Tank

BERCLAZ + METRAILLER 6000 L

Condition: used, Year of construction: 2004, Pressure 630 t stroke 800 mm distance between columns 2600 mm Distance table/ram, max. stroke up, adjustment up 1500 mm Table surface area 2500 x 1300 mm pressure of drawing cushion in table 300 t Die cushion stroke in table 300 mm Ram surface 2500 x 1300 mm Ljdpfx Afjv Svaroaehc Side window 1040 mm feed down 600 mm/s feed up 360 mm/s working feed 14 - 42 mm/s power requirement 145,0 kW Weight 85,0 t dimensions (WxDxH) 4,2 x 4,0 x 7,8 m height over floor 6,80 m height beneath floor 1,0 m Demonstration machine from technical university with approx. 920 operating hours! Mint condition! permitted for manual loading according to the CE-norm with oil-hydraulic drive, controllable dependent on pressure/time and way, upper and lower stroke limitation, light-guard (Sick) on front and back, hydraulic drawing cushion in table with ejector function, hydraulic cutting impact cushioning, mechanical depth stop via 4 motor-adjustable spindles, hydraulic ram interlocking, two-hand operation 2 tool changing consoles, 4 hydraulic ball roller tracks, 4 dampening elements

Year of construction: 2001, operating hours: 123 h, condition: ready for operation (used), machine/vehicle number: 123, Metal silo for storage of woodchips, etc. Technical description: silo DM: 5m Lodpfx Aeftdv Uofajhc Height: 8 m with outfeeding unit (screw conveyor connection to output) Cappacity: 42 m3 With outfeeding transport screw conveyor to the top of the silo building. Already dismountled, visit possible by appointment at our warehouse H-2013 Pomáz/Hungary.

Condition: used, Year of construction: 2001, Wood dimensions to be processed: Input lengths min/max 500 - 6500 mm Full optimization up to max. 1500 mm Input widths min/max 40 - 300 mm Input thicknesses min/max 15 - 120 mm Wood cross-sections max. 300 x 40 mm max. 200 x 120 mm Fixed lengths after sawing min. 510 - 2800 mm Special application: Cutting blocks, length min/max. 100 - 200 mm (Caution: Multiple block lengths at the sorting line; blocks are transported to the end of the sorting line and fall into the customer's grid box). Cutting/cutting tolerance +/- 0.8 - 1.5 mm (for wood types with minimal resin content and an even surface. Tolerance up to 1 m fixed length, max. tolerance for longer pieces up to 2.5 m). Thickness tolerance +/- 3 mm. Curvature of the wood in all directions: max. 10 mm per meter in length. Wood types: soft or hardwood. System performance: Feed speed, continuously adjustable up to max. 230 m/cutting cycle 0.6 - 1. To obtain the practical output per day, an effectiveness factor dependent on the customer's production conditions must be calculated. Infeed and saw height: 900 mm (placed on customer's platform, saw requires concrete base). Sorting working height. 2000 mm Connection values: Total electrical connection value approx. 18 kW Operating voltage 380 Volt / 50 Hz Voltage fluctuations max. 5% Air consumption approx. 1200 NL/operating pressure approx. 8 bar Extraction speed approx. 30 m/nd Color pebble gray RAL 7032 and blue NCS 5030-R 80 B POSITION OVERVIEW: Item 1 Infeed and marking station with 1 side support table, adjustable 1 table as stop edge Item 2 Support roller without drive, front side in front of sheet metal table for easier feeding Item 3 Length measuring station with built-in fluorescence camera for detecting error markings Item 4 Automatic width measurement, contactless Item 5 OptiCut 304 optimizing cross-cut saw - right-hand version with built-in waste chute including equipment package for large wood cross-sections Graphic input terminal (16 x 40 characters, Numeric keypad) with software package for optimization and system control. Available for processing: - max. 16 product groups - max. 8 grades per product group - max. 200 fixed lengths per product group Item 6: Outfeed conveyor as sorting station with drive unit, length 7500 m Item 7: 2 ejectors mounted on the outfeed conveyor Ledpfx Aow Sy T Hjfashc Storage location: Nattheim

Condition: used, Year of construction: 2001, High-performance optimizing cross-cut saw GRECON DIMTER OptiCut S75-4 with defecting mode. This machine is ideal for precise solid wood cutting, featuring automated detection and elimination of material defects. Lhedpfxjwtgcxe Afajc Technical specifications: Model: OptiCut S75-4 Manufacturer: GreCon Dimter Year of construction: 2001 Commission no.: 0682-10 Rotary current: 400 V / 50 Hz Control voltage: 230 VAC / 24 VDC Nominal output: 11 kW Fuse protection: 25 A Condition: used

Condition: new, Very powerful industrial polisher Two versions: - Motor ----- 900W - 230V - 1 Phase - Motor ----- 900W - 400V - 3 Phase Polishing discs D x W ----- 200 x 20 mm Speed ----- 2850 rpm Shaft size -----16 mm Packing dimensions ----- 620 x 320 x 340 mm Lhjdpsga Twxjfx Afaoc Weight ----- 20 kg Including mounted hard and soft polishing wheel OPTION * Support box Price: € 99,00 ex vat

Condition: excellent (used), Year of construction: 2014, Viessmann Vitoplex 700kw Year: 2014 Type: SX2A Output:700Kw Viewing only by telephone arrangement! Preferential sale to dealers, traders or export. All information without guarantee, subject to errors and prior sale. R2ru7mxt2v Lhodpstu T I Usfx Afaoc The seller assumes no liability for typing and data transmission errors. Of course we also take care of all formalities Loading possible Request more information

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C Lsdpewp Rqfefx Afaohc • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: used, functionality: fully functional, Sawmill for sale: The line starts with a Bongioanni bandsaw and a Costa Multiprisma sawmill. Due to their design, they are suitable for processing both soft and hard hardwoods. The price includes the lines, additional machines (dust extraction, recycling machines) as well as the necessary saw blades and spare parts. The sawmill can be viewed in Cegléd, Hungary, by prior arrangement. Line 1: - 1-1 Log yard with single-sawn saw - 1-2 Costa Multiprisma: 280 two-axis prism saw with log turner, 60-80 m3/8 hours depending on the wood species and diameter - 1-3 Roller conveyor with discharger - 1-4 Custom-built cross-cut saw: for single-size cutting, with size adjustment option. - 1-5 Conveyor belts for transporting lump waste. - 1-6 Grinder (drum) - 1-7 Grinder conveyors: screw conveyor, bucket elevator, chute, direct loading onto wagon/truck 2nd line: - 2-1 Log store with splitter - 2-2 Log conveyor track, with drop-off - 2-3 Intermediate log store with splitter - 2-4 Bongioanni log splitting bandsaw and trolley, with 1300 digital control, multiple size presetting options, sheet deflection indicator, laser ruler, 25-45 m3/8 hours; depending on the type of wood, diameter and cut pattern - 2-5 Roller conveyor with ejectors - 2-6 Cross conveyor with singler - 2-7 Storti TGS-78 cutting saw: with digital control, three saw units for up to double the size of the cut - 2-8 Roller conveyor with graders - 2-9 Intermediate prism magazine - 2-10 Roller conveyor - 2-11 Costa Leopard II. series cutter, with 2-axis automatic feed and power control - 2-12 Roller conveyor with ejector and sorting table - 2-13 Conveyor belts for lump waste Lsdpfx Aev Hm T Sefashc - 2-14 Grinder (drum) - 2-15 Grinder conveyors: screw conveyor, bucket elevator, rédlers (walking floor truck loading option) 3. Auxiliary machines: - 3-1 E. Gillet slitting band saw, associated conveyors, manipulator, feed mechanism - 3-2 Joiner's band saw (800) - 3-3 Pallet cube cutting machine (starboard) - 3-4 SOCOLEST Valdoi double edge circular saw, with conveyors, cutting circular saw - 3-5 VEB STANDARD single-axis formatting circular saw - 3-6 STVO single-axis formatting circular saw machine

Condition: good (used), Year of construction: 2006, I sell the automatic pneumatic end cutting saw Weinig Grecon Dimter Opticut 200 Elite Year 2006 Motor power 7,5kW Input table automatic feeding 4,10m (throughfeed system) Outut table automatic 6 pcs. kickers on right outfeed table Optimising with mistakes deffect reading and automatic cutting sequence modes. Available immediately. CE version. Documentation included. Lhedpfx Afextxi Ijasc

Condition: used, Year of construction: 2007, pressure 315 t distance between columns 1750 mm stroke 700 mm distance table/ram, max. stroke up, adjustment up 1200 mm table surface area 1600 x 1500 mm pressure of drawing cushion in table 125 t stroke of drawing cushion in table 200 mm die cushion area 1200 x 1400 mm table height over floor 750 mm ram surface 1640 x 1500 mm power requirement 55,0 + 11,0 kW weight 29,5 t dimensions (WxDxH) 3,2 x 4,5 x 5,8 m Height above floor 5,1 m year of manufacture 1983 - 2007: modernization of electrical control (Siemens S 7) permitted for manual put-in according to the CE Regulations with oil-hydraulic drive, hydraulic drawing cushion in table, hydraulic cutting impact cushioning Ledjvuukbopfx Afajhc can be offered without putting into operation, with putting into operation in given condition or alternatively with new control Siemens S 7-1500 F