Used Elmag for sale (66)

Condition: used, Year of construction: 2008, machine/vehicle number: 7281, - Producer Elmag Superfici - Type Magnum 3.2.2 - Year of construction 2008 (2010) - Working width 1.350 mm - Working height 900 mm + - 20 mm - Operating side, right - Actual condition, machine is not overhauled - Duo gun drive system - Spraying gun carrier independently controllable Klodpfotz Dgzex Addsl - Dry filter system - Exhaust air 13.500 m³/h - Transport belttransport System - Feed speed adjustable bis 18 m/min - 2 belt cleaning units - Belt cleaning system with roller - Belt cleaning system, behind the machine - Lacquer reclaiming system with v-belt - Gun control system - PLC control with touch screen - Number of installed lacquer circles 2 Stk. - Supply air box - Length ~ 6.680 mm - Width 4.455 mm - Total connection power ~ 26.3 KW - Voltage / HZ 400 / 50 - Location, not on stock - Voltage fluctuation max. +/- 5 %

Condition: used, Year of construction: 1997, machine/vehicle number: 4406, 3D UV dryer Superfici Elmag 2 tubes - 3D UV-dryer Superfici & conveyer Klodpfx Adstz Dg Usdsl - the pictures show the machine before overhaul - Producer Superfici - Type TU166-30 + 2 UVM55 - Year of construction 1997 - Working width 1300 mm - Number of lamp from top 2 Stk. - Lamp bevel to conveyor - For mercury lamps - For gallium lamps - Electic capacity lamp 80 W/cm - Selective shiftable 80/40 W/cm - Feed speed infinitely adjustable by hand wheel ~ 2 - 7,5 m/min - Location - Voltage / HZ 400 / 50 - Commodity code 8419 3200

Year of construction: 1997, condition: used, machine/vehicle number: 4353, Technical data: - Manufacturer: Elmag Superfici - Length: 6.000 mm Klsdjv Tc T Uspfx Addel - Belt width: 1.300 mm - Total width: 1.540 mm - Year of manufacture: 1997 - Feed adjustable via handwheel - Feed speed approx. 2-7.5 m/min. - Frequency converter required on site - Location: in storage - Volt, Hz 400 / 50 - Motor power 0.75 kW

Condition: used, Year of construction: 2001, machine/vehicle number: 5358, - Manufacturer Elmag Superfici - Type. TWIN SPRAY - Year of manufacture 2001 - Working width 1,300 mm - Working height 890 mm + - 20 mm - Operating side right - Price for overhauled machine - Gun drive in duo version - Dry extraction - Exhaust air output 8,000 m³/h - Belt transport system - Belt cleaning via roller cleaning system - With belt cleaning system - Belt cleaning, behind the machine, in the direction of travel, - With paint recovery - Gun control - Number of installed spray guns 4 pcs. - Spray guns type. Kremlin ATX - Airmix spray system - Supply air filter ceiling - Length 5,950 mm - Width 3,980 mm - Height 2,790 mm - Total connection 21 KW, 40 A Kledpfsumvk Aox Addel - Volt, Hz 400 / 50 - Location, in stock _____ Optionally, we can also provide you with a quotation for the assembly and start-up of the system, as well as training for your employees. We also offer regular maintenance and servicing of the machine on request. For further information, get in contact with us!

Condition: new, bore capacity in steel (diameter) 16 mm throat 150 mm bore stroke 90 mm turning speeds 340 - 2200 U/min 243 x 243 mm total power requirement 0,5 kW / Volt weight of the machine ca. 42 Kg dimensions 400 x 450 x 900 mm Table drill - Digital speed display - Spindle protection - vice - drill replacement - Quick span feed (1 to 16 mm) Kodpevdld Rofx Addjll - Tilt and rotating rider work table. - deep stop - tool set - documentation

Condition: new, turning diameter over bed 250 mm turning diameter over slide rest 145 mm Kjdpfx Ajkxhqnsddsll turning length 550 mm turning speeds 50 - 2000 U/min centre height 125 mm spindle bore 26 mm tailstock quill taper MT 2 MK connected load frequency 230 V total power requirement 0,75 kW weight of the machine ca. 0,12 t dimensions of the machine ca. 1,3 x 0,65 x 0,6 m longitudinal feed. 3-jaw chuck 125 mm. 4-way steel holder. chip tray, bulkhead Hardened bed tracks. Emergency stop switch. lining protection Tool box, instruction manual.

Condition: new, turning diameter over bed 250 mm turning diameter over slide rest 145 mm turning length 550 mm turning speeds 50 - 2000 U/min centre height 125 mm spindle bore 26 mm tailstock quill taper MT 2 MK Ksdevdld Dspfx Addsll connected load frequency 230 V bore capacity in steel 16 mm throat 169 mm quill stroke 50 mm turning speed range - drilling 50 - 2250 U/min spindle drive 0,5 kW total power requirement 0,75 kW weight of the machine ca. 0,175 t dimensions of the machine ca. 1,3 x 0,65 x 1,3 m 3-axis LCD digital display system longitudinal feed. 3-jaw chuck 125 mm. 4-way steel holder. chip tray, bulkhead Hardened bed tracks. Emergency stop switch. lining protection Tool box, instruction manual.

Condition: new, Year of construction: 2024, turning diameter over bed 250 mm turning diameter over slide rest 145 mm turning length 550 mm center height over bed 125 mm centre distance 550 mm bed width 135 mm spindle bore 26 mm Kjdpfx Aowlvk Asddjll turning speed range - stepless 50 - 2.000 U/min power requirement 750 W 3-jaw-chuck diameter 125 mm taper in tailstock-quill MK 2 dia. of quill 30 mm quill stroke 70 mm voltage 230 V weight of the machine ca. 120 kg dimensions of the machine ca. 1,25 x 0,60 x 0,50 m

Condition: new, Year of construction: 2024, bore capacity in steel (diameter) 35 mm throat 320 mm bore stroke 150 mm spindle taper MT 4 table-size 500 x 400 mm spindle turning speed range 75 - 3.010 U/min feed range - boring 0,1 / 0,15 / 0,22 / 0,33 mm/U quill stroke 150 mm Klodpfxewlvlas Addol voltage 400 V total power requirement 1,8 kW weight of the machine ca. 275 kg dimensions of the machine ca. 0,70 x 1,00 x 1,95 m - Serial-No.: 138050673 - Electromagnetic feed - Threading device - Machine vice 150 mm - Two clamping screws 14 mm - 9-piece drill cartridge 14.5 mm - 30 mm, MK 2 / MK 3 - Cutting oil spray

Condition: new, Year of construction: 2024, bore capacity in steel (diameter) 32 mm throat 245 mm bore stroke 135 mm spindle taper MT 3 table-size 410 x 380 mm spindle turning speed range 10 - 2.100 U/min voltage 400 V total power requirement 1,1 kW weight of the machine ca. 210 kg dimensions of the machine ca. 0,7 x 1,8 x 1,75 m - Threading device - Machine vice 150 mm - Drill cassette 9-piece 14.5 mm - 30 mm, MK 2 / MK 3 Kledpfxjwlvk Nj Addsl - Cutting oil spray

Condition: new, ELMAG gearbox milling and drilling machine MFB 20 Vario MFB 20 / MFB 20-L / MFB 30 / MFB 30-L Vario With the compact MFB 20 Vario and MFB 20-L Vario milling and drilling machines, precise workpiece machining is a pleasure in any position thanks to a swiveling machine head. The MFB 20 Vario was specially developed for small milling and drilling jobs. With a drilling capacity in steel of 20 mm and a face milling capacity of 63 mm, you can cover a wide range of sizes commonly used in model making and mechanical engineering. Digital displays for speed and drilling depth and infinitely variable speed control provide optimum support. Standard equipment - Quick-action drill chuck B16, 1 - 16 mm - Tapered arbor MK 2 / B 16, thread M10 - Tightening spindle M10 - Tool set - Operating instructions / CE ADVANTAGES Face milling - End milling - Drilling Stepless speed adjustment Digital speed display Emergency stop button Clockwise and counter-clockwise rotation Speed controller Kledpfx Adet Ed Erodsl Precision micro feed Digital drilling depth display Quill fixing Operating lever with fixation Milling spindle with precision bearing Pull-in spindle for high safety Smooth-running, precise cross table with T-slots and coolant channel Milling spindle protection cover Drilling depth scale Zero-tension release Machine stand optionally available TECHNICAL DATA Drilling capacity in steel 20 mm Tapping capacity M14 Milling capacity face milling cutter 63 mm Milling capacity end mill 16 mm Spindle holder (turning spindle) MK 2 Speed range 1 50 - 1125 rpm Speed range 2 100 - 2250 rpm Infinitely variable speed steps Quill stroke 50 mm T-slots, width 12 mm Milling head stroke 375 mm Spindle projection 184 mm Milling head swivel range ± 90 ° Quill distance table 0 - 375 mm Milling table surface 500x180 mm Table travel X x Y 280 x 175 mm Motor power 600 W Mains connection 230/50 V/Hz Cubature 500x180x375 mm Length x width 745 x 570 mm Height 935 mm Weight 103 kg

Condition: new, ELMAG universal milling machine model UFM 125 Unique '2 in 1' concept The swivel head of the UFM 125 can be adjusted to almost any angle and, in addition to normal face and end milling work, enables the machining of fitting surfaces and grooves in difficult spatial positions. For face milling large workpiece surfaces, the machine can be converted into a horizontal milling machine in just a few simple steps (horizontal spindle on the swivel head). Thanks to the high drive power of 2,200 watts, the machine is suitable for face milling cutter diameters of up to 125 mm. The machine is equipped with an automatic cross table feed for the X and Y axes and rapid traverse for the Z axis for rapid table positioning. 11 speed levels and 9 feed levels provide sufficient scope for optimizing the cutting speed. Central lubrication of the guideways for rapid availability and a coolant system with tank in the machine base are very advantageous. The UFM 125 is ideal for single and small batch processing. Standard equipment Digital position display Collet set 4, 5, 6, 8, 10, 12, 14 and 16 mm with collet chuck Tool set Operating instructions / CE ADVANTAGES Automatic feed X/Y/Z Milling capacity Ø 125/40 mm Cubature 1,120 x 260 x 500 mm Spindle projection 60-500 mm Table travel 600x300 mm Tilting milling head ±180° Easy conversion to horizontal milling machine Drive motor 2,200 W Wide speed range Clockwise and counter-clockwise rotation Milling spindles with precision bearings Tightening spindles for high safety Milling spindle protection cover Kedpjt Ef Eysfx Addell Smooth-running, precise cross table with T-slots and coolant channel X- and Y-axis cross table with 9 feed steps Cross table Z-axis with drive Central lubrication Integrated coolant system with return, tank in the machine base LED milling table lighting With digital position display TECHNICAL DATA Milling capacity face milling cutter 125 mm Milling capacity end mill 40 mm Cubature 1120x260x500 mm Spindle holder (turning spindle) ISO 40 Vertical speed range 45 - 1660 rpm Vertical speed steps 11 Horizontal speed range 45 - 1660 rpm Coolant pump 90 W Horizontal speed stages 11 T-slots / width x distance 5 / 14 x 50 mm Spindle projection 60 - 500 mm Milling head swivel range ± 180 ° Quill distance table 80 - 500 mm Horizontal spindle distance table 40 - 470 mm Milling table stroke 420 mm Milling table surface 1120 x 260 mm Table travel X x Y 600 x 300 mm Feed rates X/Y 24 - 402 mm/min Feed steps X/Y 9 Feed Z 1200 mm/min Motor power 2200 W Feed drive X/Y 550 W Feed drive Z 750 W Mains connection 400/50 V/Hz Length x width 1655 x 1325 mm Height 1730 mm Weight 1480 kg

Condition: new, ELMAG universal lathe PREMIUM CU 325 RD - Vario center distance 1000mm incl. RÖHM lathe chuck Kodpfxet Hg Sko Addjll Performance data and holders: - Turning Ø 325-1,320 mm, without bridge 440-1,500 mm - Turning size via slide Ø 190-940 x 6,000 mm - Drive motor: 2,200-22,000 W, 400 V, high torque - Lathe chuck holder: DIN 55027 - Quill holder: MK 3 - MK 6 Standard equipment: - RÖHM three-jaw lathe chuck Ø 160 mm - Quick-change steel holder set, 5-piece - Halogen machine lamp - Emergency stop button / zero voltage release - Lathe chuck guard with safety switch - Tool slide with splash guard - Underframe / chip tray / splash guard - Tool set / operating instructions / CE Standards PREMIUM CU series: - Heavy gray cast iron machine bed, good vibration damping - Dismountable bridge - Prismatic guides - Hardened and precision-ground turning spindle, high concentricity, adjustable precision bearings - Smooth-running rotary spindle and feed gear with oil bath - Gear wheels made of chrome-nickel steel, hardened and precision-ground - Feed reversal circuit - Covered trapezoidal thread lead screw, hardened, precision ground - Tool slide with lock nut - Precise slide guides, adjustable - Solid tailstock with taper turning adjustment - Lathe accuracy according to DIN Special accessories: - SINO digital position indicator for 3 axes - Insert turning tool set 16 x 16 mm, 7-piece - 7-piece insert set, 16 x 16 mm - Grooving tool set incl. plates, 6-piece - Machine shoe Ø 160 mm, 8 pcs. on request: - Steady rest - Steady rest - Steady rest with ball bearing guide - Faceplate - 4-jaw faceplate chuck ADVANTAGES Rotary spindle and feed gearbox with quick-change elements Feed reversal Sliding protective cover Gear plate Halogen lamp Coolant pump Emergency stop button Rapid traverse motor Longitudinal slide TECHNICAL DATA Center width 1000 mm Center height 165 mm Turning diameter over bed 325 mm Turning diameter over carriage 190 mm Turning diameter without bridge 440 mm Machine bed width 200 mm Cross slide travel 150 mm Top slide travel 95 mm Turning tool cross-section, max. 16x16 mm Lathe chuck holder (DIN 55027) no. 5 Spindle holder (turning spindle) MK 4 mm Spindle bore 32 mm Speed range 1, infinitely variable 85 - 405 rpm Speed range 2, infinitely variable 470 - 2200 rpm Longitudinal feeds (48) 0.006 - 1.77 mm/rev Transverse feeds (48) 0.003 - 0.885 mm/rev Metric thread dimension (48) 0.1 - 28 mm metric modular thread (19) 0.1 - 1.75 mm Inch thread, threads G (53) 75 - 2.5 G/' Inch modular thread, threads G (19) 70 - 4 G/' Quill holder MK 3 Quill diameter 40 mm Quill travel 100 mm Motor power 2200 W Mains connection 400/50 V/Hz Length (total) 2150 mm Height (total) 1300 mm Weight 770 kg

Condition: new, ELMAG universal lathe PREMIUM CU 630 RD - Vario center distance 1000mm incl. RÖHM lathe chuck Performance data and holders: - Turning Ø 325-1,320 mm, without bridge 440-1,500 mm - Turning size via slide Ø 190-940 x 6,000 mm - Drive motor: 2,200-22,000 W, 400 V, high torque - Lathe chuck holder: DIN 55027 - Quill holder: MK 3 - MK 6 Standard equipment: - RÖHM three-jaw lathe chuck - Quick-change steel holder set, 5-piece - Halogen machine lamp - Emergency stop button / zero voltage release - Chuck guard with safety switch - Tool slide with splash guard - Underframe / chip tray / splash guard - Tool set / operating instructions / CE Standards PREMIUM CU series: - Heavy gray cast iron machine bed, good vibration damping - Dismountable bridge - Prismatic guides - Hardened and precision-ground turning spindle, high concentricity, adjustable precision bearings - Smooth-running rotary spindle and feed gear with oil bath - Gear wheels made of chrome-nickel steel, hardened and precision-ground - Feed reversal circuit - Covered trapezoidal thread lead screw, hardened, precision ground - Tool slide with lock nut - Precise slide guides, adjustable - Solid tailstock with taper turning adjustment - Lathe accuracy according to DIN Special accessories: - SINO digital position indicator for 3 axes - Insert turning tool set 25 x 25 mm, 7-piece - 7-piece insert set, 25 x 25 mm - Grooving tool set incl. plates, 6 pieces - Machine shoe Ø 160 mm, 6 pcs. on request: - Steady rest - Steady rest - Steady rest with ball bearing guide - Faceplate - 4-jaw faceplate chuck ADVANTAGES Rotary spindle and feed gearbox with quick-change elements Feed reversal Sliding protective cover Gear plate Halogen lamp Coolant pump Emergency stop button Rapid traverse motor Longitudinal slide TECHNICAL DATA Center width 2000 mm Center height 315 mm Turning diameter over bed 630 mm Turning diameter over carriage 430 mm Turning diameter without bridge 830 mm Machine bed width 400 mm Cross slide travel 315 mm Top slide travel 130 mm Turning tool cross-section, max. 32x32 mm Lathe chuck holder (DIN 55027) no. 11 Spindle holder (turning spindle) 120 mm Klodpfx Aot Hhbyoddjl Spindle bore 103 mm Speed range 1, infinitely variable 16 - 63 rpm Speed range 2, infinitely variable 63 - 250 rpm Speed range 3, infinitely variable 315 - 1250 rpm Longitudinal feeds (120) 0.04 - 12 mm/rev Transverse feeds (120) 0.02 - 6 mm/rev Metric thread dimension (64) 0.5 - 120 mm Metric modular thread (64) 0.125 - 30 mm Inch thread, threads G (64) 60 - 1/4 G/' Inch modular thread, threads G (64) 240 - 1 G/' Quill holder MK 5 Quill diameter 90 mm Quill stroke 230 mm Motor power 11000 W Mains connection 400/50 V/Hz Length (total) 3600 mm Height (total) 1400 mm Weight 3310 kg

Condition: new, ELMAG PREMIUM WASTE OIL PWO 65 waste oil collector PREMIUM WASTE OIL waste oil collector Kledpfx Aot Hvywsddel Waste oil collector with 65 or 90 liter tank for quick oil changes ADVANTAGES Generously dimensioned collecting tray, height-adjustable and swivel-mounted Inspection tube for checking the quantity Splash guard insert for convenient storage of oil filters incl. removable tool tray TECHNICAL DATA Tank capacity 65 l Max. Collecting capacity 52 l Collection tray capacity 15 l Enlarged hopper diameter 580 Ø mm Drain hose length 2 m Dimensions LxWxH 600x420x1270-1780 mm Max. Drain pressure 0.5 bar Weight 33 kg

Condition: new, ELMAG SEB 7500WD-AVR power generator with HONDA GX390 engine and AVR control BASIC - gasoline - open design - 400/230 Volt Demanding use? Inductive power consumers? - No problem for the powerful SEB power generators, because that's exactly what they are designed for. They turn chippers, compressors, circular saws, cooling units, mixers, pumps and can also be used for engines that are difficult to start. They supply alpine huts, construction sites and are often used in commercial, agricultural and municipal operations. They are the most commonly used devices for emergency power. SEB WD models are available in outputs from 7 to 24 kVA, thus covering a wide range of outputs for a variety of consumers. SEB 7500WD-AVR Frequently requested 400/230 volt frame device for commercial use a, construction, for service work and agriculture as well as for private emergency power supply. With AVR control for sensitive loads and high unbalanced load capacity thanks to oversized generator. Features - Connections: 1x 230 V Schuko 16 A and 1x 400 V CEE 16A-5p - Manual start - Shutdown: low oil and overload - Synchronous generator - AVR control - Protection class IP 23 ADVANTAGES Original Honda four-stroke air-cooled gasoline engine AVR control for sensitive consumers as standard With Honda EasyStart manual start system or, depending on model, with electric start system and maintenance-free starter battery Thermal circuit breaker with overload cut-out Automatic switch-off in the event of low oil pressure or low oil pressure TECHNICAL DATA Voltage - frequency 400 / 230/50 V/Hz Maximum power 3~400V 8 kVA Continuous power 3~400V 7.2 kVA Power 3~400V cont. 10 A Maximum power 1~230V 3.8 kVA Continuous power 1~230V 3.4 kVA Power 1~230V cont. 14.4 A Kodpfst H Hw Tjx Addoll Fuel type Petrol Speed 3000 rpm Cooling air-cooled Engine type Honda GX 390 Exhaust stage 5 Engine power 8.2 kW Displacement 389 cm³ Cylinder 1 Fuel tank capacity 6.1 l Consumption at 75% load 2.8 l/h Running time per tank filling at 75% load 2.2 h Dimensions LxWxH 830x510x560 mm Weight (without fuel) 91 kg Sound power according to RL 2000/14/EG, 2005/88/EG 97 LWA Sound pressure level at 7m 72 dB(A)

Condition: new, ELMAG SEBSS 12000WDE-AVR-DSE3110 power generator with HONDA GX630 engine, electric start and AVR control (super-silenced) SUPERSILTENT - petrol - super-silenced - 400/230 volt The super-silenced SEBSS models are technically perfect and elegant. At just 62 dB(A), they are among the quietest petrol-powered generators. They supply alpine huts, building sites, stages and tents, sales stands and weekend homes, are used as mobile emergency helpers by the fire department and protect important private, commercial, agricultural and municipal facilities as emergency power generators. SEBSS generators are equipped with 230V Schuko sockets or CEE connections. WDE models also have a 400V CEE connection. Equipment - Connections: 1x 230 V Schuko 16A, 1x 230 V CEE 16A-3p and 1x 400 V CEE 16 A-5p - Starter: electric choke, electric start, battery - Shutdown: low oil, overtemperature, overload and short circuit - Synchronous generator - AVR control - Protection class IP23 - DSE 3110 - Voltmeter - Hour meter - Remote start connection - Interchangeable tank - Diaphragm pump - Sound insulation, SS Popular optional equipment (option) - Trickle charger - A-LTS Automatic load transfer switch Kljdpst H Ibtefx Addel - 4-wheel set ADVANTAGES Quality drive - original Honda four-stroke air-cooled petrol engine Synchronous generator with electrical voltage regulation - AVR, ideal for sensitive consumers Thermal-magnetic circuit breaker with shutdown in the event of overload and short circuit Automatic switch-off in the event of overtemperature and low oil level NEW: Now with DSE 3110 control module for automatic engine & generator monitoring and remote start/stop via potential-free contact TECHNICAL DATA Voltage - frequency 400 / 230/50 V/Hz Maximum power 3~400V 12 kVA Continuous power 3~400V 10 kVA Power 3~400V cont. 14.4 A Maximum power 1~230V 4 kVA Continuous power 1~230V 3.7 kVA Power 1~230V cont. 16 A Fuel type Petrol Speed 3000 rpm Cooling air-cooled Engine type Honda GX 630 Exhaust stage 5 Engine power 14 kW Displacement 688 cm³ Cylinder 2 Tank capacity 20 l Consumption at 75% load 4.2 l/h Running time per tank filling at 75% load 4.8 h Dimensions LxWxH 1270x750x590 mm Weight (without fuel) 204 kg Sound power according to RL 2000/14/EG, 2005/88/EG 91 LWA Sound pressure level at 7m 66 dB(A)

Condition: new, ELMAG Stone cutting machine (incl. slide) STM 900/350 K, 230 Volt With or without miter table K Quality machines up to 110 mm cutting depth, ideal for natural stone and gardening companies, pavers and stonemasons. Easily movable, lockable cutting unit with handy handle, Protective cladding with cooling water connections and splash guard Professional stone cutter With the STM models, ELMAG offers professionals a wide selection of flexible, high-quality stone cutters. In addition to the usual 'normal cut', these tried and tested machines also master heavy granite floor slabs and complex mitre cuts on steps or concrete and stoneware mouldings. The tried and tested details and working aids of these particularly robust, fully galvanized stone cutting machines meet the expectations of a modern, reliable machine with a long service life. All models are available with or without a mitre table and are optionally available with a 230 V AC or 400 V AC drive motor. available. ADVANTAGES Disc cooling with dosing valve Corrosion protection: fully galvanized design Pull-out water tray With infinitely adjustable mitre table 0 - 45° Very powerful drive motor Klodpfx Adet Hvmksdjl Safety switch with zero-voltage release Easy transportation on plastic castors, four carrying handles TECHNICAL DATA Cutting capacity depth/length 110 / 900 mm Angle 0 - 45 ° Diamond cutting blade Ø 350 mm Diamond blade bore 25.4 mm Rated power 2.2 kW Voltage/frequency 230/50 V/Hz Dimensions 1350x780x1300 mm Weight 97 kg

Condition: new, ELMAG Motorized folding machine model MSS-SH 2020x4,0mm Compact production solution The ergonomically designed folding machines combine the advantages of manual and motorized devices. In the UNIM series, the workpiece is clamped by an eccentric lever; in all MSS, MSL and MSS plus models, it is motorized by the lifting spindle arranged on the side. An additional electric motor is used to bend the sheet metal, resulting in an optimum, cost-effective solution. Kljdpfx Aet Egdqsddjl The folding machines can be equipped with a manual or motorized backgauge, which considerably simplifies the work for the operator. The machines are equipped with a foot control for easy alignment work on thin sheets. These models are suitable for one-off production and are many times more efficient than manual machines. They can also be used in all industrial operations. Standard equipment model MSS - Manual angle adjustment - Foot pedal with emergency/stop function - Manual bending beam adjustment (material thickness) - Operating instructions / CE TECHNICAL DATA Bending length 2020 mm Material thickness 400 N/mm² 4 mm Material thickness 600 N/mm² 2.5 mm Material thickness aluminum 275 N/mm² 6 mm Opening 90 mm Motor power bending beam 4 kW Clamping motor power 1.1 kW Length 3120 mm Width 1150 mm Height 1660 mm Weight 3900 kg

Condition: new, ELMAG STBS-500 masonry band saw STBS for dry cutting (bricks, aerated concrete, insulating material) The STBS series masonry band saws are specially designed for use designed for use on construction sites. In dry cutting, they are suitable for the precise processing of materials such as aerated concrete, bricks, lightweight poroton, expanded clay and wood, but also for insulation boards such as Styrofoam and Styrodur. ADVANTAGES Connection piece for dust extraction available Saw blade tension easily and optimally adjustable with handwheel Includes forklift pockets and lifting eye Constant saw blade tension and 440 mm running wheels for reduced risk of blade breakage and precise cuts Direct drive with geared motor on extra motor console Automatic saw blade switch-off at the end of the cut Machine stops when the doors are opened Short saw blade change times Straight, miter and manual contour cuts possible Precise band guide, adjustable to the block height Kljdpfx Aot Egfzjddol Easy relocation thanks to transport wheels and transport bar TECHNICAL DATA Cutting height 500 mm Cutting length 660 mm Angle 0 - 45 ° Saw blade dimensions 3850x27 mm Table size 710x1060 mm Rated power 1.85 kW Mains connection 230/50 V/Hz Dimensions 1050x900x1840 mm Weight 203 kg

Condition: new, ELMAG reversible vibratory plate RPD24-50 with Hatz- Diesel 1B20, 24 kN centrifugal force, with steel protective frame Ksdpfxjt Egvgo Addell Vibratory plates, reversible With stepless hydraulic switching between forward and reverse as standard. This allows large areas to be compacted with powerful machines. Vibratory plates with very high compaction performance in a wide range of versions to suit customer requirements. On all models, the machine is protected against damage by a high-quality steel protective frame. Incl. transport hook. Special accessories - Rubber mat incl. holder - Wheel set ADVANTAGES Infinitely hydraulically adjustable forward and reverse travel Self-tensioning clutch system for reduced V-belt wear Crack and break-resistant base plate made of hardened steel Guide bar can be locked in vertical position during transport or storage New protective cage offers reliable protection for the motor and the device Extra strong rubber bearings installed Easy to mount transport wheels TECHNICAL DATA Centrifugal force 24 kN Max. Speed 20 m/min Area compaction 600 m²/h Motor type 1B20 Power 3.3 kW Plate size 500x680 mm Working width 500 mm Vibration frequency 92 Hz Weight 164 kg

Condition: new, ELMAG universal lathe PREMIUM CU 400 RD - Vario center distance 1000mm incl. RÖHM lathe chuck Performance data and holders: - Turning Ø 325-1,320 mm, without bridge 440-1,500 mm - Turning size via slide Ø 190-940 x 6,000 mm - Drive motor: 2,200-22,000 W, 400 V, high torque - Lathe chuck holder: DIN 55027 - Quill holder: MK 3 - MK 6 Standard equipment: - RÖHM three-jaw lathe chuck - Quick-change steel holder set, 5-piece - Halogen machine lamp - Emergency stop button / zero voltage release - Chuck guard with safety switch - Tool slide with splash guard - Base frame / chip tray / splash guard - Tool set / operating instructions / CE Standards PREMIUM CU series: - Heavy gray cast iron machine bed, good vibration damping - Dismountable bridge - Prismatic guides - Hardened and precision-ground turning spindle, high concentricity, adjustable precision bearings - Smooth-running rotary spindle and feed gear with oil bath - Gear wheels made of chrome-nickel steel, hardened and precision-ground - Feed reversal circuit - Covered trapezoidal thread lead screw, hardened, precision ground - Tool slide with lock nut - Precise slide guides, adjustable - Solid tailstock with taper turning adjustment - Lathe accuracy according to DIN Special accessories: - SINO digital position indicator for 3 axes - Insert turning tool set 25 x 25 mm, 7-piece Klsdpfet Hhbtex Addel - 7-piece insert set, 25 x 25 mm - Grooving tool set incl. plates, 6-piece - Machine shoe Ø 160 mm, 8 pcs. on request: - Steady rest - Steady rest - Steady rest with ball bearing guide - Faceplate - 4-jaw faceplate chuck ADVANTAGES Rotary spindle and feed gearbox with quick-change elements Feed reversal Sliding protective cover Gear plate Halogen lamp Coolant pump Emergency stop button Rapid traverse motor Longitudinal slide TECHNICAL DATA Center width 1000 mm Center height 200 mm Turning diameter over bed 400 mm Turning diameter over slide 235 mm Turning diameter without bridge 550 mm Machine bed width 320 mm Cross slide travel 235 mm Top slide travel 110 mm Turning tool cross-section, max. 25x25 mm Lathe chuck holder DIN 55027 No. 6 Spindle holder (turning spindle) MK 6 mm Spindle bore 52 mm Speed range 1, infinitely variable 18 - 98 rpm Speed range 2, infinitely variable 48 - 265 rpm Speed range 3, infinitely variable 3: 144 - 790 / 4: 385 - 2120 rpm Longitudinal feeds (80) 0.015 - 0.6 mm/rev Transverse feeds (80) 0.0075 - 0.3 mm/rev Metric thread dimension (40) 0.25 - 7.5 mm metric modular thread (40) 0.0625 - 1.875 mm Inch thread, threads G (40) 120 - 4 G/' Inch modular thread, threads G (40) 480 - 16 G/' Quill holder MK 4 Quill diameter 50 mm Quill travel 100 mm Motor power 7500 W Mains connection 400/50 V/Hz Length (total) 2350 mm Height (total) 1330 mm Weight 1590 kg

Condition: new, ELMAG drill grinder DBG 832 W 8 - 32mm DBG - 3 in 1 The DBG series drill grinder is used for grinding twist drills made of HSS and carbide twist drills. The machine has integrated grinding stations for grinding the point angle, the clearance angle and for cross grinding. Special CBN or SDC diamond grinding wheels are used, which are to be used depending on the drill material. material. SDC coated grinding wheels Metal-coated synthetic diamond for sharpening carbide drills. CBN coated grinding wheels Deliver sensational sharpening results at very high speed and without annealing. The special thermal conductivity of CBN (boronite crystals) dissipates the resulting frictional heat into the wheel, preventing hardening of the cutting edge and virtually eliminating sparking. CBN has a higher thermal stability than diamond and is ideal for sharpening HSS tools due to lower wear. Optionally available: Grinding wheel SDC for DBG 832 W Order no. No. 61016 Collet chuck holder for Ø 31-32 mm for DBG 832 W Collet set (ER40) 2-piece, Ø 31-32 mm for DBG 832 W Now free of charge with both models Collet holder and collet set ER 20 or ER 40 ADVANTAGES CBN grinding wheel for HSS Adjustment device for center angle 95°-135 Clearance angle grinding function Cross grinding function For drill bits 8-32 mm 23 collets 8-30 mm TECHNICAL DATA Grinding range drill bit Ø 8 - 32 mm Grinding range point angle 95 - 135 ° Klodpfst Hhg Nsx Addol Speed 4400 rpm Motor power 0.25 kW Mains connection 230/50 V/Hz Length 490 mm Width 250 mm Height 260 mm Weight 27 kg

Condition: new, ELMAG metal circular saw MKS 315 RLSS-N- SUPER-SET-ACTION SUPER-SET-ACTION - MKS RLSS-N standard equipment - Universal or sheet steel base - Material stand for circular metal saws - Quality saw blade HSS/DMo5 - Coolant concentrate 1:10, 5 liters Standard equipment - MKS RLSS-N metal circular sawing machine - Material support with roller - Bar stop with material stop - WSS quick angle clamp/angle scale - Adjustable cutting depth stop - DSS double quick-clamping vice - Quick clamping lever - Adjustable clamping jaw(s) Kledpst Hkbpsfx Addsl - High-performance drive - Gearbox with permanent oil bath lubrication - Cooling system with diaphragm pump - ERGO operating lever with reset - Permanent safety switch on the handle - Self-closing saw blade guard - Emergency stop/zero voltage release - Tool/Operating instructions/CE ADVANTAGES High accuracy for series cutting - with bar stop and material stop Quick miter adjustment with a lever handle - with quick angle clamp and 45-0-45° angle scale Flexible miter setting - gear head and/or vice can be swiveled Cutting depth can be precisely limited - with cutting depth stop Powerful - two-speed drive motor 40/80 rpm Smooth-running and durable - quality gearbox with oil bath for permanent lubrication Optimum cooling - coolant circulation system with diaphragm pump, dosing valve and return filter Compact - coolant tank integrated in chip tray Stable cutting guide - with ERGO operating lever Safe - self-closing saw blade guard, permanent switch, emergency stop, zero voltage release, CE-compliant TECHNICAL DATA Round tube cutting range at 0° Max. 90 mm Round tube Cutting range at 45° right mitre Max. 80 mm Square tube Cutting range at 0° Max. 80 mm Square tube Cutting range at 45° right miter Max. 70 mm Rectangular tube Cutting range at 0° Max. 115x70 mm Rectangular tube Cutting range at 45° right mitre Max. 70x70 mm Saw blade outer diameter 315 mm Saw blade inner diameter 32 mm Vice clamping width max. 120 mm Cutting angle 45-0-45 ° Speed level 1 / 2 40 / 80 rpm Motor power speed level 1 / 2 1500 / 2200 W Mains connection 400/50 V/Hz Infeed height for roller conveyors 1030 mm Length 1475 mm Width 1000 mm Height 1150 mm Weight 150 kg

Condition: new, ELMAG LRGM 3050-4mm Mechanical plate shears High quality standards - Robust and durable design - High cutting accuracy - Welded monoblock steel construction with very good vibration damping - Special steel blades can be used on both sides, hardened and precision-ground - Precise backgauge with handwheel and measuring scale, adjustment range 0-750 mm - Parallel guidance of the blades for exact cutting quality - Manual cutting gap adjustment CE safety devices - Installed safety through cutting gap cover - Rear of machine protected by light curtain - Emergency stop button on the machine and on the control column Optimum handling - Support table with ball rollers for effortless sheet positioning - Support arms and side stop - Two operating modes: manual and automatic - Clear LRGM control panel with operating buttons - Mobile operating column with foot release for automatic operation Performance data LRGM Cutting capacity up to 4 mm material thickness Cutting length 3050 mm - Ideally matched to standard sheet formats Cutting speed 41 strokes per minute - Ideal for fast, serial processing Kljdpst Egb Ajfx Addol High drive power 7.5 kW - Sufficient power for continuous use ELGO NC control only for NC models Easy-to-use numerical control for programming the backgauge. of the backgauge. - Quick cutting length input and manual individual operation at the touch of a button - 99 memory locations - Display in millimetres or inches Standard equipment - Special steel blade with two cutting edges - Side stop and support arms - LED illumination of the cutting line - Manually adjustable back gauge - CE safety devices - LRGM control panel and mechanical stroke counter - Mobile control column with foot release and emergency stop button - Operating instructions / CE TECHNICAL DATA Cutting length 3050 mm Cutting capacity 42 kg/mm² 4 mm Number of strokes 41 1/min Drive Motor power 7500 W Backgauge adjustment range 750 mm Length 3700 mm Width 2150 mm Height 1450 mm Weight 4010 kg