Shredder

ZENO GmbH ZTLL 1200x1600

Condition: new, Year of construction: 2024, Gold River SWZ-700 water separators Application description: The GOLD RIVER SWZ series separator has been designed for special tasks, it can cope with the most difficult materials that contain many properties that disturb the separation process in separators commonly available on the market. SWZ water separators separate heavy fractions (non-ferrous metals) from, among others, plastics in the process of recycling secondary raw materials. SWZ separator equipped with a four-section copper water system equipped with radial nozzles with variable linear geometry. The separator uses the latest divided type of separation mat. The development of a modern module for preliminary division and preparation of material guarantees the purity of recovered raw materials in a very short time (plastics, metals). Why a water system? Our device uses a system similar to that used in the gold recovery industry. We use water as a carrier and a force that affects the materials in a gentle way. In the water system, all particles with higher mass are gently washed out and separated, generating no losses during the entire separation process. The properties of water together with our proprietary solutions are unrivaled compared to, for example, air separators. SWZ type separators are used: Separation of heavy from light materials (metal granulates contaminated with plastic, foil, paper, cotton, fibers) Cleaning plastics after air separators (dry) Separation of metals in cable and non-ferrous metal recycling lines The SWZ-700 water separator, thanks to the use of the latest module, performs the separation process in a very short time, therefore it is characterized by a high hourly efficiency of separated material of approximately 1200 kg/h. Description of action: Chjdpfxoua Tbws Abred The material fed into the separator goes through the transport channel to the module for initial fraction division into its mass and humidity changes. Some of the material is separated at this stage. In the second part of the module, the humidity of the remaining batch changes. Then the material falls onto the separation table where the final fraction separation takes place. As a result of this process, we obtain valuable materials from both sides of the separator. Construction description: The massive structure and the inertial drive of the separator are made of materials appropriately selected to withstand the overloads resulting from vibrations. The supporting frame ensures excellent stiffness and failure-free operation for many years. Due to the type of vibration drive, the design does not require the installation of a soil separator. Separation table equipped with hydraulic adjustment of the angle of inclination. The separation table has a special module for initial division of fractions into their mass and preparation for final separation. The water system has several water pressure valves. The water circulation in the separator is closed. There is no need for constant access to an external water source because the device works using the water already in the tanks. Based on experience and continuous research in our laboratories. We are able to provide you with separators individually adapted to the specific nature of the material being separated. In various versions and sizes. SWZ-700 separators are manufactured to individual order.

Condition: new, Year of construction: 2025, Laser power: 6000W/12000W/20000W Applicable Material: metal Condition: New Laser Type: Fiber Laser Chsdpfeg Du Aqex Abrsd Cutting Area: 3000*1500mm Cutting Speed: 200m/min Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT Cooling Mode: WATER COOLING Certification: CCC, CE, GS, ISO, Sgs Laser Source Brand: IPG/MAX Weight (KG): 11000KG Warranty: 3 years Power supply: 110V/220V/380V 50Hz/60Hz 1. Flagship Series Super dynamic responding, easily handle complex patterns of sheets. 2. Automatic Edge-finding With the capability of identifying irregular sheets, the edge searching time is decreased to 3 seconds. 3. Automated Nozzle Changer The machine changes its nozzle within 35 seconds at the fastest speed - this saves 50% of time costs.

Condition: ready for operation (used), Year of construction: 2012, functionality: fully functional, total height: 3,400 mm, total width: 2,400 mm, total length: 3,900 mm, overall weight: 6,000 kg, input voltage: 380 V, power: 80 kW (108.77 HP), rotary shear 2 shafts - 2 motors 40kw - inversion in case of jam - shredding chamber 1100 x 900 - thickness of new knives 80 - 5 tons - large loading hopper - possibility of loading Chodpjh Diwusfx Abrsd very versatile and very powerful, can pre-grind organic matter for methanizers, copper cables, lumps, plaster, BA13, D3E, plastics, wood, bumpers, bottles, metals, hollow bodies, etc. use to grind up sick calves at the renderer.

Year of construction: 2021, condition: new, Aluminum inclined belt conveyor including subframe inclined section starting at 50mm (adjustable) discharge area 1500mm (adjustable) Chjdpfxjhh Dbaj Abrjd belt width 500mm (adjustable) We supply our belt conveyors in PVC, PU or rubber. PVC belt including cleats and wave edge Drive: 0.25kW motor (adjustable), speed 0.3m/sec Connection 220/240V, 50Hz, protection class IP54 Drive, etc., ready for connection, motor control optional 6 adjustable machine feet for alignment Wave edge: 40x35mm (adjustable) T-20 cleats - 400mm pitch (adjustable) 2-ply, particularly resistant to transverse forces Our core competence lies in providing customers with exactly what they need. We work together with our customers to develop customized, individual solutions and supply corresponding equipment from our own production. Contact us by phone to find a suitable solution for your application. Belt conveyor, conveyor system, discharge conveyors, belt conveyors, magnetic separators, overband magnetic separators, recycling, wood chips, plastic, metal detection (metal-free), neodymium, overband magnet, magnetic belt separator.

Year of construction: 1991, condition: excellent (used), Fully automatic gate system HDN 600 with automatic infeed ZE, including mechanization. Technical data: Passage height: 700 mm Codsz Ehfajpfx Abrshd Passage width: 735 mm Stroke: 600 mm Feed rate: max. 15 m/min Water-cooled guides Drive – Gearbox The system has demonstrably only been in operation for 10 years.

Condition: used, Year of construction: 2023, No. 10017 Two-fraction star screen GÜNTHER MULTISTAR ONE / MS ONE Chodewhy T Tjpfx Abrsd Used, year of construction 2023 Approx. 200 operating hours Mobile star screen for screening waste wood, biomass, green waste and other screenable materials in 2-fractions as well as for overlength recycling - Input material: specific weight 200 - 650 kg/m³ / moisture max. 55% / piece size and individual weight max. 1000 mm and 20 kg / material feed with conveyor belt or wheel loader / throughput capacity up to 200 m³/h - Control, operation, switch cabinet: Type PLC / Operation display, control panel / Manual or automatic operating mode / Power supply AC 400 V, 3P, 50Hz via 32A plug on site - System interlinking: 16-pin plug connection / Cable (15 m) incl. winding device on base frame / Screen deck overrun for EMERGENCY STOP / Dummy plug in control cabinet door - Hydraulic support legs: 4 hydraulic support legs / Increase the discharge height of the useful fraction by 450 mm / All support legs can be controlled individually - Feed hopper: Capacity approx. 2.5 m³ / Feed height 2500 - 3000 mm / Free throw-in length 2300 mm / Conveying medium scraper chain conveyor with maintenance-free flat link chain / Drive 2.2 kW adjustable via frequency inverter - Collecting belt: Center distance 4600 mm / Belt width 1000 mm / Belt type smooth / motor 2.2 kW, v=1.2 m/s - Connect: Connect! is the innovative telematics solution from Komptech / overview of operating status, error messages, statistics, GPS localization, capacity utilization - Petrol-powered hydraulic pump - HyDrive System 2.0 MS ONE - Screen deck 60/90: Output: 0-60/90 and > 60/90 mm / Length 4500 mm / Width 1450 mm / Screen area 6.5 m² / Position 11° incline / Star shafts 17 pieces / Star diameter 340 mm / Star width 55 mm / Center distance 266.5 mm / Cleanstar cleaning elements / motor 2 x 4 kW / Adjustable via frequency inverter - Drive motors 50 Hz: motors for driving the screen deck / 2x 4 kW 50 Hz - Dosing roller: width 1560 mm / diameter 215 mm / drive 3 kW drum motor - FKAB with magnetic drum: Center distance 6200 mm / Belt width 1000 mm / Installation position 30° inclined / Belt type profiled, 15 mm chevron / 3.0 kW motor, v=2.2 m/s / Usable discharge height 3500 mm - 3950 mm / Multi-pole magnetic drum in permanent version / incl. discharge chute - Over-grain discharge conveyor: Center distance 6200 mm / Belt width 1000 mm / Installation position 30° inclined, 220° pivoting / Belt type profiled, 15 mm chevron / motor 3.0 kW, v=2.2 m/s / Usable discharge height 3600 mm - 4050 mm Transport dimensions approx. 8176 x 2466 x 2600 mm LWH Weight approx. 9200 kg Sale on behalf of customer, ex location near 85456 Wartenberg, without dismantling, transport and assembly Subject to errors in the description and price Dismantling, transport and loading by us optionally possible To avoid possible misunderstandings, an on-site inspection is possible and recommended by appointment Sold as is Technical details, condition description, year of manufacture and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale No warranty is given for used machines, the following applies: “purchased as viewed” Images and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or shipping Terms of delivery: ex location

Condition: used, Year of construction: 2002, overall weight: 10,000 kg, rotor length: 2,000 mm, power: 90 kW (122.37 HP), rotational speed (max.): 80 rpm, Lindner Micromat MS 2000 Csdpfjwtbyrsx Abrehd Drive motor: 90 kW, 400 V/50 Hz Control cabinet: complete star/delta Rotor speed: at 50 Hz approx. 80 rpm Rotor knives: 80 pcs. new Rotor knife shape: blunt knife 60 mm Filling opening: LxW 2030 x 1650 mm Rotor length: 2030 mm Rotor flight circle: 560 mm Scraper comb: yes Counter knife: yes Hydraulic unit: complete Sieve cassette: screens as per customer request Total weight approx. 10.5 t Dimensions LxWxH mm: approx. 4520 x 2970 x 2660 mm Inspection and test run possible by appointment. Incl. hopper Delivery time: immediately

Condition: good (used), Year of construction: 2009, In different assemblies, several parts. Interface Module Panel Manufacturer. SIEMENS S7 Cedpegblhvofx Abrohd Typ: X1 Profibus-DP ET200S Panel consist of the following pieces: 1 - X1 Profibus-DP ET200S 1 - IM 151-1Standard 6ES7-151-1AA04-0AB0 1 - PM-E 6ES7 138-4CA01-0AA0 4 - 4DI 6ES7 131-4BD01-0AA0 3 - 4DO 6ES7 132-4BD01-0AA0 1 - 1SI 6ES7 138-4DF01-0AB0

Condition: used, CNC 5-Axis HMC – Horizontal Machining Center, Milling Center, Manufacturing Center Manufacturer: LICON Model: Liflex 1266 PC B1 Year of construction: 2016, Commissioned: 2017 Equipped with SIEMENS 840D SL (Solution Line) CNC path control, with 5 simultaneously controlled axes Travel paths X: 1200 mm, Y: 660 mm, Z: 650 mm A-axis as swivel bridge +/– 135° (270°) B-axis 360° continuous Axis acceleration X + Y-axis 6 m/s² Axis acceleration Z-axis 9 m/s² Feed force X + Y-axis 7500 N Feed force Z-axis 10000 N Positioning tolerance (X/Y/Z) 0.008 mm A-axis swivel speed 180° rotation in 4 sec. Interference diameter on the swivel bridge max. 1400 mm Transport load on the swivel bridge max. 700 kg Tool holder HSK 63 Spindle speed max. 12,000 rpm, stepless Spindle power 37kW at 40% duty cycle Spindle torque at 40% duty cycle 85 Nm Maximum spindle torque 100 Nm Tool change time (chip-to-chip) approx. 3.7 sec. Tool diameter with adjacent slots occupied Ø 140 mm Tool diameter with adjacent slots free Ø 250 mm Maximum tool length 400 mm Maximum tool weight 20 kg Power supply 400 Volt, 50 Hz Connected load 80 kVA Compressed air connection 5-8 bar - LIFLEX MSP 80/63/85/12,000 motor spindle (output 37kW/40% duty cycle) with liquid cooling and recooling unit - 2-axis rotary tilting table LICON as B- and C-axis, with hydraulic axis clamping - Zero-point clamping system on the swivel axis turntable - Dual pallet changer, without pallets (these need to be newly sourced) - Media transfer of 5 single-action pressure lines for oil or air, for workpiece clamping on the pallets Hydraulic functions from 30-150 bar, with pressure monitoring (controllable via M-functions) - Tool changer with 30 tool positions, disc turret type - Machine designed for dry machining with minimal quantity lubrication (MQL) system - MQL-TSC, internal MQL lubrication supply through the spindle - Scraper belt chip conveyor, discharge height 1150 mm - Licon ECO-Mode (energy-efficient aggregate operation) - Direct linear measurement system on all axes - Operating hours (control voltage on) ≈ 7,500 h Chedpfx Ast Ac Efebrsd Space required for operation L x W x H 9,000 x 5,000 x 3,800 mm Space required for transport L x W x H 6,100 x 4,400 x 3,600 mm Base machine weight approx. 21 tons Total weight: approx. 24 tons Very good condition

Condition: new, Year of construction: 2024, operating hours: 15 h, functionality: fully functional, type of input current: AC, input voltage: 240 V, measuring range X-axis: 580 mm, measuring range Y-axis: 300 mm, measuring range Z-axis: 200 mm, total width: 579 mm, total length: 916 mm, total height: 844 mm, overall weight: 45 kg, workpiece weight (max.): 50 kg, VL-770 3D measuring system with motorized rotary table Ø500mm - VL-770 measuring head - VL-700 control unit - 500mm object table VL-750 - Measuring range with composition up to Ø500mm or 580x300mm - Cover (light shielding) - Software package (German) Csdpovzqp Hofx Abrohd - Calibration plate - Software module for form and positional tolerances - Software module for CAD conversion Full description available in the brochure