Channel Bailing Press

PAAL PACOMAT 1S

Condition: like new (used), functionality: fully functional, Year of construction: 2025, operating hours: 55 h, Machine with special rotor available immediately Advantages: + special rotor with reduced blade overhang, suitable for hard and soft materials + 22 kW motor Djdpfx Abox Af Rdjaekn + effective square blades *for pallets: up to a maximum of 10 pallets per hour *dependent on screen size and material. With smaller wood residues, significantly more. Motor: 22 kW; 400 V - 50 Hz - 3 phase, Screen: 15/20 mm or as agreed (10 to 40 mm possible) hydraulically operated slide Screen opening currently (15/20 mm) *can be exchanged Extraction nozzle Ø 200 mm. Feed opening 1000x1000 mm Dimensions: 2000x1800x1645mm Example image above: color of the system may vary Weight: 1920 kg. Included as standard: - Control cabinet with PLC control - automatic star/delta start - fast hydraulics - auto. OFF when the rotor is idle - speed 70-90 rpm for high throughput - cycle control to avoid idle times - performance-enhancing step control of the hydraulic slide - Pertinax guides for hydraulic slide - vibration-damping machine feet - CE compliant The following options are available at an extra cost: - Raise shredder by 30 cm (preparation for conveyor belt) + €2,480 net - Inclined conveyor belt (discharge height approx. 220 cm) + €12,980 net - Overband magnet + €6,980 net - Control for conveyor belt and overband magnet + €2,750 net (Start and stop synchronized with the shredder) - extended feed hopper 1500x1500 mm + €3,480 net Requirements for the raw material: - The moisture content (as received) must be below 25% - The feed must be free of metals and mineral contaminants. Damage to the tools and/or increased wear may result.

Condition: used, Year of construction: 2006, functionality: fully functional, center height in crank: 1,100 mm, workpiece weight (max.): 180,000 kg, grinding length: 11,000 mm, grinding wheel diameter: 1,066 mm, total length: 11,700 mm, quill travel distance: 11,700 mm, workpiece weight between centers: 180,000 g, distance between centers: 11,700 mm, POMINI CNC Roll Grinder Model HD-425-2-7L Siemens 840D, 12 Axes. Built in 2006. Two flatbed system grinding and workpiece ways are separate. Machine accuracy. Straightness 0.001-0.002 mm/m. Roundness 0.001-0.002 mm. Eccentricity 0.002 mm. Profile for crown height up to 0.1 mm ±0.002 mm/m. Surface finishing without chatter marks and no feed marks after finishing grinding stage. On an independent bed: Auto Caliper Diameter 870 - 2,250 mm. Eddy current crack and bruise detector probe. Ultrasound depth probe up to 180 mm. High Pressure wheel cleaner. Wheel dynamic balancing electromagnetic automatically or manually. Wheel dressing device with diamond. 2 Hydrostatic Steadies. 2 Hydrodynamic Steadies. 4 Soft landing for roles. Wheel quick change device incl motor. Jib crane. Vibration Measurement, recording on: Headstock base Neckrests Foot stock Wheel head Wheel head back Carriage Lateral side. Working Capacity. Grinding length 11,000 mm Max diameter with 1,066 mm Grinding wheel 2,200 mm Min diameter with 1.066 mm Grinding wheel 800 mm Center distance 11,700 mm Max Roll weight 80 Tons Max Roll weight with Steadies 180 Tons Min distance between wheel center and roll axis 845 mm Max distance between wheel center and roll axis 1,635 mm Carriage Axis Z, Hydrostatic Feeds, Infinitely variable 0-6,000 mm/min Oil film thickness 0.020 mm Distance between carriage ways 1,500 mm Ways width 160 mm Total length of the carriage on ways 3,385 mm Wheelhead on Carriage Axis X, Wheel Probe Axis A, Inspector Axis A1, Wheelhead cross travel Ballscrew, Axis X 940 mm Resolution axis X 0.0001 mm Wheel Spindle length 1,695 mm Spindle bearing, hydrostatic, diameter 254 mm Resolution Infeed micrometer handwheel, Axes X 0.00001 mm / division Continuous wheel infeed, U axis on radius 0 - 0.35 mm/min Rapid wheel indeed, axes X 0-830 mm/min Wheel motor, AC 130 kW Wheel Speed 400-1,100-1,600 rpm Wheel Cutting Speed infinitely variable Surface speed wheel diameter 1,066 mm 45 m/sec Surface speed wheel diameter 670 mm 45 m/sec Wheel hole, diameter 508 mm Wheel thickness 76 - 152 mm Wheel diameter 670 - 1,066 mm Crowning, Axis U. Max crown on the diameter 10 mm Max concavity on the diameter 10 etc Head stock Workpiece rotating speed 5 - 50 rpm Headstock motor 200 kW Max transmissible torque 76.5 kNm Faceplate control system V Belts Max Center diameter, metric type 160 mm Stroke of Quill 150 mm Length of headstock 3,110 mm Tail stock Quill diameter 260 mm Stroke of quill 750 mm Maximum center diameter, metric type 160 mm Taper Metric 5% on the diameter Dksdpjwdmy Ssfx Abaon Tailstock length 1,300 mm Stroke of tailstock 8,000 mm Caliper, Arm Axis C, Carriage Axis V, Rotation Axis B. Max measurable diameter 2,250 mm My measurable diameter 870 mm Machine Dimensions. Machine weight 130 tons Length 19.5 m. Width 5.5 m. Height 3.2 m. Foundation depth 3.8 m.

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, Used Andritz Paladin 600B Dkjdpfsx N T Uaex Abaen Incl. combined stainless steel feed auger and mixer, 2x 55kW motors, other motor options negotiable Interior inspected 2 years ago Includes frame for roller and die change

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. Dsdpfevf E Avsx Abaekn The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: new, Year of construction: 2026, functionality: fully functional, power: 11 kW (14.96 HP), A triple pass rotary drum dryer is a type of industrial dryer that is used to reduce or remove moisture from a material. It gets its name from the three rotating drums through which the material passes, each with a different purpose in the drying process. This type of dryer is commonly used in the production of various bulk solids, including minerals, agricultural products, and biomass. Here are the key features and components of a triple pass rotary drum dryer: 1. Triple Pass Design: - The material being dried passes through three rotating drums or cylinders, hence the term "triple pass." Each drum serves a specific purpose in the drying process. 2. Material Flow: Djdpfx Ajq Nfuzobaskn - The material enters the dryer and first passes through the innermost drum. After the initial drying phase, it moves to the middle drum and then to the outer drum, undergoing additional drying in each pass. 3. Heat Source: - Heat is typically provided by a combustion system, such as a burner or furnace, located at one end of the drum dryer. The hot gases generated by the combustion process flow through the rotating drums, transferring heat to the material. 4. Air Flow: - The dryer is designed to optimize air flow through the drums, ensuring efficient drying. In a triple pass design, the material and hot gases move counter-currently through the three drums, enhancing heat transfer and drying efficiency. 5. Lifting Flights or Lifters: - Lifters are internal components inside the drums designed to lift and cascade the material as it rotates. This movement promotes good heat transfer and uniform drying. 6. Retention Time: - The triple pass configuration allows for an extended retention time of the material in the drying system. This longer exposure to heat enhances the drying efficiency, making the triple pass rotary drum dryer suitable for materials with high moisture content. 7. Cooling Section: - After the material completes the three passes and reaches the end of the drum dryer, a cooling section may be included to reduce the temperature of the dried material before it is discharged. 8. Applications: - Triple pass rotary drum dryers are used in various industries, including agriculture (drying crops like grains), minerals (drying ores or concentrates), and biomass (drying wood chips or other organic materials). 9. Efficiency and Energy Consumption: - Triple pass rotary drum dryers are known for their high efficiency due to the extended drying time and effective heat transfer. However, they may have higher energy consumption compared to single or double pass dryers. When selecting a triple pass rotary drum dryer, it's essential to consider factors such as the type of material to be dried, required moisture reduction, and overall processing requirements. Proper design and operation are crucial to achieving optimal drying performance. Technical details We have different options for different requirements, please contact our team for more info.

Condition: not inspected (used), Year of construction: 1985, functionality: fully functional, pressing force: 50 t, bale length: 1,000 mm, bale width: 750 mm, bale height: 750,750,750 mm, bale weight: 500 kg, input voltage: 400 V, overall weight: 7,500 kg, oil tank capacity: 500 l, power: 30 kW (40.79 HP), empty load weight: 7,500 kg, input frequency: 50 Hz, Manufacturer: Paal Typ: Pacomat V Year of construction: 1985 Press power main press: 50 t Specific press capacity: 5 kg/cm² Feed channel: 1.000 x 720mm (l x w) Theoretic throughput rate: 200 cbm/h Bale size: 700 x 1.000 mm (w x h) length adjustable Dsdpfx Abjic Rl Deaskn Driving motor: 30 kW Bale weight: approx. 500 kg Machine weight: approx. 8000kg The hydraulic unit is functional, the drive motor is in the removed state.

Condition: reconditioned (used), machine/vehicle number: 550-235-ELD, GENERAL CHARACTERISTICS workpiece Ø max. 41 mm Range Module máx/min. 1,5 / 0.39 Rack face width 92 mm Dksdod Nw Ttspfx Abajn Manufacturing No. 550-235-ELD Máx/min. pitch form 20/40-32/64 Maximum stroke of tools trolley 760 mm Rack length máx. 610 mm ELECTRICAL CHARACTERISTICS Main motor power 15 Cv

Year of construction: 2019, operating hours: 1 h, condition: as good as new (ex-display), machine/vehicle number: MISCO1082, Oil Mist Collecting and Regaining. MISCO is used for collecting and getting rid off the oil in the CNC machines cabin. It is a water vapor, aerosol, smoke, oil mist filtering / separating device. Also allows condensing and recycling the condensed liqud back to the sump Djdpod Nwk Usfx Abaskn The particulate-smoke-gas-water in the air sucked in is filtered through the vapor separation units. The saturated oil-water etc. contained in the air is also separated and recovered, and the air is cleaned by 98% of the dry air. Removal of parts washing machines vapor-mist, Welding fumes, Oily air off CNC machines In the industry and even In the industrial kitchens a lot of oil mist, various gases, fumes and dusts are mixed into the air and create a risk of fire. In addition, they are inhaled by workers and cause damage especially to the lungs, respiratory tracts and other vital organs. For this reason, harmful substances such as gas, dust, smoke and similar substances must be cleaned by absorbing harmful substances in terms of safety and health. Application Areas: CNC Machines Welding fumes, Allows removal of oil vapor and recovery of existing fluid in CNC machines Automotive - Metal Processing – Food Industry - Industrial Kitchens - Steel - Casting - Chemical Industries etc. Working Principle; 1-Entry of dirty smoke –vapor- mist 2- Condensation with laminar flow over the walls 3- Disintegration of the particles passing through the filter 4-Recycling of condensing liquid 5-Dry and clean air evacuation For detailed information please contact us. mistcollector, cnc cutting oil, fume removal, cutting oil fume collector

Year of construction: 1955, condition: used, Radial drilling machine, drilling machine, boom drilling machine -Outreach: 2055 mm -Max. Distance from machine table to spindle mount: 1700 mm -Cone mount: MK5 -Motor power: 7.5 kW -Speeds: 11.2-1400 rpm -Columns: Ø 450 mm -Spindle stroke: 540 mm -Thread cutting device -automatic feed: 0.037-2.0 mm/rev -Clamping area: 920 x 1600 mm -Dimensions: 2580/1110/H3450 mm Dodpfx Aed Enr Iobajkn -Weight: 6465 kg

Condition: ready for operation (used), Year of construction: 1997, MODEL U.M. TG20/2500 CNC SIEMENS 840 C TURNING DIAMETER: 2500 mm TABLE DIAMETER: 2000 mm TURNING HEIGHT: 2000 mm MAX. WORKPIECE WEIGHT ON TABLE: 20000 kg MAX. TABLE SPEED: 2-250 rpm Djdpfxexwp D Ds Abajkn TOOL CHANGER: 10 pcs TABLE MOTOR: 60-100 kW C-AXIS RAM SECTION: 250x250 mm RAPID TRAVERSE: 10000 mm/min MILLING SPEED: 0-4000 rpm DRIVEN tools WEIGHT: 46000