FOLDING MACHINE

Fidia Combi

Year of construction: 2018, condition: new, Freeze dryer completly new. Pilot plant. Capacity:1 kg / 8hrs Effective Area :0.15 m2 Wet Input per 8 hr: 1 Kg Dry Output per 8 hr: 0,2 Kg Temp Range Drying: 30 ºC - 100 ºC Water Removal Capacity: 0,8 Kg Ultimate Condenser Temp: -40 ºC Defrosting Method: Natural Total Connected Load : 1Ph/15 Amp Connection Average Connected Load: 1Ph/15 Amp Connection Bodpfx Ajfn Iudeaaslf Plant dimensions: 1,1m*0,7m*1,5m 1. Freeze Drying Capacity: Wet input 1 kg. per shift. On a higher side, each shift shall be of 8 to 8.5 Hrs. The wet input can either be biological cultures, enzymes, polymers, extracts, sprouts, vegetables, fruits, nutraceuticals, herbs, spices, sea foods, instant curries/gravies etc. of minimum 15% solids. 2. Residual moisture: Final moisture content on the product shall be less than 4%. 3. Compressed air: Maximum pressure 5Kg/Sq.cm. Flow rate 3 cubic Meter/Hr. Material: Stainless steel 304 Flow rate vacuum pump: 13 m3/h

Condition: new, capacity 90 degrees: round 305 mm capacity 90 degrees: square 260 mm 350x200 saw band length 3375x27x0,9 mm band speed 37 + 74 m/min table height 940 mm total power requirement 1,5/1,8 kW weight of the machine ca. 0,65 t dimensions of the machine ca. 1,5 x 1,75 x 1,9 m SPECIAL PRICE!!! Double miter metal band saw, hydraulic semi-automatic GBS 305 HA-I Easy - Miter cuts up to 60° left and 45° right - Material height button Blodpfed Iipxox Aaaof - Ball bearing turntable - hydraulic Vice, laterally displaceable - Massive, large material support - Automatic cooling

Condition: used, Hohner universal stitching head 52/8 - 6er ring eyelet - for round wire No. 24 - 26 - with various accessories acc. pictures condition as shown in the photo Bsdpfofc Rx Tox Aaaelf

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, Paint/spray booth Bsdpjia Taujfx Aaaolf dimensions without fan and control Panel! Extraction surface - dimensions (mm): 3000(w)x1900(h) Overall dimension(mm): 3100(w)x2350(h)x1910(d) Technical data: - Fan power 3kW (ATEX) - Fan suction capacity: 16000 m³/h (max 1100Pa) - Lighting: 2 pcs 2x36W (ATEX) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us.

Condition: used, Year of construction: 1993, Technical details: mould plates - length / width: 500 x 400 mm Heating: Zweistufen Heizung 4,6 und 6,0 kW control: SPS voltage: 380 V (3x 20A) / 24 DC V work height adjustable: 870 - 970 mm total power requirement: 6 + 2,5 kW dimension machine xH: 2,8 x 1,1 x 1,3 m weight: 570 kg Compact angle welding machine with shrink tunnel PACKAGING MACHINE WITH SHRINK TUNNEL AND COOLING STATION AND SPECIAL COOLING FAN movable/mobile Application areas/products: -div. brochures, plans or other made of paper/cardboard in DIN A 5 / DIN A 6 Applicable films: all half tube shrink films up to 0,060mm Welding system = impulse welding, with teflonized separation seam, adjustable automatic transport of goods into the shrink tunnel further details: -Tunnel passage width: 450mm -Tunnel passage height adjustable to 100, 200, 300 and 400mm -length of the heatable tunnel hood 900mm -Prod. output of the machine depends on product and film 5 to 20 cycles / minute (manufacturer's data) -max. film width (folded half tube) 550 / 550mm at 25 - 50 my -frame dimension 500 x 500 x 290 mm = max. Verpackungsmaß Heating: -two stage heating 4,6 and 6,0 kW -Fan infinitely variable Cooling station: -outlet 300mm -with blower Conveyor belt: -feed rate 2.5 - 12 m/min -steplessly adjustable Bledpfxju Nu Hij Aaaef i.d. *

Condition: new, Year of construction: 2025, functionality: fully functional, total length: 5,000 mm, total width: 3,500 mm, total height: 2,950 mm, inner dimension height: 2,650 mm, inner dimension length: 4,900 mm, inner dimension width: 3,400 mm, Equipment: cabin, Automotive Spray Booth The automotive spray booth is a fundamental device in paint repair technology. It enables painting operations to be carried out in safe and comfortable conditions while minimizing the negative impact on the surrounding environment and the workspace. Specifications: - External dimensions: 5000 (+ air handling unit 1350 × 2900 mm) × 3500 × 2950 mm - Entrance door: 3000 × 2600 mm (three-wing design) - Service door: 700 × 2000 mm - Structure: made of steel sheets - Heat exchanger: standard steel - Panels: steel panels with mineral wool insulation in the walls Cabin Wall Structure: - Thickness: 50 mm - Insulation: EPS polystyrene - Color: white Cabin Base: - Cabin mounted directly on floor/concrete surface Double Ceiling: - External ceiling paneling - Full-surface plenum chamber for air supply Air Exchange System: - Supply system: - Jet turbine 4 kW – 2 units - Airflow capacity: 26,000 m³/h Bljdpsxnpczsfx Aaaef - Airflow system: - Jet turbine 5.5 kW – 1 unit - Airflow capacity: 18,000 m³/h Lighting: - 8 side-mounted lamps - Ceiling lighting: 24 LED tubes Air Heating System: - Single-stage oil burner Riello model 40 G20 - Burner control: manual - Heating time: 8–15 minutes Filtration System: - Double-layer filtration structure - High-capacity air purification system with filtration efficiency up to 99%

Condition: new, Year of construction: 2025, total height: 4,000 mm, total length: 7,000 mm, total width: 3,000 mm, warranty duration: 24 months, temperature: 80 °C, air demand: 36,000 m³/h, input voltage: 380 V, heating capacity: 345 kW (469.07 HP), power: 40 kW (54.38 HP), fuel: liquid petroleum gas (LPG), energy consumption: 40 kWh, insulation material: Mineralwolle, insulation thickness: 50 mm, nominal power: 345 kW (469.07 HP), Equipment: lighting, MAIN STANDARD Our paint booths are designed to meet all necessary requirements for paint application, including air filtration, extraction, lighting, and a controlled environment. Booth processes are managed via a PLC system, ensuring that desired values are maintained consistently. Bsdpfx Aaowzmcboajlf OPERATING PRINCIPLES OF THE BOOTH The booth’s processes are managed through a control panel, which oversees the following steps: PAINTING PROCESS During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled through the extraction unit. Floor filters (paint stop filters) collect paint particles, and the air passes through final exhaust filters before being discharged. FLASH-OFF PROCESS After painting, the booth continues operating for approximately 15 minutes to purge residual solvents and thinners. During this phase, fresh air circulates from outside into the booth. DRYING PROCESS In this stage, 80% of the air passing through the booth is heated to 60°C and introduced via a distribution system. Since 20% of the solvent is released during drying, it is expelled with the exhaust air. Industrial coatings are typically dried at 60°C, but the booth temperature can be adjusted as needed via the control panel. COOLING PROCESS After the 30-minute drying cycle, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the subsequent 5-minute cooling phase, fresh air from outside circulates through the booth, after which the system shuts down automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT These control panels govern the functions and operation of machines and devices housed within the booth. The panel is made of durable galvanized sheet and steel profiles and is fully enclosed to protect against dust and moisture. Electrical Equipment and Control Panel: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control connections between the control panel and motors or other electrical devices. • Electrical wiring is designed to accommodate booth relocation if needed. • Operating equipment uses 380 V 50 Hz, while control devices operate at 220 V. • The booth’s operation time can be monitored on the electronic control panel, enabling straightforward maintenance scheduling. • Temperature and time settings for booth ventilation (solvent flash-off), intermediate drying, and final drying can be easily adjusted to required values on the digital display of the electronic control panel. • Users can monitor and adjust the drying time using the heating thermostat and time relay.

Condition: used, Year of construction: 2007, General Information • Machine type: Modular flexographic printing and converting press • Maximum printing width: 510 mm Printing Units Number of printing units: 3 Drive system: Dual drive per printing unit Printing technology: Flexographic Plate cylinder pitch: 1/8" Plate Cylinders (1/8") • 3 × Z88 • 3 × Z92 • 3 × Z96 • 3 × Z100 • 3 × Z108 • 3 × Z116 • 3 × Z120 • 3 × Z140 Die-Cutting Units Number of die-cutting stations: 3 Counter-pressure cylinders: 2 stations equipped with adjustable counter-pressure cylinders (Spilker Variabase) Magnetic Cylinders (1/8") • 2 × Z96 • 3 × Z100 • 3 × Z108 • 3 × Z116 • 3 × Z120 • 4 × Z140 • 3 × Z176 • 3 × Z184 • 2 × Z192 • 1 × Z222 Anilox Rollers Total anilox rollers: 13 Volumes (cm³/m²): 4.1 / 5.04 / 6 / 6 / 6.3 / 6.09 / 8 / 8.25 / 9.58 / 13 / 13.51 / 16.57 / 30 • 2 new anilox rollers included Coating & Special Units • Sleeve holders for varnishing: - 3 × sleeve holders Z88 - Including mounting station • Screen printing unit • Laminating station Drying Systems UV systems: 3 × UV units Uviterno, 240 W/cm NIR drying: 2 × NIR modules for water-based systems (Lambda Technology) Web Handling & Rewinding Grid winders: 2 × rail-mounted grid winders (up/down) Rewinder: Double-spindle rewinder for roll-to-roll operation Delivery: Conveyor belt for single labels Web cleaning system Complete set of non-stick rollers Corona & Web Guiding Corona treater: 2 kW (SIT) Web guiding system: Bljdpfxsx Ngfls Aaajf • Erhardt+Leimer (E+L) • 2 × ultrasonic sensors • 1 × line sensor Inspection & Register Control Video inspection system: E+L Elscan Register control: • Sensotec • Register control for 5 stations (3 printing + 2 die-cutting) Inserter control for pre-printed rolls

Condition: excellent (used), P/N: 190.101 // Fabrik No.: 616 Further MACHINERY / SPARE PARTS & MACHINE COMPONENTS of this type are available in our warehouse. ON REQUEST Bodpfognlb Ajx Aaaolf

Condition: good (used), Year of construction: 2007, Gallus EM 510 • Year of manufacture: 2007 • Maximum printing width: 510 mm • Printing units: 3 dual-driven print stations • Application: Self-adhesive label production _____ Printing Equipment • 3 flexographic printing units with dual-drive technology • Plate cylinders (1/8"): 3 × 88, 3 × 92, 3 × 96, 3 × 100, 3 × 108, 3 × 116, 3 × 120, 3 × 140 • Magnetic cylinders (1/8"): 2 × 96, 3 × 100, 3 × 108, 3 × 116, 3 × 120, 4 × 140, 3 × 176, 3 × 184, 2 × 192, 1 × 222 • 13 anilox rollers (various volumes: 4.1; 5.04; 6; 6; 6.3; 6.09; 8; 8.25; 9.58; 13; 13.51; 16.57; 30) • 2 brand new anilox rollers • 3 sleeve systems z=88 for varnishing (including mounting station) • Screen printing unit _____ Die-Cutting & Converting • 3 die-cutting stations • 2 stations equipped with adjustable counter-pressure cylinders (Spilker Variabase) • Laminating station • Waste matrix removal on rail system: o 2 matrix rewinders (upper/lower) • Double-spindle rewinder (roll-to-roll) • Insetter system for pre-printed webs • Register control for 5 stations (3 printing + 2 die-cutting, Sensotec) _____ Drying & Treatment • 3 × Uviterno UV curing systems (240 W/cm) • 2 × Lambda Technology NIR drying modules for water-based inks • Corona treatment 2 kW (SIT) _____ Web Guiding & Control • E+L web guiding system with: o 2 ultrasonic sensors o 1 line sensor • E+L ELSCAN video inspection system • Web cleaning system • Complete set of anti-adhesive rollers Blsdox Hacrspfx Aaaef _____