vehicle width: 2,550 mm * Vehicle height: 4,000 mm * Tires: 385 / 65 R 22.5 * Net price Tel./WhatsApp:

Condition: used, Year of construction: 2009, Manufacturer: H&G Model: HG/SV 11 Weight: 1800 kg Rodox Hyfyjpfx Al Iot Engine power: 11 kW

Condition: new, Reglaj Attachment( Ballast Leveling Bucket) Designed to improve sub-rail stability, our Reglaj Attachment is used for ballast leveling operations. Rsdpfx Aov Spfzel Iet For more detailed information, please feel free to contact us.

Condition: new, functionality: fully functional, Year of construction: 2025, Aggregate and ballast crusher equipment are used in the crushing and processing of various materials for construction and infrastructure projects. These crushers are designed to break down large rocks, gravel, or stones into smaller pieces, producing aggregates and ballast that are essential components in the construction industry. Here are some key aspects related to aggregate and ballast crusher equipment: 1. Jaw Crusher: - Jaw crushers are commonly used for primary crushing in aggregate and ballast production. They operate by compressing the material between a stationary and a movable jaw. 2. Impact Crusher: - Impact crushers are suitable for shaping and producing fine aggregates. They use impact force to crush the material, making them suitable for various types of rock and ore. 3. Cone Crusher: - Cone crushers are often used for secondary and tertiary crushing in aggregate production. They are efficient for producing well-shaped and finely graded aggregates. 4. Vertical Shaft Impact (VSI) Crusher: - VSI crushers are designed for shaping and producing high-quality artificial sand. They use the "rock-on-rock" crushing principle, where rocks are fed into the rotor to be accelerated and crushed against the stationary anvils. 5. Gyratory Crusher: - Gyratory crushers are primarily used in mining, but they may also be used in the production of aggregates. They have a conical head and a concave surface, which crushes the material between the head and concave. 6. Mobile Crushers: - Mobile crushers, including mobile jaw crushers and mobile impact crushers, provide flexibility and mobility for on-site crushing of aggregates and ballast. They are often used in construction projects where materials need to be processed directly at the job site. 7. Screens and Scalpers: - Screens and scalpers are used to separate different sizes of aggregates after the initial crushing stage. Vibrating screens are commonly employed to classify and separate materials based on size. 8. Conveyors: - Conveyors are crucial for transporting materials between various stages of the crushing process and for stockpiling the final products. They enhance efficiency in material handling. 9. Dust Suppression Systems: - Crushing operations can generate dust, and dust suppression systems are used to minimize environmental and health impacts. These systems may include water sprays or chemical suppressants. 10. Quality Control: - Quality control measures, such as particle size analysis and gradation testing, are essential to ensure that the produced aggregates and ballast meet the required specifications and standards. 11. Environmental Considerations: - Crusher equipment should adhere to environmental regulations, and measures like dust control, noise reduction, and proper waste disposal should be implemented. Rjdpfx Aleq Nxrxs Ist When selecting aggregate and ballast crusher equipment, factors such as the type of material, required product size, production capacity, and mobility requirements should be taken into consideration. Additionally, adherence to safety and environmental standards is crucial in the operation of crushing equipment.

Condition: used, Year of construction: 2015, functionality: fully functional, machine/vehicle number: 22359, Equipment: UVV, Compact design allows storage and transport in the smallest of spaces. The ideal solution when large amounts of light are temporarily needed. Suitable for all types of lighting applications, such as construction sites, roadworks, events, film and photography, or securing hazardous areas. The light balloon can be mounted on work machines and thus ideally illuminates the operating area of the equipment. Energy-saving LED technology with high light output. Rjdpfx Aloxn S Duj Ist

Condition: excellent (used), - Dimensions: 2480x1000x1450 mm - Year: 2006 - Packaging material: PVC, polyolefin, polyethylene, polypropylene - Maximum product length: 680 mm - Maximum product height: 220 mm Rodpfx Ajwyc Udjl Ist - Product weight: 0.25–10 kg - Maximum roll diameter: 600 mm - Sealing arm dimensions: 490 x 390 mm - Voltage: 400V - Weight: 360 kg - Overhauled equipment: The machine is prepared upon order; collection and return times are arranged at that moment (please request the price after overhaul).

Year of construction: 2024, condition: new, Overview - of the different variants *Not every position is required: Optional: Rodpfxoff Sbij Al Iet -Bale shredder MHB from 24.990 € net -MHZ straw mill from € 7,980 net -Special hopper 970 € net -Cyclone from € 3,750 net -Sheet metal silo demonstrator with discharge (only sketched in the picture) *optional, if you want to load with the wheel loader Unit price net from € 14,750 - Demonstrator -Dedusting auger - length approx. 4 m 4 sieves are mounted on the underside, which are extracted. Unit price net from: 9.750 € - Extraction parts / hoses flat rate 945 € net - Complete control system Net unit price: € 2,750 -Demonstrator extraction unit MMJET 160 Demonstrator, with cleaning Connection 160, fan 2,2kw air capacity 1850m³ /400 V Automatic compressed air cleaning Unit price net from: 6.950 € -Baler B 400 Bales approx. 400x400x800 (height adjustable) Up to 30 bales per hour with + - 20 kg from 59.995 € net *A reference system (baler) is located in zip code: 64579 Gernsheim Technical data: Bale size (WxDxH): 400 x 400 x 800 (height can be adjusted on request) Bale weight +/- 20 KG (depending on material) Capacity: approx. 30 bales per hour Storage container approx. 0.7m³ capacity Filling level sensors for min./max. filling level in the container Hydraulic pre-compressor Hydraulic compression ram Hydraulic unit, valve block with oil tank Pump 18.5 KW / 50 liters Rollers in the bale chamber for easy bale push-off Dimensions (l x w x h) 3105x2830x2455 mm Weight approx. 1500 KG mütek baling presses / wrapping machines are designed for the production of bales from a wide variety of materials such as shredded micanthus or elephant grass, wood chips, sawdust and shredded straw. straw. The machine is characterized by a robust design that guarantees consistent quality in continuous operation. quality in continuous operation. The baler compacts the material filled into the storage container without the addition of binding agents and packs the material into plastic bags. The volume of the material can be considerably with the baling press. The volume reduction rate depends on the material. The maximum material moisture content must not exceed 18 % Atro. The container of the mütek baler can be fed automatically or manually and has a volume of approx. 0.7 m³. volume of approx. 0.7 m³. Containers with a larger volume or with an attached suction and filter system as a complete disposal unit are also available. In addition to automatic filling via deduster, mütek also offers filling by means of screw conveyors. With both variants, automatic automatic dedusting is possible. mütek baling presses are equipped with a control cabinet for the control system. In the standard version, the dimensions of the bales (width x depth x height) are 400 x 400 x 800 mm. However, the height can be adapted to your requirements on request. The following advantages arise in the production of bales: - simple and safe storage - No loose dust - Minimization of the storage volume - Low transport volume *Requirements for source material: - dry (max. 30 % ATRO) - Maximum length 35 mm

Condition: new, Year of construction: 2026, Ballshaping- and Delaminationmill Redpfx Aedwqiuel Ijt Molinator for fine delamination! Diverse Types: RW VKR16/3 / 22-37kW and RW VKR 22/3 / 75-110kW Input Composite Material Examples: Regrind from hair-wire, printed circuit boards, electronic circuits, other composited material. Al / Plastic, Cu / Plastic, Cu / Glass fibre, ABS / Plastic fibres, etc. Type selection: depending on the material / depending on layer thickness / depending on test‘s / according to the desired throughput. Description Molinator: In the inner acts very high forces (High acceleration / high relative-speed)! Bigger parts will be delaminated. Composite-material separates at the phase of boundaries. Metals will be ballshaped. Plastics depending on the specifications stays “fluffy” or will be grinded. These effects besides the desired delamination, are helpfully for the separation and are exactly coordinated to our separation-technology like Fluid Bed Separators / Sievemachines / Sifters.

Condition: ready for operation (used), 1) Electr. engine 5 kW Redeiau S Depfx Al Ist 2) Vibrating dispenser, 3) Original STADLER construction (approximately 12 tons) Everything works and is ready to work - to check on site. Video on demand. Location; Poland

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2007, machine/vehicle number: 621307509, actuation type: hydraulic, controller model: Delem DAC-350, working width: 3,080 mm, sheet thickness (max.): 10 mm, TECHNICAL DETAILS Max. sheet thickness: 10 mm Max. working width: 3,080 mm Cutting speed: 20 mm/min MACHINE DETAILS Control: Delem DAC-350 Drive type: Hydraulic Redpjy Avu Njfx Al Ist Power: 30.0 kW Dimensions & Weight Transport dimensions (L x W x H): 4,985 x 2,400 x 2,200 mm Weight: 11,500 kg Transport packages: 1 pc. EQUIPMENT Backgauge type: Electric Sheet support system: Pneumatic Finger guard: Fixed with flip-up safety guard Angle adjustment: Motorised Cutting gap adjustment: Motorised Table type: Ball table Documentation CE marking

Condition: ready for operation (used), Year of construction: 2004, operating hours: 61,082 h, functionality: fully functional, travel distance X-axis: 2,800 mm, travel distance Y-axis: 1,200 mm, travel distance Z-axis: 800 mm, controller model: HEIDENHAIN TNC 426, Equipment: chip conveyor, In January 2025, a new spindle was installed! The machine has been regularly maintained! TECHNICAL DETAILS Travel range X-axis: 2,800 mm Travel range Y-axis: 1,200 mm Travel range Z-axis: 800 mm Feed rates Rapid traverse: 35,000 mm/min Spindle speed S1 (continuous duty) Vertical: 10,000 rpm Spindle speed S1 (continuous duty) Universal swivel head, 2 axes: 18,000 rpm MACHINE DETAILS CNC Control: HEIDENHAIN TNC 426 Electrical data Supply voltage: 400 V (–15 %, +10 %) Frequency: 50 Hz Current draw: 101.1 A Installed total power: 59.8 kW Operating hours Power-on hours: 98,755 h Program run time: 61,082 h Rjdpjy Dgyfsfx Al Ijt EQUIPMENT High-rigidity gantry design from the FPT DINO series Precision linear guides and ball screws Spacious work area with 2.8 m X-axis travel High feed rates for efficient machining Ideal for tool, mold, and machine construction Includes documentation and acceptance certificate according to ISO standards Tool changer Coolant system Chip conveyor Interchangeable milling head with 4th/5th axis

Condition: ready for operation (used), functionality: fully functional, repeat accuracy: 0.002 mm, table load: 50 kg, rotary table diameter: 500 mm, The offer consists of the following components: VL-770 Probe Head – High-resolution optical 3D scanner VL-700 Control Unit – Control and evaluation unit, including software interface Redpfx Aljy Eglqe Iot VL-C35 Cover – Light protection hood VL-A3D Software Package – Measurement and evaluation software (German) OP-88145 Calibration Plate – Reference plate VL-H3G Module – Geometric dimensioning and tolerancing (GD&T) module VL-H3R Module – CAD conversion module VL-B1 Accessory – Calibration ball gauge OP-99031 Cable – AC power cable TECHNICAL DETAILS Repeatability (σ): 2 µm Measurement accuracy: ±10 µm Measurement resolution: 9 million measurement points Measuring range Low magnification: Ø300 × H200 mm High magnification: Ø70 × H50 mm Work Table Rotary table: 500 mm Rotation mechanism: 360° XY movement of object stage: Ø200 mm Tilting mechanism: up to 45° Maximum load capacity: 50 kg MACHINE DETAILS Weight Weight of control unit: 3.7 kg Weight of object table: 26 kg Weight of cover: 5.5 kg Weight of measuring unit: 19.6 kg EQUIPMENT Original software and manuals Calibration plate Protective hood Monitor, PC, keyboard, and accessories

Condition: used, Year of construction: 2007, Fully programmable 3 axis horizontal CNC swing chisel mortiser suitable for general joinery and furniture production. By a combination of automatic movement of the mortisting head in the x axis and an automatic gripper that positions the timber no manual movement or handling of the component is required other than loading and positioning the timber against the pneumatic reference stop and then unloading when the mortising cycle is finished. The complete movement, clamping and, mortising cycle is fully automatic. X, Y and, Z axis movements are all via re-circulating ball and screw drives and using linear slideways to give maximum positioning accuracy. Thanks to the programmable Z axis it is possible to produce off line mortises, double mortises or produce thicker mortise slots with the same chisel. Programming is very simple thanks to the 'user friendly' graphic touch screen controller were programs can be memorised and stored under a number or specific name up to 8 characters. The swing chisel cutter itself produces a very clean mortise slot and if required for deep mortises up to 3 depths of cut can be programmed to give a 'woodpecker' type cutting operation. Other programming options include working off either the face of the timber or the thickness and the possibility to produce mirror image components (left/right hand) in one program. Year - 2007 CE X axis stroke 1100mm. Y axis stroke 250mm. Max. depth of cut 120mm (depending on chisel size) Rodpjymnbnsfx Al Ist Z axis stroke 100mm Max. workpiece height of 120mm. All movements on re-circulating ball and screw drive with brushless motor Max. workpiece width 200mm Max. swing chisel thickness 20mm. Min . slot length 25mm approx (with swing chisel) Min. slot thickness 6mm. 3 vertical pneumatic clamps. 3 horizontal pneumatic clamps. 4 hp main motor. 'Power 1000' touch screen graphic controller with 99 programs each with 50 lines. USB key facility. Programmable speed for cutting depth. Anti splinter guards with air blowers and dust extraction points. Working table dimensions 1210mm x 215mm Air supply 6 bar / 470 l/min consumption. Fitted with separate dedicated programmable hollow chisel head for producing the small mortises for glazing bars

Condition: good (used), Year of construction: 2012, functionality: fully functional, power: 18.5 kW (25.15 HP), input voltage: 400 V, input current: 37 A, input frequency: 50 Hz, type of input current: three-phase, pressing force: 175 t, stroke length: 265 mm, operating speed: 10 mm/s, reverse speed: 100 mm/s, table width: 104 mm, table length: 3,700 mm, table height: 900 mm, throat depth: 410 mm, clearance between the columns: 3,100 mm, oil tank capacity: 250 l, total length: 5,300 mm, total width: 2,700 mm, total height: 2,750 mm, overall weight: 13,100 kg, Equipment: CE marking, safety light barrier, 2012 Durma AD-R 37175 CNC Press Brake – 175 Ton x 3700mm | CNC Advantage Control | Tooling Included Used 2012 Durma AD-R 37175 CNC press brake for sale. 175 ton, 3700mm, CNC Advantage control, tooling included. Manufacturer: Durma Model: AD-R 37175 CNC Pressbrake Control: Durma CNC Advantage Control Year: 2012 Capacity: 3.7m x 175T Condition: Good Description 2012 Durma AD-R 37175 CNC Press Brake – a high-performance, precision hydraulic press brake designed for efficient and accurate sheet metal bending. This machine offers excellent value for workshops looking for a reliable 175 Ton CNC press brake with strong capabilities and proven Durma build quality. Manufactured by Durmazlar (Durma), a globally recognised leader in sheet metal machinery, the AD-R series is known for robust construction, ease of use, and excellent performance-to-price ratio. 🔧 Key Features 175 Ton Bending Capacity 3700mm Bending Length Durma CNC Advantage Control (2D Graphic Programming) 3 Axis Machine (Y1, Y2, X – Powered) Manual R-Axis via Backgauge Fingers Motorised Backgauge with Linear Guides & Ball Screw System European Style Clamping System Full Set of Top & Bottom Tooling Included Top Tool Hangers Included (Supplied, not shown in photos ⚙️ Technical Specifications Bending Force: 175 Ton Bending Length: 3700 mm Distance Between Columns: 3100 mm Stroke: 265 mm Daylight: 530 mm Throat Depth: 410 mm Table Width: 104 mm Table Height: 900 mm Speeds Y Rapid Feed: 120 mm/sec Working Speed: 10 mm/sec Return Speed: 100 mm/sec Backgauge X Axis Travel: 650 mm X Axis Speed: 500 mm/sec Backgauge Fingers: 2 (height adjustable) General Motor Power: 18.5 kW Oil Tank Capacity: 250 Litres Dimensions (L x W x H): 5300 x 2700 x 2750 mm Weight: 13,100 kg 💡 Machine Overview The Durma AD-R series is engineered for precision bending, low maintenance costs, and long-term reliability, making it an ideal solution for fabrication shops and industrial production environments. With a large daylight opening, generous stroke, and rigid frame construction, this machine is well suited for handling a wide range of sheet metal applications, from light fabrication to heavy-duty bending work. The CNC Advantage Control system provides: 2D graphical programming Automatic bend sequencing Redpjy Ir D Dofx Al Ist Easy part calculation USB program storage and backup User-friendly interface for fast setup and operation 🏭 Why Buy This Machine? Excellent price-to-performance CNC press brake Strong European build quality Ideal for steel fabrication, sheet metal workshops, engineering firms Complete with tooling – ready to go to work Reliable and simple CNC control – easy for operators 📦 Included with Machine Full Top & Bottom Tooling Set Top Tool Hangers (supplied) Sliding Support Arms Backgauge System Notes: *Specifications are given in good faith but not guaranteed*

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Redpfx Aox Dnb Uol Ist Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see our video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned Rodpfxsx A U Nco Al Ist • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.