Used lowboy semi-trailers / low loaders for sale (275)

Condition: new, maximum load weight: 45,250 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete inventory of vehicles available for immediate and short-term delivery on our website. Excerpt from the equipment list. Full specifications available upon request. Chassis, stepped: * Special steel frame made from high-strength fine-grained steels, electrically welded at connection points * Generously dimensioned outer frame. 4-axle configuration * Wheel covers over the axles with spray suppression * All steel parts sandblasted * Side underrun protection made of anodized aluminum mounted * Increased point load approx. 30,000 kg over approx. 4,000 mm * Special construction in the stepped area for the longest possible low-bed length in combination with AluLeg drop supports instead of telescopic support legs, maximum rear swing clearance of the tractor unit approx. 2,100 mm Special body with rear stake extension: * DINKEL – special body * Self-supporting aluminum roof beam / profile approx. 120 x 100 mm, sliding roof with plastic flaps * Rear stakes extendable for loading/unloading up to approx. 4,200 mm * Three sliding stakes per side with elastic relief * Additional intermediate stake lockings in roof beam and parked position, via pull cable and spring bolt * DINKEL – mechanical lift roof, height-adjustable * Lift roof height approx. 400 mm, operable from both sides or one side without opening the opposite side * Additional height adjustment of approx. 480 mm in approx. 40 mm increments by adjusting the stakes * Front cover at bulkhead for driving operation under the tarpaulin up to a total height of approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminum slats on the side, 450 pockets below, four rows of single pockets above. Only three rows of slats in the raised platform, spacings evenly distributed Floor: * Approx. 27 mm special waterproof bonded beech phenolic plywood, rough surface * Steel sheet in the wheel well area. Suitable for forklift traffic as per DIN standard * Outer frame flush with deck surface Brakes: * WABCO air brake system with EBS according to EC Directive 71/320, including PREV (Parking-Release Safety Valve) * Spring-loaded brake cylinders as parking brake * WABCO Smart Board with mileage counter and axle load display * Including WABCO tire pressure monitoring system Axles: * 4 x 10,000 kg SAF with drum brakes in low-loader design * Air suspension with lift and lower device, total lift approx. 230 mm * Third and fourth axles as friction-steered trailing axles with electric and mechanical lock Twin tires: * 235/75 R 17.5, 16-ply. Make of our choice, including spare wheel holder * Without spare wheel Lighting: * According to EU regulations, including LED side marker lights * Position lamps in LED design * 2 additional reversing lights * 2 work lights on the inside front wall, upper section Paintwork: * Chassis and body in one color, RAL 3002 carmine red * Intermediate stakes, axles KTL-coated black * Corner stakes hot-dip galvanized Hedpewx Dbisfx Ab Uofr * Plastic parts black * Galvanized parts unpainted * Rims in factory silver Special equipment included: * 15-pin electrical supply cable * Air suspension in ECAS design, operated on the trailer * Oversize signage front and rear in galvanized, infinitely telescopic design with installed marker lights, including sockets for rotating beacons (small signs) * Additional external release for sliding roof frame lock * 4 stake adapters for special outer frame profile, to lock intermediate stakes as needed * PVC sliding tarpaulin, color similar to RAL 9

Condition: used, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 06/2021, next inspection (TÜV): 02/2025, loading space length: 7,000 mm, loading space width: 2,530 mm, Equipment: ABS, * 2-axle VEGA * Loading ramp * Air suspension * Tyres: 205/65R17.5 Hjdpexu Ti Ejfx Ab Ujfr * Trax axles * Unladen weight 5750 kg ----Internal vehicle number: 11502-----Subject to errors & prior sale

Condition: used, empty load weight: 7,300 kg, maximum load weight: 37,700 kg, overall weight: 45,000 kg, axle configuration: 3 axles, first registration: 03/2019, suspension: air, tire size: 235/75R17,5 --/140J, color: other, gearing type: other, front tire size: 235/75R17,5 --/140J, rear tire size: 235/75R17,5 --/140J, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Reinforced design, length of high bed approx. 4,180 mm, length of low bed approx. 9,400 mm, loading height approx. 900 mm, 12 x stake pockets in the outer frame, 3 x cross stake strips, 14 x lashing eyes, 4 pairs of container locks for, 2 x 20 ft. ISO containers or 1 x 40 ft ISO container, , --  Misprints, errors and changes reserved, sample images --, More data at: !, More Details: ! Hfodjxuprpopfx Ab Uor

Condition: used, empty load weight: 11,800 kg, maximum load weight: 36,200 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 03/2022, total length: 2,550 mm, suspension: air, tire size: 245/70 R17,5, Equipment: ABS, | Faymonville Telemax F-S43 low loader | 3 axles steered by remote control | Heavy duty lashing points | SAF axles | extendable | Stake pockets | Tires: 245/70 R17.5 | Total weight: 48,000 kg, payload: 36,200 kg | 13,500mm+7,900mm+8,100mm | Subject to error, input mistake and prior sale. Hfjdpswm I Ipjfx Ab Uor

Condition: used, empty load weight: 6,560 kg, maximum load weight: 18,440 kg, overall weight: 25,000 kg, axle configuration: 2 axles, first registration: 09/2017, loading space length: 13,700 mm, loading space width: 2,540 mm, loading space height: 850 mm, wheelbase: 7,500 mm, color: blue, gearing type: other, driver cabin: other, Equipment: ABS, additional headlights, compressed air brake, * German semi-trailer * Very good visual condition, see photos * 2-axle low loader, Jumbo TO 152 DE * Loading platform: Length 13,700 mm x Width 2,540 mm * Loading height approx. 850 mm * Stake pockets * Multilock system * Wooden loading floor * Winch with cable remote control 15,000 lbs * Long aluminum ramps, 3,000 x 400 mm, laterally movable * ROR axles * Air suspension * Haacon spindle supports * ABS + EBS * Work lights * Spare wheel * Toolbox * Brake drums * Wheelbase 7,500 mm + 1,250 mm * Gross vehicle weight possible: 27,200 kg * Unladen weight: 6,560 kg * Payload possible: 20,640 kg If a new general inspection (TÜV) is required, we will be happy to provide you with an offer from our partner workshops. Our offer is generally WITHOUT new general inspection (TÜV), without new DGUV, without new SP, without new UVV. You can find more trucks on our website at We speak the following languages: German, English, Polish, Turkish Hodpexu Nnwjfx Ab Ujfr Note: We offer and strongly recommend viewing and inspection of the goods to avoid any misunderstandings regarding condition and suitability. Viewing and inspections are possible at any time by prior arrangement and are expressly encouraged. All information is provided without guarantee. We do not accept liability for errors or incorrect information in this offer. Buyers are required to independently satisfy themselves as to the condition and specification of the goods/vehicles. Subject to change, prior sale, and errors.

Condition: new, empty load weight: 5,500 kg, overall weight: 19,500 kg, axle configuration: 1 axle, loading space length: 11,800 mm, loading space width: 2,550 mm, loading space height: 1,100 mm, suspension: air, tire size: 215 75 17,5, Equipment: crane, 1x SAF or BPW axle Total weight: 19,500 kg Payload: 14,000 kg Empty weight: 5,500 kg Total length: 12,800mm + 1500mm Brake system: Wabco 2S-2M Hedpfx Abekqmuue Uofr Electrical system: Aspöck Systems Air suspension Hydraulic rear extension in full width 2550mm and length 1500mm Semi-trailer completely galvanized / galvanized (100% galvanized / 100% galvanized) Tire size: 215/70 R 17.5 Tire brands: Pirelli, Goodyear, Fulda, Continental. 5th Wheel Height: approx. 1050mm - 1150mm (other saddle heights also possible) Hydraulic winch 8ton with remote control with pulleys 24v 4.5KW electro-hydraulic motor Steel ramp: 2 pieces Changes possible according to customer requirements Painting freely selectable / free of charge All documents COC, Tüv, etc. available for approval.

Condition: used, maximum load weight: 57,900 kg, overall weight: 73,000 kg, axle configuration: > 3 axles, first registration: 06/2024, next inspection (TÜV): 07/2026, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpts from the equipment list. Complete specifications available upon request. Gooseneck: * Gooseneck in SNT design for optimized loading platform length, approx. 3,700 mm in length * Rear of the gooseneck with bevel of approx. 1,000 mm x 10° * Technical fifth wheel load: 30,000 kg Suitable for tractor units: 4 x 2, 6 x 2 and 6 x 4 Loading platform: * Telescopic loading platform, approx. 8,800 mm in length, with rear ramp approx. 500 mm x 10° Axles and suspension: * BPW axles and suspension * 1st axle steered, equipped with electromagnetic reverse lock; all other axles hydro-mechanically forcibly steered * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tyres: * 235/75 R 17.5 3PMSF twin tyres, load index 143/141J (144/144F) Brake system: * WABCO EBS-E braking system, compliant with EU regulations Paintwork: * Trailer colour: RAL 3002 Carmine Red Accessories included: Hfsdoxuypropfx Ab Uer * Removable steel front wall, approx. 400 mm high * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) * 3 kW electro-hydraulic unit for controlling hydraulic operations, except for hydraulic winches; without installation of power connections on the tractor unit * Stowage position on the gooseneck for warning signs when not in use * 1 mounting adapter for spare wheel in front of the gooseneck front wall (without spare wheel) * Outer carrier on the gooseneck with fixing holes for bolt-on lashing rings. First hole approx. 200 mm from the front, then at approx. every 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of horizontal lashing rings in the rear area of the gooseneck (LC 10,000 daN) * On the gooseneck, 1 pair of removable ALU sidewalls, approx. 400 mm high, anodised * On the gooseneck, 1 removable ALU rear wall, approx. 400 mm high, anodised * Approx. 40 mm thick hardwood flooring over the gooseneck, checker plate over the kingpin * 2" kingpin * Mechanical landing gear with 2-speed gearbox and crank, JOST Modul B * On the loading platform: continuous and axially interrupted approx. 50 mm thick hardwood flooring * Platform locking with conically welded locking profiles approx. every 500 mm * Slotted holes for hook-in and repositionable bridging elements: at front of loading platform * 1 sliding intermediate table, approx. 300 mm wide, for the high cross-section telescopic tube with checker plate surface; front and rear with slotted holes for hook-in and repositionable bridging elements * 1 pair of lashing rings on the front crossmember (LC 10,000 daN) * 7 pairs of recessed lashing rings in the outer frame of the loading platform, foldable outwards (LC 10,000 daN) * Extendable galvanised platform widenings by approx. 230 mm per side (without wooden planks) * 1 pair of mechanical rear supports * Rear steering from front and rear operable via cable remote control with buttons, with single-track axle alignment, without installation in tractor unit * Cable (approx. 35 mm², approx. 3.5 m long) with connectors (NATO-NATO) between trailer and tractor unit for supplying the electro-hydraulic unit and/or electric winch * 2 additional pairs of bolt-on lashing rings (LC 5,000 daN) * 1 one-piece INOX tool box, approx. 2,480 x 340 x 390 mm (L x W x H), straight design, with 2 external side doors and 1 top lid, located behind the front wall

Condition: used, empty load weight: 18,500 kg, maximum load weight: 59,200 kg, overall weight: 77,700 kg, axle configuration: > 3 axles, first registration: 10/1978, loading space length: 9,650 mm, loading space width: 3,150 mm, loading space height: 1,100 mm, total height: 142,000 mm, suspension: steel, tire size: 8,25 R 15 PR 18, color: green, mileage: 1,001 km, gearing type: other, driver cabin: other, Vehicle location: in transit, 6 axles, Kässbohrer axles, leaf suspension, forced steering, lashing eyes, 2-part loading ramps, front support, twin tires Body: 600mm ramp width, 1950mm between ramps, 6 axles, 3rd, 4th, 5th, and 6th axles hydraulically forced steered, fifth wheel height 1,550mm loaded, kingpin 3 ½", 6 x 10.55t axles, total length 14,200mm. Hedpfxsxwa Uyj Ab Uofr All information provided without guarantee, as the vehicle is in transit! ACCESSORY DETAILS WITHOUT GUARANTEE; subject to change, prior sale, and errors!

Condition: new, empty load weight: 7,200 kg, maximum load weight: 31,800 kg, overall weight: 39,000 kg, axle configuration: 3 axles, suspension: air, tire size: 235/75 R 17,5, color: other, gearing type: other, front tire size: 235/75 R 17,5, rear tire size: 235/75 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Length high bed approx. 4,180 mm, length low bed approx. 9,400 mm, front wall approx. 800 mm high, 14 x stanchion pockets in the outer frame, 8 x stanchions, 3 x cross stanchion rails, 24 x lashing eyes, 4 pairs of container locks, , , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Hfodpfx Aexrmtrob Uor

Condition: new, empty load weight: 8,785 kg, overall weight: 33,000 kg, axle configuration: 3 axles, loading space length: 13,311 mm, loading space width: 2,500 mm, total length: 2,600 mm, total width: 4,000 mm, total height: 14,000 mm, suspension: air, tire size: 385/65 R22.5, Equipment: ABS, | Krone Cool Liner Multitemp Deep-Freeze Refrigerated Semi-Trailer – New Vehicle | Double-deck without crossbeams – beams available on request | Flower width, lift axle | Krone axles with disc brakes | Toolbox | Spare wheel holder | ThermoKing SLXi refrigeration unit | Tyres: 385/65 R22.5 | Diesel operating hours: 3h | Trailer from current production!!! | Subject to errors, input mistakes, and prior sale. Hfsdpfxewl Rpys Ab Uor

Condition: used, empty load weight: 9,480 kg, maximum load weight: 31,520 kg, first registration: 03/2020, next inspection (TÜV): 04/2024, total length: 11,500 mm, total width: 25,500 mm, total height: 38,000 mm, suspension: air, tire size: 245/70 R 17.5/10mm, wheelbase: 1,800 mm, front tire size: 245/70 R 17.5/10mm, operation weight: 41,000 kg,

Condition: used, maximum load weight: 23,000 kg, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 04/2025, loading space length: 9,200 mm, loading space width: 2,550 mm, total width: 2,550 mm, Year of construction: 2025, Equipment: ABS, GVN 3GVN29 OVERSIZE PLATFORM *KOC*LIFT*P ----VEHICLE HISTORY * NEW VEHICLE * VIDEO AVAILABLE ON REQUEST VEHICLE EQUIPMENT TECHNICAL DATA AND EQUIPMENT SHEET VEHICLE TYPE: * GVN TRAILER – 3-AXLE EUROPEAN MODEL TRADING DESIGNATION: * 3GVN29 ----WEIGHT SPECIFICATIONS CURB WEIGHT * 13,000 KG DISTRIBUTION OF THIS WEIGHT ON THE AXLES 1ST AXLE: 3,653 KG 2ND AXLE: 3,653 KG 3RD AXLE: 3,653 KG ACTUAL VEHICLE WEIGHT * 13,000 KG TECHNICALLY PERMISSIBLE MAXIMUM GROSS WEIGHT * 58,000 KG TECHNICALLY PERMISSIBLE MAXIMUM AXLE LOADS 1ST AXLE: 12,000 KG 2ND AXLE: 12,000 KG 3RD AXLE: 12,000 KG TECHNICALLY PERMISSIBLE MAXIMUM WEIGHT ON AXLE GROUPS 1ST GROUP: 36,000 KG MAXIMUM GROSS WEIGHT FOR REGISTRATION PURPOSES * 35,500 KG MAXIMUM AXLE LOADS FOR REGISTRATION PURPOSES 1ST AXLE: 8,000 KG 2ND AXLE: 8,000 KG 3RD AXLE: 8,000 KG MAXIMUM WEIGHT ON AXLE GROUPS FOR REGISTRATION PURPOSES 1ST GROUP: 24,000 KG TECHNICALLY PERMISSIBLE MAXIMUM STATIC LOAD ON COUPLING POINT * 22,000 KG TECHNICAL MAIN DIMENSIONS (COC) * OVERALL LENGTH: 13,050 MM * LOADING PLATFORM LENGTH: 9,200 MM * VEHICLE WIDTH: 2,550 MM * OVERALL HEIGHT: 3,000 MM * PLATFORM HEIGHT: APPROX. 910 MM * NUMBER OF AXLES: 3 * TIRE SIZE: 235/75 R17.5 * SUSPENSION: AIR SUSPENSION * COLOR: RAL 5011 ----EQUIPMENT LIST * EXTENDED GOOSENECK * FIXED GOOSENECK * STEEL FRONT WALL * 2 REMOVABLE SIDE DOORS MADE OF STEEL * 1 REMOVABLE REAR FLAP MADE OF STEEL * FRONT STORAGE COMPARTMENT * FRONT STORAGE COMPARTMENT UNDER NECK * LOADING PLATFORM ON THE GOOSENECK LOADING PLATFORM * HIGH-STRENGTH S355 STEEL * PLATFORM EDGES CLAD WITH WOOD * SURFACE COVERED WITH STEEL PLATE * 14 SIDE EXTENSIONS EACH +230 MM * 14 FORGED STEEL LASHING EYES, EACH 16 TONNES * EXTENDABLE PANEL FOR OVERSIZE WIDTH * OVERSIZE WIDTH MARKER * WARNING SIGN FOR OVERSIZE WIDTH * ATTACHMENT POINTS * ADDITIONAL SUPPORTS * PRESSURE GAUGE AXLES AND SUSPENSION * 3 AXLES * OSMAN KOC AXLES, IDENTICAL TO BPW * STEERED 3RD AXLE * LIFT AXLE: 1ST AXLE * TWIN TYRES ON ALL AXLES * FULL AIR SUSPENSION ON ALL AXLES * 1ST LIFT AXLE, DRUM BRAKES BRAKE SYSTEM * EBS SYSTEM WABCO ELECTRO-PNEUMATIC EC STANDARD * AUTOMATIC REVERSE ALIGNMENT OF STEERED AXLE * DRUM BRAKES ON ALL AXLES TYRES AND RIMS * TYRES 235/75 R17.5 * SPARE TYRE: YES * WHEELS: 12 * MAX. SPEED: 80 KM/H * RIMS: 6.75X17.5 STEEL SILVER-GREY * SPARE WHEEL AVAILABLE Hedpfxsw Dlqij Ab Uofr COATING * 2 COATS EPOXY PRIMER, EACH 100 MICRON * MIN. 100 MICRON 2K ACRYLIC PAINT * COLOUR: RAL 5011 ELECTRICS AND LIGHTING * 24 VOLT SYSTEM TO EC STANDARD * WATERPROOF AND FROST-PROOF CONNECTIONS * SIDE AND MARKER LIGHTS * 6 REARLIGHTS, 3-FUNCTION * 2 REVERSING AND WORK LIGHTS * 2 INDICATORS * 2 NUMBER PLATE LIGHTS * 1 BEACON * 2 TRIANGULAR REFLECTORS * REFLECTIVE STRIPS AND E-MARKING * TRAILER LIGHT SYSTEMS * ROTATABLE REAR FLOODLIGHTS RAMP * FIXED HYDRAULIC LOADING RAMPS * HYDRAULICALLY ADJUSTABLE LEFT/RIGHT * SUPPORT JACKS: 24 TONNES DYNAMIC, 50 TONNES STATIC OMS * MANUAL RAMP SUPPORTS * POWER CONNECTION FOR HYD...

Condition: used, maximum load weight: 38,440 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 08/2023, next inspection (TÜV): 08/2026, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment list. Full specifications available upon request. - Loading area with rear taper approx. 1,000 mm x 8° - One pair of galvanized one-piece steel ramps, approx. 3,000 x 800 mm - JOST landing legs (mechanical) with 2-speed gearbox rated for approx. 24 t lifting capacity (approx. 50 t test load) - BPW axles and suspension, 1 axle self-steering - Technical axle load: 12,000 kg each - Air suspension with raise/lower valve - Topcoat in solid RAL 3002 carmine red - 2-inch king pin - One galvanized steel front wall, approx. 400 mm high - Electro-hydraulic unit mounted at the rear under the loading area - Load gauge for determining axle loads, including load chart - On the gooseneck: removable ALU side walls and rear wall, approx. 2,440 x 400 mm (L x H) - One galvanized toolbox, integrated in the tapered gooseneck - 6 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the loading area - Galvanized extensions, extendable by approx. 230 mm per side - Lift axle on the 1st axle Hfodpfjxthz Tsx Ab Usr - 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear - 2 LED reversing lights mounted on the rear plate - HRM metallisation (High Resistance Metallisation)

Condition: new, empty load weight: 12 kg, maximum load weight: 54,000 kg, overall weight: 66,000 kg, axle configuration: 3 axles, loading space length: 13,150 mm, loading space width: 2,950 mm, loading space height: 950 mm, suspension: air, tire size: 245/70R17.5, color: red, Year of construction: 2012, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 3 axles, air suspension, 1st axle can be lifted, lifting + lowering, ABS (anti-lock braking system), can be extended to 3.50 m, lashing eyes, 2-part loading ramps, hydraulic ramps, twin tires approx. 8500mm loading length over axles, loading length over pins approx. 4650mm, 2-part hydraulic loading ramps 2500mm + 1500mm, can be extended to 3.5 m, rear axle load (kg) 48000 (3x 16,000kg), 18,000kg fifth wheel pressure for 3-semi-trailer tractor, ONLY FOR EXPORT, ONLY FOR EXPORT ACCESSORIES INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale and errors! Hodpfxei Rnh Tj Ab Usfr - .

Condition: new, suspension: other, color: other, gearing type: other, driver cabin: other, emission class: none, Leveling bracket for low-loader semi-trailer including container closures, price per leveling bracket, , --  Subject to printing errors, mistakes and changes, sample images --, More information at: !, More details: ! Hfodpfx Ajxpwh Ijb Usr

Condition: new, overall weight: 36,000 kg, axle configuration: 3 axles, suspension: air, tire size: 385/65 R22,5, KRONE SD refrigerated trailer | Carrier 1550 deep-freeze unit | KRONE axles with disc brakes | Toolbox | Spare wheel holder | Temperature recorder | Pallet box | Lifting axle | Double-deck. Subject to errors and prior sale. Hfedpfxjxghkhj Ab Ujr

Condition: used, maximum load weight: 24,630 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 04/2017, next inspection (TÜV): 03/2026, loading space length: 12,640 mm, loading space width: 2,540 mm, total width: 2,550 mm, total height: 2,800 mm, Equipment: ABS, Low-bed: 8,740 mm, loading height of bed: approx. 1,060 mm, gooseneck: 3,900 mm, height difference between gooseneck and bed: 580 mm, storage box on gooseneck, continuous underfloor box / stainless steel toolbox, hardwood floor, 27 lashing rings per side, 9 stake pockets per side, stake storage under the chassis, mounting rail for loading ramps at the rear, hydraulic support legs at the front, separate hydraulic unit, Duo-Matic brake connection, hydraulic quick-coupler with 2 connectors, provision for rotating beacon at the rear, ABS, EBS, BPW Eco axle(s), 2nd and 3rd axles with hydraulic forced steering, drum brake system, air suspension with lift/lowering device. The vehicle may feature advertising stickers and/or lettering. Our offer is generally without new MOT (TÜV) approval. Should you require new TÜV approval, we are happy to provide a quote from one of our partner workshops. The vehicle may feature advertising stickers and/or lettering. Our general terms and conditions of delivery and payment apply. Hodoxit Nbspfx Ab Usfr We are happy to provide a financing or leasing offer for this item. Please contact us!

Condition: used, maximum load weight: 175,620 kg, overall weight: 219,000 kg, axle configuration: > 3 axles, first registration: 01/2002, Equipment: ABS, STHP 8 (3+5) 8-piece hydraulic swing BPW axle unit with remote control. Technically permissible total weight: 219,000 kg Payload: 175,620 kg Hydraulically suspended and 8-axle steerable Goldhofer low bed trailer, type STHP (3+5), comprising 4 heavy-duty modules with a detachable gooseneck, up to 5 m long telescopic excavator low bed with 4 wheel recesses, ABS, and technical payload up to 175,620 kg. Consisting of the following four separate heavy-duty modules: 1st Module: Hydraulic universal gooseneck, type STH - Can be combined with heavy-duty dolly modules and overdrive loading bridges - Unladen weight: 5,900 kg - Permissible front fifth wheel load: 35,000 kg - Length: approx. 4.10 m - Saddle height: approx. 1.30 m - King pin: 3.5" - Plug-in aluminum side walls - Fully hydraulically movable 2nd Module: Goldhofer THP/ST3 3-axle heavy-duty chassis module - Permissible total weight (as a single module): 108,000 kg Hfedpfxjxx Evfs Ab Usr - Permissible axle load: 36,000 kg at 5 km/h - Unladen weight: 10,350 kg - Technical payload (as a single module): up to 97,650 kg at 5 km/h - 8 hydraulic pendulum axles, tires: 215/75/R17.5 - Axle load: 25 t at 20 km/h - Vehicle width: 3 m - Axle spacing: 1.5 m - Max. steering angle: ±60° - Hydro-mechanical 2-circuit forced all-wheel steering integrated in chassis, max. axle steering angle: 60°, with integrated hydraulic oil tank - Front/rear optimized pin-plate coupling for longitudinal configurations - Single-wheel pendulum axle assemblies, total 8 wheels per axle line - Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure accumulator suspension - Hydraulic steering for all axles - BPW axles with drum brake incl. ABS, technical axle load 34 t at 5 km/h 3rd Module: Low bed heavy-duty module, extendable - excavator bridge - Year of manufacture: 2002 - Internal dimensions: approx. 7.50 m length, 3.00 m width, loading height 0.40 m - Construction height: 350 mm - Extendable by approx. 5.00 m - Unladen weight: 11,900 kg - 4 wheel recesses, extension module in the front area - Overall height in wheel recess area: approx. 150 mm - Loadable up to 80 t in the low bed and 175.6 t in the complete module combination STHP 8 (3+5) - Front and rear hydraulic bolt plate coupling with claw coupling adapter 4th Module: Goldhofer THP/ET5 5-axle heavy-duty chassis module - First registration: 04.01.2002 - Permissible total weight: 115,000 kg - Permissible axle load: 23,000 kg at 5 km/h - Unladen weight: approx. 14,200 kg - Technical payload: up to 100,800 kg - Single-wheel hydraulic pendulum axles with 4 wheels per axle line, 20 x 285/70 R 19.5 tires - Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure accumulator suspension - Hydraulic steering for all axles - Radio remote control for steering axles 5. Notes: The 4 heavy-duty modules allow for up to 3 different train combinations! Payloads vary depending on combination. The low bed can be inspected and demonstrated at our site. A current manufacturer's certificate from Goldhofer is available for this special low bed combination. Price NET plus 19% VAT. All information subject to change and prior sale. Internal vehicle number: 2285 Advert also available in full German / Inserat auch komplett in Deutsch verfügbar

Condition: new, maximum load weight: 37,635 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpt from equipment features. Complete specifications available on request. Gooseneck: * Gooseneck with front corners beveled approx. 45° and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick One-piece steel ramps: * One pair of galvanized one-piece steel ramps, approx. 3,000 x 800 mm, with approx. 48 mm thick hardwood covering * Ramps with hydraulic lifting mechanism, hydraulically adjustable * Maximum load per pair: 40,000 kg In accordance with Regulation 1230/2012/EU, ramps shorter than 300 mm in driving position do not count towards the vehicle length Loading area: * 1 pair of fixed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) * Wheel recesses with square climbing strips approx. 15 x 15 mm as well as extensions in the lower area * Between the first and second axles, one pair of fixed wheel recesses, approx. 1,610 x 700 x 400 mm (L x W x D). Includes three-piece removable galvanized covers over the wheel recesses (W approx. 670 mm) – max. point load 5 t/each * Recess in the inclined area as well as projecting into the loading area to accommodate excavator boom (approx. 2,900 x 750 x 210/290 mm (L x W x H)) * 1 pair of lashing rings (horizontal) at the front of the loading area (LC 10,000 daN) * 5 pairs of fold-out lashing rings (LC 5,000 daN) * 3 pairs of fold-out lashing rings (LC 10,000 daN), 2 pairs of lashing rings in the excavator boom recess (LC 5,000 daN) * Cut-outs in the outer frame of the loading area to hook in tensioning straps (LC 2,000 daN) Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox, lifting capacity approx. 24 t (test load approx. 50 t) Hfjdjxtc Ubopfx Ab Usr Axles: * BPW axles and suspension, 2 rigid axles, 1 trailing steering axle * Technical axle load: 12,000 kg each * Electromagnetic reversing lock, activated via reverse gear and manually * Air suspension with lift/lowering valve * Axle tool kit Tyres: * Tyres 235/75 R 17.5 3PMSF – brand at our discretion * TPMS: Tyre Pressure Monitoring System in accordance with ECE R 141. Data is transmitted to the tractor via standardized EBS interface according to ISO 11992. For correct display, the tractor unit must be able to receive and display this data Braking system: * WABCO brake system in accordance with EU regulations, with EBS-E (2S2M) and without connection lines to the tractor unit Steel construction: * Steel structure made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Electrical system: * Electrical system in accordance with EU regulations, 24-volt ASPÖCK-NORDIK (ASS3) lighting * ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets * Connections according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Complete steel construction automatically shot-blasted with turbine blasting machine after welding * Second blasting treatment with corundum for optimum coating adhesion * Final coating with 2 layers of 2K topcoat, single color in RAL 3002 Carmine Red as per RAL system 841GL * Rims in silver * Rear section metallized and painted in RAL 9010 (Pure White) * Paint system tested in salt spray mist test according to ISO 9227-NSS * Cavity sealing with special wax Including the following extras: * 2-inch kingpin * One

Condition: used, maximum load weight: 44,750 kg, overall weight: 83,000 kg, axle configuration: > 3 axles, first registration: 07/2013, next inspection (TÜV): 12/2027, Year of construction: 2013, Internal vehicle no.: G300087 German vehicle Immediately available at our yard in Kaufungen - Kassel, Germany More INFO from: * Luis Lucena (German, English, Spanish, French) * Viktoria Sologubova (Polish, Russian, Ukrainian, English) Heavy Duty Tractor Unit Unladen weight: 13,050 kg Gross vehicle weight: 41,000 kg Fifth wheel load: 37,500 kg 630 HP Hedpfxsvzdzis Ab Uefr Euro 6 Leaf / air suspension Retarder Auxiliary heating Low loader Faymonville STBZ-6VA Year of manufacture: 2013 4 axles + 2 additional axles Extendable: 3.2 m Length: 16.43 - 19.63 m Width: 2,750 mm to 3,250 mm Max. gross weight: 85,500 kg Unladen weight: 25,200 kg Vehicle combination Payload: 44,750 kg Unladen weight: 38,250 kg Gross weight: 83,000 kg Length: 20,400 - 23,600 mm Financing example: * Internal number: G300087 * Purchase price: €175,000.00 * Down payment: 10% * Term: 60 months * Monthly installment: €2,740.92 * Final value: €35,000.00 If you are interested in this offer or would like to tailor it to your requirements, please contact us (Mr. Enchev). We look forward to your call. Errors excepted. We are happy to take your used vehicle in part exchange. Financing available directly from us. GOLEC NUTZFAHRZEUGE GMBH We speak: German, English, Spanish, Polish, Ukrainian, Russian, Bulgarian. ----

Condition: used, empty load weight: 23,620 kg, maximum load weight: 73,580 kg, first registration: 05/2009, next inspection (TÜV): 01/2024, total length: 14 mm, total width: 25,500 mm, total height: 9,000 mm, suspension: steel-air, tire size: 245/70 R 17.5 /10mm, wheelbase: 1,300 mm, mileage: 242,697 km, front tire size: 245/70 R 17.5 /10mm, operation weight: 97,200 kg,

Condition: used, empty load weight: 8,434 kg, overall weight: 39,000 kg, axle configuration: 3 axles, first registration: 04/2022, suspension: air, tire size: 385/65 R22.5, Equipment: ABS, | Schmitz refrigerated semi-trailer SCB S3B | TK SLXi 300 refrigeration unit | Pallet box | Internal width: 2.45 m | Internal height: 2.64 m | Schmitz axles with disc brakes | Spare wheel holder, toolbox | Diesel hours: 4,925 h | Subject to errors, input mistakes, and prior sale Hodpfx Absxv Etfs Uefr

Condition: new, suspension: other, color: other, gearing type: other, driver cabin: other, emission class: none, fuel: biodiesel, Storage compartment for aluminum ramps, price per storage compartment, length approx. 2.48 m, width approx. 1 m, height approx. 27 cm, , --  Misprints, errors and changes reserved, sample images --, More information at: !, More details: ! Hodpfoxnx Rnjx Ab Uefr

Condition: used, maximum load weight: 51,870 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, first registration: 03/2025, next inspection (TÜV): 03/2026, total width: 2,540 mm, Equipment: ABS, You can find our entire vehicle inventory, including immediately and short-term available vehicles, on our website. Hsdpextc Uhofx Ab Usfr Excerpt from the equipment list. Complete equipment details available upon request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, length approx. 3,700 mm, rear with chamfer approx. 1,000 mm x 10° * For tractors: 4 x 2, 6 x 2, and 6 x 4 * Plug-in steel front wall, approx. 400 mm high * At the front connection strip: yellow-red air couplings * ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic power unit for hydraulic operations * External beams of the gooseneck with mounting holes for bolted lashing rings * One mounting hole at the rear upper part of the gooseneck external beam for a bolted lashing ring * 1 pair of screw-in lashing rings included (LC 10,000 daN) * On the gooseneck, 1 pair of plug-in side aluminum drop sides, approx. 400 mm high, anodized version * On the gooseneck, 1 plug-in aluminum rear wall, approx. 400 mm high, anodized version * Approx. 40 mm thick hardwood flooring above the gooseneck * 2-inch kingpin * Gooseneck guide plate for fifth wheel, approx. 500 mm wide * Rear gooseneck mounting for aluminum ramps * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Loading platform, extendable version, length approx. 8,800 mm, rear with chamfer approx. 500 mm x 10° * Recess in the platform and chamfer for accommodating the excavator dipper stick approx. 2,490 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension * 1st and 2nd axle fixed, 3rd and 4th axles steering trailing axles * 3rd and 4th axles with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with raise and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Complete platform and interrupted between the axles with approx. 50 mm thick hardwood flooring (increasing the coefficient of friction) * Platform locking with conically welded locking profiles every approx. 250 mm * Elongated slots for insertable and repositionable bridging elements at the front of the platform * Intermediate table with set-down platform, approx. 300 mm wide, for large cross-section telescopic tube with sheet metal covering – front and rear with elongated slots for insertable and repositionable bridging elements – removable cover flush with the platform * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 6 pairs of flush-mounted lashing rings in the outside frame of the platform, foldable outward (LC 10,000 daN) * Additionally, 1 pair of lashing rings externally on the front cross member of the platform, approx. 90° turned inward towards the platform (LC 10,000 daN) * Extendable galvanized widening extensions by approx. 230 mm per side * 1 pair of permanently installed wheel recesses, open up to the extension, approx. 700 x 410 mm (W x D), sheet-covered in the platform ahead of the 1st axle, wheel recesses with square climbing strips approx. 15 x 15 mm, spaced approx. 200 mm * Between the 2nd and 3rd axles, 1 pair of permanently installed wheel recesses on the platform, approx. 1,695 x 700 x 410 mm (L x W x D), covers for wheel recesses split lengthwise, with wooden overlay, outer plug-in loc

Condition: used, empty load weight: 9,711 kg, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 04/2016, suspension: air, tire size: 385/65 R22,5, Equipment: ABS, | Schmitz SBC S3B refrigerated trailer | Meat conveyors | Thermo King SLX300 refrigeration unit | 12,499h on diesel | Pallet box | Schmitz axles with disc brakes | Spare wheel holder, toolbox | Interior height: 2.65m | Subject to errors and advance sale Hjdpfxew Dd Tce Ab Ujfr