Used Cutting Shear for sale (14,289)

Condition: used, LVD Shear Type HST C-10/31 Capacity 3000 x 10 Hsdpex Tqtbjfx Addeng

Condition: good (used), Year of construction: 2014, CUTTING MILL TYPE PALLMANN PS-H 1000 x 1400, 132 kW Hnsdpfx Adjx Szkuodjg very good condition with 3 sets of rotor and stator knives with 2 sets of screens, 5 and 8 mm AVAILABLE AND READY TO WORK

Condition: used, Year of construction: 2024, Flat bed laser 3000mm x 1500mm. 1.5 kw Raycus laser source. Hnsdpfx Adox N Ic Ssdjg Possible upgrade to 3kw. 1mm - 14mm capacity.

Condition: used, Year of construction: 1982, sheet width - max. 1255 mm plate thickness 4.0 mm ST plate thickness 2.0 mm VA plate thickness 6.0 mm ALU number of strokes - loaded ~ 66 Hübe/min. cutting angle 1.5 ° back stop - adjustable max. ~ 1.000 mm total power requirement 5.5 kW weight of the machine ca. 2600 kg. range L-W-H 1750 x 1800 x 1800 mm Machine from a technical college - prototype construction very well-maintained condition (!!) Furnishing: - electro-hydraulic guillotine shears - manual backgauge with analogue position display (scale + magnifying glass) - electrical cutting length limitation - manual cutting gap adjustment - 1x extra long side stop Hsdpsxaa I Sofx Addong - 2x extra long support arms - 1x free moving footswitch - rear sheet metal slide - User manual (PDF) * Machine link : ?machineno=1008-9325278

Condition: used, Hydraulic Plate Shear LVD Type HST-C 31 / 6 Machine No. 21348 Year of manufacture: 1994 Cutting length: 3,100 mm Cutting thickness: 6.35 mm Backgauge: 770 mm Working height: 950 mm Hydraulic sheet hold-downs: 17 units Hydraulic tank capacity: 150 liters Motor power: 7.5 kW Power connection: 400 Volt, 50 Hz, 9.5 kW, 19 Amp. - Motorized backgauge with digital actual position display ELGO - Backgauge adjustment via push button – rapid in both directions and fine adjustment by jogging in the minus direction only Hodetvb Iuspfx Addeng - Sheet lifting device below the backgauge with pneumatic lifting cylinder - Continuously adjustable blade gap from 0.1 mm via handwheel with analog display - Cutting angle adjustment in 5 steps from 1.5° to 3.5°, electrically pre-selectable - Left side angle stop 1,500 mm - 2 table extensions as sheet supports - Electric foot switch - Comprehensive operating manual Space requirements without front table extension (L x W x H): 4,150 x 1,850 x 1,900 mm Space requirements with front table extension (L x W x H): 4,150 x 2,850 x 1,900 mm Weight: 5.5 tons Good condition Very good cutting results, including with thin sheet metal

Condition: good (used), Tapping chuck, thread chuck, tapping chuck, thread cutting attachment -Manufacturer: Fahrion, thread cutting attachment GA 30 -Shaft: MK3 -Reversing gear: integrated quick return, slip clutch -Clamping diameter: max 23 mm Hnjdpfx Aswvfyuoddsg -Dimensions: 230/125/H80 mm -Weight: 6.3 kg

Condition: good (used), Year of construction: 2014, CUTTING MILL TYPE PALLMANN PS-H 1000 x 1400, 132 kW very good condition with 3 sets of rotor and stator knives with 2 sets of screens, 5 and 8 mm Hnjdpex Szfrefx Addjg with electrical cabinet AVAILABLE AND READY TO WORK

Condition: good (used), Year of construction: 1991, sheet width - max. 1010 mm plate thickness 4.0 mm ST plate thickness 2.5 mm VA plate thickness 6.0 mm ALU number of strokes - loaded max. 20 Hübe/min cutting angle 1.5 ° work height max. 900 mm Control ELGO Hnsdpfx Aoxrgv Tsddsg back stop - adjustable max. ~ 1.000 mm total power requirement 5.5 kW weight of the machine ca. 2200 kg. range L-W-H 1500 x 2155 x 1606 mm from a maintenance workshop good condition (!!) - in checked conditions - machinevideo - ?v=w22S17mfU-A Equipment: - Robust NC electro-hydraulic guillotine shear - NC electro-motorized backgauge * Includes NC ELGO positioning control "TYP 85" - Electric cutting length limiter - Manual cutting gap adjustment - 1x side stop with scale - 2x support arms - 1x freely movable foot switch - Original operating instructions * Special accessories included: - Pneumatic holding device for thin sheet metal blanks

Condition: good (used), Thread cutting chuck, thread chuck, tap chuck, milling tool, thread cutting apparatus -Tapping chuck: MK3 mount -Type: PH3/3 -Square: 7 x 7 mm -Bore: Ø 9 mm -Dimensions: Ø 80 x 225 mm Hnodpfjrp Ikgsx Addsg -Weight: 3.0 kg

Condition: excellent (used), operating hours: 1,500 h, - rotary shear type MEWA UC 201 - Electric drive 2 x 75 kW - Rotor length approx. 2 meter - width of the knives 70 mm Hnjdpfx Adex Szflsdsg - with chain conveyor for the outlet of the product It is a very powerful machine for shredding materials as tires or light scrap.

Condition: ready for operation (used), punching pressure 45.0 t punch diameter 22 in 15.0 mm punch diameter 38 in 8.0 mm round bar steel 30.0 mm square edge steel 25.0 L-beam 100 x 10.0 mm shear: flat material 300 x 12.0 mm adjustment of stroke 0 - 55 mm work height max. 940 / 1140 mm strokes per minute 34 punch diameter max. 110 mm voltage 400 V Hodpfxexaat Uo Addjng total power requirement 4.5 kW weight 1245 kg dimensions 1520 x 590 x 1700 mm In good condition (!!) New price ~ 13.000 Euro Special price upon request Features: - Robust electro-hydraulic profile steel shear - With multiple workstations: * Punching station * Flat steel shear * Angle/profile steel shear * Notching station - Continuously adjustable stroke - Very compact design - Support table at the notching and punching station - Side support surfaces - 1x freely movable foot switch - Central lubrication system - Connection cable + connector

Condition: good (used), Thread cutting chuck, thread chuck, tap chuck, milling tool, thread cutting apparatus -Manufacturer: WMW, tapping chuck holder MK2 -Type: A2 MK2 -Bore: Ø 12 mm Hsdperv Au Rofx Addsng -Dimensions: Ø 70 x 267 mm -Weight: 3.3 kg

Condition: ready for operation (used), Year of construction: 1997, sheet width 3230 mm plate thickness 2.5 mm thickness at "Niro-steel" 1.5 mm no. of strokes 28 - 42 Hub/min cutting angle 1.60 Grad table height 820 mm distance between columns 3540 mm Control ELGO 87P engine output 6.8 kW weight of the machine ca. 3410 kg. range L-W-H 4070 x 2070 x 1400 mm from a maintenance workshop including special accessories (!!) Equipment: - robust / motorized swing cut guillotine shears - break-proof, torsion-free steel welded construction - compact and clear machine design - NC electro-motorized back stop - including NC ELGO "TYP 87P" digital control unit * adjustable from the front right * with target/actual value position input * continuous adjustment over the entire travel range * rough adjustment via push buttons * protection of the limit values ??with limit switch - "Duo-Cut" drive with two dynamic, powerful gear motors - support table with recessed grips - hold-down bar with hard rubber strip Hnodpsxacd Nsfx Addjg - all-steel knife with two cutting edges - selector switch for single and continuous stroke - 1x freely movable foot switch - safety device at the rear - original operating instructions Special accessories included: - pneumatic sheet holding device for thin sheet metal cuts - 1x extra long side stop, including support foot + digital stop - 2x extra long, front support arms * with "SLIDING" mount - for easy moving

Condition: good (used), Die set, hand pipe thread cutter, thread cutting machine, pipe thread cutter, pipe thread cutter, cutting head Hnodpfx Adec T Nx Iodsg -for pipe size: max. 2" inch -5x Cutting tips: 3/4" 1" 1 1/4" 1 1/2" 2" inch -2x Threaded ratchets: Type 111-R/12-R -Price/Sale: complete -Weight: 12.8 kg

Condition: good (used), Modular aggregate unit, format processing unit, machining unit, milling unit, form milling unit, jointing milling unit, end-cutting unit, double-end tenoner, edge processing machine, scoring motor, chipper motor, milling motor for edge processing machine -HOMAG cutting unit for cutting off edge protrusions on the front and rear edges -with heavy leadership -Milling unit: swiveling -1x Perske motors -Engine Type: -Power: 0.75 kW Hnsdob Sc Svjpfx Addjg -Voltage: Volts -Frequency: 300 Hz -Speed: 8,600 rpm -Other engines with different performance levels are available from us for an additional charge. -Dimensions: 990/620/H340 mm -Weight: 52 kg

Condition: good (used), Thread cutting machine, pipe thread cutter, thread cutting head, thread cutting chuck, thread chuck, thread cutting apparatus -Manufacturer: Rems, thread cutting head -Pipe size: 2 1/2 to 4 inches -Spindle bore: dimensions see pictures -Dimensions: 410/400/H340 mm Hnodpfswq Nviox Addog -Weight: 50 kg

Condition: good (used), Window rubber, cutting machine, seal cutter, pneumatic slat cutter, cutting device, pneumatic cutting device, pneumatic press Hsdpetpyqqjfx Addeng -Manufacturer: Benzing, pneumatic cutting device -Stroke: adjustable, max. 70 mm -Individual components: see photos -Dimensions: 150/130/H450 mm -Weight: 9.3 kg

Condition: good (used), Flame cutting system, torch, oxyfuel cutting system, machine cutting torch, flame cutting machine, cutting torch, cutting machine, oxyfuel cutting machine, gas cutting torch Hodpfexy Hlwox Addsng -Manufacturer: Messer Griesheim, machine cutting torch, flame cutting machine -Type: Quicky Electronic -Cutting speed: adjustable -Voltage: 220 V 40 W -Dimensions: 580/280/H370 mm -Weight: 7.8 kg

Condition: good (used), Modular aggregate unit, format processing unit, machining unit, milling unit, form milling unit, jointing milling unit, end-cutting unit, double-end tenoner, edge processing machine, scoring motor, chipper motor, milling motor for edge processing machine -HOMAG cutting unit for cutting off edge protrusions on the front and rear edges -with heavy leadership -Milling unit: swiveling -1x Perske motors -Engine Type: Hnodpfxsb Sgzae Addsg -Power: 0.75 kW -Voltage: Volts -Frequency: 300 Hz -Speed: 8,600 rpm -Other engines with different performance levels are available from us for an additional charge. -Dimensions: 940/620/H350 mm -Weight: 54 kg

Condition: used, Tobacco cutting machine -Sold/handed over: in its current condition as seen -Prototype: Machine is not operational -Manufacturer: Sagemüller, tobacco cutting machine with knife sharpening device Hjdpfeiy Efisx Addjng -Cutting blades: 8 pcs. length 400 mm, 2 pcs. die 850/120/H275 mm -Individual components: see photos -Machine dimensions: 1900/1340/H1810 mm Total weight: 1935 kg

Year of construction: 1999, condition: good (used), Cutting device, pneumatic press, punch Hedpfxsb A Ncze Addjng -Type: 290 908 -Max. pressure: 8 bar -Dimensions: 300/340/H270 mm -Weight: 25 kg

Condition: good (used), Modular aggregate unit, format processing unit, machining unit, milling unit, form milling unit, jointing milling unit, end-cutting unit, double-end tenoner, edge processing machine, scoring motor, chipper motor, milling motor for edge processing machine -Manufacturer: Homag, cutting units from edgebanding machine BRANDT KM 36 -Engines: Homag type LF-40-L / Perske KNS 22.08-2 -Power: 0.27 kW / 12000 rpm / 10800 rpm -Voltage: 220 V / 200 Hz Hnedpfjgy Da Sex Addog -Pneumatic components: Bosch -Individual components: see photos -Price/Sale: complete -Overall dimensions: 500/560/H670 mm -Weight: 51 kg

Condition: good (used), Plasma cutting machine, plasma cutter for plasma cutting system Hodpjwpg I Tjfx Addong -Manufacturer: Hypertherm, gas console for plasma cutting machine -Type: 073239 from plasma cutting machine HT2000LHF -Dimensions: 295/175/H370 mm -Weight: 9.9 kg

Condition: good (used), Cable shears -Cable shears: hydraulic -without: hydraulic unit -Max. Opening: 95 mm -Number: 1x cable shears available -Dimensions: 530/180/H80 mm Hjdpfx Ajd R Ew Rsddong -Weight: 13.3 kg

Condition: good (used), Flame cutting pliers, electrode pliers, hose assembly Hnsdpfx Adeb A S Avsdeg -Length: 3 m Price: per piece -Quantity: 5 available -Weight: 3.5 kg/piece