Used Tray Shelf for sale (8,176)

Condition: like new (used), Year of construction: 2025, Used cantilever racking: Screw system in hot-dip galvanized design Ljdpfxsfdkb Ts Afpehg Scope of delivery: 4 shelf uprights Height 4,160 mm with base section 1,200 mm usable depth 12 cantilever arms with 1,200 mm usable depth, standard Longitudinal and diagonal braces for 4,000 mm shelf length (spacing 1,300 mm) Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 90 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 4,160 mm - Load capacity per upright 2,250 kg - Base section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2025, Cantilever racking with roof supports: Hot-dip galvanized bolt-together system Scope of delivery: 9 rack uprights, height 4,230 mm, with base plate, usable depth 1,200 mm 27 cantilever arms, usable depth 1,200 mm, with deflectors 9 roof supports with 1,500 mm cantilever, pre-drilled for on-site roof construction (*Without wood purlins and trapezoidal sheets for roof assembly) Including longitudinal and diagonal braces for 1,500 mm upright spacing Incl. fastening material (without floor anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Spare parts reordering and extensions possible at any time) - (*Offer available in larger quantities: approx. 50 uprights in stock) Detailed description: - Robust steel construction made from IPE sections - All components with hot-dip galvanized finish - Load capacity per upright 2,700 kg plus roof, wind, and snow loads (Maximum snow load 1.85 kN/m² and wind load zone 2) - Load capacity per cantilever arm 900 kg - Including roof supports (Maximum snow load 1.85 kN/m² and wind load zone 2) - Cantilever arms height-adjustable in 100 mm increments - 3 bolt-on cantilever arms per upright, depth 1,200 mm with deflector = 4 storage levels vertically - Including longitudinal and diagonal bracing with 1,500 mm upright spacing - Rack length: 12,100 mm - Including fastening material (without floor anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Professional telephone consultation - Made in Germany - Short delivery times Lodpfoh R Taqex Afpshg - On-site pickup possible Our cantilever racks are exclusively produced in Germany. We offer reliable transport with prior notification before delivery. The goods are packaged for easy unloading. The installation surface must be concrete, level, suitable for anchoring, and capable of supporting the applied loads. The floor condition, load-bearing capacity, and any required official permits must be checked and ensured by the customer. The uprights must be anchored to the floor on site; wall anchoring is not required and not recommended. According to occupational safety regulations, it is recommended that the uprights have at least a 500 mm overhang above the top storage level.

Condition: as good as new (ex-display), Year of construction: 2024, Cantilever rack in painted version (RAL 7016 anthracite): Scope of delivery: 4 shelf uprights height 4,200 mm with base section 1,200 mm usable depth 12 cantilever arms with 1,200 mm usable depth Longitudinal and diagonal braces for 1,300 mm upright center distance (4,000 mm shelf length) Fastening material (screws, nuts and washers) Lhedomhhypepfx Afpeg - (*Delivery or collection in approx. 1 - 2 weeks) - (*No damage to paintwork!) - (*No damaged components!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Net price: € 1,990.00 plus VAT. Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Surface painted in RAL 7016 (anthracite) - Shelf height 4,200 mm - Load capacity per upright 2,200 kg - Foot section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 740 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. Delivery can be made in approx. 1 - 2 weeks after receipt of order. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The surface must be concrete, level and suitable for dowels and must be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any necessary official approvals are in place. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 3,500 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Lodpfx Aemhh Dhefpohg Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 3,500 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm usable depth Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 2,600 mm with foot section, 1,000 mm usable depth 12 cantilevers with 1,000 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 2,600 mm - Load capacity per upright 1,800 kg - Foot section and cantilever arms with 1,000 mm usable depth Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. Lhedpfxsmhh Dzo Afpeg The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 3,000 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) Lodpomhh Ansfx Afpshg - Hot-dip galvanized surface - Shelf height 3,000 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm usable depth Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: as good as new (ex-display), Year of construction: 2024, Cantilever rack in painted version (RAL 7016 anthracite): Scope of delivery: 4 shelf uprights height 2.56 m with base section 1.0 m usable depth (1.2 m total depth) 12 cantilever arms with 1.0 m usable depth Longitudinal and diagonal braces for 4 m shelf length (spacing 1.3 m) Fastening material (screws, nuts and washers) (*No paint damage!) Net price on collection: € 1,490.00 plus VAT. Delivery possible for an additional charge Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Surface painted in RAL 7016 (anthracite) - Shelf height 2,560 mm - Load capacity per upright 1,800 kg Lsdpfx Aoguk A Hsfpshg - Foot section and cantilever arms with 1,000 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. The substrate must be made of concrete, be level and suitable for dowels and be able to bear the acting loads. The customer is responsible for checking and ensuring the ground conditions and load-bearing capacity as well as any official approvals required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2024, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 rack stands, height 3,000 mm with base section 1,200 mm 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Rack height 3,000 mm Lhedpfx Afeguk Dkjpsg - Load capacity per stand 2,250 kg - Base section and cantilevers with 1,200 mm usable depth - Cantilevers in 100 mm increments height adjustable - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Cantilever rack with roof supports: Hot-dip galvanized bolted system Scope of delivery: - 9 rack uprights, height 4,230 mm with base section, usable depth 1,200 mm - 27 cantilever arms, 1,200 mm usable depth, with guards - 9 roof supports with 1,500 mm cantilever, pre-drilled for on-site roof construction (*Excluding timber purlins and trapezoidal metal sheets for the roof structure) - Includes longitudinal and diagonal braces for 1,500 mm upright spacing - Incl. mounting hardware (excluding floor anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Spare parts and extensions available to order at any time) - (*Offer available in larger quantities: approx. 50 uprights in stock) Detailed description: - Robust steel construction made from IPE profiles - All components hot-dip galvanized - Load capacity per upright: 2,700 kg plus additional roof, wind, and snow load (Maximum snow load 1.85 kN/m² and wind load zone 2) - Load capacity per cantilever arm: 900 kg - Including roof supports (Maximum snow load 1.85 kN/m² and wind load zone 2) - Cantilever arms height adjustable in 100 mm increments - Per upright: 3 bolted cantilever arms, depth 1,200 mm, with guards = 4 storage levels - Including longitudinal and diagonal braces with 1,500 mm upright spacing - Rack length: 12,100 mm - Including mounting hardware (without floor anchors) - With assembly instructions and C4 load labels according to DIN standard - Specialist telephone consultation - Made in Germany - Short delivery times - On-site pickup possible Lhsdpemhhy Nsfx Afpsg Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight services with advance notice before delivery. The material is thoughtfully packaged to facilitate easy unloading. The substructure must be concrete, level, and suitable for dowel anchoring, and capable of bearing the applied loads. The floor condition and load-bearing capacity, as well as any required official permits, must be checked and ensured by the customer. The rack uprights must be anchored to the floor on site. Anchoring to the wall is neither required nor recommended. According to Occupational Safety regulations, it is recommended that the uprights have at least 500 mm overhang above the top storage level.

Condition: like new (used), Year of construction: 2025, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 4,160 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Longitudinal and diagonal struts for 4,000 mm shelf length (distance 1,300 mm) Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 90 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Surface hot-dip galvanized Lsdpfomhh Dtsx Afpehg - Shelf height 4,160 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm Usable depth - Cantilever arms height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is packed sensibly to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and suitable for dowels and must be able to absorb the loads. The customer must check and ensure that the floor conditions and load-bearing capacity, as well as any official permits that may be required, are obtained. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and is not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 rack stands, height 2,600 mm with base section 1,000 mm 12 cantilevers with 1,000 mm depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 90 stands in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Rack height 2,600 mm - Load capacity per stand 1,800 kg - Base section and cantilevers with 1,000 mm usable depth - Cantilevers in 100 mm increments height adjustable - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Lsdpfxoguk Dve Afpshg Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is packed sensibly to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: used, functionality: fully functional, Shelf trolley / Transport trolley / Order picking trolley / up to 7 levels / 3 mesh walls / 3 shelves Lhedpfxeyw Nthe Afpeg

Condition: good (used), Stacking boxes, plastic boxes, Euro stacking boxes, transport baskets, stacking baskets, Euro stacking containers, small load carriers, storage bins, shelf boxes, shelf boxes -Manufacturer: Schoeller, Arca Systems shelving units -Type: 9133 -Number: 1190 boxes available -Price: per piece, minimum order 5 pieces Lodpeuzn Dxofx Afpshg -Dimensions: 595/230/H100 mm -Weight: 0.7 kg/pc.

Year of construction: 2019, condition: like new (used), Thermoformer Designed for pharmaceutical environments, it can thermoform trays for vials, ampoules, syringes, and medical devices in general, using thermoformable films such as PVC, PET, R-PET, Polystyrene (PS), PP, PLA, etc. Possibility to cold-form Aluminium based materials. Main Features: Balcony structure for easy access and cleaning High-speed positive automatic product feeding systems Available with or without a sealing station Arrangeble for in-line connection Quick, repeatable, and tool-free format change Lhjdeybcwtopfx Afpjg Thanks to the servo-assisted main transmission, the machine speed is adjustable from the main HMI within dedicated recipes Automated thermoformer machine. Forming material reel unwinding - preheating - forming - filling with laminated strips (robot) - applying and sealing tyvek lid - cooling - serialised printing - indexing - punching - feed sealed strips out to box packaging machine.

Condition: good (used), JBT Proseal high throughput tray sealing line. Complete with a set of tooling and tool carrier. Rarely available. Lhodpfx Afjwmc Azspog

Condition: good (used), We have over 150 of these in stock. Were used for retort cooking bags and trays of rice and put into 1300mm wide retorts. Lhodpfxoqnwp So Afpeg

Condition: good (used), Handtmann VF628 vacuum filler with PVLS143 high speed linker cutter from 2021 and GS300 auto tray loading system consisting of GM310 and ZB311. Rarely available. We can offer an additional similar setup with VF622 instead of VF628. Lhodpfxsvvxumo Afpsg

Condition: good (used), JBT Proseal tray sealer in lovely condition. Just arrived today so photos show machine before cleaning. Has been used on a Christmas product packing sausagemeat stuffing and meatballs. Currently fitted with tooling for Linpac R2 trays. Fitted with optional ICE coder. Lhsdev Hh E Aopfx Afpeg

Condition: excellent (used), GT2 tray sealer with E-Seal option. In very nice condition. Lhodpferm Tg Ijx Afpjg

Condition: like new (used), Mobile racks for cookers and freezers etc. Dimensions 1760mm high x 800mm x 490mm. Each rack has 14 large deep trays 720mm x 420mm. 45 units available at £480 each Lhedeihgbhjpfx Afpeg

Condition: used, Year of construction: 2017, functionality: fully functional, load capacity per storage section: 1,500 kg, total length: 2,700 mm, total height: 100 mm, total width: 50 mm, Pallet rack / Heavy-duty rack / Beam L=270 from HLF Heiss Only the beams are being sold Used item, in excellent condition, see photos Supplier: HLF Heiss Lodpfx Aey H Ew Iofpjhg Quantity: 200 pcs Beam length: 270 cm Beam height: 10 cm / Width: 5 cm Maximum load per level: 1,500 kg Color: orange Including locking pins Year of manufacture: 2017 Item is in stock in Wilfersdorf near Mistelbach/Lower Austria. Transport available upon request. Inspection possible at any time by appointment.

Condition: good (used), Glass shelf depth per compartment: 65 mm Max. glass height: 1680 mm Width: 1500 mm Depth: 2600 mm Height: 2060 mm Condition: Good, second-hand Ljdpfsyx Uf Sox Afpshg

Year of construction: 2004, condition: good (used), Newsmith Crate / Tray Washer Up to 800 crates / hour All stainless steel Wash pump with detergent or soap agent facility Rinse pump with rinse agent facility Adjustable wash temperature controls Drive conveyor with 3 speed control selector All safety controls and e-stops Gas burner (can be changed to oil) Complete with extractor fan Lhodpfx Aoma E Hcofpog Ready for use

Condition: good (used), Year of construction: 2009, D2 Europack Tray / Pot Sealer Fully stainless steel In good working condition Lodst Tyivspfx Afpshg

Year of construction: 2021, condition: new, Derryglan Ltd - offer a wide range of industrial washer for every application, food, meat, butcher, bakery, pharma, labs, processors and general industry. Lhsdpjgq N Ezjfx Afpjg Washers for Utensils, Crates, Bins, Knife, Tray cleaning applications. JEROS Washers have a specially designed lid which opens fully to allow easy operation and loading without causing backstrain to operators. The special JEROS features provide easy installation of the machines. Even in the smallest production areas. Further, the machine can be used as a sink when not in use as an automatic Utensil Washer. The flush hose The flush hose makes it possible to reuse the wash water e.g. for cleaning the floors. The flush hose can also be mounted on the mixer tap if required. Mixer tap Built-in mixer tap allows washer to be used as a sink with separate drainage. Fulfils the highest hygiene standards Even the most persistent dirt is removed! The fully automatical detergent dispenser ensures the optimum dosage of soap. The powerfull pumps and rotating wash arms provide a brilliant wash result.The end rinse pump guarantees a constant temperature of 85?C during the entire rinse period and sanitisation of the utensils is achieved. An additional advantage of the high temperature rinse is the fast drying of utensils by evaporation, a rinse aid can be automatically added to assist with this process The New Generation The 9100 Series comprises a total of five new models: 9110 / 9115 with rotating wash systems and 9117 / 9120 / 9130 with wash frame system. Inside, the machines have been thoroughly redesigned, focusing on hygiene and easy cleaning. The inside surfaces and rounded to ensure quick and automatic flow of water back to the filter and pumps. Filters, wash arms and wash frames come in electropolished surface finishes leaving the stainless surface completely smooth to prevent dirt from sticking to surfaces of the machine. This makes it easier to clean and maintain the machine Efficiency and optimum hygiene safty, including HACCP, form the base of the JEROS, set of values. Energy saving up to 25 % All the machines are now available with 'i-version' as standard. This means that all machines have water saving rinse nozzles and that both the wash and rinse tanks are isolated, as also the lid is with double wall and isolated. The machines therefore require less operating power, resulting in energy and water savings of up 25 % for all the models. It is also possible now to set the machines to 'auto off', as required, so that they do not have to be left unnecessarily in standby mode if they are not used for prolonged periods of time, etc. Eco wash As standard all models includes an environmentally friendly 'ECO wash' programme for less dirty objects. Pushing 'ECO wash', the machines wash with a reduced wash temperature and use less soap. Still the rinse with 85? C hot water for guarantee of hygienic result New double Micro-Filter: Unique double filtration system, with a progressive micro-fine filter, provides an efficient filtration of the wash water - thus entails a perfect washing result with less soap consumption and minimal water consumption Larger particles are collected in a coarse filter, wereas smaller particles are captured in the self-cleaning micro-fine filter. During the washing/rinse process, the collected particles are drainet out of the micro-fine filter from the bottom, just as well from the surface of water. this ensure a constant optimum wash water quality