Baler HBK 100 45 kW

Bollegraaf Recycling Solutions B.V. Baler HBK 100 45 kW

Condition: used, Year of construction: 1996, charge load 135 liter 1220 mm tank diameter / tank height 1.220 / 1035 mm 304 mm motor capacity 0,75 kW Podpfxjwcg Ere Ah Ujrf motor speeds: 1500 U/min voltage 400 V weight of the machine ca. 600 kg dimensions of the machine ca. 1,38 x 1,28 x 1,04 m Dryer - Serial-No.: 15772 / 96-08 - Machine ON: 44.854 h - Heat unit

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Prjdpfxjvwlqqo Ah Uof Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2024, condition: new, Overview - of the different variants *Not every position is required: Optional: -Bale shredder MHB from 24.990 € net -MHZ straw mill from € 7,980 net -Special hopper 970 € net -Cyclone from € 3,750 net Prsdpfx Ahjff Sbis Uof -Sheet metal silo demonstrator with discharge (only sketched in the picture) *optional, if you want to load with the wheel loader Unit price net from € 14,750 - Demonstrator -Dedusting auger - length approx. 4 m 4 sieves are mounted on the underside, which are extracted. Unit price net from: 9.750 € - Extraction parts / hoses flat rate 945 € net - Complete control system Net unit price: € 2,750 -Demonstrator extraction unit MMJET 160 Demonstrator, with cleaning Connection 160, fan 2,2kw air capacity 1850m³ /400 V Automatic compressed air cleaning Unit price net from: 6.950 € -Baler B 400 Bales approx. 400x400x800 (height adjustable) Up to 30 bales per hour with + - 20 kg from 59.995 € net *A reference system (baler) is located in zip code: 64579 Gernsheim Technical data: Bale size (WxDxH): 400 x 400 x 800 (height can be adjusted on request) Bale weight +/- 20 KG (depending on material) Capacity: approx. 30 bales per hour Storage container approx. 0.7m³ capacity Filling level sensors for min./max. filling level in the container Hydraulic pre-compressor Hydraulic compression ram Hydraulic unit, valve block with oil tank Pump 18.5 KW / 50 liters Rollers in the bale chamber for easy bale push-off Dimensions (l x w x h) 3105x2830x2455 mm Weight approx. 1500 KG mütek baling presses / wrapping machines are designed for the production of bales from a wide variety of materials such as shredded micanthus or elephant grass, wood chips, sawdust and shredded straw. straw. The machine is characterized by a robust design that guarantees consistent quality in continuous operation. quality in continuous operation. The baler compacts the material filled into the storage container without the addition of binding agents and packs the material into plastic bags. The volume of the material can be considerably with the baling press. The volume reduction rate depends on the material. The maximum material moisture content must not exceed 18 % Atro. The container of the mütek baler can be fed automatically or manually and has a volume of approx. 0.7 m³. volume of approx. 0.7 m³. Containers with a larger volume or with an attached suction and filter system as a complete disposal unit are also available. In addition to automatic filling via deduster, mütek also offers filling by means of screw conveyors. With both variants, automatic automatic dedusting is possible. mütek baling presses are equipped with a control cabinet for the control system. In the standard version, the dimensions of the bales (width x depth x height) are 400 x 400 x 800 mm. However, the height can be adapted to your requirements on request. The following advantages arise in the production of bales: - simple and safe storage - No loose dust - Minimization of the storage volume - Low transport volume *Requirements for source material: - dry (max. 30 % ATRO) - Maximum length 35 mm

Year of construction: 2003, operating hours: 43,000 h, condition: repair required (used), machine/vehicle number: HBC 140 2x75kW 2003 (W230-005), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2003 Hardox bottom floor plate only Plastic valve Anti-rat cabling Hours 43.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. Podpfx Ajkcgynoh Uorf General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: ready for operation (used), Baler Hsm vk 42/1200 fully automatic Pressure force: 42 tons Prodpfx Ahsra Nrxs Uof Beam dimensions: 700 x 800 x 600 - 1200 mm Beam weight: approx. 450 kg Press length approx. 7 meters press weight approx. 6000 kg tying 4 x wire automatically

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Predpfsvf E Avox Ah Uef Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: W230-028, pressing force: 80 t, warranty duration: 24 months, pressure: 250 bar, power: 45 kW (61.18 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler. This is a baler HBC80 (45kW) with crosswires. Pedpfetvat Tsx Ah Usrf At the time of writing this baler is being completely refurbished in our refurbishment workshop. This refurbishment takes place on the basis of the very strict Bollegraaf OEM Refurbishment Guidelines. After refurbishment, this baler is sold with a 2-year warranty.

Condition: good (used), Manufacturer: Haver & Boecker Prodpfxsv Sz Tdj Ah Usf Documentation available Mechanical conversion from 50 kg to 25 kg bags in 1999 Control system: Siemens S7 Upgraded to the latest standard with spare parts support in 2015 Supported bag types: Quicklime, hydrated lime, cement, gypsum

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: HBC 140 2x75kW 2001 (210-008-01), pressing force: 155 t, bale weight: 1,500 kg, pressure: 250 bar, power: 150 kW (203.94 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Pjdpfx Ahotvau As Uerf Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: excellent (used), Year of construction: 2004, Clamping force: 25/35 tons Opening stroke: 200 mm Mould height: 150-300 mm Clamping platen daylight: 350-500 mm Podouykh Dopfx Ah Uorf Tie bar daylight: 221 mm Mould clamping plattens (b x h) : 342 x 250 mm Ejector stroke: 60 mm Screw diameter: 25 mm Screw stroke: 100 mm Injection volume: 70 cm3 Shot weight: 59 g Injection pressure: 1040 bar Working hours: 34.748