Mobile Line 500

Kreuzmayr KML 500

Condition: used, mileage: 226,206 km, power: 235 kW (319.51 HP), first registration: 10/1981, fuel type: diesel, number of seats: 27, gearing type: automatic, color: white, brakes: retarder, Equipment: air conditioning, bathroom, onboard kitchen, parking heater, This SG 221 HDS was originally intended for shuttle service to Southern Europe, but remained a one-off; nevertheless, it served as the foundation for two further high-deckers of a special kind: the S 215 HDS and S 216 HDS, which would soon bring Kässbohrer many new customers. Additionally, this coach introduced the 'S' designation: it stands for Super, because these new high-deckers truly lived up to their name. With a height of 3.63 meters, the elevated passenger compartment created even more space, accommodating not only more luggage (16 cubic meters) but also additional service facilities. Extra fuel tanks could also be installed without issue. Regardless of which of the two Super-Setras the bus operator chose, the engineering marvel of these two new Ulm models was that, except for the front section, they were 100% modular components from the Series 200 and shared identical bolted assemblies with other Setra touring coaches. The 216 HDS offered space for up to 16 rows of seats. In comparison, the underfloor cockpit variant provided more interior space. With the Setra SG 221 HDS, Kässbohrer had a vision, but due to the ban on running articulated touring coaches through France, they shifted focus in favor of solo vehicles. The SG 221 HDS was subsequently used as a demonstration and information bus at trade fairs and conferences; with its generously equipped kitchen on board, it became a central meeting point for representatives and customers. +++ Unique Vehicle +++ +++ATTENTION!!!!!+++ +++pure restoration project+++ +++not roadworthy / only the engine runs+++ Engine: Mercedes-Benz Mileage according to odometer Transmission: 5-speed automatic Seating: 24+2+1 sleeping seats ---- Safety Retarder * Fog lights Passenger compartment Stand heating * Air conditioning * Tables * Curtains * Jet ventilation * Reading lamps * Double glazing * Footrests * Tap system with bar and large kitchen in rear area * Separate bar area in the center * Lounge area at the front convertible to sleeping area * Refrigerator + additional * Microwave * Rear WC * Driver microphone Exterior Power steering * Tachograph with disc Fpjdpfx Aaormlp Eo Ejd * Sleeping cabin * Driver door * Roof hatches/fans/roof ventilator Other German vehicle documents * Vehicle dimensions: length 18.00m, width 2.50m, height 3.95m * Twin tires * Tires: Front axle approx. 40% Our internal vehicle number: 7271 Subject to errors. Pictures and text may differ from the actual vehicle. Over 180 vehicles always in stock.

Condition: new, Washing machine WA LC40 with centrifugal mill RM40 for single belt press EBP420, EBP500, EBP580 capacity up to 2 000 kg/h power: elevator 2,2 kW mill 4,0 (5,5) kW (PS) electric outlet 400V 50Hz (3 phases) fuse 16 A dimensions: Fjdpfxeb Ncmfs Aa Ejpd length 2,000 mm width 700 mm height 2,200 mm insertion resp. discharge height 800 mm weight 280 kg material 1.4301 / AISI 304 connections: connection for cleaning ½ “ inside connection for waste water 2 “ outside mash discharge height 1,250 mm suitable for pomaceous fruit scope of delivery 7, 9 and 12 mm cutting screen

Condition: used, Year of construction: 2019, Equipment: compressed air brake, Heatable front and rear windshield Additional device holder / Fpsdpfx Aajr Ilxvo Ejd

Year of construction: 2025, condition: new, Nominal capacity 3000kg/h (depending on fruits & operating condition, up to 6000kg/h) Yield up to 75% Fjdpfx Aaeygmwo Espd Belt width/length: 1000mm/approx. 7000mm Working width/high: 900mm/0-50mm continuously Belt speed continuously variable 1,0-5,2m/min Electrical supply: Drive motor 2,2 kW 400V Washing motor: 0,25 kW 400V Waterconsumption for belt cleaning: Approx. 3 l/operating minute Weight approx. 2300kg Dimensions: (lxwxh) 2750x1890x1690mm without high-pressure cleaner and without compressor

Condition: used, Year of construction: 2023, operating hours: 248 h, maximum speed: 50 km/h, front tire size: 600/70 R30 | 0%, rear tire size: 710/70 R42 | 0%, tire size: 710/70 R42, number of beds: 43, Tyres (front): 600/70 R30, Tyres (rear): 710/70 R42, Operating hours: 248, First registration: 17.12.2024 _____ Standard equipment/technical data ENGINE Max. power 180/245 kW/HP (ISO 14396) Max. torque 1100 Nm Maximum power with power boost 194/265 kW/HP Max. torque with power boost 1178 Nm 6-cylinder, 7.4l AGCO Power - 74 LFNT-5D, CR, 4V Emission standard (DOC+SC+SCR) without EGR, Stage V Electronic engine management with Vistronic fan control Engine speed memory Powercore engine air filter with pre-cleaner EasyCare cooling package Additional fuel pre-filter with water separator 500-litre fuel tank Fedpfx Asvv Dp Nja Espd

Condition: new, Year of construction: 2025, power: 45 kW (61.18 HP), ♻ The MONSTER is a hybrid machine with two shaft PRE-SHREDDER P150 TWIN (with two reduction gearboxes) combined with one shaft SHREDDER SD90XL for efficient shredding of various types of pallets. ♻ A shredding system integrated with a conveyor and magnetic separator offers a comprehensive solution for material processing and purification. ♻ The system consists of a powerful shredder combined with pre-shredder, capable of breaking down various materials, a conveyor which helps to evenly distribute the shredded material, ensuring a steady flow for further processing or disposal and a magnetic separator that efficiently removes ferrous or magnetic particles from the mixture, enhancing material purity and preventing equipment damage. Technical data: Shredder with pre-shredder: Fpsdpfx Aotpwrmoa Esd ✔ Power: 30 kW + 1x 5,5 kW-9,2 kW (shredder + pre-shredder) ✔ Shaft length: 870 mm + 1580 mm (shredder + pre-shredder) ✔ Shaft diameter: 270 mm + 355 mm (shredder + pre-shredder) ✔ Shaft RPM: 80-120 + 5,3-10,3 rpm (shredder + pre-shredder) ✔ Number of cutting knives: 2x19 + 12/12 (shredder + pre-shredder) ✔ Granulation: 10-50 mm ✔ Capacity: up to 60 pallets/h* ✔ Material: Pallets ✔ Filling opening: 2072 x 1070 mm ✔ Weight: 4200 kg Z conveyor: ✔ Frequency converter (adjustment of conveyor speed) ✔ Overband magnetic separator ✔ Length: 6500 mm ✔ Width: 350 mm ✔ Capacity: 0,5 kg/s ✔ Power 0,25 kW ✔ Transport wheels 1 years warranty or 1000 working hours

Condition: new, Year of construction: 2023, functionality: fully functional, input frequency: 50 Hz, Make: Pramac GWB 22 Y CDS Noise protection hood: 64 dB(A) 7m Continuous power: 18.4 kVA / 14.45 kW Voltage: 230 / 400 Volt Frequency: 50 Hz Fjdsq A U Axepfx Aa Espd Phases: 3 Diesel engine: Yanmar 4TNV88 BIPGE Exhaust stage: STAGE V Cooling system: Water Cylinders: 4 in series Displacement: 2190 cm³ Intake: Normal Engine speed: 1500 rpm Engine control: Mechanical Electric start Consumption at 3/4 load: 3.87 liters Consumption at full load: 5.17 l/h Generator: MeccAlte ECP28-M/4 or equivalent Type: Brushless Number of poles: 4 Control: Electronic (AVR control) Manual control panel: Key start Voltmeter, ammeter, operating hours counter, Motor fault display Sockets: 1 x Schuko 220V 2 x CEE 16A -230V 1 x CEE 16A -400V 1 x CEE 32A -400V Dimensions: Length: 1645 mm Width: 870 mm Height: 1072 mm Tank capacity: 51 liters Weight: approx. 560 kg Crane eye Forklift can be driven under

Condition: new, functionality: fully functional, Year of construction: 2025, 1 mobile concrete batching plant ( exhibition machine - new) Producer: Stetter Fedpek S Rcdjfx Aa Eepd Type: M C 1 TZ capacity: 56 cbm/h Mixer: Stetter pan mixer 1,0m3 Storage bins / compartment batcher: 4 aggregate inters per 10 cbm (Total 40 cbm) Silos: Optional 2 pcs (80to or 100 to) Mobile silo foundation: Optional cladding/ housing: optional Silo equipment: 2 complete sets for 2 silos (filter, screws, etc) cement dosing hopper water dosing hopper admixture / chemical dosing device: 20 l + 20 l Control unit: automatic control system MCI 460 Operators stand / control container: include - incl. documentation - CE-certificate OPTIONAL possible: - Transport “free construction site” (only inside EU) - Assembly and Commissioning (only inside EU) PRE FEEDING SYSTEM ON REQUEST AND AS OPTION POSSIBLE Inspection of the selling object and of reference "tublomix" plants by appointment possible! Warranty: 12 month Price and more infos on request offer and all price are net and ex stock, mistakes and/or false representations reserve, subject to prior sale

Condition: used, Year of construction: 2019, Used machine Year of manufacture: 2019 Equipment and Technical Data: - For classic nesting processing with wear plate Fpsdpfswka Upox Aa Eed - Machine frame of welded construction with ground and hardened prism guides for the gantry, unit head, and consoles - Gantry-type traveling column - Helical rack and pinion drive in X and Y axes, ball screw in Z axis for precise positioning - Working dimensions: - Max. support area on nesting table: X = 3100 mm, Y = 1560 mm - Max. traverse paths: X = 4695 mm, Y = 2100 mm, Z = 293 mm - Max. clearance height over DYNESTIC table: Z = 100 mm from table top (without wear plate) - Maximum programmable speed Vector speed: 128 m/min X = 80 m/min, Y = 100 m/min, Z = 25 m/min - DYNESTIC table: - Fixed, continuous processing table with grid layout - Continuous grooves in X and Y directions - Groove spacing: 50 mm - Includes 25 meters of sealing cord for clamping the wear plate - Vacuum fields: Single-circuit vacuum system - Drilling unit 7877: - 19 spindles - Drive power: 1.7 kW - 13 vertical spindles: - Individually selectable - Arranged in U-shape - 5+4 in X direction, 4 in Y direction - 32 mm spacing - Max. drill diameter: 35 mm - Total drill length: 70 mm from screw-on end (depending on panel thickness) - Spindle stroke: 70 mm - Rotational direction: alternating clockwise/counterclockwise - Speed (max): 1000 - 4400 rpm, infinitely variable - Tool holder: M10 thread, 11 mm fit - Without tool, without holder - 6 horizontal spindles: - 2 double drill spindles in X direction - 1 double drill spindle in Y direction - Tool holder: M10 thread, 11 mm fit - Max. total drill length: 63 mm from screw-on end - Without tool, without holder - Milling unit 7842: - Power: 12.0 kW (S6) - Max. speed = 1000 - 24,000 rpm, infinitely variable - Max. power at 12,000 to 24,000 rpm - Air-cooled - With HSK-F 63 tool holder - With right-hand threaded nut (for right-hand rotating tools) - With collet chuck for HSK shank - Ceramic ball bearings (hybrid bearings) - Tool weight max. 6 kg (incl. holder) - Tools: milling and grinding tools max. Ø 160 mm - Safety enclosure according to CE standard - Side and rear safety fence - Vacuum pump: 500 m³/h, dry-running - Personnel safety ensured by light barriers in the front machine area - Hand-held control device for remote operation of the machine with the following functions: - Start/stop of the processing program - Control of processing cycle speed - Reset button - Manual feed/rapid traverse for all axes - EMERGENCY STOP - CAMPUS V7 CAD/CAM software 1x machine license consisting of: - CAMPUS NC-HOPS: - Graphic variant system with WOP and CAD/CAM features for creating part variants using macro technology - CAMPUS MT-Manager - CAMPUS Workcenter - CAMPUS DXF interface - Automatic central lubrication - Automatic lubrication at defined intervals - Additional sealing against dust via pressurization in each guide carriage

Condition: new, Year of construction: 2026, The Mobile Fruit Processing Line is designed to conveniently accommodate all the machines necessary for juice production and a smooth work process. It contains: -Fruit and vegetable washer elevator mill MAXIMILL 3000 -Belt press POWERPRESS 1500 -Transporter for leftover mash -Stainless steel tanks -Diesel pasteurizer -Semi-automatic Bag in Box filler -Juice filters -Sink with a stainless steel table Fpedpeq Nl Afjfx Aa Eod Capacity: 1500 kg/h. Other available capacities: 400 kg/h, 800 kg/h, 1200 kg/h. Features: -The mobile juice line conveniently contains all the machines required for fruit processing & juice production. -Requires only 1 person to operate the whole line. -Mobility is the biggest advantage which eliminates costs for premises and provides the ability to change location. -The juice yield from apples is ~75 % . -All machines are interconnected and controlled automatically. -The mobile juice production unit includes a Bag in Box filler which fills the juice into both Bag in Box and Stand up Pouch packages. -The mobile juice line can be customized on client’s request. -The line is easy to operate and maintain. -The mobile fruit processing line is installed in a specially made trailer which can be easily opened for work and shut when needed. -The biggest advantage of our Mobile Fruit Processing Line is the ability to produce juice anywhere you like. This way the client avoids additional expenses for premises and gets the ability to change work location. Mobility is the key aspect here which provides the client with more possibilities, such as developing a juice pressing service business at various apple farms or different towns.