Part Handling

DMG Mori WH 10

Condition: excellent (used), Year of construction: 2012, operating hours: 10,168 h, functionality: fully functional, machine/vehicle number: NL254120635, CNC turning machine Manufacturer: DMG MORI Type: NLX 2500 SY 700 with WH10 automation Year of manufacture: 2012 Turning diameter: 460 mm Turning length: 795 mm Control system: MORI SEIKI M730 BM Diameter over cross slide: 590/360 mm Spindle bore: 80 mm Travel distances X/Z: 260/795 mm Total power consumption: 40 kVA Machine weight: approx. 6.4 t Space requirement: approx. 3.994 x 3.056 x 2.187 m Kedjy Szwhspfx Ag Uedt

Condition: excellent (used), Year of construction: 2018, total length: 9,800 mm, total width: 4,000 mm, feed length X-axis: 3,500 mm, feed length Y-axis: 1,100 mm, feed length Z-axis: 1,100 mm, feed rate X-axis: 30,000 m/min, feed rate Z-axis: 5,000 m/min, table length: 3,000 mm, table load: 6,000 kg, table width: 1,200 mm, power: 22 kW (29.91 HP), Surface grinder Ziersch - Z1030 MACH-ID 9597 Make: Ziersch Kdedpfx Asy En Dneg Uet Type: Z1030 Control: Mitsubishi Touch Year: 2018 X - Travel: 3500mm Y - Travel: 1100mm Z - Travel: 1100mm Table Length: 3000mm Table Width: 1200mm Table load: 6000 Feed rate X-Axis: 30000mm/min. Feed rate Z-Axis: 5000mm/min. Grinding stone dimensions:500 x 100 x 203mm Power: 22kW Speeds: 3000Rpm Cooling system: yes Feed rate Y-Axis: 3000mm/min. Length: 9800mm Width: 4000mm Height: 4500mm Weight: 27500kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 2007, condition: ready for operation (used), Cutting range round: 560mm, cutting range flat (W x H): 620/560mm, material feed length, single: 900mm, multiple feed: 9999mm, shortest cut length: 6mm, minimum diameter to be cut: 15mm, minimum remnant in single cut: 15mm, shortest remnant length in automatic mode: 80mm, saw motor power, frequency-controlled: 5.5kW, cutting speed, stepless: 13-127m/min, saw blade dimensions: 7400/54/1.6mm, material support height: 700mm, total drive capacity in basic configuration: 12kW, length: 2370mm, width: 3610mm, overall dimensions with chip conveyor (L/W): 2370/3610mm, machine table height lowered: 2230mm, weight: approx. 5.2t with chip conveyor. An inspection on site is possible. Kdedpfx Agoxg Rhvs Uot

Condition: used, Year of construction: 2003, CNC machining center, universal Manufacturer: AXA Type: VPC 40 U Year of manufacture: 2003 CNC control: Heidenhain TNC 430 Kedpjwwt Nmefx Ag Ujdt Travel distances: X/Y/Z = 2,300 x 1,200 x 600 mm NC rotary table dimensions: 1,100 x 1,100 mm Fixed table dimensions: 1,100 x 1,100 mm Tool holder: SK40 Tool magazine: 60 positions Spindle speed: 10,000 rpm Weight: approx. 20 tons 9926ä

Condition: new, thread dia. M3 - M8 mm Kedpfefg U Snjx Ag Usdt

Condition: new, Year of construction: 2025, A compact design sheet fiber laser metal cutting machine with complete protection Small occupied space balances complete protection and higher safety. Each frame of the cutting machine bed is welded after mortise-and-tenon joint to achieve perfect mechanical property and better stability and firmness. The pull-out cutting machine table, with the electric table optional, saves space occupation and freshen up the user operation experience. Convenient and fast open&close with one click; The laser cutter door is safe and reliable, by using rack-pinion transmission mode combined with self-locking cutting machine system Fiber laser heads are able to detect jutting obstacles to effectively reduce the damage rate and save the maintenance cost of a laser cutter. Applicable Material: metal Condition: New Laser Type: Fiber Laser Laser Power: 1500W, 2000W, 3000W, 6000W, 12000W Cutting Area: 1000*1500mm Cutting Speed: 0-100m/min Kdedpfxehwrgas Ag Ujt Positioning accuracy: ±0.05mm Repositioning accuracy: ±0.03mm Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING

Condition: new, ⭐⭐⭐⭐⭐ (5.0) 42 ratings ✈️shipping : 45-day delivery ✈️ ✅✅✅Energy class A+++✅✅✅ ⚡️ Top service ⚡️ Fast delivery ⚡️ Great support! ⭐€10,850 EXCL.VAT & SHIPPING⭐ ►►Buy It Now◄◄ ✳️Keep your liquidity! We offer a variety of financing models to ensure your investment has the best chance of success. Contact us today to learn more about our hire-purchase, warranty or lease programs. ✳️ ➖➖➖➖➖ ►►►⌛⏰ FASTEST delivery time❗ ⌛⏰►►► ✨✨Buy directly from the manufacturer and secure the price and quality advantage!✨✨ Benefit from Proton's 40 years of experience in surface coating technologies. ➖➖➖➖➖ ☘️Eco-Friendly☘️⚡️Green Energy⚡️☘️ ⭐ Paint Booth – WETLINE-SP-1500 ✔️ Internal dimensions: 1390 mm L * 1500 mm W * 1400 mm H ✔️Pool height : 561 [mm] ✔️Filter system : double layer water curtain ✔️Filtering material : city water, plate filter and mechanical separator with backwash ✔️Filter material cleaning : thin and thick grid ✔️ Pump output : 1.5 [kw/h] 940 [d/d] x 1 piece ✔️Number of fans : 1 piece ✔️Fan performance : 5,400 m3/h x 1 ✔️Fan motor power : 3 kw/h ⭐The cabins can be made of galvanized sheet metal or stainless steel. They can be designed to be integrated into the automatic and manual systems. ⭐At the pool there is a platform for material and personal safety. The platform covers the entire pool. Ksdjc Uthdepfx Ag Usdt ⭐In the Filterline wet painting booth, environmental pollution is prevented by the simultaneous use of 3 different filter systems. ⭐Wet paint particles, sucked in the air by a suction fan, are caught by the water curtain at the back of the cabin and transported into the pool. ⭐Wet paint particles in the trace amount that are not caught by the water curtain are caught by the separators on the suction ducts on the back of the water curtain, and the fresh air outlet is from the flue. ⭐The backwash system is applied in the separator section to help the process of retaining the wet paint particles of the separators. The filtration efficiency, whose contact area is increased by spraying wash water through the nozzles, is maximized. ⭐While paint dirty water accumulated in the basin enters the pump suction chamber, it goes through a coarse and a fine mesh to prevent clogging of the pump spray water, thus ensuring paint particles are retained. ⭐When the dirty water in the pool becomes unusable, it can be disposed of from the waste water valve located behind the grates in the suction department. ⭐By using a paint separator system, the water in the pool is cleaned from the paint and used continuously. ⭐The separated paint residues are drained by a filter press and must be disposed of properly. ⭐Price quoted is for the smallest standard size in stainless steel. All devices/machines are new, not used. Do you want a special configuration ❗ Call us now❗ ☀️ 2 YEAR WARRANTY ☀️ ☀️We have CE certificates for all our machines and ATEX certificates for the necessary machines.☀️

Condition: used, TECHNICAL DETAILS - Number of axes : 3 MILLING SPINDLE - Tool holder type : BT30 - Spindle power : 20 [kW] - Spindle speeds : 24000 [rpm] - Number of spindle hours : 4877 [h] LINEAR AXES - Travels on X/Y/Z axes : 700/420/380 [mm] - Rapid traverses rates (X/Y/Z) : 60 [m/min] TOOL CHANGER - Auto. Tool Changer type : Parapluie - Tool magazine capacity : 25 - Tool exchange time : 0.9 [sec] TABLE - Table dimensions : 840/420 [mm] - Maximum weight upon table : 400 [kg] - Distance table / spindle nose (min./max.) : 200-580 [mm] POWER SUPPLY - Supply voltage : 400 [V] - Total installed power : 16 [kW] WEIGHT & DIMENSIONS - Machine floor space : 1650/2950 [mm] - Machine height : 2550 [mm] - Machine weight : 3400 [kg] MACHINE HOURS - Number of hours under power : 14493 [h] - Number of working hours : 5307 [h] EQUIPMENT - CNC : Siemens 840D SL - Interface : Ethernet / RS232 / USB / PCMCIA - Rigid tapping - 3 colors status lamp - Coolant tank * with high-pressure pump : 15 [bars] - Coolant through spindle Kdjdoxcqadspfx Ag Ujt - Chips conveyor - Tool probe : Renishaw OTS - Workpiece probe : Renishaw OMP40-2 - Electric transformer

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, travel distance X-axis: 635 mm, travel distance Y-axis: 510 mm, travel distance Z-axis: 460 mm, number of slots in tool magazine: 20, controller manufacturer: Heidenhain, overall weight: 3,600 kg, table length: 760 mm, table width: 560 mm, controller model: ITNC 530, feed rate X-axis: 30 m/min, feed rate Y-axis: 30 m/min, feed rate Z-axis: 30 m/min, rapid traverse Z-axis: 30 m/min, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 30 m/min, rotational speed (max.): 8,000 rpm, rotational speed (min.): 20 rpm, spindle speed (max.): 8,000 rpm, spindle speed (min.): 8,000 rpm, table load: 600 kg, Equipment: documentation/manual, rotational speed infinitely variable, Deckel Maho DMC 635 - Control: Heidenhain ITNC 530 - Travel range X-, Y-, Z-axis: 635 / 510 / 460 mm - Feed rate: 0.01–10,000 mm/min - Rapid traverse: 30 m/min - Spindle speed: 20–8,000 rpm - Table clamping area: 790 x 560 mm - Tool holder: SK40 DIN 69871 - Tool magazine with 20 stations - Machine weight: approx. 3,600 kg - Rinsing gun - Coolant/air blast selection (M25) - Handheld control unit Ksdpfx Agex Hfngs Usdt The machine is in very good condition, with only a few spindle operating hours. Inspection and testing under power at our premises is of course possible. We are pleased to offer you transport, installation, and commissioning at your site as well. Everything from one source: We, Baumgärtner CNC GmbH & Co. KG, are a company specializing in: - Service - Maintenance - Overhauls - Automation of DMG machines and other well-known manufacturers. We support you! From machine purchase, through transport and installation, to commissioning and subsequent maintenance or repairs, you can rely on us.

Condition: used, Year of construction: 2015, x-travel 1140 mm y-travel 710 mm z-travel 610 mm CNC-control Heidenhain TNC640 table-size 1300 x 700 mm max. table load 1000 kg Kdodpfxoxx A Ewj Ag Ujt spindle taper SK 40 spindle turning speed range 8.000 U/min feed stepless max. 10.000 mm/min rapid traverse 24/24/24 m/min tool change unit 30 Pos. coolant IKZ 40 bar drive capacity - spindle motor 7,5 / 11 kW voltage 400 V total power requirement 25 kVA weight of the machine ca. 9,0 t dimensions of the machine ca. 3,25 x 3,08 x 3,00 m chip conveyor 4,30 x 0,80 x 1,60 m band filter unit 2,00 x 1,00 x 1,30 m coolant tank 1,30 x 1,00 x 0,60 m - Serial No.: 4P11152J1 - Machine ON: 23,320 h - Spindle ON: 5,042 h - Control: HEIDENHAIN TNC 640 - TSC 40 bar incl. 600 liter coolant tank with paper band filter unit - Y-Axis with 4 liear guide rails! - Chip conveyor - X- and Z-Axis with 6 roller supports for each axis!