Used Die Bending Machine for sale (67,724)

Condition: used, Swing bending machine with additional segmented upper tool, gooseneck rail. Swing bending press brake FASTI type 2095-25-2.5, serial no. 94 295 004, year of manufacture 1994. Working length 2540 mm, max. sheet thickness 2.5 mm, upper beam stroke 380 mm, bending beam motor power 2.2 kW, power supply 400 Volt, 50 Hz. - NC control FASTImatic FM100 - one-piece sharp rail 135° - additional segmented upper tool, gooseneck rail - controlled backgauge - continuous stop rail - controlled bending angle via control - electric foot switches. Weight 3000 kg. In good condition. Fgedpfx Ajttc Uasggeg

Condition: new, pressure 100 kN stroke 0-200 mm table-size 450 x 1000 mm Fsdpfx Ajzr Rp Djggogg working speed: 6-10 mm/ sec. return speed 20 mm/sec work height max. 900 mm toolpiece height max. 200 mm total power requirement 1,5 kW bending capacity max. - round 42x3,2 mm 150x10 mm weight 320 kg dimensions 1010x480x1120 mm

Condition: used, Max. bending length: 1020 mm Fgjdpfx Ajzl Dngoggeg Max. sheet thickness: 6 mm steel Upper wheel diameter: 150 mm Motorized rear roller delivery Right and left rotation via foot switch Safety rope pull switch Conical rounding possible Weight: 1200 kg

Condition: excellent (used), Year of construction: 2007, Technical data: Working length: 2550 mm Max. bending capacity for small diameters: 12.0 mm Bending capacity from diameter 900 mm: 18 mm Bending allowance: 10 / 12.0 mm Roller diameter: 310 mm Hydraulic folding bearing Drive power: 11 kW Lateral bending support Sheet metal holding device Digital display Dimensions (length x width x height): approx. 4200 x 1500 x 1650 mm Weight: approx. 10 tons Condition: Fsdpfoztckisx Aggogg Overall in very good condition, used only sparingly. The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear are consistent with its age; used machines are sold without any warranty.

Condition: ready for operation (used), One Gietz platen die-cutting and embossing press and one Polygraph free-arm wire stitching machine are offered. 1) One Gietz Presto platen printing, die-cutting and embossing machine, max. paper size X/Y: approx. 320mm/480mm, frame size X/Y: approx. 320mm/460mm, working area X/Y: approx. 350mm/480mm, max. paper size without additional equipment: approx. 330mm/470mm, capacity: approx. 2500strokes/h, flywheel revolutions per stroke: 8, flywheel diameter: approx. 725mm, flywheel width: approx. 50mm, working height: approx. 900mm, weight: approx. 1100kg. Inspection possible by prior arrangement. 2) Polygraph 781/1L50 RF free-arm wire stitching machine, year of manufacture: 1960, number of stitching heads: 1, max. stitching thickness: approx. 8mm, stitching arm length: approx. 500mm, front stitching arm width: approx. 10mm, inside staple crown length: approx. 12mm, max. stitching capacity: approx. 250stitches/min. Inspection possible by prior arrangement. Fgedpfxozk Nb As Aggsg

Condition: ready for operation (used), Year of construction: 2017, Performance range: 20mm-60mm, max. bending angle: 180°+10°, max. bending radius: 150mm, effective length: 3048mm, bending height: 1050mm, max. section modulus: 12.1cm³, bending tolerance: +/-0.1°, operating pressure: 200bar, connected load: 4kW, machine dimensions X/Y/Z: approx. 2000mm/900mm/1200mm, weight: approx. 500kg. Documentation available. On-site inspection is possible. Fjdewg E Dhspfx Aggogg

Year of construction: 1997, condition: ready for operation (used), Wire diameter (single wire): 6mm-14mm, wire diameter (double wire): 6mm-10mm, maximum bending angle: 180°, motor power: 22kW, feed rate: 1.5m/s, bending speed: 1000°/s, cutting time: 0.4s, hydraulic tank volume: 300l. Machine dimensions X/Y/Z: approx. 4900mm/1640mm/2200mm, weight: approx. 3300kg. Control system defective. Documentation available. On-site inspection is possible. Fgjdpjuwrv Defx Aggjg

Year of construction: 2000, condition: ready for operation (used), A hydraulic 4-roll plate rolling machine Promau (Prümau) is available. Working width: 3000mm, bending capacity: 13mm, pre-bending capacity: 10mm, rolls: 4. An on-site inspection is possible. Fjdpfx Aszhw Tueggogg

Year of construction: 2007, condition: ready for operation (used), A Wafios CNC wire and tube bending center is available. Axes: 9, wire diameter range: 1.5mm-8mm, tube diameter range: 3mm-10mm, wire tools: 2.5mm/4mm/5mm, tube tools: 6×1mm, feed speed: 120m/min, feed roller pairs: 3, bending head transverse stroke min./max.: -200mm/200mm, bending head stroke min./max.: -120mm/25mm, bending head orientation: 0°/30°, return length range: 400mm-1300mm, bending moment: 520Nm, upsetting force: 10kN. Machine dimensions X/Y/Z: approx. 3500mm/1800mm/2300mm, weight: approx. 5800kg. Documentation available. An on-site inspection is possible. Fgjdpfjzka Nwsx Aggsg

Condition: ready for operation (used), A CNC flat wire vertical wire bending machine V&C GmbH is available. Wire thickness range: 0.8mm-10mm, max. wire width: 30mm, min. winding inner diameter: 20mm, max. winding outer diameter: 250mm, max. winding height: 160mm, max. winding height with holding rod: 500mm, max. winding length: 250mm, min. bending radius: R6°, max. number of edges: 12/revolution. Machine dimensions X/Y/Z: approx. 2650mm/1000mm/1800mm, weight: approx. 800kg. Documentation available. On-site inspection is possible. Fodpfsycwtfex Aggegg

Year of construction: 2017, condition: ready for operation (used), An asymmetrical three-roll plate bending machine MG is available. Working width: 2000mm, roller diameter: 130mm, max. plate thickness: 3mm, power: 6kW, weight: approx. 2000kg. An on-site inspection is possible. Fjdpfjyttwbjx Aggjgg

Year of construction: 1997, condition: ready for operation (used), Travel X/Y/Z: 500mm/350mm/500mm, table dimensions X/Y: 800mm/600mm, max. table load: 800kg, work bowl dimensions X/Y/Z: 860mm/620mm/350mm, max. electrode weight: 200kg, tool positions: 28, machine dimensions X/Y/Z: approx. 3000mm/3750mm/3000mm, weight: approx. 3340kg. Documentation available. On-site inspection is possible. Fgjdpfx Agjvc Ha Regjg

Condition: ready for operation (used), An automated tube bending system with two Wafios bending heads and a Kuka twister robot is available. 1) Bending head Wafios RB20, bending direction: left and right, max. total tool height: 78mm, bending capacity: 360Nm, bending speed: 560°/s, bending radius: 57mm, repeat accuracy bending, turning and feed: +/-0.05mm. 2) Robot Kuka KR 16-2 KRC 2, axes: 6, payload: 16kg, max. reach: 1611mm, repeat accuracy: +/-0.05mm, weight: approx. 235kg. Including suspended magazine, Kuka control cabinet, outfeed conveyor, safety fence, movable control panel, docking station and work table. Documentation available. On-site inspection is possible. Fgedpfowwlkisx Aggog

Year of construction: 1978, condition: ready for operation (used), A Haeusler CNC large-format 4-roll plate bending machine is available. Number of rolls: 4, Roll width: 3050mm, Max. prebending plate width: 3000mm, Max. prebending plate thickness: 60mm, Max. rolling capacity at max. plate width and 3500mm bending diameter: 70mm, Roll diameter top/bottom/side: 620mm/600mm/500mm, Max. top roll load: 12000kN, Operating speed: 4m/min, Connected load: 132kW, Weight: approx. 85t. Including cone bending device. Documentation available. An on-site inspection is possible. Fjdpozka H Aefx Aggsgg

Year of construction: 1991, condition: ready for operation (used), Travel X/Y/Z: 380mm/280mm/300mm, working dimensions X/Y/Z: 580mm/450mm/340mm, max. electrode weight: 50kg. Machine dimensions X/Y/Z: approx. 2100mm/1650mm/1750mm, weight: approx. 3500kg. An on-site inspection is possible. Fedpfxjzb Nlwo Aggegg

Condition: ready for operation (used), Year of construction: 1996, Clamping force: 3150kN, opening force: 10,000daN, closing stroke: 500mm, ejector force/retraction force: 159/82kN, ejector stroke: 120mm, mould height: 300-700mm, platen dimensions: 900x900mm, tie bar spacing: 550x550mm, tie bar diameter: 110mm, injection position: mm, max. injection force: 350kN, injection stroke: 430mm, injection plunger diameter: 50/60/70/80mm, shot volume: 563/811/1103/1441cm³, specific injection pressure: 1783/1238/909/696daN/cm², corresponding projected area: 177/254/347/453cm², max. projected area: 1050cm² at 300daN/cm², operating pressure: 140bar, dry cycle time (DIN 24480): 500, drive motor: 22kW, control: Datacontrol, length: 6900mm, width: 2000mm, height: 2800mm, weight: 14t, operating hours: 77,185h, shot count: at least 1,147,108, however not guaranteed due to a hardware replacement, adjustable opening stroke, with Striko Westofen W455 holding furnace, ABB IRB 2400 (M96/F10) industrial robot, and documentation. An on-site inspection is possible. Fgedpsza E Rmsfx Aggog

Year of construction: 1987, condition: ready for operation (used), A three-roll plate bending machine Kramer is available. Working width: 2000mm, max. plate thickness: 3mm, power: 3kW. An on-site inspection is possible. Fgodpfx Ageyttv Rogsg

Year of construction: 2005, condition: ready for operation (used), Max. bending diameter: 30mm, an inspection is possible. Fedsrc Hiispfx Aggsgg

Condition: ready for operation (used), Year of construction: 1999, Tube diameter: 25mm, wall thickness: 2mm, bending angle: 190°, feed length: 2000mm, weight: 2t, left-bending. Accessories: CNC IsoBend 2.0. Without mandrel bending device, monitor glass has impact damage but is still functional. An on-site inspection is possible. Fjdpsxcx Atofx Aggjgg

Condition: ready for operation (used), A mandrel tube bending machine Sommer is available. Tube diameter range: 15mm-65mm, tube feed length: 3000mm, max. bending radius: 150mm, chuck: 200mm, tube clamping: hydraulic. Including accessories. Documentation available. An on-site inspection is possible. Fgedpexl Up Usfx Aggog

Condition: used, Year of construction: 1996, functionality: fully functional, machine/vehicle number: 14151, overall weight: 3,485 kg, working width: 3,100 mm, sheet thickness (max.): 2 mm, We are offering this used Göteneds K25-30 A 1200 bending machine, manufactured in 1996. Model: K25-30 A 1200 Working area: 3100mm x 2.0 mm Manufacturing number: 14151 Fodpfxjzdzxgj Aggsgg Year of manufacture: 12/96 Weight: 3485 kg The machine received a new gearbox and a new display some time ago. The machine is in good used condition and has some minor inaccuracies due to its age. However, it is perfectly adequate for many applications. If you have any questions or require further information, please send us a message or call us.

Condition: good (used), Year of construction: 1996, machine/vehicle number: 5090, Offer 22186 Fedpfx Agjztvgwsgogg Technical data: - Bending capacity - Pipe at 45 kg/mm²: Ø 6 - 48 mm - Solid material up to approximately: 30 mm - Max. bending angle: 180° - Bending radius: 2 x D - Drive: 400 V / 1.5 kW - Space requirement: approx. W 4500 x H 1400 x D 1000 mm - Weight: approx. 600 kg - with: - Digital bending angle display + fine adjustment of the bending angle - Mandrel bending device, 3.0 m, with hydraulic retraction - Bending tools: 20 R 60; 22 R 66; 25 R 75 mm - 25 R 50; 38 R 114 mm - Various bending mandrels, length: 3000 mm

Year of construction: 2025, condition: new, Die-cutting machine ML-1200 NXL Brand new machine. This is the strongest die cutter in this format. Format: 1230 × 850 mm Weight: 5500 kg 380 V power supply Engine: 5.5 kW Equipment: – electromagnetic clutch and brake – quick assembly frame Fgodpfezwpxnjx Aggjg – 3 operating modes: continuous, time delayed, manual – central lubrication – additional safety covers – operating tools and instructions with CE documentation. The machine is available „on the spot” We provide a 12-month warranty. Our machines, as few on the market, are adapted to the current regulations in Europe. Possibility of testing in the showroom in Radom.

Condition: excellent (used), functionality: fully functional, Year of construction: 2016, machine/vehicle number: AR200 tube and profile roll, control type: NC control, degree of automation: semi-automatic, actuation type: hydraulic, controller manufacturer: Delsy, controller model: MG Touch Pro 15", pipe diameter (max.): 273 mm, tube wall thickness (max.): 20 mm, bending angle (max.): 200 °, number of axes: 9, working height: 2,200 mm, overall weight: 27,000 kg, total length: 2,850 mm, total width: 2,950 mm, total height: 2,930 mm, power: 29.42 kW (40.00 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, operating pressure: 240 bar, number of digital displays: 6, Equipment: documentation/manual, emergency stop, Profile bending machine model AR200 brand MG srl year 2016 Fgedpfx Asyx A Uuoggjg Capacity chart of the machine in enclosed. Model AR200 Pipe bending roll NR. 2 set of rollers for pipe bending SIZE 159MM - SIZE 139,7 MM Configuration -pyramid dual pinch side rolls independent hydraulic -3 rolls driven hydraulic with gear unit each shaft -side arms left/right side hydraulic move in 3 direction keeping aligned the profile being formed. -Control panel console NC programmable with automatic rolling, touch screen 15” , display the 9 axis of the machine with readout for manual use and fully programmable automatic forming -Electric power supply 3phase 400/50 Vac -40HP -Service manuals and operation books original. Additional set of rollers and tooling available for bending section HEB - IPE -UNP - ANGLE – T -SECTION- TUBULAR- IRON BAR ON EDGE - see capacity chart in enclosed ..

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2021, machine/vehicle number: 20210330-2, control type: CNC control, pipe diameter (max.): 63 mm, pipe length (max.): 2,600 mm, bending angle (max.): 190 °, bending radius (max.): 350 mm, bending radius (min.): 25 mm, overall weight: 3,000 kg, total length: 5,000 mm, total width: 1,200 mm, total height: 1,350 mm, CNC 63CNC AUTOMATIC MANDREL BENDING MACHINE – FOR TUBES AND PROFILES For sale: CNC 63CNC automatic mandrel bending machine, designed for precise bending of tubes and profiles. The machine is equipped with CNC/PLC control with a touchscreen and the ability to save bending programs. TECHNICAL DATA: -Maximum diameter / material dimension: Ø63 × 4 mm -Bending radius: 25–350 mm -Bending angle range: 0–190° Fgjdszy Rgxjpfx Aggjg -Effective length on the mandrel: 2600 mm -Motor power: 7.5 kW -Maximum pressure: 160 kg/cm² -Machine dimensions: 5000 × 1200 × 1350 mm -Weight: approx. 3000 kg EQUIPMENT AND FUNCTIONS: -PLC control with touchscreen -Automatic and manual mode -Diagnostic system -Full hydraulic clamping -Up to 100 programs, each with up to 20 bending operations -Independently programmable speeds of axes Y, B, and C -Programmable material springback compensation -Automatic release of the tube before final bending -Cycle start via foot pedal -Air cooling The machine enables repeatable, precise bending and is designed for production applications where efficiency and process repeatability are essential. Transportation is the buyer's responsibility.