Rotary table

KAMA KURA

Condition: excellent (used),

Condition: used, Year of construction: 2005, x-travel 600 mm y-travel 500 mm z-travel 600 mm control iTNC 530 Heidenhain Pgedpfxjvxwq Ej Aknjr table surface area 900 x 500 mm spindle turning speed - stepless 0-12.000 U/min spindle drive 10 kW tool taper SK40 DIN 69871 tool magazin: 24 total power requirement 22 kW weight of the machine ca. 6,4 t dimensions of the machine ca. 5,3 x 3,5 x 3,5 m Chip conveyor scraper belt Coolant system 3 pumps / cartridge filter Grundfoss high-pressure pump type CRK2-220/22 A-W-A-AUUV

Condition: new, Year of construction: 2026, Miter saw and cut-off saw, type: ZS 200 N - 5 KW motor with machine stand, but without saw blade Machine operated via handwheel and worm gear (rear) Tilting Saw blade diameter: 520 mm, saw blade arbor bore: 50 mm Saw blade speed: 2800 rpm 400 volts / 5 KW (S6/40%) motor with brake and automatic star-delta motor switching Cutting width at 90 degrees: 420 mm Cutting width at 45 degrees: when tilted: 295 mm Cutting height at 90 degrees: 200 mm Cutting height at 45 degrees when tilted: 140 mm The saw can be tilted to an acute angle of approximately 25 degrees on one side and tilted flat to the left up to 30 degrees. Machine weight: approx. 250 kg Location: Available from stock in 54634 Bitburg - immediately available - Pjdei Dfidopfx Aknsgr

Condition: used, machine/vehicle number: 1 284 066, Feed diameter: 200 mm Through-hole: 50 mm Mounting, short taper according to DIN 55027: Size 6 Outer diameter of the clamping cylinder: 290 mm Overall height (clamping cylinder to the front of the chuck, without jaws): 150 mm Podecm Tgkepfx Aknsgr pneumatically actuated

Condition: used, Year of manufacture: 1980s/90s Technical data: Centre height: 185 mm Centre distance: 750 mm Turning diameter over bed: 370 mm Spindle bore: 36 mm Bed width: 250 mm Speed range: 38 - 1600 rpm Tailstock taper: MT 3 Quill stroke: 110 mm Dimensions (W x D x H), approx.: 1950 x 900 x 1200 mm Weight, approx.: 800 kg Equipment: Psdpeydk Hhefx Aknsgr - 3-jaw chuck, make: Röhm, ø 200 mm - Quick-change tool post with 4 holders - Bed stop - Chip tray

Condition: used, Year of construction: 1993, Technical details: tube diameter: 80 mm tube diameter min.: 6 mm control for program: Gelma MM-1 tube pipe draw up length: 1800 mm weight of the machine ca.: 0,232 t dimension machine xH: 1,9 x 0,7 x 1,3 m Pgsdpfsu Ibyyjx Akner Semi-automatic PIPE BENDING MACHINE Operating modes are manual but also semi-automatic Application: for multiple bending of pipes The swivel unit with bending preselection for 3 different bending angles in single and automatic mode. The machine is currently equipped with a stop bar for tube size Ø 10mm for 6 angle settings. The bending machine is movable/adjustable. Equipment/accessories: 6 cam rods/stop rods 6 control disks Bending tool for Ø 12mm *

Condition: new, thread dia. M3 - M8 mm Pgsdpfxofg U Sne Aknjr

Condition: good (used), NHH lathe Type: 1N611N Turning diameter bed: 260 mm Turning diameter support: 160 mm Spindle bore: 26 mm Podsqgdkiopfx Aknegr Turning lenght: 600 mm Digital measurement Diameter faceplate: 155 mm Speed: 2000 RPM Dimensions: 150x85x155 cm LxWxH

Condition: used, Single-column – Eccentric press WEINGARTEN Type EV 63 Machine No. 738 / 61 Year of manufacture 1962 Pressing force 63 tons Stroke 260 mm Table area 630 x 530 mm Table opening Ø 210 mm Slide area 315 x 260 mm Adjustable slide stroke 8-100 mm Slide adjustment 63 mm Tool holder bore Ø 40 mm, with clamping piece Installation height max 450 mm Stroke rate 115 strokes / min Compressed air requirement min. 4.5 bar Motor power 4 kW Power connection 380 Volt, 50 Hz Table height above floor approx. 750 to 900 mm - Electrical stroke release via foot switch or two-hand control - Overload protection by shear plate - Clutch-brake combination by WEINGARTEN friction-thread clutch with top dead center through-drive protection - Front crankshaft support bearing - Press table adjustable in height via 2 threaded spindles - Manual centralized lubrication - Control cabinet positioned beside the press - UVV (German trade association for accident prevention) for manual feeding operations Space requirement L x W x H 1750 x 1600 x 2430 mm Weight 4.5 tons Pjdpok S Htxefx Aknegr Good condition

Condition: new, - incl. sideward drain - incl. pneumatic noise isolating cover - total volume of bowl 53 l - working volume of bowl 40 l - dimension approx. 790 x 415 x 670 mm (h) - dim. of working trough approx. 590 x 290 x 290 mm (h) Pedpfod I Dpiex Aknegr - motor 0,55 kW - engine (rpm) 1500 - bottom P.U. layer of the trough 10 mm - side wall P.U. layer of the trough 8 mm - weight 80 kg - incl. dosing pump - incl. controlbox (speed control included, 1000 – 1500 rpm)