Flatbed

Van Hool 3B073 |3 AXLE FLATBED | STACK OF 5 SEMITRAILER...

Condition: used, mileage: 899,000 km, power: 315 kW (428.28 HP), first registration: 11/2014, fuel type: diesel, overall weight: 18,000 kg, axle configuration: 2 axles, next inspection (TÜV): 10/2024, brakes: retarder, color: blue, gearing type: automatic, Year of construction: 2014, Equipment: ABS, air conditioning, electronic stability program (ESP), parking heater, Special equipment: Airbag driver's side, Audio system: CD radio (Bluetooth), Compressed air connection in cab, Compressed air tank aluminum, Compressed air horn, Driver assistance system: Attention-Assist (drowsiness detection sensor), Driver assistance system: Brake assist (Active Brake-Assist 3), Driver assistance system: Lane departure warning system, Cab: with air suspension, Suspension: front springs 7.5 t, 2 leaf, Fleetboard vehicle computer, Tinted windshield, Info display 12.7 cm with additional display, Cabin filter construction site vehicles, LM rims 11.75x22.5 (ALCOA matt, on front axle), LM rims 9.00x22.5 (ALCOA matt), mounting plate / fifth wheel plate 40 mm for fifth wheel coupling, reinforced engine brake, auxiliary drive MB 131-2c, frame lowering without bellows residual pressure control, tire pressure control system, retarder, automatic circuit breaker, seats in cab: Driver's seat comfort swivel seat, sun visor outside, sun protection roller blind side window, driver's door, socket 12V in passenger footwell, socket 24V / 25 A in passenger footwell, preparation / switch lift axle on semitrailer / trailer, preparation fleetboard, preparation cool box / refrigerator, oil cooler gearbox Further equipment: Dodpfx Abovhzffeueun EURO 6 emissions standard, axle configuration: 4x2, axle load front axle 7.5 t, Actros 4, trailer socket 24V / 15-pin, work lights, exhaust to right outside, exterior mirrors electr. adjustable and heatable, differential lock rear axle, compressed air unit medium, cab: width 2.30 m, cab: L StreamSpace, cab floor with engine tunnel 320 mm, suspension: leaf / air, suspension: front spring block aluminum, electric window regulator, generator 100 A, transmission 12-speed - type: G 211-12, urea tank (AdBlue): 60 ltr, rear axle disk wheel 440, body/body: tractor unit, comfort couch below, comfort locking system, communication interface, 3-part mudguards, radiator blind, regulated power steering pump, 2-stage air compressor, engine 10.7 ltr. - 315 kW R6 diesel (OM 470), engine compartment encapsulation, ramp mirror, residual heat utilization, front and rear axle disc brakes, seat cover / upholstery: fabric, seats in cab: passenger function seat, seats in cab: Driver's seat backrest can be folded down, Voltage transformer 24V / 12V 10 A, Front splash guard, Front axle stabilizer bar, External left-hand storage flap, 24V cab socket, Tachograph / EC tachograph, Door extension for cab, Aerodynamically shaped underbody panelling, Front underride guard, CB radio preparation, Toll collection preparation, Cranked front axle, Regulated water pump, Perm. Gross vehicle weight 18.00 t, Auxiliary heating (water)

Condition: refurbished (used), Year of construction: 1999, functionality: fully functional, pressing force: 71 t, filling opening width: 1,080 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, total width: 3,450 mm, total height: 4,090 mm, total length: 10,020 mm, input voltage: 400 V, overall weight: 27,000 kg, noise level: 85 dB, pressure: 300 bar, transport height: 2,300 mm, power: 37 kW (50.31 HP), Fully automatic channel baler with pre-press flap available immediately. The machine includes a conveyor belt with a floor-mounted section. The baler is supplied in refurbished condition and the conveyor belt underwent a belt overhaul at the beginning of this year. The machine was taken out of production at the beginning of October and is currently stored in our facility. It can be demonstrated in operation at our location. This machine is particularly suitable for baling paper/cardboard and various types of plastics such as PET, HDPE, and big bags. Technical specifications baler: Dedpexl Rqbsfx Abuoun Drive: 37 kW Press force: 71 tons Bale dimensions: 1100 x 720 x 1300 mm (length adjustable) Number of wires: 4 vertical Filling hopper dimensions: 1620 x 1080 mm Bale weight: up to 600 kg (depending on material) Capacity: up to 20 tons per hour (depending on material) Transport weight: 27,000 kg Technical specifications conveyor belt: Length of horizontal section: 3,000 mm Length of inclined section: 7,424 mm Angle: 29° Filling option: at floor level

Year of construction: 2003, operating hours: 43,000 h, condition: repair required (used), machine/vehicle number: HBC 140 2x75kW 2003 (W230-005), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2003 Hardox bottom floor plate only Plastic valve Anti-rat cabling Hours 43.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, Dsdpfxekcgynj Abueun • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: HBC 140 2x75kW 2001 (210-008-01), pressing force: 155 t, bale weight: 1,500 kg, pressure: 250 bar, power: 150 kW (203.94 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Duedetvau Aepfx Abuon Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: like new (used), functionality: fully functional, mileage: 167,896 km, power: 463.36 kW (629.99 HP), first registration: 11/2015, fuel type: diesel, fuel: diesel, brakes: retarder, color: white, gearing type: automatic, Year of construction: 2015, Equipment: ABS, airbag, Mercedes-Benz ACTROS 1863 - First registered: 11/2015 - Retarder: Installed - Mileage: 167,986 km - Stationary air conditioning - Dual fuel tank - Tyres at 40% FINANCING OR CUSTOMIZED LEASING OPTIONS AVAILABLE ON SITE. FROM 24 UP TO A MAXIMUM OF 96 INSTALMENTS, EVEN WITH ZERO DOWN PAYMENT. OTHER BRANCHES OF OUR GROUP: DOMENICO TRUCK SRL NAPLES BRANCH DOMENICO ESPOSITO S.P.A. EBOLI (SA) BRANCH – OFFICIAL DEALER MERCEDES-BENZ, FUSO, FOTON TRUCK, PIAGGIO COMMERCIAL AND MAXUS CONTACTS: 0823 1686306 335 6713062 – 377 7064530 BRANCH OPENING HOURS: MONDAY-FRIDAY 8:30/19:00 – SATURDAY 08:30/14:00 WE OFFER A WIDE RANGE OF USED MULTI-BRAND COMMERCIAL/INDUSTRIAL VEHICLES: Dedpfewypa Tsx Abuoun Fiat – Hyundai – Daf – Mercedes Benz – Renault – Peugeot – Iveco – Mitsubishi – Scania – S-Way – S500-V8-650-580-730-S500-S 500-S500 – Stralis – Man – Nissan V8 – Intarder – 770s – Limited Edition – 660 S semi-trailer – Refrigerated semi-trailer – Lamberet – Schmitz – Isuzu – Fixed bed – Crane – Tipper – 4 axle – Rear 4 axle – Tway – T-Way-540 – 460 HP – Xway – X-Way – Three-way tipper – V8 – Scania – Frost Edition Curtainsider – Box body – Tailgate loader – Refrigerated unit – Insulated with fridge – Van Domenico Truck srl declines any responsibility for possible discrepancies in technical specifications, options or features which may in some cases differ from those reported in the description. We invite you to verify the characteristics of the specific vehicle.

Condition: excellent (used), Year of construction: 1998, functionality: fully functional, pressing force: 25 t, filling opening width: 800 mm, filling opening length: 1,050 mm, bale width: 900 mm, bale height: 800 mm, input voltage: 400 V, noise level: 85 dB, power: 18.5 kW (25.15 HP), volume flow: 160 m³/h, Bollegraaf HBK25 offered in Cyprus. The machine is in good condition and includes a floor conveyor belt. The machine is immediately available. Technical specifications of the baler: Drive: 18.5 kW Bale size: 800 x 900 x adjustable Feed hopper dimensions: 1,050 x 800 Press force: 25 tons Capacity: 160 m3/hour (depending on material) Technical specifications of the conveyor belt (approximate): Length on floor: 3,000 mm Diagonal length: 5,000 mm Dedoxbdgujpfx Abusun

Year of construction: 1999, condition: good (used), Used Bühler controlsieve 4kW Drive Dodpfx Abjhq Hq Soujun Stainless steel sieve ø1mm Inlet ø200 Outlet ø200

Condition: new, Year of construction: 2025, functionality: fully functional, Labelling machines for self-adhesive labels. Nearly all applications and speeds are possible. 6000–9000 bottles per hour are no problem. Depending on requirements, the machines are equipped with 1 or 2 stations for self-adhesive labels—front, back, and/or wrap-around labelling. Label width: as required Label length: as required Bottle format: any format possible Further information and additional machines available on request. Duedpox Dx Ncjfx Abuon

Condition: like new (used), functionality: fully functional, mileage: 900,170 km, power: 315 kW (428.28 HP), first registration: 12/2008, fuel type: diesel, maximum load weight: 26,000 kg, overall weight: 44,000 kg, axle configuration: 6x2, brakes: retarder, color: white, gearing type: semi-automatic, emission class: euro5, suspension: steel-air, Year of construction: 2008, operation weight: 14,080 kg, Equipment: ABS, air conditioning, cabin, differential lock, hydraulics, parking heater, retarder, Mercedes-Benz Axor 2543 3-way tipper (internal dimensions: 6.45m long / 2.44m wide / 1.00m high) 6x2 differential lock front leaf suspension – rear air suspension EPS gearbox with clutch pedal Euro 5 gross vehicle weight 26,000kg – payload 14,080kg tow hitch (permissible gross train weight 44,000kg) 3rd axle height-adjustable and steerable total truck length 8.90m tyres 80%-60% Dusdpfx Ajxrb R Esbuen wheelbase 4.20m 700L tank aluminium rims sun visor fog lights central locking air conditioning auxiliary heater electric windows and exterior mirrors sleeper cab with 1 bed ABS All information without guarantee / subject to errors

Condition: new, Year of construction: 2020, functionality: fully functional, power: 320 kW (435.08 HP), Brand new Mercedes-Benz OM 470 engine. Suitable for multiple cranes. Contact for price and other engines available. Duedpfx Aoxw R Dxobuon