Low loader semitrailer

FAYMONVILLE MAX Trailer MAX100 Semi-Tieflader

Condition: new, maximum load weight: 40,320 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Below is an excerpt of the features. Complete equipment list available upon request. GOOSENECK Gooseneck with a rear slope of approximately 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood decking approximately 30 mm thick. - 2-inch kingpin - Yellow-red air couplings on the galvanized connection bar at the front. - 4 wheel chocks with holder on the front wall (± 5 kg). LOADING AREA 5 pairs of lashing rings that fold outwards (LC 5,000 daN). 3 pairs of lashing rings that fold outwards (LC 10,000 daN). 1 pair of lashing rings lying at the front in the loading area (LC 10,000 daN). Hardwood decking approximately 48 mm thick, with diamond plate decking over the axles. - On the gooseneck and at the rear, left and right, one holder each for the warning signs, including a socket. - A galvanized steel front wall. - 3 height-adjustable wooden planks. - Galvanized folding supports under the slope of the loading area. - A holder for a rotating beacon at the rear of the semi-trailer. - Height-adjustable tarpaulin superstructure, approximately 3,960 mm. - Galvanized front wall with a tensioning mechanism for the sliding curtains. - Height-adjustable by approximately 400 mm. - Roof from the EDSCHA brand, which can be moved forward on aluminum roof rail profiles. - 3 pairs of sliding rails in the loading area. - The superstructure can be hydraulically widened at the rear to the left and right by approximately 750 mm (for loading and unloading). - Sliding cover with a pivoting portal beam. - Sliding tarpaulin with approximately 700 mm of reserve in length, with tension straps at intervals of approximately 600 mm. - Height of the top edge of the superstructure approximately 3,960 mm (loaded). - Driving with the sliding cover open is not permitted and will damage the tarpaulin. - Attachment rail for aluminum ramps at the rear of the vehicle. - Control valves for the hydraulic widening of the superstructure, mounted on the right side of the semi-trailer. (± 4 kg) - White reflector tape according to EU regulations, red on the sides and rear. - Electro-hydraulic unit at the rear under the loading area. (± 45 kg) - Holder for a pair of warning signs on the front wall. - Four warning signs, approximately 400 mm extendable, approximately 423 x 423 mm, with an LED position light (± 25 kg). Gkedpfx Alsz N Nx Rs Soc - On the warning signs, a holder for a rotating beacon. - 7 pairs of rail pockets for plug-in rails, approximately 100 x 50 mm, in the outer frame of the loading area (± 21 kg) - Lift axle on the front axle, controlled by TEBS-E depending on the current axle load and loading condition (± 69 kg). - 6 pairs of recessed lashing rings along the central beam (LC 5,000 daN). - 1 pair of recessed lashing rings along the central beam at the rear (LC 10,000 daN). (± 27 kg) - A painted layer of sand on the diamond plate on the gooseneck and in the loading area as anti-slip protection. - 1 LED reversing light, each on the left and right, in front of the first axle. - 2 LED work lights mounted on the rear panel. - An acoustic warning signal when reversing. ACCESSORIES - Cable for supplying the electro-hydraulic unit and/or the electric winch (approximately 35 mm², approximately 3.5 m long, max. 250A) between the semi-trailer and the tractor unit with a plug connection (NATO-NATO). FIFTH WHEEL BRACKETS JOST fifth wheel brackets, mechanical, with a 2-spee

Condition: used, maximum load weight: 37,150 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 04/2026, next inspection (TÜV): 04/2027, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Excerpt from the equipment list. Complete equipment available upon request. Gooseneck * with angled front corners approximately 45° and rear slope approximately 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approximately 30 mm thick, extendable loading platform Loading platform * extendable design with rear slope approximately 1,000 mm x 8° * 6 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 3 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings lying horizontally at the front of the loading platform (LC 10,000 daN) * Recesses in the outer frame of the loading platform for attaching lashing straps (LC 2,000 daN) * Hardwood flooring, approximately 48 mm thick, diamond plate flooring over the axles Kingpin supports * JOST kingpin supports (mechanical) with 2-speed gearbox for approximately 24 t lifting capacity (approximately 50 t test load) Tires * 235/75 R 17.5 3PMSF * TPMS: TPMS tire pressure monitoring system according to ECE R 141 * Data transmission to the tractor unit takes place via the standardized EBS interface according to ISO 11992. * For correct display, the tractor unit must be able to transmit and display this data. Axles * BPW axles and suspension, 2 fixed axles, 1 steerable axle * Technical axle load: 12,000 kg each * Electro-magnetic parking brake activated via reverse gear and manually Air suspension * with lifting and lowering valve Braking system * in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Steel construction * made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Painting * Complete steel construction automatically blasted with a shot blasting system after welding * Second blasting with corundum for optimal adhesion of the coating system * Final painting with 2 layers of 2K topcoat * solid color in RAL 3002 carmine red * in accordance with the RAL system 841GL * Rims in silver gray * Rear section metallic and in RAL 9010 (pure white) * Paint structure tested in the salt spray test according to ISO 9227-NSS * Sealing of cavities with special wax Electrical system * in accordance with EU regulations * Lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the connection bar at the front with 24N, 24S & 15-pole sockets in accordance with ISO. 24N ISO-1185 24S ISO-3731 15-pole ISO-12098 Included accessories * Axle tool * 2-inch kingpin * One galvanized steel front wall, approximately 400 mm high * One spare wheel holder in front of the front wall * Yellow-red air couplings on the galvanized connection bar at the front * Mounting in the rear area of the gooseneck for aluminum loading ramps * Galvanized folding supports under the slope of the loading platform * One mounting for warning signs on the gooseneck and on the rear panel, left and right * including socket loadometer for determining the axle loads including load diagram * Aluminum side walls and rear wall on the gooseneck, pluggable, approximately 2,440 x 400 mm (L x H) Gsdoz N Nwyjpfx Al Sjkc * The rear galvanized locking strips are removable. (Length of the superstructure approx. 2,560 mm) * A toolbox galvanized, integrated in the angled gooseneck * 3 pairs of WADER container pockets in the loading platform for a 20' (30') or a 40' cont

Condition: used, maximum load weight: 37,885 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 08/2024, next inspection (TÜV): 08/2026, Equipment: ABS, Excerpt from Equipment List Loading Platform * in extendable design with a rear slope of approximately 1,000 mm x 8° Gedpfx Aljzv A Aqj Sokc Hardwood Decking * approximately 48 mm thick, with ribbed metal sheeting over the axles JOST King Pin * (mechanical) with 2-speed gearbox for an approximate lifting capacity of 24 tons (approximate test load of 50 tons) BPW Axles and Suspension * 2 fixed axles * 1 trailing axle * Technical axle load: 12,000 kg each Air Suspension * with lifting and lowering valve Braking System * in accordance with EU regulations with EBS-E (2S2M) Accessories * 2-inch king pin * One galvanized steel front panel, approximately 400 mm high * Load manometer for determining axle loads, including load diagram * Aluminum side and rear walls on the gooseneck, pluggable, approximately 2,440 x 400 mm (L x H) * One galvanized toolbox integrated into the sloping gooseneck (± 47 kg) * 3 pairs of WADER container pockets in the loading platform for a 20' (30') or 40' container. (± 30 kg) * 6 pairs of stake pockets for pluggable stakes, approximately 100 x 50 mm, in the outer frame of the loading platform. (± 18 kg) * Galvanized extensions, extendable by approximately 230 mm on each side (± 230 kg) * Lift axle on the front axle * Adjustable mounting rails for aluminum ramps at the rear of the vehicle * 2 LED reversing lights mounted on the rear panel * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear (± 16 kg) * Four warning panels, extendable by approximately 400 mm, approximately 423 x 423 mm, with an LED position light. (± 25 kg) * A mounting bracket for a rotating beacon on the warning panels * One rotating beacon supplied separately * HRM Metallization (High Resistance Metallization) Painting * Top coat, single color in RAL 3002 carmine red.

Condition: used, maximum load weight: 34,030 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 07/2025, next inspection (TÜV): 07/2027, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and in the short term, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck: Gooseneck with rear slope, approximately 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood flooring, approximately 30 mm thick. Loading platform: Loading platform can be hydraulically raised and lowered after the gooseneck, length approximately 2,800 mm, with rear slope approximately 1,000 mm x 8°. 6 pairs of lashing rings that can be folded outwards (LC 5,000 daN). 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN). 1 pair of lashing rings that can be folded inwards on the center beam at the front (LC 10,000 daN). Grid floor C40/4 (point load approximately 2.3 t on an area of approximately 20 x 20 cm) above the axles. Diamond-plate floor. Two-piece steel ramps: One pair of galvanized two-piece steel ramps in reinforced design, approximately 3,185 + 1,420 x 1,250 mm, with grid floor C40/5 (point load approximately 8 t on an area of approximately 20 x 20 cm). Ramp with hydraulically raising and folding ramp sections and hydraulic lifting mechanism, maximum load per pair: 40,000 kg. In accordance with Regulation 1230/2012/EU, ramps with a length of less than 300 mm do not need to be taken into account in the vehicle length of 16,500 mm when in the driving position. Gedpfx Ajzu Ebtjl Sokc Landing gear: JOST landing gear (mechanical) with 2-speed gearbox for approximately 24 t lifting capacity (approximately 50 t test load). Tires: 235/75 R 17.5 3PMSF TPMS tire pressure monitoring system according to ECE R 141 Axles: BPW axles and suspension. 2 axles rigid, 1 axle steered. Technical axle load: 12,000 kg each. Electro-magnetic parking brake via reverse gear and can also be activated manually. Air suspension with raising and lowering valve. Braking system: WABCO braking system according to EU regulations with EBS-E (2S2M). Colors: Semitrailer RAL 3002 carmine red. Rims silver. Tarpaulin in RAL 9006 silver. Including accessories: 1 spare wheel holder under the loading platform on the right in the direction of travel. 2-inch King Pin. One galvanized steel front panel. Yellow-red air couplings on the galvanized connection strip at the front. 4 wheel chocks with holder on the front panel. 3 height-adjustable wooden planks. Galvanized folding supports under the slope of the loading platform. Height-adjustable tarpaulin superstructure *3,960 mm*. Galvanized front panel with a tensioning mechanism for the sliding curtains. Roof from EDSCHA, height-adjustable by approximately 400 mm, can be moved forward on aluminum roof rail profiles (screwed to the front and rear walls). 3 pairs of adjustable load securing bars in the loading platform. The superstructure can be widened by approximately 750 mm on the left and right at the rear by hydraulic means. Sliding tarpaulin with approximately 700 mm reserve in length, with lashing straps at intervals of approximately 600 mm. Top edge of the superstructure approximately 3,960 mm (loaded). Driving with an open sliding tarpaulin is not permitted and will result in damage to the tarpaulin. On the diamond plates on the gooseneck and on the loading platform, a sand layer is applied as an anti-slip coating. Cover plates to bridge the gap between the ramps and the loading platform. Electro-hydraulic unit at the rear under the loading platform. On the gooseneck and on the ramps, one holde

Condition: new, maximum load weight: 47,300 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, loading space length: 8,600 mm, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately and at short notice, on our website. Excerpt from the equipment list. Full specifications available on request. Gooseneck: * Gooseneck with beveled front corners (approx. 45°) and rear bevel (approx. 750 mm x 10°) * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Extendable loading platform with rear bevel (approx. 1,000 mm x 8°) * 5 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) * Cutouts in the outer frame of the loading area for hooking tensioning straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick; over the axles, diamond plate surface Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox, 24t lifting capacity (50t test load) Tyres: * 235/75 R 17.5 3PMSF tyres, brand at our discretion Axles: * BPW axles, two rigid axles, two trailing steering axles, air-suspended, with drum brakes, lifting/lowering function * Steering axles with electromagnetically-activated reverse lock (via reverse gear or manually) * Axle tools Brake system: * WABCO brake system in accordance with EU regulations with EBS-E (4S3M), no connecting lines to the tractor unit Steel structure: * Steel construction from high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield 355 MPa) S690QL/S700MC (yield 690 MPa) Electrical system: * Electrical system compliant with EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets (ISO standard: 24N - ISO 1185, 24S - ISO 3731, 15-pin - ISO 12098) Paintwork: * Premium and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc-rich primer * High-quality 2-component (2K) single-color topcoat RAL 3002 Carmine Red * Rear section metallized and painted in RAL 9010 (Pure White) * Rims in silver Accessories: * Spare wheel holder in front of the bulkhead (without spare wheel) * 2 inch kingpin Gksdpfx Aljyvnfgj Ssc * Galvanized steel front wall approx. 400 mm high * Yellow-red air couplings on the galvanized front connection bar * Receptacle at the rear of the gooseneck for ALU loading ramps * Galvanized drop-down supports under the loading area bevel * Bracket for a revolving beacon at the rear of the trailer * Brackets left and right on the gooseneck and rear plate for warning signs including socket * TPMS tire pressure monitoring system compliant with ECE R 141 * Removable ALU sideboards and rear wall on the gooseneck, approx. 2,440 x 400 mm (L x H); rear galvanized insert posts are removable (body length approx. 2,560 mm) * Galvanized toolbox integrated in the beveled gooseneck * 3 pairs of WADER container locks in the loading platform for one 20' (30') or one 40' container * Sliding hook-in rails for ALU loading ramps at the rear of the vehicle * 6 pairs of pockets for plug-in posts, approx. 100 x 50 mm in the outer frame of the loading area * Galvanized extensions, extendable by approx. 230 mm per side * Lift axle on the front axle with TEBS E control based on current axle load and load status * 2 LED reversing lights mounted on the rear plate * 2 pairs of ferry-

Condition: new, maximum load weight: 36,020 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our full vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Complete equipment details available on request. Gooseneck: * Gooseneck with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Loading area with rear bevel approx. 1,000 mm x 8° * 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) * 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) * 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate above the axles Two-piece steel ramps: * One pair of galvanized two-piece steel ramps, approx. 3,185 + 1,420 x 1,250 mm, with grating covering C40/5 (point load approx. 2.8 t on a surface of approx. 20 x 20 cm) * Ramp with hydraulically foldable ramp sections and hydraulic lifting system * Maximum load per pair: 30,000 kg Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 steering trailing axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock activated via reverse gear and manually * Air suspension with raise/lower valve Tyres: * Tyres 235/75 R 17.5 3PMSF – brand at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Brake system: * WABCO brake system compliant with EU regulations, with EBS-E (2S2M), without connection lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system according to EU regulations, LED lighting 24V ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * HRM metallisation of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to guarantee optimum corrosion protection * Finishing coat: 2 layers 2K topcoat, solid colour RAL 3002 carmine red as per RAL system 841GL * Rear section metallised and painted RAL 9010 (pure white) * Rims in silver Included accessories: * One bracket for warning signs on the gooseneck and at the rear left and right, including socket * 1 spare wheel holder under the loading area, right in the direction of travel * 2" kingpin * One galvanized steel front wall * Yellow-red air couplings on the galvanized front connection bar * 4 wheel chocks with brackets on the bulkhead * 3 height wooden boards * Galvanized folding supports under the loading area bevel * Bracket for rotating beacon at rear of trailer * Height-adjustable tarpaulin structure – approx. 3,960 mm * Galvanized front wall with tensioning system for sliding curtains, height adjustable by approx. 400 mm * EDSCHA roof, sliding forward on aluminum roof girder profiles (screwed to front and rear wall) * 3 pairs of sliding stakes in the loading area * The body is hydraulically extendable to the left and right at the rear by approx. 750 mm * Sliding roof with pivoting portal crossbeam * Sliding curtain with approx. 700 mm reserve length, ratchet straps at approx. 600 mm intervals. Height O Gedpfx Aey Auhusl Sokc