Used Berger for sale (285)

Condition: used, Year of construction: 2002, grinding diameter 450 mm grinding length 1500 mm centre height 225 mm Control FAGOR EQUIPEMENT - T1: grinding wheel diameter 500 mm - T2: grinding wheel diameter 400 mm - T6: HF Fischer spindle MFV or MFZ 1224/1242/1260 - T7: HF Fischer spindle MFV or MFZ 1224/1242/1260 - Marposs tool measurement - active longitudinal positioning - Elaso GAP-control on T1 and T2 contactless integrated in the control surface - Elaso GAP internal grinding with fluid sensor for T6 and T7 - semi-automatic balancing by Elaso integrated in the control surface for T1/T2 - tailstock hydraulic with fine adjustment +/- 150 microns - dresser on workpiece spindle side table mounted - dresser on tailstock side table mounted - dresser on upper table - new service- and userfriendly housing SPECIAL EQUPEMENT: Workhead with direct drive - strongly recommended for non-circular grinding - workpiece weight flying max. 75kg - workpiece weight between centres 150kg - water-cooled B-axis with direct drive - center height 225 mm - extremely torsionally stiff - highly accurate positioning - resolution ° - water-cooled Hydrostatic ball screw - x-axis - wear-free, as there is no contact during operation - no loss of precision, even during long-term use at full load and maximum speed - no friction at low speeds - no friction force backlash when the direction of rotation changes - translates even the smallest rotational movements - no stick-slip effect even at low speeds - no fluctuations in frictional torque due to ball circulation - higher axial stiffness compared to ball screws - significant improvement in damping, resulting in better workpiece surface finish and tool life - no oscillations due to ball circulation - also suitable for high speeds and accelerations - cost-effective alternative to the linear motor with greater precision and significantly lower heat generation - significantly less power dissipation and, as a result, no problems with swarf on permanent magnets New hydraulic unit - optimized temperature control (chiller) - Energy-saving Only one pump controlled by VFD - Pressure monitoring - monitoring of the hydrostatic oil for water content. (Damage to the bellows is recognised and detected prematurely) -fine adjustment +/- 150 microns Paper belt filter 375l – alternative 480l Grinding mist extraction system – emulsion MECHANICAL OVERHAUL -complete machine according to Kellenberger protocoll -new painting ELECTRICAL OVERHAUL - new modern Fagor CNC with BEMA HMI - new electric cabinet - new digital drive technology - replacement of all electrical cables, switches etc. - new absolute external scales in x- and z-axis - new absolute encoder (B-axis) Grinding software BEMA-Standard: - workpiece zeroing - grinding wheel zeroing - dressing diamond measuring - corrections - external and internal surface grinding - external and internal angle grinding (turning of the b-axis, dressing with straight wheel) - external and internal radius grinding (radius dressed on wheel) - semi-automatic traverse grinding - workpiece zeroing - 2 dressing diamonds - 1 dressing blade - dressing roll - 3 flat dresser - corrections - Z-position measurement - GAP control Optional grinding cycles at no extra charge: Gjdpfxjuxfu Nj Anljuc Profile plunge grinding: - external and internal profile plunge grinding with profile wheel Pr...

Condition: used, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm dimensions of the machine ca. 3,6/3,5 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your is: Kellenberger Kel-Varia Baureihe mit Kelco 90 Steuerung. Mechanische Überholung: -komplette Maschine nach Kellenberger Messprotokoll überholt -Neue servicefreundliche Kabine -Neulackierung Elektrische Überholung: -Neue moderne CNC-RUNDSCHLEIFMASCHINEN-Steuerung -Neu aufgebauter Schaltschrank -Neue Antriebstechnik -Austausch sämtlicher elektrischer Leitungen Berus Druckschalter etc. -Neue Absolut-Glasmaßstäbe in x- und z -Neuer Absolut Drehgeber (Bei-B-Achse) Standardausstattung: -WSS mit Konus MK5, optional mit Adapter MK5/Kurzkegel -RST mit MK4 Konus. Optional mit Feinverstellung -Schleifspindelstock T1/T2/T3 -T1 Schleifscheibendurchmesser 400mm -T2 Schleifscheibendurchmesser 300mm -T3 Innenschleifeinrichtung riemengetrieben. -Schleifspindelmotor 4,4kW -B-Achse hochauflösend -Marposs Messsystem zur Schleifscheibenvermessung. -Längspositionierung Marposs -GAP Control (Sensor am Schleifspindelstock) Optionen gegen Aufpreis: -HF Innenschleifspindel -Hochgenauer, höchst kippsteifer Werkstückspindelstock Guodpsuwv H Hsfx Anlec -Messteuerung Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, grinding diameter 250,350,450 mm grinding length 1000 mm centre height 125,175,225 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø Gusdpfx Ansuxftxslsc 0-0,95 mm/Ø ±8 ° longitudinal feed of the table 1300 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,5 t dimensions of the machine ca. 4,2 x 2,0 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your o von Kürzlich gelieferten Maschinen mit zusätzlichen Optionen wie: -Spritzschutztüren -Kabine x-Achse -Schwenkwinkelanzeige Schleifspindelstock Geometrisch überholt und neu lackiert mit original Elektrik. Maschine hat Zentralschmierung und Rollenführung in der Flachbahn der x-Achse sowie Luftabhebung im Schleifspindelstock serienmäßig. -Digitalanzeige in 2 Achsen. Auflösung x-Achse 0,5my Optionen: -Drehgeber mit digitaler Anzeige im Werkstückspindelstock -Drehgeber mit digitaler Anzeige im Schleifspindelstock (keine Höhenverstellung mit Spindel möglich) -Neue stabile Innenschleifvorrichtung Durchmesser 80mm oder 100mm mit Höhenjustierung. -Erhöhung der Spitzenhöhe auf max. 225mm -Drehzahlregelung für die Schleifspindel Inklusive: -Bedienwerkzeug -Spannrohr für Futter weiteres Zubehör auf Anfrage. Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, Year of construction: 1982, grinding diameter 630 mm grinding length 600 mm centre height 320 mm Maschine wird überholt nach Kellenberger Messprotokoll und neu lackiert. Gsdpjvq R Uzofx Anlouc Die anfällige Güttinger Steuerung wird durch die zeitgemäße BEMA X Steuerung ersetzt. Das heißt die Maschine erhält in diesem zuge auch eine komplett neue Elektrik. Siehe Beispielfotos. Maschine mit verstärktem Werkstückspindelstock zum fliegend Schleifen von schweren Werkstücken. Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, grinding diameter 350,450 mm grinding length 600 mm centre height 175,225 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±10 ° longitudinal feed of the table 900 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,2 t dimensions of the machine ca. 3,1 x 2,0 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your machines. Foto von bereits gelieferter Maschine mit eventuell anderen Optionen. Maschine hat Zentralschmierung und Rollenführung in der Flachbahn der x-Achse sowie Luftabhebung im Schleifspindelstock serienmäßig. BEMA Standard serienmäßig: -Digitalanzeige in 2 Achsen. Auflösung x-Achse 0,5my -Drehzahlanzeige Schleifspindel -Stufenlose Drehzahl Schleifspindel 70-100% -Stufenlose Drehzahl Innenschleifspindel 70-100% -Werkstückspindelantrieb durch Drehstrommotor stufenlos regelbar über Frequenzumrichter Mögliche Optionen gegen Aufpreis: -Drehgeber mit digitaler Anzeige im Werkstückspindelstock -Drehgeber mit digitaler Anzeige im Schleifspindelstock (keine Höhenverstellung mit Spindel möglich) Gsdped Ih D Esfx Anljuc -Sinuslineal -Neue stabile Innenschleifvorrichtung Durchmesser 80mm oder 100mm mit Höhenjustierung. -Erhöhung der Spitzenhöhe auf max. 225mm -Drehzahlregelung für die Schleifspindel Inklusive: -Bedienwerkzeug -Spannrohr für Futter Natürlich erhalten Sie auf unsere generalüberhalten Maschinen 12 Monate Gewährleistung. (Nur Anrainerstaaten) weiteres Zubehör auf Anfrage. Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln

Condition: used, grinding diameter 250 mm grinding length 1000 mm centre height 125 mm grinding wheel diameter 500 mm grinding wheel width 80 (100) mm bore 203,2 mm MK5 work piece spindle speed 20-400 U/min workpiece spindle swivable +/- 360 ° grinding head swivellable +/- 0 ° 0-9,99 mm/Ø 0-9,99 mm/Ø table swivelabel +/- 10 ° table speeds 0,02-6 m/min 130 kg max. workpiece weight -without tailstock 130 inkl. Spannung kg cross travel 270 mm tailstock quill taper MT 3 quill travel 30 mm total power requirement 5,5-7,5 kW weight of the machine ca. 2,7 t As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your machines. delivery: completely overhauled including a new control Examples: Gsdpfsd Ih Egox Anljuc Accessoies: - Marposs auto-sizing-attachement - Balancing for the wheel. Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, grinding diameter 350 mm grinding length 1500 mm centre height 175 mm weight of the machine ca. 3 t High-End Kellenberger 1500U Ideal for spindle producer or overhauler -BEMA Internal grinding device with separate, cooled motor. Grinding spindle and internal grinding spindle motor electrically interlocked! Internal grinding spindle can only be switched on when it is in position. A quantum leap in safety -Infinitely variable grinding spindle speed 1000-1500 rpm -Infinitely variable internal grinding spindle speed 0-100%. -Digital display of grinding spindle speeds -Swivelling angle display top table -swivel angle display grinding headstock -Marposs gaper sensor for external grinding only -fluid gating sensor Marposs internal grinding -Center height up to 250mm possible Machine is already delivered. Identical machine can be built with additional with additional options. Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den Gsdpfxot Ii Rre Anljuc grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, Year of construction: 1982, grinding diameter 630 mm grinding length 600 mm centre height 320 mm Godpfx Aov Dxxzonlouc Machine with heavy duty workhead. Machine will be partial overhauled before delivery. Machine will get a geometry protocoll according to the Kellenberger new machine guideline

Condition: used, grinding diameter 250,350,450 mm grinding length 1000 mm centre height 125,175,225 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±8 ° longitudinal feed of the table 1300 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,5 t dimensions of the machine ca. 4,2 x 2,0 m Ready for delivery, with 12 month warranty in germany and neighbouring countries! Geometrically overhauled and repainted with new electrics. In KELLENBERGER quality!!! -Digital display in 2 axes. Resolution x-axis 0.5my -Modern workpiece headstock with cone MK5 -Modern tailstock with cone MK3 -Modern hydraulic unit -Paper belt filter Godpfx Ansv I Eq Sjleuc Further accessories on request

Condition: used, Year of construction: 2010, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm Control Fanuc 310is Completely machanically overhauled with grinding process and setup of one part. Original photo taken on the EMO 2010. CNC control GE Fanuc 310is Hand panel for CNC control GE Fanuc Wenger loader optional Turned part with automatic indexing 1° Grinding head UR 1-2-3 Grinding wheel equipment left 500 x 80 mm Grinding wheel equipment right 400 x 63 mm Operating unit for one high-speed internal grinding spindle MFV / MFZ High-frequency internal grinding spindle MFN 1090 Guodpfx Anovdk N Eslsc Coolant supply through the workpiece spindle Dressing unit on the upper table Swivelling holder for PCD diamond plates Basic module for KEL-TOUCH gate sensor and KEL-BALANCE balancing devices KEL-TOUCH lead sensor for universal grinding head variants R / RS / UR / URS KEL-TOUCH on the workpiece headstock for internal and external grinding Preparations for Movomatic ESZ 400 or Marposs P7 ME measuring controls Preparation for external filters Cooling lubricant switch-off for table devices Full casing emulsion Emulsion sanding mist extraction system Maintenance unit for additional pneumatic functions Preparation for KEL-VITA gantry loader KEL-POS, MOVOMATIC: C25 measuring probe Hydraulic preparation for arobo bezel

Condition: used, Year of construction: 1995, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm Teilüberholte Maschine mit Messprotokoll nach Neumaschinentoleranz NEUE Steuerung Eckelmann ENC mit BEMA Schleifsoftware KEL-ASSIST für Kelco 90 numerisch gesteuerte B-Achse Innnschleifrinrichtung Dia 80mm Schleifscheibe links Durchmesser 400mm Schleifscheibe rechts Durchmesser 300mm Innenschleifspindel HJN 828 hydraulischer Reitstock Guedpfx Ansyatx Seljc Mikroverstellung KEL SET Messsystem

Condition: used, Year of construction: 2002, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm dimensions of the machine ca. 3,6/3,5 m Photos of identical machine with centre height 225mm Base: Kellenberger Kel-Varia UR175-1000 Kelco 120 Grinding head UR with T1-T2-T3 Basic equipment: -T1 500mm grinding disc diameter -T2 400mm grinding wheel diameter -Infinitely variable, high-resolution axis -Marposs measuring device for tool measurement -Active longitudinal positioning -GAP on T1 and T2 from ELASO contactless integrated in the control interface Semi-automatic balancing from ELASO integrated into the control interface -Tailstock with manual retraction -MK5 workpiece headstock with short taper DIN 55026 Belt-driven internal grinding device Options at an extra charge: - New high-precision workhead with torque drive - Internal grinding device for high-frequency spindles diameter 120mm -HF internal grinding spindle Fischer MFM-1224/42/31 D-21 -HF spindle with HSK holder 24,000 rpm with integrated GAP sensor. (delivery time) -CNC-controlled C-axis non-circular grinding -hydrostatic threaded spindle in x -new hydrostatic unit with only 1 pump and pressure accumulator thus better energy efficiency. -monitoring of the water content in the hydrostatic system -Suction system Further options available on request Mechanical overhaul: -Complete machine overhauled according to Kellenberger measurement protocol -New service-friendly cab -repainting Electrical overhaul: -New modern CNC CIRCULAR GRINDING MACHINE control with BEMA rough grinding surface -New control cabinet -New drive technology -Replacement of all electrical cables Berus pressure switches etc. -New absolute glass scales in x and z -New absolute rotary encoder (for B-axis) Control system: The grinding software consists of a basic licence and various options that are possible depending depending on the equipment of the machine. Basic software - External and internal pendulum grinding - External and internal plunge-cut grinding - External and internal pendulum grinding - External and internal plunge-cut grinding - External and internal taper pendulum grinding - External and internal radius grinding, radius dressed on disc - Semi-automatic pendulum grinding - Workpiece zeroing - Grinding wheel zeroing Gedpfx Anouxfucolsuc - Measuring the dressing diamonds - 2 moulding diamonds - 1 shaped diamond or dressing roll (dressing roll required) - Moulding roller (dressing roller required) - 3 Flat dresser - Corrections - Z-position measurement (probe required) - GAP probing (grinding device required) OPTIONS at an extra charge: Software profile plunge-cut grinding: - External and internal profile plunge-cut grinding with profile disc Profile grinding software: - External and internal profile grinding with straight disc Software thread grinding: - Single and multi-start external and internal thread grinding with thread on the disc disc Dressing. Dressing of single and multi-groove discs. Flank angle freely selectable. Trapezoidal thread grinding software: - Additional dressing of trapezoidal threads possible External and internal non-circular plunge-cut grinding: - External and internal non-circular plunge-cut grinding Non-circular grinding software: A prerequisite for non-circular grinding is that the workpiece axis is equipped with a high-resolution rotary encoder so th...

Condition: used, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0-9,99 mm/Ø 0-9,99 mm/Ø ±8 ° longitudinal feed of the table 1100 mm table speeds 0,02-6 m/min 130 kg cross travel max. 270 mm 130 inkl. Spannung kg 80 mm tailstock quill taper MT 3 quill travel 30 mm total power requirement 6,5 kW weight of the machine ca. 3,05 t dimensions of the machine ca. 4 x 2 m Overhauled according to Kellenberger guidelines including new, modern and future-proof control system. Photo of already delivered machine in centre distance 1000mm. -Operation via the touch panel is extremely simple. -The symbols on the control panel are practically identical to the original original control system, so there is no need for familiarisation. -Diagnostic function with display of PLC messages and digital I/O -Dressing function can be extended or changed at the customer's request. -Orientated spindle stop of the workpiece spindle possible on request. -New maximum infeed of 40 mm can be extended on request. -Digital display in 2 axes. Resolution x-axis 0.5my Options: -Encoder with digital display in the workpiece headstock -Rotary encoder with digital display in the grinding headstock (no height adjustment with spindle possible) with spindle possible) -New stable internal grinding device diameter 80mm or 100mm with height adjustment. -Increase of the centre height to max. 225mm -Speed control for the grinding spindle Included: -Operating tool -Clamping tube for chuck Further accessories on request. The x-axis of the machine has an electronically controlled infeed system with stepper motor drive. Hydraulic longitudinal and rapid traverse table movement. Versatile application in production for external cylindrical and internal internal grinding or for external, face and internal grinding in one clamping clamping of individual parts. Possible options: -Semi-automatic dressing cycles for external and internal grinding -automatic dressing compensation. Guodjuxfupepfx Anlec -Measuring control

Condition: used, Year of construction: 2006, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm weight of the machine ca. 3,5 t Machine completely overhauled with 12 months warranty Mechanically and optically like new Photos from the last overhauled machine with different options Fanuc 21i control Guedpfx Aet Ii Nbenljc -Grinding head UR 1-2-3 external/internal/plan -Axis automatic 1° Hirth serration -Active longitudinal positioning KEL-POS Movomatic -Semi-automatic balancing device KEL-BALANCE -Grinding wheel equipment left 400mm diameter -Grinding wheel equipment right 300mm diameter -Internal grinding unit with belt drive -Tailstock with micro-adjustment -fine adjustment upper table -Paper belt filter SBP4 240l

Condition: used, grinding diameter 250,350,450 mm grinding length 1000 mm centre height 125,175,225 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±8 ° longitudinal feed of the table 1300 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,5 t dimensions of the machine ca. 4,2 x 2,0 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your machines. Gsdpfst Ii Nujx Anlouc Geometrically overhauled with new paint and original electrics. Foto of a 600U which we already have delivered. -Digital display in 2 axes. Resolution of x-Achse 0,5my Options: -Encoder with digital display in workpiece spindle head -Encoder with digital display in grinding spindle head (Height adjustment with spindle not possible) -New stable internal grinding diameter 80mm oder 100mm with height-adjustment. -Increase the center heigh to max. 225mm -Speed control of the grinding spindle Including:: -Adjustment tool -Draw tube for chucks other accessories on reqeust Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, grinding diameter 350 mm grinding length 1500 mm centre height 175 mm Grinding wheel left 500mm diameter Grinding wheel head fix. No swivelling possible. With new control. With new enclosure Overhauled according to Kellenberger protocoll Guodpfxot Ii Rfo Anloc

Condition: good (used), Lohberger Food Serving Unit Dimensions: Width: 2100 mm Depth: 850 mm Height: 800 mm Guedpfx Ansxqx Rgslec Height with glass shelf: 1170 mm Depth with tablet shelf: 1180 mm Basins: W x L x D 300 x 510 x 200 mm Water supply via water connection on the basins Find more items - new and used - in our shop! International shipping costs upon request!

Condition: good (used), Year of construction: 1992, functionality: fully functional, machine/vehicle number: 1522, type of input current: three-phase, input voltage: 400 V, grinding wheel diameter: 225 mm, rotational speed (min.): 1,500 rpm, overall weight: 850 kg, space requirement height: 1,400 mm, space requirement length: 1,230 mm, space requirement width: 850 mm, grinding wheel width: 50 mm, clamping range: 85 mm, year of last overhaul: 2024, • Grinding range 13 - 85 mm / Point angle 80° - 160° • Overhauled 6-jaw special chuck in 03-2024 (€ 6,250) • Including operating tools • Water tank on wheels (60 liters) • Extension sleeves • Halogen lamp 230V Gedpfoxyhl Ssx Anleuc Includes operating manual, exploration drawing, wiring diagram, assembly and spare parts list. Supply of spare parts and maintenance continues to be guaranteed by a specialist company!

Condition: used, functionality: fully functional, For sale is a universal cylindrical grinding machine from the Strausser-kellenberger brand Technical data: Guodpfx Anev E Ivfeljc Manufacturer: Strausak AG Maschinenfabrik (Switzerland) Model: 57U Voltage: 380V / 50 Hz Machine purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For further information or contact options, visit us on our website

Condition: used, Year of construction: 1992, Used machine Year of manufacture: 1992 Features and technical specifications: Electro-hydraulic frame press control Pressing force up to 1,200 kg Two movable longitudinal pressure beams mounted with double ball bearings and guide rails These rails allow for continuous height adjustment of the cylinders The press cylinders can be adjusted via quick-release pressure lever with automatic locking Two electro-hydraulic control valves (with 3 switching stages) operated by hand levers This allows for precise pressing and assembly of even the most complex frame constructions Working height x working length: 2,000 x 3,000 mm Equipped with 3 vertical pressure cylinders Godpfowwxywjx Anlsuc Equipped with 2 horizontal pressure cylinders Stroke of pressure cylinders: 120 mm Three-phase motor: 1.3 kW Pressure control unit / pressing force adjustable: 0 - 60 bar Space requirement: 3,950 x 900 x 2,550 mm Weight: approx. 620 kg Availability: short-term Location: Flörsheim

Condition: new, Year of construction: 2026, control type: CNC control, KBA - Combined CNC-controlled press brake / guillotine shear Super-compact machine with a very small footprint. Maximum cutting length: 3,020 mm or 2,020 mm Rated cutting capacity: 6 mm steel sheet / ST 40 Cutting angle: 1°30″ Guodpjy Afxqefx Anloc Backgauge for the shear station – adjustment range: 750 mm Table height: 750 mm Maximum bending length between side frames: 3,550 mm or 2,505 mm Maximum pressing force: 1,000 kN Working height for bending: only 1,230 mm Stroke range (bending station): 175 mm Maximum installation height (bending station): 350 mm Backgauge adjustment range (bending station): 750 mm Dimensions including operator’s pendant: 4.25 or 3.25 m x 1.82 m x H 2.8 m Required floor space: 3.85 or 2.85 x 1.82 m Drive power: 10 kW Weight: 9,000 kg or 7,500 kg Equipment: - CNC control with touchscreen and 10” colour display, graphical user interface, and automatic bending angle calculation - 1 set of press brake tools (bending punch + four-way reversible die) - Sheet metal supports for the press brake station - 90° angle stop for the guillotine shear with 1 m length - Bending station working area safeguarding via light barriers, rear area safeguarded by lateral safety guards and light barriers Optional: - Front bending area guarding by PILZ® camera monitoring - Rotatable angle stop

Condition: new, Year of construction: 2026, Brand new precision vertical slotting machine – a machine of exceptionally high quality. Guedpfx Ansy Afu Sjlsc CNC-controlled vertical slotting machine with two, three (or four) CNC axes and electronic rotary table control with a positioning accuracy of 0.001°. Ideal for the efficient production of keyways (including tapered and tangential slots), spline hubs, internal and external gears, racks, etc. CNC control with 10" color display and touchscreen – software for roughing, finishing, and fine finishing (enabling surfaces of the highest possible quality). Stroke range of slotting ram: 10 to 250 mm Slotting ram speeds: 22 to 90 strokes/min, infinitely adjustable Slotting ram swivel range: +/- 20° Rotary table diameter: 450 mm Rotary table bore Ø: 135 mm Maximum table load: 1,250 kg Table travel (X/Y): 250 x 225 mm Ram drive servomotor power: 3 kW Machine dimensions without control console: 1.3 x 1.45 m x approx. height 2.6 m Machine weight approx. 1,700 kg - Automatic electronically monitored central lubrication system for the guideways - Cutting oil system for coolant supply to the slotting tools Other models available.

Condition: new, Year of construction: 2026, OSTERBERGER KSBP 2500 Universal Brand new combined universal long-belt sander - brushing machine - polishing machine in portal construction. Sanding length and width can be customized according to customer requirements, also available with two sanding belts in parallel for two workstations, allowing for pre-sanding and finishing without changing the belt, as well as a brush and polishing head with automatic longitudinal adjustment to the left and right. The machine is suitable for coarse and fine sanding, structuring (brushing), polishing, and high-gloss polishing of a wide variety of surfaces including painted workpieces, natural workpieces, and various metal sheets made of stainless steel, aluminum, brass, copper, bronze, and various plastics. Combined long-belt sanding machine with brushing and polishing unit for workpieces up to 650 mm in height: Guodoy Afu Espfx Anljc - Motorized movement of the brushing and polishing unit from left to right and back - Manual movement of the support table forwards and backwards - Motorized adjustment of the support table up and down Worktable size: 2,500 x 1,000 mm (other sizes available upon request) Sanding belt dimensions: 8,200 mm x 150 mm Drive power of brushing and polishing unit: 3 kW Drive power of sanding belt unit: 3 kW Dimensions approx. 4,200 x 1,600 x H 2,100 mm Weight approx. 1,000 kg

Condition: new, Year of construction: 2026, Welding Fume Extraction Arm for Wall Mounting with Extraction Blower – self-supporting structure with rotary joints Pipe diameter: 150 mm Length: 8,200 mm (extension 4,000 mm + arm 4,200 mm) Complete with radial fan 1.5 kW / 2,800 rpm Extraction capacity: 1,450 m³/h Extraction velocity: 0.55 m/s Weight: approx. 163 kg The SKAW extraction arm consists of an extraction hood connected by an aluminum pipe with a self-supporting structure. The articulation uses stabilization friction joints that allow for precise positioning. 360° rotational movement is ensured by a fifth rotary bearing, made of a material specifically developed to avoid hardening over time through use. The hood is equipped with a handle and a damper for regulation or shut-off. This combination guarantees a perfect blend of technology and design. Gujdpfx Asy Afufsnlsc

Condition: new, Year of construction: 2026, Heavy-duty manual universal precision sheet metal folding machine (swing bending machine) in very robust cast-iron construction – brand new Maximum bending length: 3,050 mm Gujdpfx Ajy Afgzenloc Maximum sheet thickness: - Steel – Precision sheet DC01-A with tensile strength approx. 350N/mm² – 2 mm - Aluminium sheet H24 with tensile strength approx. 145N/mm² – 3 mm - Zinc sheet according to DIN EN988 with tensile strength approx. 190N/mm² – 2.5 mm Upper beam – opening range 250 mm – - Allows box bending up to 250 mm. - Optionally available with motor-driven upper beam actuation. Maximum bending angle: 135° Lower beam adjustment range: 90 mm Bending beam adjustment range: 90 mm - An ideal machine for the production of pipes, pipe segments, and radius parts Dimensions without rear gauge approx. 3.6 m x 570 mm x height 1.3 m Weight: 3,000 kg