Used Powder Painting for sale (4,280)

Condition: new, Year of construction: 2024, functionality: fully functional, Price for the purchase of a powder coating system - Negotiable !!! - Electrical data 100-240V 50-60Hz - Powder absorption up to 200g / min - Air consumption up to 250L / min at 6 bar - Air quality / vapor less than 1.3 g / nm3 - Air quality / oil less than 0.1 mg / nm3 Powder coating gun data - Output voltage 100 kV - max. output current 100 µA - Length of hose 6 m - antistatic hose - Polarization Negative - Conformity ATEX 2mJ Description of hose - Applicator for quick color changes directly from the box - Intuitive 7" touch display - Automatic cleaning function - gun rinsing - Up to 20 user-defined programs - 3 automatic programs - Remote control of the paint quantity and program change from the handpiece -- Equipment - Controller of the PSS series - ProfiJector RI-1 blunt powder injector - ProfiGun powder gun with quick coupling and remote control - One set of hoses - Stand with vibrator and suction unit with fluidization PSS driver - 7-inch touch panel that can be operated with a glove - 3 automatic programs (overpainting, hard-to-reach surfaces, flat surfaces) - Graduation in 0.1kV and 0.1uA steps - Advanced pneumatic valves for air dose control (romer - patent pending) - The actual air flow measurement reacts to errors such as pressure loss or blockage of the system - Advanced diagnostic tools - Ability to name programs - Ability to control external master controllers with ModBus protocol (A-Series) ProfiGun PM-1 gun - A lightweight ergonomic gun, perfectly balanced with a contoured handle - The ceramic cascade with a voltage of up to 100,000V efficiently loads all types of powders - The new generation of nozzles ensures perfect powder penetration into complex shapes - The profiled nut provides a good grip - The conductive handle with high carbon content provides excellent grounding for the painter - The spray gun is made of special materials with increased impact resistance - Fully demountable design with replaceable powder path tube - The spray gun is patented in the USA and the EU - Cascade polarity - negative ProfiJector powder coating pump Nsdsg U I Ugjpfx Adtjcr Description of the pump - Design of a new efficient injector - The most effective feed angle proven by research - Saves paint and air compared to right angle injectors - It is characterized by relatively low operating costs compared to other pumps - The injector is covered by a European patent

Condition: good (used), Year of construction: 1994, Technical data: - Manufacturer: Heesemann Bdjdmayow Dplws Tmbeh - Type: EA4 - Year of construction: 2002 - Working width: 1,300mm - Working height: 880-920mm - Scooter transport, rubberized rollers - Roll pitch: 65mm - Roll diameter: 60mm - Fine dust filter Arrangement of the dust removal modules seen in the direction of flow: 1) Air blowing channel 1 piece from below 2) Ionization from below 3) Air blowing channel 2 pieces from above Ncedpfx Adjxiy Htstor (With its own fan, no compressed air required) 4) Ionization bar from below and from above Installation dimensions: - Installation length: 830mm - Width: 2.245mm - Height: 1,470mm - Suction nozzle: D 160mm - Height adjustment: motorized - Seperat control panel with hight adjustment included ( see pictures )

Condition: like new (used), Year of construction: 2022, functionality: fully functional, complete plat concisting of: Ncjdpfx Adexw Ux Hetjr Bi-rail overhanging conveyor with two points bar support , lift and rotation unit Spray booth for robot with full recirculation, with autimatic pre-filter replacment system High pressure humidificer for spray booth and flash off room Robotic spray system for windows with jacket nozzle cleaning unit automatic color change (3 independent ) electrostatic safty system paint flow meter drying tunnel with ldp system and axial fans supervisor systeem with data interface and datamic reader “The line is packed for transport. It has been previously installed, but it has never been taken into operation.”

Condition: used, Used paint mist extractor Nedpfxowka Nao Adtscr with 2 side baffles with 2 fans otherwise as shown in pictures Availability: Short term Storage location: Röllbach

Condition: new, Year of construction: 2026, functionality: fully functional, working height: 2,200 mm, BUMEX Sp. z o.o. offers a professional industrial washing system designed for the preparation of components prior to the powder coating process. The equipment has been engineered for demanding industrial environments where washing efficiency, process stability, and long-term durability are essential. The washing system enables effective preparation of steel and aluminum components through a multi-stage cleaning, degreasing and rinsing process. Technical parameters Working chamber dimensions: 1500 × 3200 × 2200 mm Process technology: 3-stage washing process Process tanks The unit is equipped with three process tanks: tank for cleaning / degreasing chemicals tank for rinsing water tank for demineralized water (DEMI water) Tank capacity: 1500 – 2000 liters DEMI water generator The system is equipped with a demineralized water generator, ensuring high-quality final rinsing and optimal surface preparation before powder coating. Heating system The chemical tank is equipped with a heating system for the process liquid. Available heating options: oil heating gas heating electric heating Maximum operating temperature: up to 60°C Machine construction The machine is manufactured entirely from high-quality stainless steel AISI 1.4301, which provides: excellent chemical resistance long service life easy maintenance and cleaning The washer features: very robust industrial construction full thermal insulation of the entire machine to reduce energy losses spray system designed for minimal mixing of process liquids Njdpfx Adehfv D Sjtecr pre-filter for collecting contaminants high washing efficiency Control system The machine is equipped with a fully automatic control system, enabling precise control of: process temperature pump operation washing time sequence of process stages Why choose BUMEX? Our equipment stands out on the market due to: very high manufacturing quality robust industrial construction operational safety complete technical documentation possibility of adapting the equipment to the existing production facility All machines manufactured by BUMEX Sp. z o.o. are CE certified. Additional technological support BUMEX also provides: powder coating booths dust extraction and filtration systems industrial ventilation systems professional technological consulting Cooperation conditions company transport available (price determined individually) VAT invoices issued short production lead times possibility of manufacturing machines in custom configurations and dimensions

Condition: excellent (used), AZZURRA CS4B Spray Booth Wall Length: 4000 mm 2x cardboard filters Pint Stop filters Filtration capacity ~ 15,000 m3/h Motor power: 4.0 kW CE marking Ncedpjyh E Hnefx Adtsr

Condition: used, Year of construction: 2011, Powder coating line AABO Andersen Nedpfx Aeyrnh Eodtjcr

Condition: excellent (used), Year of construction: 2015, Brand: Makor Type: Robospray Twin Year: 2015 Inner dimension L: 670 cm Inner dimension W: 330 cm Inner dimension H: 213 cm Exhaust system: Yes Electric connection: 400 V Dimension L: 11000 mm Dimension W: 4600 mm Dimension H: 4500 mm Includes - 2x electric foil roll-off units; - 1x Beerepoot mobile roller conveyor Ncjdpfjiu Hbnox Adtjr

Condition: good (used), Year of construction: 2001, functionality: unexamined, machine/vehicle number: 212018, NESTRO Paint Mist Extraction Unit Model NFW 2015 Used Machine Serial No.: 212018 Year of manufacture: 2001 Article number: JA_G260201 Description: Working area (L/W): 2000 x 1500 mm Airflow: 7000 m3/h Pressure: 450 Pa Power supply: 380V / 50 Hz 2.2 kW Exhaust duct diameter: 350 mm Footprint (W x D x H): 3000 x 800 x 1600 mm Weight approx.: 360 kg Ncsdpfsygv D Dex Adtsr Condition / Performed work: - Item cleaned - Item functionally tested - Age and usage-related signs of wear - Available ex stock Note on used equipment: • Prices are ex works (unless otherwise specified!) from our location in Ottendorf-Okrilla, Germany – loaded free of charge! (unless otherwise specified) • Subject to prior sale! • You will receive an invoice showing VAT. • All items are sold as inspected, with no warranty or guarantee claims of any kind. Prospective buyers are welcome to inspect the items at our premises. • Our general terms and conditions apply. • Special agreements are only valid in written form. • Any items shown in the background of pictures are not included in the scope of delivery. • Saw blades are for illustration purposes only and not included in the sale. Shipping options: • We are happy to provide you with a transport quote. • Collection from our location in Ottendorf-Okrilla is possible by arrangement and free of charge. (Assembly and operational instruction for demonstration purposes available upon request and subject to agreement!) • Delivery may be partially disassembled. • Optionally, our trained service personnel can assemble the machine at your site and provide a brief introduction. Travel, transport, and service times subject to additional charge.

Year of construction: 1994, condition: good (used), Working area approx. 2-080 x 1,430 mm, lateral baffles right and left, Filter area approx. 1,800 x 1,300 mm, 2 rows of paper volume filters approx. 650 x 1,800 mm inside fine filter G4 approx. 1.350 x 2.000 mm, air capacity 4.500 m³/h, pressure max. 500 Pa, Nsdpfx Ajpvil Tsdtocr motor 1,1 kW / 1.400 rpm.

Condition: ready for operation (used), machine/vehicle number: 89915, Drive = compressed air, Material/air ratio = 16:1, Material pressure max. 90 bar, Air inlet pressure 1 to 6 bar, 4 double strokes for 1 liter of material, with gun type MX with double hose, unused since last service 01/20, condition as seen, ex stock Seevetal, subject to prior sale Ncodsiv Huwjpfx Adtsr

Condition: ready for operation (used), Year of construction: 2006, working width: 150 mm, overall weight: 150 kg, Conveyor Belt 2500 mm Manufacturer: Makor Type: TEP 2500 Powered conveyor belt from a finishing line (positioned in front of a Makor profile spraying machine), Length approx. 2500 mm Belt width: 150 mm Pass-through width (with existing side guides): max. approx. 320 mm Nedpfsxtnfrjx Adtscr Feed speed steplessly adjustable via variator Equipped with stable, adjustable side guides Dimensions approx. 2500 x 550 mm (LxW) Weight approx. 150 kg Documentation available

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 3,500 mm, total length: 7,050 mm, total width: 4,100 mm, volume flow: 36,000 m³/h, temperature: 80 °C, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), Equipment: cabin, lighting, Paint and Drying Booth It is the centerpiece of your entire painting operation: the combined paint and drying booth. (Alternatively available as a separate paint booth with a dedicated dryer.) Our solutions feature full-surface ceiling filters and, optionally, full-surface floor extraction with drive-over grating or wall extraction at the position of your choice. If you wish to further increase the efficiency of the system beyond heat recovery and infinitely variable control via frequency converter, we can also offer you a sectional control system. This enables you, for example when doing spot repairs or partial booth loading (such as painting only add-on parts), to activate only the section where the parts are located. This allows you to operate with a reduced air volume, save energy, and minimize costs, all without compromising quality. Feel free to contact us – we would be happy to demonstrate these options in detail. Nedoxa H Ewspfx Adtecr Do you have any questions or suggestions? We are happy to assist you.

Condition: new, Year of construction: 2025, total height: 4,000 mm, total length: 7,000 mm, total width: 3,000 mm, warranty duration: 24 months, temperature: 80 °C, air demand: 36,000 m³/h, input voltage: 380 V, heating capacity: 345 kW (469.07 HP), power: 40 kW (54.38 HP), fuel: liquid petroleum gas (LPG), energy consumption: 40 kWh, insulation material: Mineralwolle, insulation thickness: 50 mm, nominal power: 345 kW (469.07 HP), Equipment: lighting, MAIN STANDARD Our paint booths are designed to meet all necessary requirements for paint application, including air filtration, extraction, lighting, and a controlled environment. Booth processes are managed via a PLC system, ensuring that desired values are maintained consistently. OPERATING PRINCIPLES OF THE BOOTH The booth’s processes are managed through a control panel, which oversees the following steps: PAINTING PROCESS During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled through the extraction unit. Floor filters (paint stop filters) collect paint particles, and the air passes through final exhaust filters before being discharged. Ncsdpfxowzmcbo Adtsr FLASH-OFF PROCESS After painting, the booth continues operating for approximately 15 minutes to purge residual solvents and thinners. During this phase, fresh air circulates from outside into the booth. DRYING PROCESS In this stage, 80% of the air passing through the booth is heated to 60°C and introduced via a distribution system. Since 20% of the solvent is released during drying, it is expelled with the exhaust air. Industrial coatings are typically dried at 60°C, but the booth temperature can be adjusted as needed via the control panel. COOLING PROCESS After the 30-minute drying cycle, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the subsequent 5-minute cooling phase, fresh air from outside circulates through the booth, after which the system shuts down automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT These control panels govern the functions and operation of machines and devices housed within the booth. The panel is made of durable galvanized sheet and steel profiles and is fully enclosed to protect against dust and moisture. Electrical Equipment and Control Panel: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control connections between the control panel and motors or other electrical devices. • Electrical wiring is designed to accommodate booth relocation if needed. • Operating equipment uses 380 V 50 Hz, while control devices operate at 220 V. • The booth’s operation time can be monitored on the electronic control panel, enabling straightforward maintenance scheduling. • Temperature and time settings for booth ventilation (solvent flash-off), intermediate drying, and final drying can be easily adjusted to required values on the digital display of the electronic control panel. • Users can monitor and adjust the drying time using the heating thermostat and time relay.

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. Ncsdpfx Adswzl Hxstor * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: PEF-2.5 PULVER EINBRENNOFEN ELEKTRISCH, temperature: 230 °C, heating capacity: 30 kW (40.79 HP), inner dimension length: 2,500 mm, inner dimension width: 1,505 mm, ✈️ Plus shipping costs – Shipping available upon request.✈️ Fast delivery: Only 6 weeks after receipt of payment! ✅✅✅Energy Class A+++✅✅✅ ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✳️ Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today to learn more about our hire purchase, warranty, or leasing programs. ☘️Environmentally friendly☘️⚡️Green energy⚡️☘️ ⭐ Powder furnace with electric heating - ✔️ Internal dimensions: 2500 mm L * 1505 mm W * 1800 mm H ✔️ Electric heating output: 30 kW/h ✔️ Fan: 3000 m3/h 80 mm SS ✔️ Circulation fan output: 1.5 kW/h ✔️ Total 35 kW/h +- 10% ✔️ Digital heat control, continuously adjustable temperature up to 220°C ✔️ Sandwich panels inside: 1.5 mm galvanized steel, outside: 1.5 mm powder-coated Steel ✔️ Adjustable curing temperature, curing time, and exhaust fan function ✔️ An audible signal sounds at the end of the curing time ✔️ Insulated door with special locking systems (snap lock) ✔️ Insulation: 150 mm (150 mm rock wool) 🔥 PEF-2.5 Curing Oven: Your versatile industrial oven for drying and curing processes! 🔥 Whether powder coating, wet paint, plastic processing, or other thermal processes – the powder curing oven is your reliable solution for professional curing and drying processes up to 230°C! 🌡️ _____ 🚚 Maximum loading flexibility • Compatible with ceiling rail systems • Optionally with insert shelf system for small batches _____ ⚙️ Intelligent control – just the way you need it ✅ PID control (optional) for precise temperature control ✅ Touchscreen control panel & smartphone control 📱 (optional) ✅ Weekly & monthly reports at the touch of a button (optional) ✅ Timer function: freely programmable from 10 minutes to 24 hours ⏲️ ✅ Automatic shutdown after the end of the process _____ ♨️ Ramp heating mode (optional) Precisely control temperature progression and holding times, e.g. E.g.: • Reach target temperature within a defined time Ncsdpfxjwfgbrj Adter • Maintain desired time • Controlled cooling to target temperature • Automatic notifications of process events _____ 🛡️ Safety is our priority 🟢 Safety sensors to prevent overheating 🟢 Automatic shutdown in the event of a fault 🟢 Acoustic warning signals in the event of errors 🟢 Solvent and fume removal via automatic venting _____ ⚡ Customized energy and heating system 🔥 Also available with an extension up to 400°C for high-temperature processes (optional) _____ 🧠 No repeated settings necessary! The furnace saves your process parameters – batch by batch. This saves you time and avoids errors. _____ 📢 And best of all: If you have special requirements – we also build customized furnaces according to your specifications! Contact our team of experts for a personalized consultation! _____ ☀️ 2-YEAR WARRANTY ☀️ Request more information

Year of construction: 2003, condition: excellent (used), Powder compacting automatic press DORST DACS15 Yom: 2003 Nedpfeggrw Rex Adtecr Mechanical high-efficiency automatic press Pressing force: max. 150kN Ejection force: 50kN Die support in pressing position: max. 150kN Return force of lower punch: max. 32kN Closing force of upper punch: max. 12kN Upper punch stroke: 90mm Upper punch adjusting travel: 60mm Stroke rate: 8...40strokes/min

Condition: good (used), Year of construction: 2012, I. System Concept of the New Painting Workshop Based on Drawing: 12-137-010a System Description: The system is designed for painting parts of IKEA garden furniture. Dimensions of individual parts: - Length: max. 3,500 mm - Width: max. 100 mm - Height: max. 2,200 mm Part Hanging Arrangement: - 2 chairs/1 table (220 per beam, stacked one above the other); paint application must be adjusted to prevent dripping onto the parts. Traverse (Beam) Length: - 4,000 mm Number of Traverses: - 228 pcs Nsdpfoylhxqjx Adtocr Conveyor Speed: - 5 m/min Capacity: - The system is designed to paint 300,000 pieces of garden chairs per year, calculated as follows: - 7,200 single parts per 2 shifts (one chair consists of 6 single parts) - 1,200 chairs per 2 shifts = 600 beams in 2 shifts - 600 beams x 1.2 min = 720 min = 12 hours effective production > 16 hours (2 shifts) – calculated based on 6 production hours per shift Paint System: - Intended for use with low-solvent (VOC-compliant), water-based paint materials from the respective manufacturer; non-combustible and non-reactive with other paint substances. - Coating process includes one cycle for both flow-coating and top-coating.

Condition: new, Year of construction: 2025, TPO0909E powder coating oven Nodpfxefgnytj Adtocr Working dimensions (mm): 900 (W) x 900 (D) x 1600 (H) SPECIFICATION: * Power consumption: 9 kW. Equipment: * Rod for hanging details * Convection (Equal temperatures throughout the oven), * Locks for safe opening and closing, * Maximum operating temperature: 230°C. TQ0906 powder coating booth Working dimensions (mm): 900 (W) x 600 (D) x 1400 (H) SPECIFICATION: * Power consumption: 1,6kW * Air capacity: 3200m3/h, * Hermetic lamp: 1pcs. * Automatic filter cleaning system * The cabin is equipped with a set of pneumatic quick connectors * Cartridge filter: 1 pcs * Paint recovery container Oven, cabin in stock, ready for shipment. CHOOSE BUMEX SP. Z O.O. Very high quality of the machines offered on the market. Professional advice and service. Warranty. Warranty and post-warranty service. Full technical documentation. 100% satisfaction of our clients. All products of the brand BUMEX SP. Z O.O. have WE certificate. We offer our own transport - prices are agreed each time for a given offer. We issue VAT invoices. Short lead times! Possibility to order machines in various, personalized configurations and dimensions. Please do not hesitate to contact us.

Condition: new, Year of construction: 2025, The BUMEX SP. Z O.O.company presents a powder coating booth. working dimension: 4500x2300mm 6 x polyester filter Automatic filter cleaning with adjustable range from 10-1200 sec. 2 x fan 2.2 kW, 10,500 m³/h (Total 21,000 m³/h) 2 x LED lamp Delivery time 14-21 days Our cabins are characterized by a very high quality of workmanship, safety of use and selection of cabin parameters to the existing building. We advise on the selection of paint booths, dust extraction systems, exhaust systems and industrial recuperation. CHOOSEBUMEX SP. Z O.O. Very high quality of machines offered on the market. Professional advice and service. Guarantee. Warranty and post-warranty service. Full technical documentation. 100% satisfaction of our customers. All BUMEX SP. Z O.O. are WE certified. mdvncpiz We offer our own transport - prices are set each time for a given offer. We issue VAT invoices. Ncsdpfx Aod S N Scjdter e.g Short lead times! Possibility to order machines in various, personalized configurations and dimensions! Feel free to contact us.

Condition: new, Year of construction: 2025, FILTER WITH A MEMBRANE PUMP !!! A bathtub for removing the varnish coat from rims and other objects covered with various types of paints, solvent varnishes and powder varnishes. Nodsgwg Haspfx Adtscr Basket working dimensions (mm): 1250 x 800 x 700 mm * The bathtub is made of high-grade 304 acid-resistant steel. * Insulated on all sides with 40 mm insulation material, it allows us to efficiently and quickly heat the liquid to the desired temperature. * The shell of the device is made of stainless steel. Equipment of the device: - Indirect heating (heating mantle), - Automatic temperature control of the heating medium, - Baskets made entirely of stainless steel, - LED indicator lights, - Ceramic heaters in the cover of 2 x 4,5 kW acid-resistant pipes, - Aeration system for the entire bottom of the bathtub, - 12-month warranty. Our devices are made with great care and attention to detail. CHOOSE BUMEX SP. Z O.O. Very high quality of the machines offered on the market. Professional advice and service. Guarantee. Warranty and post-warranty service. Full technical documentation. 100% satisfaction of our clients. All products of the brand BUMEX SP. Z O.O. have WE certificate. We offer our own transport - prices are agreed each time for a given offer. We issue VAT invoices. Short lead times! Possibility to order machines in various, personalized configurations and dimensions! Please do not hesitate to contact us.

Condition: excellent (used), Year of construction: 2000, WIWA high-pressure pump 235.42R / 38042, year 2000 With high delivery capacity, ideal as a feed pump for airless sprayers (suitable for medium and low viscosity coating materials) Material guide in stainless steel (suitable for water-based paints) Transmission ratio: 42:1 Air inlet pressure max. 8 bar Flow rate per double stroke 235 cm3 Delivery rate max. 38 l/min. Maximum permissible operating pressure 335 bar Piston diameter of the air motor 230 mm Piston stroke of the air motor 120 mm The devices are very little used! Technically and visually in very good condition. Ncedpfsthcflsx Adter ATTENTION: the price of EUR 1.900,- (net) is for 1 device !!!

Condition: excellent (used), Year of construction: 1988, functionality: fully functional, Connected load 4kW 1 pc. switch cabinet Nedoiau Tzepfx Adtjcr pipe connection 350 mm length 2000 mm, width 700 mm, height 1950 mm lateral baffles 1 pc. suction pipe D= 350 mm 3900 mm long 1 pc. bend 90° 350 mm 1 pc. Elbow 45° 350 mm deflector hood 350 mm Circuit diagram, operating instructions Return air system Air capacity max. 6500 m³/h motor power 2 kW with heat exchanger 1" water connection LxWxH 2150x820x820 mm 2 pcs. return air duct 2000x950x400 mm 1 pcs. return air duct 950x950x400 mm external wall connection 700x700 mm bird grille 660x590 mm heat exchanger outlet 400x400 mm Unfortunately, we cannot answer inquiries without complete contact information.

Condition: good (used), Year of construction: 2016, total height: 2,640 mm, total length: 3,300 mm, total width: 3,960 mm, volume flow: 8 m³/h, Equipment: cabin, Technical Details: 75 m³ area including paint booth, drying booth, and paint storage room. Paint booth: - Internal dimensions: 3300 x 3960 x 2640 mm - Floor area: 13.1 m² - Internal volume: 34.5 m³ - Heating method: air intake from the air-conditioned area Nedoyhbggopfx Adtocr - Air supply: 8,000 m³/h Drying booth: - Internal dimensions: 3300 x 3960 x 2640 mm - Floor area: 13.1 m² - Internal volume: 34.5 m³ - Heating method: electric heating cartridges, 22 kW, 3x400V - Air supply: 2,500 m³/h Paint storage room: - Internal dimensions: 3100 x 2000 x 2600 mm - Heating method: air intake from the air-conditioned area - Floor area: 6.2 m²

Condition: good (used), Year of construction: 1990, functionality: fully functional, For sale is a complete, fully operational powder coating system, year of manufacture 1990. Over the past few years, numerous system components have been modernized or completely replaced and upgraded. The system was decommissioned in Q1-2025, but can be reactivated and operated at any time if required. All components remain on standby and can be started up and demonstrated on site. The system features one manual and two automatic spray booths (which can be operated simultaneously). The maximum workpiece dimensions that can be coated across all booths are 7000x2300x800 mm. The entire conveyor system is supplied by CSF. All system controls, including a visualization system, all control cabinets, all frequency inverters, as well as many other components have been completely renewed within the last 5–7 years. There is no maintenance backlog; the system has been regularly and meticulously serviced by our own maintenance department and the respective manufacturers. A detailed description can be provided upon request. Price on request! Ncjdjw Ek Ntepfx Adtor