Used Handwheel for sale (1,215)

Condition: ready for operation (used), Year of construction: 2012, operating hours: 3,006 h, functionality: fully functional, turning length: 1,540 mm, travel distance X-axis: 495 mm, travel distance Y-axis: 125 mm, travel distance Z-axis: 1,560 mm, swing diameter over bed slide: 660 mm, controller model: MSX-711 (MAPPS IV), Partially overhauled machine with only approximately 3,000 spindle hours! TECHNICAL DETAILS Kedpfx Ajx An Uxeh Usnf Turning length: 1,540 mm Max. turning diameter: 610 mm (Turret 2: 274 mm) Swing diameter over bed: 660 mm Swing diameter over cross slide: 660 mm (Turret 2: 300 mm) Turning/Milling Spindle X-axis travel: 495 mm Y-axis travel: 125 mm Z-axis travel: 1,560 mm B-axis: 120 degrees Spindle speed: 12,000 rpm Drive power: 18.5/11 kW (10 min./continuous operation) Tool Magazine Magazine positions: 76 Tool holder: Capto C6 Lower Turret Number of tool stations: 10 Tool change time: 0.19 s Main Spindle Spindle speed: 5,000 rpm Main spindle drive power: 22/18.5 kW (30 min./continuous operation) Sub Spindle Spindle speed: 5,000 rpm Sub spindle drive power: 22/18.5 kW (30 min./continuous operation) MACHINE DETAILS Control system: MSX-711 (MAPPS IV) Operating hours Spindle hours: 3,006 h Operating hours: 4,526 h EQUIPMENT Spindle 2 with tailstock option Electronic handwheel Interface for high-pressure coolant system Chip conveyor Air nozzle for chuck and tool tip Automatic tool measurement system for upper and lower positions Bar feeder interface Hobbing function

Condition: good (used), Year of construction: 1984, Used TOS KAMENICEK model BUC63A x 3000 Universal cylindrical grinding machine. YEAR OF MANUFACTURE: 1984. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION Max Swing 630 mm Distance between centres 3000 mm Kjdpfoh U Rznex Ah Ujnf Workhead swivel – towards wheelhead only 90 deg. mm Work spindle bored taper No. 6 M.T. Length of stroke of tailstock barrel 70 mm Tailstock barrel taper No. 6 M.T. Spindle nose clamping Din 55021 Swivelling of wheelhead + 30 deg – 10 deg Length of adjustment by re-circulating ball screw 290 mm Additional length of adjustment 250 mm Length of rapid feed 90 mm Length of infeed setting per each rev. of handwheel, measured on work diameter 0.5 mm Grinding wheel dia. X width X bore 750 x 80 x 305 mm Min. dia. of worn grinding wheel 570 mm Max. face width of grinding wheel 125 mm Rate of table traverse – steplessly variable 0.5-0.6 m/min Table traverse per 1 rev of handwheel 8 mm Swivelling of table +/- 5 deg. Max. permissible weight of work between centres 2500 kg Max. permissible weight of workpiece in chuck with overhang. (including weight of chuck) 150 kg Wheel spindle speeds (2) 840,970 rpm Grinding wheel surface speed 33 m/sec Work spindle speeds – int. var. in 2 ranges 8-50, 50-315 rpm Drive – total power required rated 31 kva Output of workhead motor 3 kw Output of wheelhead motor Electrics 15 kw 415V ,3Ph,50Hz Equipped with:- Additional wheel flanges, coolant system with clarifier and splash guards. FEATURES AND EQUIPMENT – Swivel Round Internal Grinding Attachment

Condition: used, Year of construction: 2003, x-travel 350 mm y-travel 240 mm z-travel 340 mm Ksdpfsx A H R Sex Ah Uenf b-axis -15 / +105 ° c-axis 360 ° control SINUMERIK 810 D SIEMENS spindle taper SK 40 spindle turning speed range 20 - 6.300 U/min table-size Ø 400 x 290 mm table load 100 kg feeds -stepless- 5.000 mm/min rapid traverse 5,0 m/min power capacity 6,3 / 10,0 kVA voltage 400 V total power requirement 15,0 kVA weight of the machine ca. 1,6 t dimensions of the machine ca. 1,75 x 1,60 x 2,10 m coolant tank 1,10 x 0,30 x 0,40 m - Serial-No.: 11065356904 - Machine ON: 37,474 h - Spindle ON: 1,428 h - Control: Sinumerik 810 D / Shopmill - Electronic handwheel - machine table pivotable - Manual rotation/pivotation of machine table with DRO display on CNC screen - Swivel range b-axis -15° / +105° - Swivel range c-axis 360° - Coolant device - Siemens CCU-Unit changed Dec.2025

Condition: new, The Servomill® FPK 500 is a state-of-the-art Conventional Vertical Milling Machine from KNUTH, designed for superior performance in toolmaking and mechanical manufacturing. This versatile tool seamlessly integrates modern electronics, making it intuitive and capable of operating with exceptional precision. Its robust construction features a console design made of high-quality grey cast iron, ensuring durability and dimensional stability during operation. Noteworthy attributes include powerful servo feed technology with electronic handwheels, enabling infinite variability in feed speeds and precise control across all axes, accompanied by ball screws that eliminate backlash for enhanced accuracy. With a comprehensive variety of standard equipment such as a coolant system, LED worklight, and an automatic lubrication system, the Servomill addresses operational efficiency while minimizing maintenance needs. Perfect for both skilled operators and training environments, this machine exemplifies the best in modern milling technology. Whether you're looking to enhance your production capabilities or train the next generation of machinists, the Servomill® FPK 500 is an ideal choice. Request a quote today to elevate your milling operations with this advanced Conventional Vertical Milling Machine. Knodpfxjwa Ah Rj Ah Ujf

Condition: excellent (used), Year of construction: 2022, Machine type: CNC Vertical Machining Center Model: CMX1100V Manufacturer: DMGMORI Control: DMG MORI SLIMline® Multi-Touch Heidenhain Year of manufacture: 2022 Location: Germany Options: - Main spindle 12,000 rpm 13/9kW SK40 - Tool holder BT 40 for pull studs DIN 69872 - Direct absolute measuring system X-Y-Z Knjdpjx Dr Dysfx Ah Uof - Magazine with 30 tool stations - Through-spindle coolant supply (IS) 20 bar - Double changeover filter - External coolant air-blast switching via M-function - Chip conveyor (scraper type, left side) - Tank capacity (left side chip conveyor): 250 - Coolant spray gun for chip removal - Automatic cabin roof - Signal lamp - Electronic handwheel - Probe kit for spindle and table Travel range X-axis 1100 mm Y-axis 560 mm Z-axis 510 mm Table size approx. 1400 x 560mm Workpiece weight max. approx. 1000kg Rapid traverse X / Y / Z 30 m/min Floor space (L x W x H) approx. 4.04 x 2.8 x 2.95m

Condition: ready for operation (used), Year of construction: 2000, sheet width 1030 mm plate thickness 12.0 mm thickness at "Niro-steel" 8.0 mm Knedpfx Aexyafdjh Uef blade length 1050 mm cutting angle 3.0 Grad no. of strokes ca. 10 Hub/min back stop - adjustable 500 mm Control konv. table height 900 mm operating pressure max. 280 bar oil volume 150 l engine output 11.0 kW weight 1900 kg range L-W-H 1550 x 1150 x 1600 mm Machine from a maintenance workshop (!) Furnishing: - heavy / robust electro-hydraulic sheet metal plate shears - Machine body in a closed design as an all-steel welded construction - Knife upper cheek slides in a long downward direction over the knife edge . protruding plastic guides - Cutting is done hydraulically via two hydraulic cylinders - The upper beam returns to its starting position in two ways . Spring batteries on the side stands - manual back gauge, adjustable from the rear * Adjustment by handwheel, with mm scale - manual cutting gap adjustment - 1x side stop, with mm scale and T-slot - Foot switch for lifting version - rear sheet metal slide - instruction manual * Machine link: ?machineno=1008-9325319

Condition: good (used), MITRE COLD CIRCULAR SAW MACHINE Type: KKS 400 H Year of manufacture: 1982 Equipment: - Infeed roller conveyor 1000 mm, left - Outfeed roller conveyor with length stop, 2000 mm, right - Saw blade diameter: 370 mm Kedpfjxnmn Usx Ah Ujnf - Hydraulic clamping cylinder with 8 mm stroke, handwheel for pre-setting - Documentation Condition: good, workshop inspected

Condition: good (used), Year of construction: 2002, functionality: fully functional, USED Soraluce Soramill Model SP 10000 Travelling Column, Table Type CNC Milling Centre, with Automatic Oil Mist Lubricated Orthogonal Milling Head with 1 X 1 Degree Indexing and HEIDENHAIN TNC 430 M Control System. Year 2002 SN 8647 Table Area - 10000 x 1100 mm Column Traverse (X) - 8500 mm Vertical Traverse (Y) - 1600 mm Ram Traverse (Z) - 1200 mm Spindle Motor - 28 kW Spindle Taper - Standard ISO 50 BT50 tooling Ksdpfx Aor Hr Aroh Uonf Pullstud - DIN 6987 2-Form A. ISO 7388/2-Form A Independent Gearbox with 2 Ranges Speed Range - 20 to 4000 RPM Feed Range - 5 to 5000 mm/min Rapid traverse rate - (X, Y, Z) 15,000 mm/min Preloaded double nuts and recirculating ballscrews to each axis. Linear Guiding System with recirculating cylindrical rollers and steel guideway assemblies in X, Y and Z axes Independent A.C Drive motor to each axis. Linear Transducer in X, Y and Z-axes with air purge system. Automatic tool clamping. Automatic hydraulic tool releasing device. CNC Control HEIDENHAIN TNC-430-M. (Flat TFT screen with digital drives) 9 axes CNC and 1 spindle, 5 of them simultaneously interpolated. Working area lighting Electrical cabinet cooling system Electrical cabinet lighting Heidenhain HR410 portable electronic handwheel with 3m spiral cable Horizontally articulated pendant for CNC control Orthogonal head 28KW, 800Nm, 1deg x 1 deg, 4000rpm oil lubricated Price includes oil cooling unit for both head and gearbox. Option G2, Ram prepared for 4000rpm, is also included. Coolant through the spindle type AD. Coolant system with 500l capacity tank with two pumps providing low and high pressure of 3 and 8 bars and 50l/min flow. The system includes a combined paper and magnetic drum-filtering unit. Standard operators platform fixed to the column 40 tools capacity toolchanger magazine, BT50 Max. Tool length = 400 mm. Max. Tool diameter: - With full magazine = 120 mm. With adjacent position empty = 250 mm. Max. Tool weight = 20 kg. Mean tool weight with full magazine = 10 kg. Max. Permitted total weight = 20 kg. Swarf Conveyor Hinge type conveyor belt Machine preparation for the addition of a 4th axis electro-mechanical table. Splash Guarding against swarf at the table front and both sides. Consists of four sliding front doors with a height from the floor of 2.100mm and a length of 1.700mm each one. Manually operated opening and closing with mechanical interlock. The doors can be opened for the full longitudinal traverse. The rear of the table is open. Protection in the back and both lateral sides of the machine column.

Condition: refurbished (used), Year of construction: 1999, functionality: fully functional, Semi-automatic vertical miter bandsaw Berg & Schmid VGS 500 HA-I Fully refurbished & fully functional + 4m infeed roller conveyor RS 400 + Measuring stop with roller conveyor LM 110 DH (digital & handwheel) Cutting ranges: - 90°: round: 330 mm; square: 330 mm; flat profile: 330 x 160 mm / 320 x 300 mm; upright profile: 160 x 160 mm; rectangular: 500 x 330 mm - 45° left: round: 300 mm; square: 300 mm; flat profile: 330 x 160 mm / 320 x 300 mm; upright profile: 180 x 160 mm; rectangular: 300 x 330 mm - 45° right: - 45° left: round: 300 mm; square: 300 mm; flat profile: 330 x 160 mm / 320 x 300 mm; upright profile: 160 x 160 mm; rectangular: 300 x 330 mm Technical data: - Motor: 2.0 kW / 400 V - Saw band speed: 18 - 110 m/min steplessly adjustable - Saw band dimensions: 4,140 x 34 x 1.1 mm - Weight: 1050 kg - Dimensions: 1900 x 2000 x 2200 mm Knedpfoxqfmnex Ah Ujf Features: - Semi-automatic bandsaw with microprocessor control and hydraulic movement of the saw frame - Cuts in semi-automatic mode with variable angle up to 45° left or right, manual adjustment of the saw frame - Hydraulic vise - Electronic frequency inverter for stepless band speed - Automatic detection of cutting start and end - Saw arm feed rate adjustment via feed regulator - Mechanical blade tensioning monitored by microswitch

Condition: used, Double-column hydraulic press SCHÖN Type UTE/B 50 Machine No. 5509, Year of manufacture 1971 Pressure capacity 50 tons Column width 550 mm Column side clearance 150 mm Table surface 480 x 380 mm Table opening Ø 70 mm Ram surface 490 x 280 mm Clamping pin bore Ø 40 mm Max. ram stroke 150 mm Max. installation height 390 mm Table height above floor 890 mm Rapid forward speed approx. 130 mm/sec. Working speed approx. 20 mm/sec. Return speed approx. 130 mm/sec. Motor power: 4 kW Power supply: 380 volts, 50 Hz - Continuous press force adjustment - Rapid stroke and working stroke Kodpev Srfwefx Ah Uenf - Pressure- or stroke-dependent stroke limitation - Adjustable pressure hold time, press time extension 0.5-6 seconds - Mechanically adjustable fixed stop via handwheel on the ram - SICK light barrier, type LVU - Stroke counter - Double column guide on the ram Space requirement: L x W x H: 1100 mm x 1050 mm x 2320 mm Weight: approx. 1.5 tons Good condition

Condition: good (used), Year of construction: 1988, voltage 380 V connected load 7,5 kVA dimensions 2725 x 1930 x 1773 mm weight of the machine ca. 2500 kg --> Technical data Main data: --> Table surface: 605 x 300 mm --> Table longitudinal movement max. (manual): 750 mm --> Table transverse movement: 340 mm --> Grinding height between table/new grinding wheel min/max: 22.5 / 322.5 mm --> Standard size of magnetic clamping plate: 600 x 300 mm --> Workpiece weight incl. magnet: 420 kg --> X-axis / longitudinal movement: --> T-slots (number x width): 3 x 17 mm --> Table feed, hydraulic: 0.3 - 25 m/min Kjdew Dvkajpfx Ah Ujnf --> Travel per handwheel revolution: 47 mm --> Y-axis / height movement: --> Automatic vertical feed - coarse in 12 steps: 0.001 - 0.03 mm --> Automatic vertical feed - fine in 8 steps: 0.001 - 0.01 mm --> Distance per handwheel revolution (x1/x10): 0.1 / 1.0 mm --> Graduation on handwheel (x1/x10): 0.001 / 0.1 mm --> Trigger strokes: 0 - 5 --> Rapid traverse: 400 mm/min --> Z-axis / transverse movement: --> Automatic transverse feed intermittent: 0.5 - 20 mm --> Automatic transverse feed / rapid traverse continuous: 0.1 - 1.0 m/min --> Distance per handwheel revolution: 5.0 mm --> Scale mark on handwheel: 0.02 mm --> Standard grinding wheel: --> Ø x width: Ø 355x38 (50) mm --> Bore: Ø 127 mm --> Speed: 1500 rpm --> Accessories Various grinding wheels --> Documentation

Condition: new, The HFS 60160 F NC, a robust Conventional Surface Grinder, is engineered to handle large and heavy workpieces with precision required for efficient surface grinding, lapping, or polishing. Its massive cross-bed design provides exceptional rigidity, enabling optimal weight distribution and a long table guidance for consistent performance. The machine features a large grinding spindle that is permanently lubricated, ensuring maximum grinding performance and reliability. Additionally, it is equipped with a powerful cooling system and flexible automatic or manual operation, making it suitable for sample production, repairs, and training. User-friendly Siemens Smart Line PLC control with a touchscreen allows for easy access to editable grinding cycles. The standard equipment includes essentials such as a magnetic clamping plate, electronic handwheel for precise positioning, and a fully enclosed workspace for enhanced safety. When looking for a reliable Conventional Surface Grinder, the HFS 60160 F NC by KNUTH stands ready to meet your machining needs. Request a quote today to experience the efficiency and precision of this exceptional grinding machine. Knsdsww T Tljpfx Ah Usf

Condition: like new (used), Year of construction: 2020, operating hours: 400 h, travel distance X-axis: 550 mm, travel distance Y-axis: 500 mm, travel distance Z-axis: 500 mm, rotational speed (max.): 12,000 rpm, Machine Details Stock-No. 1105-04006 Type of machine: Vertical Machining Center Manufacturer: DMG MORI Model: M 1 Year of manufacture: 2020 Control type: CNC Stored at: HAGUENAU, FRANCE Country of origin: Germany Availability: IMMEDIATE Shipping terms: EX WORKS Technical specifications: Kodpstpcnnjfx Ah Uonf X-axis travel: 550 mm Y-axis travel: 550 mm Z-axis travel: 510 mm table size: 790 x 560 mm Spindle taper: ISO SK 40 Spindle speed range: 10,000 rpm Feed rates (longitudinal/cross/vertical): 1 - 30,000 mm/min Rapid traverse (longitudinal/cross/vertical): 30 m/min Number of tools in magazine: 20 Max. workpiece diameter at full tool load: 80 mm Workpiece diameter with 2 vacant positions: 140 mm Max. workpiece length: 300 mm Max. tool weight: 7 kg Max. table load: 600 kg Spindle drive: 9 / 11 kW CNC control: SIEMENS 828D Total connected load: 30 kVA Additional Information: CNC SIEMENS 828 D Only 1,800 spindle hours Very good condition Electronic handwheel Chip conveyor Tool setter

Condition: good (used), Year of construction: 2002, functionality: fully functional, USED Soraluce Soramill Model SP 10000 Travelling Column, Table Type CNC Milling Centre, with Automatic Oil Mist Lubricated Orthogonal Milling Head with 1 X 1 Degree Indexing and HEIDENHAIN TNC 430 M Control System. Year 2002 SN 8647 Table Area - 10000 x 1100 mm Column Traverse (X) - 8500 mm Vertical Traverse (Y) - 1600 mm Ram Traverse (Z) - 1200 mm Spindle Motor - 28 kW Spindle Taper - Standard ISO 50 BT50 tooling Pullstud - DIN 6987 2-Form A. ISO 7388/2-Form A Independent Gearbox with 2 Ranges Speed Range - 20 to 4000 RPM Feed Range - 5 to 5000 mm/min Rapid traverse rate - (X, Y, Z) 15,000 mm/min Preloaded double nuts and recirculating ballscrews to each axis. Linear Guiding System with recirculating cylindrical rollers and steel guideway assemblies in X, Y and Z axes Independent A.C Drive motor to each axis. Linear Transducer in X, Y and Z-axes with air purge system. Automatic tool clamping. Automatic hydraulic tool releasing device. CNC Control HEIDENHAIN TNC-430-M. (Flat TFT screen with digital drives) 9 axes CNC and 1 spindle, 5 of them simultaneously interpolated. Working area lighting Electrical cabinet cooling system Electrical cabinet lighting Heidenhain HR410 portable electronic handwheel with 3m spiral cable Horizontally articulated pendant for CNC control Orthogonal head 28KW, 800Nm, 1deg x 1 deg, 4000rpm oil lubricated Price includes oil cooling unit for both head and gearbox. Option G2, Ram prepared for 4000rpm, is also included. Coolant through the spindle type AD. Coolant system with 500l capacity tank with two pumps providing low and high pressure of 3 and 8 bars and 50l/min flow. The system includes a combined paper and magnetic drum-filtering unit. Standard operators platform fixed to the column 40 tools capacity toolchanger magazine, BT50 Max. Tool length = 400 mm. Max. Tool diameter: - With full magazine = 120 mm. With adjacent position empty = 250 mm. Ksdpfx Aeuv Hrdoh Usnf Max. Tool weight = 20 kg. Mean tool weight with full magazine = 10 kg. Max. Permitted total weight = 20 kg. Swarf Conveyor Hinge type conveyor belt Machine preparation for the addition of a 4th axis electro-mechanical table. Splash Guarding against swarf at the table front and both sides. Consists of four sliding front doors with a height from the floor of 2.100mm and a length of 1.700mm each one. Manually operated opening and closing with mechanical interlock. The doors can be opened for the full longitudinal traverse. The rear of the table is open. Protection in the back and both lateral sides of the machine column.

Condition: refurbished (used), Year of construction: 2025, functionality: fully functional, machine/vehicle number: 312560, Completely overhauled - new painting New workbench - new geometry Manufacturing origin Swiss Voltage 380V 50Hz 3Ph Customs position 8458.1930 Kedpfx Ahodr R Tco Uonf TECHNICAL DATA Capacities : - height of centres 102 mm - distance between centre, standard headstock type W 470 mm - distance between centres, headstock type W with reduction unit 375 mm - swing over bed 200 mm - swing over carriage 120 mm Bed : - height-width-length 168-100-1000 mm cast-iron bed with ground inverted-V profile Headstocks : - spindle nose for collets W-25 - maximum bore through collet 19.0 mm - headstock with reduction unit, ratio 1:5 Carriages : - stroke of longitudinal tool slide 90 mm - stroke of transverse tool slide 100 mm - size of tools 12x12 mm Tailstocks : - internal taper of tailstock spindle Morse 2 - spindle stroke, screw- and handwheel-operated 80 mm errors and omission excepted-data given without obligation Inventory Nr.2210049, machine equipped with : 1 Bed 105-11 1 headstock 105-26 1 cross carriage 102-45 1 tailstock 105-65 1 motor Voegtle 380V/50Hz/3ph. ; 750-3000 min-1. ; 0,4/0,9 kW 1 set of 40 collets W20, Ø 0,5 to 20 per 0,5 mm. 1 turret Tripan 111S 2 tool-holder Tripan 131 1 tool-holder Tripan 132 1 hollow center W20

Condition: excellent (used), Year of construction: 2015, - Travel X=3000 mm, Y=1500 mm, Z=1400 mm - Heidenhain iTNC 530 with handwheel HR 410 - NC rotary table for multi-sided machining 1600 mm x 1250 mm - 1-axis NC universal drilling and milling head, for simultaneous and positioning positioning operation (A-axis, 45°-axis) - Motor spindle 7,000 rpm max. SK 50, 530 Nm spindle torque - Tool changing system SK 50 / 40 places for 400 mm long tools tools - Chip screws in X-axis, optimum chip transport - Chip conveyor (hinged belt conveyor) for transverse conveying, Fabr. Knoll, front ejection - Coolant supply 950 l, made by Knoll - Outside/inside air at the spindle - IKZ 60 bar for deep hole machining - Operating mode 4 - Full enclosure with safety glass panes with sliding doors, optimized for crane loading - Split sliding doors on the front side - Split sliding doors on the operator side - RMP 60 radio measuring probe Knsdpfox Em Raox Ah Usf - incl. washing gun - Short delivery time by arrangement, subject to prior sale - Used machine - Z-axis KGT renewed in September 2023 incl. bearings - Optional fixators and tie rods - optional commissioning/installation - optional transportation

Condition: new, Year of construction: 2026, Brand new installation from one of the world’s largest manufacturers, Dardi International / Flying Bridge design, 3x2 m cutting area, 2-D, linear guides with ball screw drives on all three axes, Yaskawa motors with controllers. Delivery time approx. 6–8 weeks, available directly in our showroom in Elsenfeld, with the following equipment: Many machines of the same type can be inspected in advance in Benelux, Switzerland, Germany, etc. Please contact us. -- Other sizes available on request ---- Machine - 2x3m cutting area with stainless steel tank and wave-shaped replaceable steel supports - ESA PC control with WIN 11 - IGEMS 2-D CAD/CAM programming system including automatic nesting to minimize material waste - 1 cutting head, 2-D version - Handwheel - High-pressure supply via rotary union - Automatic central lubrication - High-pressure supply via profile stand and shut-off valve - Allfi® abrasive feed system 1.3 t fully automatic Knedpfxex Ig Sie Ah Uef - Allfi® abrasive metering system 2.0, stepless adjustment without pneumatics - KEYENCE light curtains for CE compliance - IGEMS and operator training as well as on-site installation available at extra cost Price ex works Elsenfeld. We are the European distributor for Dardi International with 26 years of experience in high-pressure waterjet systems. At extra cost: - High-pressure pump BFT Ecotron 40.37+ - Aqualon High Pressure Pump AQRO S50c 37 KW / 3.8 l/min Optional: Manual tilting head available at extra cost – see pictures.

Condition: new, Year of construction: 2025, travel distance X-axis: 1,200 mm, travel distance Y-axis: 640 mm, travel distance Z-axis: 620 mm, rapid traverse X-axis: 48,000 m/min, rapid traverse Y-axis: 48,000 m/min, rapid traverse Z-axis: 32,000 m/min, torque: 108 Nm, controller manufacturer: HEIDENHAIN, controller model: TNC 640, workpiece weight (max.): 800 kg, table width: 600 mm, table length: 1,400 mm, table load: 800 kg, rotational speed (max.): 12,000 rpm, overall weight: 9,000 kg, coolant supply: 20 bar, spindle nose: SK 40 BIG PLUS, number of slots in tool magazine: 30, tool length: 300 mm, tool diameter: 150 mm, tool weight: 8 g, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, SPECIAL CLEARANCE SALE AT DISCOUNTED PRICE BRAND NEW MACHINING CENTRE Control and motors: HEIDENHAIN TNC 640 digital path control HEIDENHAIN package (motors, measuring systems, handwheel) Additional equipment: Prepared for 4th axis (rotary table) Full enclosure with side folding inspection windows Accuracies: Knedpfx Aoxx S Tdsh Uof Positioning accuracy: ± 0.005 mm Repeatability: ± 0.003 mm This offer applies only to this LAGUN L1200 stock machine (interim sale reserved).

Condition: used, Surface Grinding Machine, Precision Surface Grinding Machine BRAND (Switzerland) Type Mini 500 machine no.: 505/86 year of construction 1986 Electro magnetic clamping plate 450 x 200 mm grinding length 500 mm grinding width 240 mm cross movement 220 mm table longitudinal movement 550 mm distance spindle center - magnet max. 350 mm grinding wheel diameter 225 mm grinding wheel width max. 25 mm grinding wheel bore 50,8 mm table longitudinal feed 0,5-24 m/min infinitely variable table cross feed pulse 0,05-30 mm cross feed 10 - 1000 mm/min. vertical infeed 0,001 - 0,05 mm vertical dividing feed 600 mm/min. Grinding wheel speed 2820 rpm. Grinding wheel speed 33 Vm/sec. motor power grinding spindle 2,2 kW Motor power hydraulics 1,1 kW mains connection 400 Volt, 50 Hz, 9,5 kVA - automatic depth infeed, vertical infeed - mechanical handwheels for axis movements - hydraulic longitudinal table movement - electromagnetic plate WAGNER 450 x 200 mm, height 73 mm - central lubrication - belt filter system with coolant tank and pump adjacent L x W x H = 1300 x 500 x 650 mm Knjdpfx Ahjd Nrqfj Uef - 2 pieces additional grinding wheel holders for grinding wheels with 50,8 mm inner diameter - 1 piece balancing shaft and 1 piece grinding wheel puller - hydraulic power pack L x W x H = 700 x 300 x 750 mm space requirement L x W x H 2000 x 1400 x 2250 mm weight approx. 1600 kg good condition

Condition: refurbished (used), Year of construction: 2025, functionality: fully functional, machine/vehicle number: 6360.16.65, Country of manufacture: Switzerland Voltage: 380/400/50/3 Net weight: 1350 kg Customs tariff number: 8460.1920 Dimensions: 200/120/160 cm TECHNICAL SPECIFICATIONS Maximum saddle travel: 530 x 220 mm Maximum grinding surface: 520 x 230 mm Table clamping surface: 600 x 200 mm Ksdpfjw Ucxqjx Ah Uenf Table speeds Longitudinal, standard operation: 0-25 m/min With slow feed: 5/10 mm - 8 m/min Cross feed: 0-6 m/min Vertical travel by hand: 330 mm Rapid travel by motor: 290 mm Rapid feed rate: 460 mm/min Max. distance between table and spindle axis: 412 mm Vertical feed movement Handwheel, 1 division: 0.01 mm Micrometric device, 1 division: 0.001 mm Automatic: 0.001-0.099 mm With pulse button: 0.001 mm Cross feed movement Handwheel, 1 division: 0.01 mm Micrometric device: 0.001 mm Grinding wheel Diameter x width x bore: 225x25x50/51 mm Standard RPM: 2700 rpm With variable speed drive: 3700-1300 rpm All technical data are provided without guarantee and are subject to possible errors or omissions.

Condition: reconditioned (used), Year of construction: 2010, • Traveling distances X=3100 mm, Y=1950 mm, Z=1390 mm • Heidenhain iTNC 530 with handwheel HR 410 • Machine table for multi side working 3000 mm x 1600 mm • 2-axis NC-universal milling head, for simultaneous and positioning working • Spindel 10.000 U/min HSK 100, 130 Nm Spindle torque • Tool change system HSK 100 / 40 places for 750 mm long tools • Chip conveyor (screw type) in X-axis, for transport into • Chip conveyor scraper belt type (traverse conveyor), Fabr. Knoll • Coolant container 900 l, Fabr. Knoll • Outside air at spindle • IKZ 60 bar for deep hole drilling function • Covering with safety glass pane, open at the top for loading by crane • 2 part sliding doors at the operator side • 2 part sliding doors at the front side, for easy loading • Radio-controlled measuring probe RMP 60 • incl. washing gun • incl. podiums at the front side and operator side • complete factory overhauled and painted new • short time delivery after arrangement • used machine • Y-axis ball screw in September 2021 incl. bearings renewed • X-axis new linear guiding system, July 2023 changed, renewed • Spindle overhauled at Mai 2023 (clamping system new, clamping cartridge new, rotation unit new, general tests) (at 23105 spindle hours)) • can be visited under power at 72793 Pfullingen • optional fixators • optional installation at customers plant • optional transport Kedpfxox Em N Ae Ah Usnf • 23122 spindle hours in total • 53991 machine hours in total • Year of construction 2010 Subject to prior sale

Condition: refurbished (used), Year of construction: 2025, functionality: fully functional, machine/vehicle number: 176308, Country of manufacture: Switzerland Voltage: 400 / 380 / 50 / 3 Net weight: approx. 350 kg Dimensions: 82x85x156 cm Installed power: max 2 kVA Customs classification: 8460.3930 TECHNICAL SPECIFICATIONS GRINDING WHEEL SPINDLE UNIT Spindle speed (both rotation directions): 2,500 / 3,500 / 5,000 / 7,100 rpm Grinding wheel motor power (2,800 rpm): 0.4 HP Vertical slide stroke (linear): 100 mm Micrometric stop adjustment travel: 25 mm Micrometric stop readout accuracy: 0.01 mm WORKPIECE SPINDLE UNIT Kodow T S Sqjpfx Ah Uonf Workpiece spindle speed (both directions, continuous): 100–900 rpm Motor power: 0.2 HP Indexing plate teeth count: 120 Angular vernier reading: 20' Collet type: W-20 Horizontal travel: 100 mm Rapid feed per handwheel turn: 2 mm Micrometric feed per handwheel turn: 0.1 mm Micrometric feed per scale division: 0.001 mm SPINDLE HEAD SWIVEL RANGE (a) Main direction: 165° Fixed ratchet increments: every 3° Increments with micrometric screw: every 2' (b) Grinding plane: approx. 15° Stop: at 0° Cross movement range: 80 mm Micrometer travel: 25 mm Reading precision: 0.01 mm Extraction motor power (2,800 rpm): 0.25 HP All technical specifications provided without guarantee and subject to possible errors or omissions.

Condition: good (used), Year of construction: 1998, operating hours: 6,000 h, functionality: fully functional, machine/vehicle number: 107.40.98.165, Year 1998 Heidenhain TNC 430 710x500x500 mm - 42000 RPM Netweight 5670 kg Dimensions 2794x2997x3035* mm TECHNICAL DATA Table Dimensions 1220 x 457 mm Admitted load 1575 kg T-grooves 14 mm Number of T-grooves 5 Travels Longitudinal X 1016 mm Transverse Y 508 mm Knsdpfx Aecl Rureh Uof Vertical Z 635 mm Workspindle Power of AC-motor, 2-stepped gears 11kW Speed range, continuous 10-7500 min-1 Spindle speed (option) 10'000 rpm Taper ISO40 Feeds drive Feed programmable axes X, Y & Z 0 – 7620 mm/min Rapid feed axes X, Y, Z 18,0 m/min Automatisation Tool changer 20 pos Tool changing time (for nearby posts) 5,0 sec. errors and omissions excepted-data given without obligation Inventory Nr.4112006, machine equipped with  : NC Heidenhain TNC430M Milling spindle 42’000 min-1, HSK 40 E 36 tool positions Electronical handwheel Tool measuring Renishaw TS27 Ethernet card Minimal quantities greasing Unilube Aspiration Lumestat Protection cabin Rotary table Air passage through rotary table Vacuum clamping (by external provider) Spray gun Chips conveyor

Condition: excellent (used), Year of construction: 2014, operating hours: 39,000 h, functionality: fully functional, machine/vehicle number: 3325, Model S-191FTL-PRM Ø 50 mm Axis travel Milling vertical axis Z = 200 mm Milling transverse axis Y = 200 mm Milling longitudinal axis X = 410 mm Power / Thrust Z-Y 2.5 kW / 550 daN X 4.5 kW / > 550 daN X-Y-Z Traversing speed: 40 m/min Acceleration: 10 m/s² Resolution X-Y-Z: 0.0001 mm Measuring system: glass scale MAIN SPINDLE C (Horizontal turning axis) Power: 15 kW Torque / peak: 22 / 28 Nm Measuring system: direct Resolution: 0.0001° Accuracy: 0.001° Bar capacity: Ø 32 mm (option 50 mm) Turning spindle speed: 72,000°/min Clamping force, turning: 4,900 N at 6 bar Knsdpow T Sl Dsfx Ah Usf B-AXIS SPINDLE INCLINATION (machining) Power: 4.3 kW Torque: 119 / 226 Nm Angular travel: -25° / +115° Measuring system: direct Resolution: 0.0001° Accuracy: 0.001° Rotational speed: 36,000°/min Locking torque: 200 Nm MACHINING SPINDLE Power: 8 kW Torque: S1 = 9.5 Nm / S6 = 11.5 Nm Max speed: 30,000 min-1 (option 40,000 min-1) Tool clamping force: 1,000 N Locking torque: mechanical locking with straight toothing Tool holder taper: HSK-40 (A or E) Through-spindle lubrication: 30 to 100 bar (optional) TOOL CHANGER Number of tools: 30 (option 60) Number of indexed tools: all Tool change time: 1.2 sec. Chip-to-chip time: 4.4 sec. Max tool diameter: Ø 40 mm (80 mm if adjacent station empty) Max tool length: 130 mm Max tool weight: 1.5 kg MISCELLANEOUS Installed power: 25 kVA Operating voltage: 3/N/PE/400V/230V 50 Hz Pneumatics: 6 bar (dry air) CNC CONTROL: Fanuc 31i Screen: 15'' color Keyboard: alphanumeric Control panel features: - 1 key switch for functions - 1 feedrate potentiometer 0–120% - 1 spindle speed potentiometer 50–120% - 1 quick-selection button for machine functions - 1 integrated electronic handwheel CNC Options - Data server with ATA Flash, 1GB memory capacity - J947 1 MB RAM memory - S677 TCPC (tool center point control for 5-axis machining) - S808 Al nano HPCC (Al high precision contour control II) - J930 tool tip radius compensation - J893 coordinate system rotation - J819 Helix (cylindrical) interpolation - J953 memory capacity for 1,000 programs - J828 tapping without compensation chuck - S615 insertion of radii and chamfers - J894 workpiece coordinate system - S993 part setup error - R522 inclined machining plane control with guidance Interfaces - Bumotec-specific programming to minimize collisions - Simplified tool management to prevent input errors - Tool management by threshold value, change according to part count or tool life - Automatic tool setting on machine for easier tool handling - Part counter and production management Y-AXIS (horizontal cross milling axis) Travel: 200 mm Power / thrust: 4.8 kW / 240 daN Resolution: 0.0001 mm Max travel, V1: 50 m/min Max travel, V2: 20 m/min Measuring system: glass scale Z-AXIS (horizontal longitudinal milling axis) Travel: 400 mm Resolution: 0.0001 mm Max travel, V1: 50 m/min Max travel, V2: 20 m/min Measuring system: glass scale Includes 8kW cooling unit Emergency braking system integrated Subject to errors and omissions, technical specifications are provided without obligation.

Condition: refurbished (used), Year of construction: 2025, functionality: fully functional, machine/vehicle number: 1845/455, Completely refurbished: Mechanics, geometry, hydraulics, and electrical components Wheelhead Disassembly, cleaning of parts, replacement of worn and defective components, motor overhaul, replacement of bearings, replacement of belts, spindle disassembly, replacement of seals and O-rings, plus adjustment. New paintwork. Workhead Disassembly, cleaning of parts, replacement of worn and defective components, motor replacement, replacement of belts. New spindle bearings. New paintwork. Tailstock Disassembly, cleaning of parts, replacement of worn and defective components, motor replacement, replacement of belts. New spindle bearings. New paintwork. Internal grinding attachment Disassembly, cleaning of parts, replacement of worn and defective components, installation of the support and geometry alignment. New paintwork. Hydraulics Disassembly, motor replacement, hose replacement, defective and worn parts replaced. Hydraulic block checked. X-Axis Disassembly, replacement of worn items such as O-rings, seals, rings, etc., overhaul of hydraulic piston, regrinding of tables. Z-Axis Disassembly, regrinding of tables, replacement of worn and defective parts, overhaul of hydraulic piston, scraping of V and flat guides. New paintwork. Measuring system Digital 2-axis display included. Electrical cabinet Replacement of motor contactors and relay controls. New wiring. New variable speed drive (frequency inverter) for the workhead. TECHNICAL SPECIFICATIONS Distance between centers: 1500 mm Distance between centers (workhead to tailstock overhang): 1650 mm Center height, standard: 125 mm Center height with riser blocks: 225/250 mm Maximum grinding diameter: Ø 250 mm Maximum grinding diameter with riser blocks: 450/500 mm Table Usable surface: 2060 x 140 mm Max. length and width for surface grinding: 1750 x 200 mm Longitudinal travel, manual or hydraulic: 1750 mm Manual table movement, 1 handwheel revolution – coarse: 20.006 mm Manual table movement, 1 handwheel revolution – fine: 2.457 mm Table speed, continuously via hydraulics: up to 6 m/min Table swivelling: 6° Stop and return: 0–5 sec. Workspindle Workpiece speeds, continuously variable (electric): 20–400 rpm Swivelling: 360° Workspindle taper (internal): MT5 Tailstock Internal taper, tailstock spindle: MT3 Spindle retraction, manual or hydraulic: 30 mm Diamond dresser taper (internal): MT0 Universal grinding head Cross slide travel for wheel: 285 mm Rapid traverse for wheel slide, front and rear: 40 mm Grinding spindle speeds: 1500 – 1700 – 2200 – 3600 rpm Vertical grinding spindle movement, center heights: 125–330 mm Max. wheel for cylindrical grinding: 400 x 50 x 127 mm Max. wheel for surface grinding: 250 x 20 x 76 mm Head swivelling with locking at every 90°: 270° Wheel feed 1 division of the micrometer drum: 0.005 mm/Ø Automatic wheel feed, max.: 0.9 mm/Ø Motors Grinding spindle motor: 2,900 rpm / 4.0 hp Workspindle motor: 3,000 rpm / 2.0 hp Coolant pump motor: 2,850 rpm / 0.12 hp Internal grinding attachment Bore: 70 mm Knodpfx Ajxt Ilfeh Uef Internal grinding spindle speed Ø70 mm: 14,000 rpm Internal grinding spindle speed Ø50 mm: 21,000 rpm Subject to error or omission, the technical information is provided without obligation.