Used Frequency Inverter for sale (6,502)

Condition: new, For sale: electric motor from the renowned manufacturer ATB Motorentechnik GmbH, made in Germany. Model CD160M-4, explosion-proof ATEX II 2G version, suitable for inverter operation. Technical data: • Power: 11 kW • Type: CD160M-4 • Voltage: 400 V Δ / 690 V Y • Current: 21 A / 12.1 A • Frequency: 50 Hz • Speed: 1460 min⁻¹ (4-pole) • Cos φ: 0.85 • Insulation class: F • Protection rating: IP55 • Weight: 168 kg • Year of manufacture: 2007 • ATEX: II 2G EEx de IIC T4 – motor for areas with explosive gas hazard • Shaft: diameter 42 mm, splined. Lodpfx Aoxbd U Esnxoag

Condition: new, Year of construction: 2024, functionality: fully functional, machine/vehicle number: iASN075N - 2200xxxxxxx, cooling capacity: 164 kW (222.98 HP), type of input current: three-phase, type of cooling: water, overall weight: 2,634 kg, ambient temperature (max.): 46 °C, ambient temperature (min.): -10 °C, input voltage: 400 V, pressure: 10 bar, temperature: 7 °C, volume flow: 28.9 m³/h, total width: 2,241 mm, total length: 3,541 mm, total height: 2,425 mm, warranty duration: 12 months, input frequency: 50 Hz, Equipment: type plate available, Sales exclusively to customers with a German billing and delivery address! Laedpfx Asxaz Iyonxog Process chiller / chilled water unit, air-cooled, Type: iAries N iASN 075 HE Special – R290 MTA S.p.A. The Aries N iASN 075 HE Special is a compact chilled water unit suitable for outdoor installation. The unit is Eurovent certified. Equipment: - Refrigerant R290 - HE version, - INVERTER, - Plate heat exchanger, - EC brushless fans, - Direct start of the compressors, - Compressor on/off valves, - Microchannel condenser coil, - Complete enclosure of the compressors - Smaller evaporator than the standard unit - Smaller Ziehl fans with an 800 mm diameter. Cooling capacity (kW): 164 Chilled water temperature outlet/inlet (°C): 7 / 12 Flow rate (m³/h): 28.9 Available head pressure bar: 0 Ambient temperature (°C): 35 Refrigeration circuit: Refrigerant R290 Refrigeration circuits (number): 2 Compressors (number): 1 + 1i Power levels (%): 25 to 100, continuously adjustable Electrical data: Voltage V 400, Frequency Hz 50, Phases Ph 3, Max. power consumption (kW): 67 Max. current (A): 117 Starting current circuit (A): 315 Protection class: IP54 Dimensions: Length (mm): 3541, Width mm 2241, Height mm 2425 Weight (kg): 2634 Connection: Vitaulic DN 80 Serial No.: 2200xxxxx Year of manufacture: 2024 Condition: Optically 1, Technically ok Stored unit, new Price: on request in Euro (plus VAT, ex works MTA Italy) – 12 months warranty (Subject to technical changes and prior sale!) Location: MTA, Tribano

Condition: used, Year of construction: 1998, functionality: fully functional, type of input current: three-phase, cutting height (max.): 160 mm, cutting width (max.): 450 mm, saw blade diameter: 450 mm, working width: 870 mm, track width: 450 mm, chain width: 450 mm, disc diameter: 450 mm, – very good condition – manufactured in the Czech Republic – year of manufacture: 1998 TECHNICAL SPECIFICATIONS: Lodpfx Asxtabxenxeag – track width: 450 mm – cutting height: 160 mm – max. blade diameter: 450 mm – main motor power: 45 kW – min. cutting length: 800 mm – max. input material width: 870 mm – shaft diameter: 65 mm – sleeve diameter: 80 mm – feed adjustable via frequency inverter – feed speed range: 4-40 m/min – three rows of anti-kickback pawls – connection spigot diameter: 300 mm – dimensions (L/W/H): 240 x 210 x 200 cm – weight: 3300 kg

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, overall weight: 1,625 kg, product height (max.): 50 mm, product length (max.): 3,080 mm, product width (max.): 2,500 mm, TECHNICAL DETAILS Print Head Technology: Piezo inkjet technology with variable drop size Drop Size: 6–42 pl Ink Type: UV-curing inks Canon IJC357 or IJC358 Color Channels: 8 Standard Color Configuration: CMYK, White, Varnish, Light Cyan, and Light Magenta Maximum Media Area: max. 308 × 250 cm Maximum Printable Area: max. 309 × 251 cm Maximum Media Thickness: max. 50.8 mm Maximum Media Weight: max. 34 kg/m² Vacuum System: Independent vacuum zones for secure hold without taping Edge-to-edge printing possible RMO Specifications Maximum Roll Width: max. 220 cm Minimum Roll Width: min. 90 cm Maximum Roll Diameter: max. 24 cm Maximum Roll Weight: max. 50 kg Core Diameter: 3 inches Core Diameter approx.: 7.6 cm Speed and Productivity Maximum Throughput: max. 52.8 m²/h Production Mode: approx. 27.0 m²/h Quality Mode: approx. 19.8 m²/h MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): approx. 3,830 x 4,660 x 1,300 mm Weight: approx. 1,625 kg Power Supply: 2 × 200–240 V Frequency: 50/60 Hz Fuse Rating: 16 A Compressed Air: 6 bar Laodpfx Anozy Ngdjxjg EQUIPMENT RMO for roll media UV-curing inks Canon IJC357 or IJC358 Independent vacuum zones Edge-to-edge printing function Compressed air connection for cleaning and static control

Condition: reconditioned (used), Year of construction: 1988, functionality: fully functional, machine/vehicle number: 87A, total width: 2,400 mm, total length: 10,500 mm, total height: 2,300 mm, cutting length (max.): 670 mm, type of input current: three-phase, overall weight: 9,000 kg, Holweg RS2 (42GL) Year 1988 Ledey Iclxopfx Anxeag Brand: Holweg Model: RS2 (42GL), modified for standard single-channel RS21 operation Year: 1988 For the production of flat-bottom paper bags, with or without gusset. Machine overhauled: new electrical components, new 3-phase main motor with frequency inverter, unwind station with new Renova Italy electronic brake system and dancer roller. Equipped with inline 4-color flexographic printer model IS 80, maximum print width 800 mm. Printing sleeves included: 4 x 220 mm, 3 x 320 mm, 1 x 370 mm, 1 x 380 mm, 4 x 400 mm, 4 x 430 mm, 4 x 440 mm, 1 x 520 mm, 3 x 520 mm, 3 x 580 mm, 6 x 660 mm, 3 x 680 mm. Gears: - 320 mm: 4 printing gears + 2 machine gears - 340 mm: 4 printing gears + 2 machine gears + 1 printer gear - 380 mm: 4 printing gears + 2 machine gears + 1 printer gear - 440 mm: 4 printing gears + 2 machine gears + 1 printer gear - 520 mm: 4 printing gears + 1 machine gear - 580 mm (290): 4 printing gears + 2 machine gears + 1 printer gear - 680 mm: 4 printing gears + 2 machine gears + 1 printer gear Forming plates: 1 x 90 mm, 1 x 120 mm, 1 x 140 mm, 1 x 150 mm, 1 x 170 mm, 1 x 180 mm, 1 x 200 mm, 1 x 240 mm, 1 x 300 mm. Note: Gluing knives for different bag widths are not included. Printer shafts/adapters: 4 printer shafts included, compatible with the printing sleeves listed above. Perforation type. Max unwinder diameter: 1,200 mm Pneumatic shaft: 70 mm Max paper width: 900 mm Min–max bag width: 70–340 mm (current owner produced only one bag size: 140 mm width x 260 mm length) Cut-off length: 190–680 mm Min–max bag length: 180–670 mm Working speed: 400–800 bags/min (depending on bag size) Suitable paper: 30–70 g/m² Machine can be inspected in operation. Immediately available.

Condition: good (used), Frequency converter, frequency inverter, drive converter, controller, variable speed drive, single motor module, double motor module -Manufacturer: Siemens, Sinamics Double Motor Module -Type: 6SL3120-2TE21-8AA0 A5E33512929 FS: D -Input: DC 510-720 V 43 A -Output: 3 AC 0-480V 18A/18A 0-550Hz A -Number: 3x module available -Price: per piece Lodpfx Anjxni S Noxsag -Dimensions: 480/50/H270 mm -Weight: 7.9 kg/piece

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, REX BIGMASTER Planer A+D+FR+FL+AFV+NSH+HFRo+HFRu 6 spindles + 2 chamfering units. Spindle arrangement: U-O-L-R-O-U Feed rate controlled by frequency inverter up to 80 m/min. Ledjzrtn Nspfx Anxsag Planing width 310 mm. Planing height 205 / 300. Positioning control. Electrical control cabinet with control unit and power supply. Control panel. Soundproof cabin. 2 sets of tools. Technical documentation.

Condition: new, Number of spindles 6 St. Working width 15 - 250 mm Working height 10-200 mm Length of the planing table 2000 mm Feed motor 4 kW Feed speed 6-24 m/min. Kuper SWT XL-6 Automatic Planer and Moulder (Window Version with Glazing Bead Separation) ----- - ??Number of spindles: 6 (Bottom, Right, Left, Top, Top, Bottom) - Working width: 15 - 250 mm - Working height: 10 - 200 mm - Spindle speed: Frequency-controlled 4,000 - 8,000 rpm - Feed speed: 6 - 24 m/min, infinitely variable - Feed motor with electronic brake: 4 kW - Equipped for glazing bead separation in window production - Motorized axial and radial spindle adjustment - K2 Comfort Control, Professional - 9" Touchscreen Manufacturer's Description (Summary): ----- 1st Spindle: HORIZONTAL BOTTOM ----- Siemens IE3 motor with inverter brake: 7.5 kW Diameter: 40 mm Spindle length: 275 mm Speed, frequency-controlled: 4,000 - 6,000 rpm Tool cutting circle: 125 - 160 mm Rebating unit: 20–25 mm diameter difference relative to planing head Important: Machine cannot be operated without the jointing/rebating cutter Extraction nozzle: D = 125 mm "Pro-Lock" tool clamping system 2nd Spindle: VERTICAL RIGHT ----- Siemens IE3 motor with inverter brake: 7.5 kW Diameter: 40 mm Ljdezrh E Nopfx Anxsag Spindle length: 176 mm Clamping length (effective length): 170 mm Speed, frequency-controlled: 6,000 - 8,000 rpm Tool cutting circle: 112 - 200 mm Axial adjustment range: 60 mm Table plate adjustable to tool radius Standard profile depth 20 mm Extraction nozzle dia. 125 mm Extraction; individually adjustable chip deflector "Pro-Lock" tool clamping system Motorized radial positioning Motorized axial positioning 3rd Spindle: VERTICAL LEFT: ----- Siemens IE3 motor with inverter brake, 7.5 kW Diameter 40 mm Spindle length 176 mm Clamping length (effective length) 170 mm Speed, frequency-controlled 6,000 – 8,000 rpm Tool cutting circle 112 – 200 mm Axial adjustment range 60 mm Standard profile depth 20 mm Table plate adjustable to tool radius Extraction nozzle dia. 125 mm Extraction; individually adjustable chip deflector (chips discharged downwards) "Pro-Lock" tool clamping system Motorized radial positioning Motorized axial positioning 4th Spindle: HORIZONTAL TOP: ----- Siemens IE3 motor with inverter brake, 7.5 kW Diameter 40 mm Spindle length 260 mm Speed, frequency-controlled 6,000 – 8,000 rpm Tool cutting circle 112 – 200 mm Axial adjustment range 20 mm Pneumatic pressure shoe, dynamically adjustable via linear guides Pressure lips in front of the spindle: pneumatically sprung, externally adjustable, with path control Standard profile depth 20 mm Extraction nozzle dia. 125 mm Extraction; individually adjustable chip deflector "Pro-Lock" tool clamping system Motorized radial positioning Motorized axial positioning 5th Spindle: HORIZONTAL TOP: ----- Siemens IE3 motor with inverter brake 7.5 kW Diameter 40 mm Spindle length 260 mm Speed, frequency-controlled 6,000 – 8,000 rpm Tool cutting circle 112 – 200 mm Axial adjustment range 20 mm Standard profile depth 20 mm Extraction nozzle dia. 125 mm Extraction: individually adjustable chip deflector "Pro-Lock" tool clamping system Motorized ...

Condition: used, Year of construction: 2016, Overview Ljdpfszvqi Ssx Anxsag Complete craft microbrewery around a 250-litre batch brewhouse - the Slowbeer 250, built in 2016 by Škrlj d.o.o. (Slovenia). The package covers the whole process from malt crushing to bottling - brewhouse, two 1,000 L fermenters, hot water tank, glycol chiller, 4-spout bottling unit and malt mill. All main units date from 2016 - a turnkey set for a brewpub or a start-up brewery. Technical data - Brand: Slowbeer - main units built by Škrlj d.o.o., Slovenia - Model: Slowbeer 250 - Škrlj COMPACT BREWHOUSE MINI 250 L (type BHM 250, 2.5 hl) - Year of manufacture: 2016 - Batch capacity: 250 L - Heating: thermal-oil jackets, electrically heated - 400 V, 50 Hz - Material: stainless steel AISI 304 (EN 1.4301), vessel and jackets - Fermentation capacity: 2 x 1,000 L (nominal) Scope of Delivery - Compact brewhouse | Škrlj (Slowbeer 250) | COMPACT BREWHOUSE MINI 250 L | 250 L per batch, thermal-oil heated, agitator with Bonfiglioli gear motor, Lowara CO350/03K/A wort pump (2019), Pedrollo NGA 1B thermal-oil pump, IPROS TP4001/15 plate heat exchanger, control cabinet with Omron frequency inverters | 2016 - Beer fermenters, 2 units | Škrlj | ZKG 1000 L | nominal 1,000 L each (1,230 L gross volume per vessel), AISI 304, atmospheric vessel 0-50 °C, water/glycol cooling jackets on shell and cone (3.0 bar operating, 6.0 bar test), sample valve, level indicator, CIP spray ball; recirculation pump with cleaning hoses plus one unused spare pump | 2016 - Hot water tank | Škrlj | 1200 L | AISI 304, electric heating 24.4 kW, 0-90 °C, CE 0531 | 2016 - Glycol chiller | MTA | TAEevo TECH 020 | 400 V / 3-ph / 50 Hz, 3.9 kW electrical input, refrigerant R410A, water circuit max. 6 bar, hose circuit for the fermenter jackets, digital temperature control | 2016 - Gravity bottling unit | Mori-Tem | MODERNA B.4 A LE | 4 stainless steel filling spouts, Ebara JESX M5 feed pump, 230 V single-phase 50 Hz | 2016 - Malt roller mill | Egon Sommer Maschinenbau | PICCOLO 11 SB | 1.1 kW three-phase motor (230/400 V) | 2016 Transport dimensions (palletised, approx.) - Brewhouse: 2,400 x 1,200 x 2,200 mm, 660 kg - Fermenters (each): 2,700 x 1,100 x 1,245 mm, 240 kg - Hot water tank: 1,210 x 1,210 x 2,245 mm - Glycol chiller: 1,300 x 600 x 955 mm, 220 kg - Bottling unit: 1,000 x 700 x 1,650 mm, 180 kg - Malt mill: 800 x 600 x 1,200 mm, 90 kg Condition Used - very good to excellent overall condition. Brewhouse, fermenters and malt mill in excellent condition; chiller and bottling unit in good working order. The hot water tank is fully functional, with a light cosmetic dent on the top cover and normal limescale deposits inside. CE declarations and technical documentation are available for every unit except the malt mill, where the documentation is still being confirmed. Availability Immediately. Location: Spain. Dismantling and loading by arrangement.

Year of construction: 2008, condition: used, Technical specifications: - Manufacturer: Venjakob - Model: H - Working width: 1,300 mm - Length: 21,500 mm - Total width: 1,510 mm - Feed speed adjustable via frequency inverter - Frequency inverter not included in delivery - Height: 900 ± 50 mm - Motor power: 0.81 kW - Motor ATEX-compliant - Belt control, pneumatic - Max. load: 70 kg/m - Colour: RAL 7035 light grey - Voltage fluctuations: ±5% - Location: in stock Laedpozv Tgmjfx Anxjg

Condition: used, Year of construction: 2004, functionality: fully functional, overall weight: 2,000 kg, SCM Sandya 7S wide belt sanding machine Working width: 1100 mm Sanding height: 4–160 mm 1 metal sanding head, 11 kW 2 combi sanding heads, 11 kW Adjustable speed of the combi sanding head via frequency inverter Electric height adjustment Ledpfszykr Usx Anxjag Optical oscillation Adjustable feed speed via variator: 3–17 m/min Vacuum pump Technical documentation and CE certificate Year of manufacture: 2004

Condition: ready for operation (used), Control Techniques SE43401500 SE 22T Commander frequency inverter, serial number 3960768008 / the cover is loose and has minimal damage, see pictures!! Used, in good condition, 100% functional, scope of delivery as shown in the photos. Ledpfxjzzurzo Anxoag

Condition: used, mileage: 19 km, power: 130 kW (176.75 HP), first registration: 10/2025, fuel type: diesel, color: white, gearing type: automatic, number of seats: 3, total length: 5,986 mm, total width: 2,040 mm, total height: 2,355 mm, Equipment: ABS, air conditioning, all wheel drive, central locking, electronic stability program (ESP), navigation system, parking heater, soot filter, * Approved as a 3.88t vehicle * Approved total weight * Standard climate zones * Electronic Stability Program (ESP) * Tow hitch, detachable and lockable * One towing eye at the front * Disc brakes at the front * Increase of approved total weight from 3.5t to 3.88t * All-wheel drive * Leather multifunction steering wheel, heated with Tiptronic * Partition, without window * Three-point automatic seat belts at the front with electric belt tensioner * Normal roof * Double bench seat in the cab on the right with storage compartment * Driver's seat on the left * Extended interior noise reduction * Seat heating for front seats, separately adjustable * Windshield in heat-protective glass, heated * Central locking "Keyless-Go" without safe lock * Safety interior mirror, dimmable * Dashboard with special fittings * Exhaust concept, WLTP3 N1-III, N2//EU6EC * Airbags for driver and front passenger, without knee airbag, with front passenger airbag deactivation * Rubber floor covering in the cab * Wooden floor in the cargo area * Lateral interior paneling in the cargo area (up to the roof frame) made of plywood * Incomplete truck approval * Sliding door on the right in the cargo/passenger compartment * Exterior mirrors left and right, convex plus wide-angle * Hinges for rear doors with enlarged opening angle * Sun visors with mirror * 2nd heat exchanger plus 2nd evaporator * Lashing eyes for securing cargo * Lane assist plus emergency assist and traffic jam assist * Radiator protection grille * Rear mud flaps * Interior grab handle (entry at the partition) * Exterior mirrors, electrically foldable, electrically adjustable, separately heated * Immobilizer, electronic * Entry handles on the rear pillar, left + right * Speed limiter up to 90 km/h * Tire pressure monitoring, frequency 433 MHz High * Start/stop system with recuperation * Navigation system (Baseline) * Auxiliary heating with air and water heating, programmable * Park assist * Optional infotainment (MIB3 MP) version 2 * Second battery * High beam assistant * LED headlights * Front Assist with warning and braking for vehicles, pedestrians and cyclists * Windshield wiper intermittent control with light/rain sensor * Key for locking system with remote control * 4 speakers (passive) * Automatic distance control * Fog lights and turning lights * Headlight cleaning system * LED interior lighting concept in the passenger/cargo area * Daytime running light with assistant driving light and coming/leaving home function, automatic * Comfort telephony with LTE and wireless charging * Preparation for Smart TCO * Seat belt control, E-contact in the seat belt buckle * Wired & Wireless App-Connect * 230V inverter and socket for Europe * Country cluster "WLTP EU approval" * BSIS driving direction right, with MOIS * 4-cylinder turbo diesel engine 2.0 L / 130 kW (4V) TDI * Online service, with OCU, with head unit coding, without WFS connection * Distraction and fatigue detection * With socket at the front * 8-speed automatic transmission for all-wheel drive * Preparation for alcohol interlock * Acoustic warning system for engaged reverse gear, can be switched off * Battery 520A (92Ah) * With rear view camera system (version 2) Lajdpfxozx Nabs Anxeg * Air conditioning with electronic control * With crosswind assist * With predictive speed limiter (pLIM) * Seat covers in imitation leather * With UNECE CS&SU * Pan-European eCall * Air conditioning with manual control with additional cooling for the cargo area * Light alloy wheels "Li

Condition: ready for operation (used), functionality: fully functional, Danfoss VLT 5022 – Type VLT 175Z4123 1 unit in stock We have a wide range of Danfoss frequency inverters available, including this type: VLT 5022 175Z4123. Lajdpfx Aozkr Dysnxjg With this advertisement, we have included an overview with photos. It is also possible to request additional photos of a specific part. Please feel free to send us a message for this. A PDF file has also been added, containing an overview of all Danfoss parts that we currently have in stock. Do you have any questions or are you looking for a specific Danfoss part? Please feel free to contact us. We will be happy to assist you.

Condition: new, Steel Frame Automatic Nailing Bridge A fully automatic nailing station for nailing or stapling sheet materials in accordance with the design specifications including the following functions: ​ 1. Nailing or stapling of sheeting 2. Routing of openings or overhangs 3. Application of breather membrane 4. Nailing or stapling of battens ​ Specification Full PC control with 17” touch screen Interactive display of operation being performed Automatic download from drawing software. Heavy duty tables with one fixed side and one moving side 90 degree squaring corner blocks with pneumatic retraction to enable panel to move to next position when finished 1300mm minimum panel height Maximum panel height up to 3.5m (optionally extendable) Maximum panel length 6m – optionally up to 13m 400mm wide heavy duty work tables 825mm working height 300mm maximum panel thickness (optionally 5000mm) Motorised table opening with automatic brake locking Bridge mounted with one nailing / stapling tool mounting as standard. (Options for 2 or 3 nailing tool mounts) Full integration with major software packages including Sema, Dietrich;s, HsbSoft, CADWORKS, Gang Nail & Mitek. Batten application system with guide to ensure they battens are kept straight before nailing including batten storage area Pneumatic lifting rollers to assist the manually transporting of the finished panel to next position. Optional electrically driven sheet feeding system, including automatic sheet feeding and height indexing of the support table. Optional router unit with 4kw motor - servo drive controlled Optional Equipment ​ Table with rails mounted for bridge Additional price per meter for table with rails mounted Ljdpfx Asdzc Rxonxjag Independent rails to travel 8m over one 6m capacity table (16m of rail in total) Additional price per meter of rail Working table for holding panel 6m (no rails mounted) Additional price per meter for table Motorised chains rather than manual rollers - initial cost Price per meter for motorisation Baton positioning guiding arrangement Additional tool mount Paper roll clamp, holder and software Electric paper cutting Panel thickness of 500mm Saw blade in X, Y, Z & C axes 350mm max panel thickness Saw blade in X, Y, Z & C axis 500mm max panel thickness. Inclination of the sawblade to one fixed angle Router complete with frequency inverter, mounted on the bridge for routing out openings in the panels. Complete with software controls and dust extraction.

Year of construction: 2000, condition: reconditioned (used), functionality: fully functional, machine/vehicle number: 071, Stock no. 2806 1 used, partially overhauled, and functionally tested strand granulator Type SG-60 E Ledpsz A R Ilofx Anxsag Cutting rotor with single-sided bearing Rotor diameter 160 mm x width 70 mm Rotor with helical cut, 30 teeth, 2° Strand inlet width: 60 mm Up to 12 strands according to the manufacturer Cutting chamber with sound insulation 2.5 kW - AC drive, adjustable via frequency inverter Ready for demonstration at our plant in Wuppertal We have other strand granulators ready for demonstration. Please inquire about our current machine stock list.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2007, machine/vehicle number: A0220A1818, laser power: 3,200 W, overall weight: 11,700 kg, TECHNICAL DETAILS Laser power: 3,200 W MACHINE DETAILS Input voltage: 400 V Input frequency: 50 Hz Input current: 125 A Control voltage: 24 V Required fuse rating: 3 × 125 A Compressed air connection: 7–10 bar Nitrogen connection (N₂): 30 bar Lajdpfx Aoz Ahrwjnxjg Oxygen connection (O₂): 20 bar Connected power: 73 kVA Dimensions & Weight Dimensions (L x W x H): 9,229 x 6,145 x 2,200 mm Total weight: 11,700 kg EQUIPMENT CE marking Documentation / Manual Dust extraction Emergency stop switch Safety light curtain

Condition: excellent (used), Catalog number: 8060 TECHNICAL DATA - max. width of workpiece: 230mm - max. height of workpiece: 180mm - number of spindles: 5 Laedpfxezx Spxs Anxjg 1) horizontal lower: 230mm, 7.5kW 2) vertical right: 180mm, 5.5kW 3) vertical left: 180mm, 5.5kW 4) horizontal upper: 230mm, 7.5kW - 4 spindles with electric up/down adjustment from the control panel 5) horizontal lower: 230mm, 7.5kW - all heads adjustable up/down, left/right - spindle diameter: 40mm – top: - 6 feed rollers, toothed, including 2 double rollers - 2 feed-out rollers, rubber – bottom: - feed roller, toothed, driven, with swivel mechanism in the lower table, in front of the first spindle - 2 pneumatic side pressure rollers - feed-out roller, metal, smooth - all rollers with pneumatic pressure - length of feed table: 2180mm - table adjustable up/down - central lubrication - electric adjustment of planing thickness - lifting motor approx. 1.1kW - stepless feed speed control via frequency inverter - feed motor: 3kW - feed via Cardan shafts - enclosed in a cabinet - diameter of dust extraction nozzle: 5x150mm - dimensions (L/W/H): 4100x1750x1900mm - weight approx. 3800kg ADVANTAGES – with 5 heads – ideal for wet and dry wood – DTR documentation – used machine, very good condition Net price: 68900 PLN Net price: 16405 EUR, depending on the exchange rate of 4.20 EUR (Prices may vary due to significant exchange rate fluctuations)

Condition: new, Year of construction: 2024, functionality: fully functional, operating hours: 10 h, cutting height (max.): 510 mm, cutting width (max.): 510 mm, rotational speed (max.): 80 rpm, rotational speed (min.): 20 rpm, controller model: Siemens SIMATIC S7-1200, For sale is a brand new, unused semi-automatic band saw! The machine is sold with a six-month warranty! TECHNICAL DETAILS Cutting height: 510 mm Cutting width: 510 mm Speed range: 20 – 80 RPM Speed infinitely adjustable Band saw width: 54 mm Band saw thickness: 1.6 mm Swivel range: 90 ° Table height: 810 mm MACHINE DETAILS Ljdpfoz Aq Nfsx Anxjag Control model: Siemens SIMATIC S7-1200 Control type: PLC-controlled Operating mode: semi-automatic Main drive power: 7.5 kW Power: 10.20 hp Hydraulic feed Planetary gearbox Input voltage: 400 V Input frequency: 50 Hz Input current type: Three-phase Dimensions & Weight Dimensions (L x W x H): 1,200 x 3,200 x 3,000 mm Total weight: 4,500 kg EQUIPMENT Heavy-duty double-column construction CE marking Documentation / Manual Lighting Motor brake Further technical data and information can be found in the attached documents.

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, paper weight (max.): 208 g/m², paper width (max.): 350 mm, paper height (max.): 500 mm, production capacity: 4,500 unit/h, No minimum price – guaranteed sale to the highest bidder! Auction of a brochure production line! TECHNICAL DETAILS Gathering towers Models: Horizon VAC-100a / VAC-100m Number of towers: 2 Stations per tower: 10 Feeder system: Air suction feeder Voltage: 230 V Frequency: 50 Hz Current draw: 10.4 A per section Booklet making and folding module Model: Horizon SPF-200A Voltage: 230 V Frequency: 50/60 Hz Current draw: 3.4 / 3.2 A Booklet making heads: 2 Brochure thickness: up to 4.5 mm Functions: Wire stitching and center folding Front trimmer Model: Horizon FC-200A Function: Automatic front trimming Operating mode: Inline operation with Horizon SPF-200A Cutting quality: High-precision cut Stacking unit Model: Horizon ST-40 Voltage: 230 V Lodpfszy Hhxjx Anxjag Frequency: 50 Hz Current draw: 4.7 A Function: Automatic stacking of finished brochures Production capacity: max. 4,500 brochures/h Feeder stations: 10, expandable to max. 60 Sheet format max.: approx. 350 × 500 mm Paper weight: 52–208 g/m² Booklet thickness: max. 2 mm for saddle stitching Processing: Gathering, stitching, folding, and stacking in one system MACHINE DETAILS Production counter: approx. 1,800,000 brochures EQUIPMENT Horizon VAC-100a gathering tower Horizon VAC-100m gathering tower Horizon SPF-200A booklet making and folding module Horizon FC-200A front trimmer Horizon ST-40 stacking unit Data sheets for the individual components of the system, including further detailed technical data, can be found in the appendix.

Condition: excellent (used), Year of construction: 2008, operating hours: 282 h, Calibrating and finishing machine, wide belt sanding machine with electronic segmented sanding pad and finishing sander Ideal sanding machine for interior design companies, also suitable for intermediate sanding of lacquered surfaces. Edge banding machine with combination unit and electronic articulated pressure bar, edge segments can be switched on and off. Segment width of the pressure bar: 35 mm Contact roller can be pneumatically adjusted, low wear due to ribbed steel roller Grain size compensation Drive motor 7.5 kW with automatic motor brake, stepless belt speed controlled by frequency inverter from 2 - 18 m/s Lasdpfx Anozqvmrjxog Belt feed speed can be steplessly adjusted via frequency inverter from 2.5 - 13 m/min Pneumatic workpiece-controlled belt blowing device Cleaning brush at the discharge end Constant working height of 900 mm by adjusting the upper part of the machine, thus can also be integrated into sanding lines. Feed belt still has good grip and is in very good condition. Maximum sanding width approx. 1340 mm Workpiece height approx. 3 to 150 mm Common sanding belt dimension: 1360 x 1900 mm 3 rubberized pressure rollers Infeed roller table and foldable discharge table Preparation for vacuum blower. The carpet is perforated and connectors for an optional blower are available. Alternatively, the carpet can also be connected to the extraction system. Extraction connection: 1 x 200 mm, 1 x 140 mm, and 2 x 100 mm Terminal control with 50 programmable sanding programs for automated machine control. Parameters: Belt speed, feed speed, workpiece height, pressure bar setting points at the front and rear, as well as edge segments, belt blowing nozzle, optional vacuum blower, pneumatic adjustment of the calibrating roller. CE marking Operating manual Without the illustrated connection cable Original paint, only retouched in some areas Approx. 282 operating hours, i.e. approx. 20 minutes per week. Dimensions approx. 1800 (with table 2600) x 2050 x 2150 mm (L x W x H). Weight approx. 2400 kg. The machine can be demonstrated on site after prior arrangement. We only offer machines that are ready for demonstration in our warehouse; see "other offers from this provider".

Condition: used, Tank rotating device, roll rotating device, welding rotating device, boiler rotating device Manufacturer: GSD Lsdpfx Aezgx A Isnxeag Tank rotating device for welding pipes and tanks Year of manufacture: 2012 Load capacity of the rotating device: 40 tons Rotation speed: 0 to 3.2 m/min Tank diameter: 500 - 7000 mm Roller spacing: 200 to 1750 mm Roller center distance: 600 to 2150 mm Roller diameter: 400 mm Roller width: 480 mm Motor power: 2 x 1.5 kW Mains connection: 400 volts, 50 Hz - Variable speed control via SEW frequency inverter - Cable remote control - Clockwise and counterclockwise rotation - Both roller pairs are driven - Rollers with 5 rubber tires each - Manual adjustment of the roller spacing via trapezoidal screw spindle - Railcar DEMAG, steel castors with smooth roller surface (without drive) Space requirement L x W x H: 4000 x 1850 x 1150 mm Own weight: 4.5 t Good condition

Condition: excellent (used), Year of construction: 2011, 16768 MANUFACTURER: KAESER MODEL: SK25 Serial No.: 1015 Year: 2011 Power (kW): 15 Output (m3/min): 2.25 Pressure (bar): 11 Operating hours (DOC/TOTAL): 19238/36933 Frequency inverter: no Built-in dryer: no Heat exchanger: no Cooling (air/water): air Mounted on tank: no Documents: no Laodpfxjy Sitde Anxsg Connection: 3/4

Condition: used, Roller conveyors with chains pull 90° RA1846 Type: Transnorm 3300-600-550 Length: FL = 3300 mm Conveyor width: FB = 550 mm Total width: 600 mm The chains off slide width: 700 mm height (BH): 140 mm Support roller pitch: 80 mm including pneumatic stopper Optionally available: Supports Side guide one and both sides frequency inverter Prices net plus VAT from central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Ljdpfxek Abg Do Anxoag Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics

Condition: used, Year of construction: 2012, Transnorm curved belt conveyor right 40°-780-600 RA1848 Make: Transnorm Running direction: 40° right running belt conveyor width (RB): 600 mm Laedpfxsk Abg Ss Anxeg Nominal/outer width (NB): 780 mm Inner radius (IR): 600 mm V230/400 kw 0,37 Height frame: 280 Scope of delivery:with motor, without supports (please enquire if required) Optionally available: Supports Side guide one and both sides frequency inverter For individual, expert advice, simply get in touch with us. Simply contact us by phone or email. We will be happy to help you plan and implement your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics