Used Water Recycling System for sale (9,925)

Condition: new, Year of construction: 2024, Gold River SWZ-700 water separators Application description: The GOLD RIVER SWZ series separator has been designed for special tasks, it can cope with the most difficult materials that contain many properties that disturb the separation process in separators commonly available on the market. SWZ water separators separate heavy fractions (non-ferrous metals) from, among others, plastics in the process of recycling secondary raw materials. SWZ separator equipped with a four-section copper water system equipped with radial nozzles with variable linear geometry. The separator uses the latest divided type of separation mat. The development of a modern module for preliminary division and preparation of material guarantees the purity of recovered raw materials in a very short time (plastics, metals). Hjdpjua Tbwjfx Ag Nonu Why a water system? Our device uses a system similar to that used in the gold recovery industry. We use water as a carrier and a force that affects the materials in a gentle way. In the water system, all particles with higher mass are gently washed out and separated, generating no losses during the entire separation process. The properties of water together with our proprietary solutions are unrivaled compared to, for example, air separators. SWZ type separators are used: Separation of heavy from light materials (metal granulates contaminated with plastic, foil, paper, cotton, fibers) Cleaning plastics after air separators (dry) Separation of metals in cable and non-ferrous metal recycling lines The SWZ-700 water separator, thanks to the use of the latest module, performs the separation process in a very short time, therefore it is characterized by a high hourly efficiency of separated material of approximately 1200 kg/h. Description of action: The material fed into the separator goes through the transport channel to the module for initial fraction division into its mass and humidity changes. Some of the material is separated at this stage. In the second part of the module, the humidity of the remaining batch changes. Then the material falls onto the separation table where the final fraction separation takes place. As a result of this process, we obtain valuable materials from both sides of the separator. Construction description: The massive structure and the inertial drive of the separator are made of materials appropriately selected to withstand the overloads resulting from vibrations. The supporting frame ensures excellent stiffness and failure-free operation for many years. Due to the type of vibration drive, the design does not require the installation of a soil separator. Separation table equipped with hydraulic adjustment of the angle of inclination. The separation table has a special module for initial division of fractions into their mass and preparation for final separation. The water system has several water pressure valves. The water circulation in the separator is closed. There is no need for constant access to an external water source because the device works using the water already in the tanks. Based on experience and continuous research in our laboratories. We are able to provide you with separators individually adapted to the specific nature of the material being separated. In various versions and sizes. SWZ-700 separators are manufactured to individual order.

Condition: new, Year of construction: 2025, Built on order Vibrating sieve to filter the process water. Process water is preferably used in a closed circuit. The authorities also see this as the ideal solution. Obtaining the permits for a recycling plant is greatly simplified by the use of a closed circuit and the costs of using the plant are significantly lower. Hedpfokzg Sdex Ag Nsnu

Condition: good (used), Young used vibrating sieve to filter process water. Made of 304 stainless steel, also suitable for salt solutions. Hnodpfx Agevy Dy Ns Nsu

Condition: new, Year of construction: 2025, functionality: fully functional, warranty duration: 24 months, New filling machine / filler suitable for filling liquids, pastes, creams, oils, etc. Typical applications include: - Disinfectants Hodpfx Agorivwfs Njnu - Shampoos - Creams - Honey - Jam - Milk - Yogurt - Water - Alcohol - Pesto - And more This is a robust machine powered by compressed air and 220V, fully Plug and Play! Ideal for small-batch filling operations. Even a small compressor is sufficient to operate this machine. A compressor can be supplied upon request. The filler features a 500ml cylinder, enabling a maximum fill volume of 500ml per cycle. For larger volumes, multiple cycles can be programmed. The minimum stroke is 50ml, and any volume between 50ml and 500ml can be dispensed in one cycle. The unit comes with a large 25L hopper. Optionally, it is possible to connect the system to an IBC or 200L drum, allowing for faster processing of larger batches. The machine is equipped with a foot pedal and automatic mode. In automatic mode, it continuously fills, making high-volume filling quick and efficient. With the foot pedal, operators can fill at their own pace. Depending on operator speed and fill quantity, 15–25 units per minute can be achieved, making this a very fast machine. It weighs approximately 15–20kg and is easily placed on a tabletop. The entire structure is made of stainless steel, ensuring high quality and durability. If you have any questions, please email us; we are happy to assist you with this or other machines. We also offer a labelling machine that pairs perfectly with the filling machine. We strive to respond within 24 hours and are available on working days from 09:00 to 17:30.

Condition: used, This listing is for the Grant GD120 Water Bath/Circulator The unit is in full working condition and is ready for immediate use The Grant GD120 is a digitally controlled stirred water bath and circulator ideal for laboratory use, offering high precision and flexibility. Here's a breakdown of its features and capabilities: Key Features Immersion Thermostat with Intelligent Control Optimisation (ICO): Enables adaptive PID control for exceptionally stable temperature regulation. Integral Pump: Built-in circulation pump with a maximum flow rate of 17 L/min, allowing both sample immersion and external fluid circulation. User Interface: Equipped with a clear digital display, a rotor plus two-key control, timer function for reaction timing, and visual + audible alarms to notify operators of critical conditions. Preset Temperature Control: Supports one adjustable operating setpoint plus three preset temperature options for fast switching. Safety Features: Includes float-switch low liquid protection and an adjustable over-temperature cut-out for sample and user safety. Liquid Type Selection: Automatically adjusts heater power and temperature parameters depending on chosen liquid (e.g., water, oil, glycol mixtures). Hnodpfx Ajxhfl Ejg Nsu Temperature Range & Accuracy Plastic Tanks (P-series): From around ambient +5 °C up to ~99 °C. Stainless Steel Tanks (S-series): From –15 °C up to ~120 °C. High Stability: ±0.02 °C for stable temperature control. Technical Specifications & Obsolescence The GD120 series includes multiple tank sizes: plastic tanks (P5, P12, P18) and stainless steel tanks (S5, S12, S18, S26, S38), offering varied capacities for different lab needs. This series is now considered obsolete, though it remains functional and reliable for many applications. Supporting Documentation & Manual Operating Manual: The GD120 is covered by the general purpose stirred thermostatic baths manual (shared with GD100), outlining temperature settings, calibration procedures, safety guidance, and maintenance. Datasheet Summary: Positioned within the broader Grant Optima product range, the GD120 sits between simpler (GD100, up to 100 °C) and higher-spec models (GR150 up to 150 °C, GP200 up to 200 °C)

Condition: excellent (used), operating hours: 2,658 h, functionality: fully functional, pressing force: 71 t, filling opening width: 1,000 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, input current: 200 A, oil tank capacity: 1,250 l, empty load weight: 29,000 kg, Technical data baler: Manufacturer BOA Recycling Systems B.V. Type M75-45-A-5-1.6 Ecoline Year of construction 2021 Hours of operation 2,658 hours (as of May 2024) Number of pressed bales 42,212 pieces (as of May 2024) Press power main press 71,2 kN (71 t) Specific press capacity 9 kg/cm² Operating pressure 280 bar Cylinder stroke 2,200 mm Feed channel 1,620 x 1,000 mm Hnsdpfou Thcvex Ag Neu Capacity per cycle time 2,4 m³ Theoretic cycle time 21 seconds Theoretic throughput rate 450 m³/hour Bale size 1,100 x 720 mm, length variably adjustable up to 1,400 mm Driving motor 45 kW Connected load 100 kW Current consumption 200 A Tying system 5-fold vertical, fully automatic, the press stamp is prepared for an additional 3-fold horizontal binding Throughput rate at a bulk weight of 30 kg/cbm approx. 13,6 tons/hour bulk weight of 50 kg/cbm approx. 24,2 tons/hour bulk weight of 100 kg/cbm approx. 36,4 tons/hour bulk weight of 150 kg/cbm approx. 54,7 tons/hour Bale weight up to 600 kg, depends on material Volume hydraulic oil tank 1,250 l SPS controller Siemens S7 1500 Operating panel Siemens SIMATIC HMI TOUCH Transport dimensions of press 10,000 x 2,800 x 3,385 mm (l x w x h) Press height set up with feed chute 4,743 mm Press height with conveyor belt 7,123 mm Machine weight baler approx. 29 tons Noise level <85 dB (A) Condition of the baler: With 2,658 operating hours, the press is almost as good as new and in very good condition, has hardly any signs of wear and is ready for immediate use. Due to larger material input quantities, the pressing force and throughput of the machine no longer meet the customer's current requirements and is therefore being replaced by a new 120 tonne baler. Only the baler is for sale, without conveyor belt and wire drawing stations. Comments: The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2025, In stock: The STF 3.0 floating sink separator with our highly efficient SP1000 Mk2 centrifuge and our VS1 water screen. A compact but powerful washing system that is low-maintenance and can wash/sort up to 3000 kg/h of hard plastics. The machines are made entirely of 304 stainless steel, so salt solutions can be used without any problems. An excellent starting point for a good homemade zinc float installation. Hnjdpfoxhf Nwex Ag Nju The machines are in stock and can therefore be delivered within a week. Ask us for further information.

Condition: like new (used), Baktec water Dosing machine and chiller In good working condition for more information please sent an request Hnjdjump Axopfx Ag Nju

Year of construction: 2010, condition: new, functionality: fully functional, Technical specifications: • Manufacturer: JMC Recycling Systems Ltd. (England) • Model: Dolphin 5005-Lite • Year of manufacture: 2010 • Connection: 380–415 V, 3-phase Hedpfxexm Uf Ss Ag Nenu • Recommended hydraulic oil: ISO 46 • Robust construction, mobile on wheels • Includes control unit and hydraulic drive Condition: • NEW, unused • Only storage marks present (see pictures) • No operating hours

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, 1. Waterjet cutting system with accessories, year of manufacture 2005, machine number: 95 246, Model 4060D, including: 2. Machine details: - NC 4060 D (Duplex with 6 cutting heads for abrasive cutting) - 1 x cutting table: 4200 x 6700 mm - X-axis travel: 2750 mm - Y-axis travel: 6470 mm - Z-axis travel (height): 250 mm - Positioning accuracy (X/Y): +/- 0.075 mm/m - Repeatability (X/Y): +/- 0.05 mm - Feed rate X: 10,000 mm/min - Feed rate Y: 10,000 mm/min - Feed rate Z: 4,000 mm/min Technical specifications: - 1 x Fanuc GE 300 i (NANO CNC) SYSTEM Control functions • 15-inch color LCD display (resolution 1024 x 768) • Machine control panel • 1.5 GHz Pentium III processor • Vertical and horizontal soft key bars • Slim operator panel with QWERTY keyboard • 40 GB program storage (hard disk) • 2 MB RAM for part programs • Windows 2000/XP operating system • Hand-held control unit (remote control) for easy axis positioning – 1 x MPG unit – 6 x WJS standard cutting heads mounted on holders (2 x 3 pieces) – 6 x SM 3000 abrasive metering units – 1 x IGEMS Standard or Professional Hodpfx Agsxgumco Njnu – 1 x documentation – 2 x abrasive storage tanks, 1,500 l each – 1 x sludge removal system, 3 x diaphragm pumps – 1 x wastewater tank 1,500 l – 1 x cascade tank – 1 x new stainless-steel cutting tank (4 x 6.7 m) - 10 m high-pressure hoses with fittings - 1 x KMT high-pressure pump, 100 HP, 4,100 bar, only 9,500 operating hours - Installation and maintenance by WJS personnel Machine connections: Electrical connection: 3 x 400 V+N+PE, 25 A, 50 Hz Compressed air supply: 600 l/min Air pressure (technically dried): 6.5 bar

Year of construction: 2025, condition: new, Zig Zag Air Sifter Hnedpfx Agjchb Rus Nju Sizes/ wides from 200mm - 1800mm Precondition for the separation are differences in the material like: - Different sizes of particles - Differences of the density - Differences in the surface condition of the particle - Differences in the form of the particle - Grain size 0.1mm - 40mm, (bigger particles are possible with a special design) We are the manufacturers of these plants and we build Zig Zag Sifter Plants in different sizes see attachment. In order to make you a definite offer we need to know some points: 1. What material you want to separate? 2. Grain-size of the material? 3. Bulk weight kg/liter of your material. 4. We have technical center at our house, where we can test your material.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l Hedpfsvf E Avsx Ag Nonu SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: new, Year of construction: 2025, In stock: The STF 3.0 floating sink separator with our highly efficient SP1000 Mk2 centrifuge and our VS1 water screen. A compact but powerful washing system that is low-maintenance and can wash/sort up to 3000 kg/h of hard plastics. Hjdpfx Asxhf H Neg Nonu The machines are made entirely of 304 stainless steel, so salt solutions can be used without any problems. An excellent starting point for a good homemade zinc float installation. The machines are in stock and can therefore be delivered within a week. Ask us for further information.

Condition: good (used), functionality: fully functional, Year of construction: 2016, operating hours: 500 h, Bunker dosing belt by R&T Recycling Technik Year of manufacture: 2016 Capacity: 2.5 m³ Hjdpfxsxcuvie Ag Nsnu Drive: 1.5 kW Frequency-controlled feed belt This system was integrated into a small pilot plant for approximately 3 months in 2016. The unit is in excellent condition and ready for operation. As shown in photo no. ..., this unit can be transported on a large tandem car trailer.

Year of construction: 2024, condition: new, ZIGZAG air separators Application description: ZIGZAG type air separator is a device designed to purify materials in the waste recycling process. The separator separates light fractions from heavy fractions by pneumatic method. It works well with a wide range of waste materials of 0-150mm size. Air separators of this type are used for pre-ground, jagged or very fine materials. Thanks to our unique design, the separator has the ability to adjust at many points that are important for the purity of the received fractions. ZIGZAG type separators are used in many areas: weight classification of metal granules Hsdpfx Agsua D Als Nonu purification of shredded scrap from the light fraction (films, plastics, paper) removal of volatile fraction during recycling of WEEE purification of plastics, rubber purification of municipal waste, glass removal of dust Construction description: The ZIGZAG separator consists of individual components mounted on a common support structure. In the first part, the ZIGZAG module is installed. The module has an inspection hole and regulation of the material stream passage gap. In the second part there is a cyclone discharging the light fraction. Underneath the cyclone there is a variable speed sluice for ejection of separated materials. A fan with electronic speed control is located on top of the structure. The structure is designed in part for loading and unloading by conveyor belts. The separator has a control cabinet equipped with a safety system.

Condition: like new (used), Year of construction: 2020, operating hours: 250 h, functionality: fully functional, 1.1 TECHNICAL DATA 1 x Waterjet cutting machine, NCP 4020 D 1 x FANUC 31iB d 1 x IGEMS Professional 1 x BevelJet cutting heads for AWJ abrasive waterjet cutting Hsdoxgua Aopfx Ag Nonu 1 x Fixed cutting heads for AWJ abrasive waterjet cutting 2 x SM3000 feed systems 1 x KMT, Jetline 50 HP, 3.8 l/min, 4100 bar 1 x Cooling unit control cabinet 1 x Hose reel with spray nozzle 1 x Tool kit 1 x Machine zone safety guard 1 x PanelOne HMI operator interface "EDGECUT" 1 x Remote control for high-pressure pump 1 x Remote maintenance system 2 x Diaphragm pumps and 2 x extraction units 1 x Waste container 1000 l 1 x Pressure vessel 200 l or 2-ton abrasive online conveyor/online abrasive hopper 1 x Head protection package (zero-point measurement head 1) 1 x IGEMS 5X CAM 1 x MPG, portable handheld pendant 1 x Rotary unit SS (chuck 240 mm) Price €21,000 1.1.1 MACHINE DATA Table size (W x D): 4200 x 2275 mm - Machining area (W x D): 3980 x 2010 mm - X-axis travel 2D: 3530 mm - X-axis travel 3D: 3220 mm - Y-axis travel 2D: 2010 mm - Y-axis travel 3D: 1405 mm - Z-axis travel: 250 mm - Positioning accuracy (X/Y): +/- 0.050 mm/m - Repeatability (X/Y): +/- 0.025 mm - Rapid traverse (X-axis): 30,000 mm/min - Rapid traverse (Y): 15,000 mm/min - Rapid traverse (Z): 5,000 mm/min - Minimum distance between nozzles: 450 mm - Maximum distance between nozzles: 2,010 mm 1.2 CONNECTION DATA 1.2.1 MACHINE CONNECTION • Electrical connection: 3 x 400 V+PE, 16 A, 50 Hz • Pneumatic supply volume (incl. pressure vessel): 500 l/min • Pneumatic supply pressure: min. 6.5 bar 1.2.2 HP PUMP DATA/CONNECTION HP pump data: - KMT 50, Jetline, 4100 bar - 37 kW, circuit breaker at 400/50 Hz, 80 A CAD/CAM software: - IGEMS Professional

Year of construction: 2025, condition: new, To sieve dry material: like flour-, grainy-, and granule-shaped material. Hnodpfechb Ryex Ag Neu Sizes from: wide 500-1500mm / length 1200-2400mm Sieve layers: 2 - 4 layers, granulation 0,1-18mm freely selectable.

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, Technical data on the EPS (Polystyrene) press: Manufacturer FZ-Recycling GmbH & Co. KG, Germany Type FZR 320 Year of construction 12/2022 Drive power shredder 4 kW Drive power of compactor screw 7.5 kW Drive power hydraulic unit for the holding clamp in the press channel 1.1 kW Total connected load 12.6 kW Current consumption 32 A Compaction ratio of the compacted blocks to the original product approx. 50:1 (depending on material) Block weight after compaction approx. 300kg/m³ (depending on material) Block dimensions 320 x 320 mm, variable length Throughput approx. 100 kg/hour, depending on material Hedpfeu Thkaex Ag Nenu Achievable density approx. 250 - 300 kg/m³ The pressed blocks are stacked approx. 1400 mm high on pallets and stretch-wrapped. Machine dimensions approx. 4,600 x 1,400 x 1,980 mm (l x w x h) Transport weight press 1,325 kg Condition of the baler: The press was only used sporadically, is in very good condition and available at short notice. Due to the low weight of the machine and the forklift shoes in the transport frame, the press is mobile and can be used directly on the construction site where the material is produced. The electrical connection is made via a CEE 32 A plug. Scope of delivery for the baler: 1 piece EPS press, ready for connection and use Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Item: D-10800-BacTerminator Hodjh Dxqvspfx Ag Njnu BacTerminator BTM10FD11001 Water Disinfection Equipment Inclusive pumps, Control and other accessories. Nice condition

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, machine/vehicle number: NC3015, repeat accuracy: 0.01 mm, travel distance X-axis: 2,550 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 200 mm, positioning accuracy: 0.01 mm, type of input current: three-phase, input voltage: 400 V, table length: 1,500 mm, table width: 3,000 mm, pressure: 3,800 bar, water pressure: 3,800 bar, Equipment: safety light barrier, Complete water jet machine water jet Sweden 3015. Made in 2007 and have been in use since then. Serviced by water jet sweden all the time. Sheet size 3000x1500 mm. Fanuc cnc. Kmt 50 hp pump in excellent condition with a lot of spare parts. 200 L sand hopper and a sand container for 1000 kg. Unit for cutting under water is also included. The machine is in very good condition. It is emptied and we can load it on a truck. Please ask if you want more pictures or if you have other questions. We can also put you in contact with water jet Sweden who has maintained the machine and know all about it. Hjdpfx Agew Sl Ezo Nonu

Year of construction: 2024, condition: new, WPS Eddy Current Separator, Magnetic Series. Eddy Current separators from the Magnetic Series are mainly used in the waste recycling industry. The use of eddy currents allows for the recovery of non-ferrous (non-magnetic) metals from loose waste such as aluminium, copper, brass etc. The WPS separators are characterized by high separation accuracy due to the original solutions by ZŁOMIARZE, which guarantees high profitability of waste recycling. WPS Separators are used in the recovery of: • non-ferrous metals from the recycling of electronic waste • non-ferrous metals from car recycling • metals from foundry waste • aluminium in glass recycling processes • non-ferrous metals from steel waste • non-ferrous metals from municipal waste To ensure the longevity of the equipment, the ZŁOMIARZE, as one of few companies, has introduced an improvement in the form of the central cooling of the bearings of the magnetic rotor, thanks to which the service life of the machine has been extended even several times. Technical Specification: • Magnetic field source – NdFeB magnets • Smooth adjustment of magnetic rotor speed – 0-3000 rpm • Belt speed adjustment • Belt position control system • Magnetic rotor cleaning cleats • Belt cleaning scraper • Material divider adjustable in two levels • Bearing cooling system (greatly extends bearing life) • Control panel with safety check Hnedpfx Agoiqxtbo Nsu For our non-ferrous metal separator we offer additional devices to make you separation process easier: • vibratory feeder • belt conveyors • magnetic drum/belt separators For more information please download our catalog. If you're interested in our products, please contact us!

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, machine/vehicle number: 95521, Water Jet Sweden NCP 4020 D Year of manufacture: 2009 1.1 TECHNICAL DATA 1 x Water Jet Cutting Machine, NC 4020 D 1 x FANUC 310iA control unit 1 x IGEMS CAD/CAM software 2 x Fixed cutting heads for AWJ abrasive waterjet cutting 2 x SM3000 feed units 1 x KMT Jetline, 50 HP, 3.8 l/min, 4100 bar 1 x Cooling unit & control cabinet 1 x Hose reel with spray nozzle 1 x Tool kit 1 x Machine safety enclosure 1 x PanelOne HMI "EDGECUT" operator interface 1 x Remote control for high-pressure pump 1 x Remote maintenance 2 x Diaphragm pump and extraction units 1 x Waste container, 1000 l 1 x Pressure vessel, 200 l, and 1-ton online abrasive conveyor/online abrasive container 1 x Starter hole drilling unit 1 x MPG, portable manual control unit 1.1.1 MACHINE DATA Table dimensions (W x D): 4200 x 2275 mm - Cutting area (W x D): 3980 x 2010 mm - X-axis travel (2D): 3530 mm - Y-axis travel (2D): 2010 mm - Z-axis travel: 250 mm - Positioning accuracy (X/Y): +/- 0.050 mm/m - Repeatability (X/Y): +/- 0.025 mm - Rapid traverse X: 30,000 mm/min - Rapid traverse Y: 15,000 mm/min - Rapid traverse Z: 5,000 mm/min - Minimum distance between nozzles: 450 mm - Maximum distance between nozzles: 2010 mm 1.2 CONNECTION DATA 1.2.1 MACHINE CONNECTION Hsdew Snybspfx Ag Nsnu • Electrical connection: 3 x 400 V + PE, 16 A, 50 Hz • Pneumatic supply volume (incl. pressure vessel): 500 l/min • Pneumatic supply pressure: min. 6.5 bar 1.2.2 HP PUMP DATA/CONNECTION HP pump data: - KMT 50, Jetline, 4100 bar - 37 kW, circuit breaker at 400/50 Hz, 80 A CAD/CAM software: - IGEMS

Year of construction: 2025, condition: new, Circle Sievemachine to sieve dry material: like flour-, grainy-, and granule-shaped material. Hnodpfxobcngio Ag Neu Sizes from: wide 500-1500mm / length 1200-2400mm Sieve layers: 2 - 4 ply, granlulation < 18mm freely selectable.

Condition: excellent (used), Year of construction: 2004, operating hours: 34,480 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 19,000 kg, transport height: 3,300 mm, oil tank capacity: 750 l, power: 45 kW (61.18 HP), Technical data baler: Manufacturer Bollegraaf Typ HBK 100 Year of construction 2004 Hours of operation 34,480 hours Hnsdpfx Aexbgnhjg Nju Press power main press 100 tons Press power of pre-press max. 42 tons Feed channel 1,600 x 1,100 mm Filling volume 3.15 m³ Theoretic cycle time 22 sec. Theoretic throughput capacity up to 450 m³/hour Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical, fully automatic Throughput rate at a bulk weight of 30 kg/cbm approx. 13 tons/hour bulk weight of 50 kg/cbm approx. 20 tons/hour bulk weight of 100 kg/cbm approx. 30 tons/hour Throughput rate with ruffler approx. 20 tons/hour Bale weight 550 up to 750 kg, depends on material Volume hydraulic oil tank 750 l SPS controller Telemecanique TSX Micro Transport dimensions only baler 10,900 x 2,320 x 3,300 mm (l x w x h) Machine weight baler approx. 19 tons Comments: Unlike the standard HBC press series from Bollegraaf, this machine does not have a pre-press flap but cuts the material between blades on the press ram and the counter blade in the frame. This makes it a cutting edge press, similar to a Paal, unoTech, etc. The press is in very good condition for its age, as it was used exclusively for compressing paper from document destruction. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2025, condition: new, Circle Sievemachine to sieve dry material: like flour-, grainy-, and granule-shaped material. Sizes from: wide 500-1500mm / length 1200-2400mm Sieve layers: 2 - 4 ply, granlulation 0,1-18mm freely. selectable. Hsdpfx Agobcnatj Nonu