Used Benford 4000 for sale (3,593)

Year of construction: 2013, condition: used, Technical data of the bale opener line for RDF. MSW, paper, cardboard: Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland Type BO 4000 Year of manufacture 2015 Quantity of opened bales 674 pieces Operating time only 3 days, exclusively by running in the entire line during new installation Opening time approx. 45 seconds per bale Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm Max. Bale weight 2,000 kg Conveying height of the system 1,400 mm Max. Conveying width of the system 1,200 mm Material to be opened RDF/MSW Availability of the line 98% Noise level of the bale opener line 85 dB(A) Total connected load 37 kW Rated current 125 A Operating display SIEMENS SIMATIC HMI Touch Isdpfxeu Tg I De Adiea Control SIEMENS S7 ET200S Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h) Scope of delivery: Feed conveyor 3,500 x 1,200 x 1,400 mm Feed conveyor to opener 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in hydraulic oil tank Heating in control cabinet Oil cooler in Hydraulic unit Explanation of the short period of use: The entire line of Cross Wrap bale openers type BO 4000 was installed at a municipal waste incineration plant in 2015. The background to the installation was that in the case of a malfunction or maintenance of the incinerator, the municipal waste could continue to be received, baled, wrapped and stored until the malfunction was cleared. Then the bales should all be opened again and the waste fed into the normal incineration process. This worst-case scenario never came to pass. The plant was set up, run in and then never used in regular operation. Only during the commissioning and running-in of the entire plant in 2015 were 674 bales opened on three days. The plant is in very good condition and ready for operation immediately. Due to reconstruction measures in the incineration plant, the installation area of the bale opener was needed. As a result, the entire line is for sale. Short description of the wrapping process: The pressed bales are placed on the infeed conveyor belt from the side or from behind by means of a forklift truck. For opening, the bales must run horizontally to the conveyor belt with the wire or twine binding, otherwise the bales must be turned 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or twine strapping. The front and rear rotating knives slit the bale lengthwise. Afterwards, the gripper returns to the starting position. The opened bale is now conveyed via the conveyor belt to the discharge chute and then falls onto the following conveyor system. Comments: New price of the completely plant 296.000,- €. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) is complete. The unit has been dismantled into freight-manageable units, stored and is available for inspection and loading at short notice. We do not accept any liability for the technical details or any errors.

Condition: good (used), Year of construction: 2008, travel distance X-axis: 4,230 mm, travel distance Y-axis: 1,950 mm, travel distance Z-axis: 750 mm, table length: 4,000 mm, table width: 1,250 mm, table load: 11,000 kg, Portal milling machine KAO MING - KMC 4000 SV-H Double guideway two box way construction Head changer for Multi-Face machining off larger compontents ATC tool changer for Horizontal and vertical milling head swivabel Distance table spindle nose    213 - 1093 mm Distance table spindle center  130 -.mm Indexing Horizontal head 5 Degrees x 72 positions HeidenHain iTNC530 with HR410 handwheel Spindle torq 1018 Nm ISO50 Universal Huron type milling head X - Travel: 4230mm Y - Travel: 1950mm Z - Travel: 750mm Distance between column:1500mm Table Length: 4000mm Table Width: 1250mm Table load: 11000 Feed rate X-Axis: 12000mm/min. Feed rate Y-Axis: 15000mm/min. Feed rate Z-Axis: 12000mm/min. Spindle Taper: 50ISO/Bt/Mk Power on spindle: 26kW Speeds / ranges: 4400Rpm ATC / revolver: 30 Chip conveyor: Yes Coolantsystem: Yes Length: 10100mm Iodpfxjxf E Two Adiea Width: 4500mm Height: 4250mm Weight: 30000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 2016, x-travel 560 mm y-travel 560 mm z-travel 660 mm control Celos Siemens 840 sl Operator table surface area 400 x 400 mm rapid traverse 60 m/min table rotating 360 x 0,001 B-Achse ° table load 0,4 t numbers of pallets 2 turning speed range 15000 U/min max. torque on the spindle 207 Nm power capacity - milling spindle 30,7/26/18,5 kW no. of tools in the magazine 60 Stück tool taper SK 40 | weight 9,3 t dimensions 4,2 x 2,7 x 2,8 m Equipment: - full B-axis table - Thru-the-spindel coolant system 70 bar - chipcoveyor - Helical cutting - Synchronized tapping - absolute scale - one extra pallet - band filter system Knoll - oil dust collector - cable less 3D touch probe - tool break detection - elct. hand wheel Iodpsw Eygzsfx Adiea - spindle cooling - Roto Clean

Condition: new, Year of construction: 2025, table length 4000 mm table width 2000 mm table height 200 mm weight 2400 kg Manufacturer: GERD WOLFF Technical Details: • Length 4000 mm • Width 2000 mm • Height 200 mm • Weight 2400 kg • Hole diameter 28 mm • Hole spacing 100 mm • Plate thickness: 25mm Advantages and Features: • 3-day gas nitriding process • Increased corrosion resistance • Weld spatter adhesion protection • Maximum load capacity • Enhanced fatigue strength • Improved vibration resistance • Fine scale engraving • Reinforcement with welded seams and ribs on the underside • Optimal working height of 820-865 mm • 8 height-adjustable support legs • Available with a matching accessory set (optional) Our welding tables are manufactured using HT 300 cast iron and are nitrided as a whole after mechanical processing. Furthermore, they feature precise fine scale engraving using laser technology. To ensure adequate stability, our welding tables are reinforced with welded seams and ribs on the underside (see illustrations). Additionally, they undergo a 3-day gas nitriding process, enhancing their corrosion resistance, fatigue strength, and vibration resistance, among other factors. All our tables come with adjustable legs. The minimum height adjustment range Isdjuia I Nopfx Adisa is 620 mm, while the maximum is 665 mm, allowing for a variable working height of 820 to 865 mm. Additional available dimensions: • 1000 x 1000 x 200 • 2000 x 1000 x 200 • 1200 x 1200 x 200 • 1500 x 1000 x 200 • 1500 x 1500 x 200 • 1500 x 2000 x 200 • 2000 x 3000 x 200 • 3000 x 1500 x 200 • 3000 x 2000 x 200 • 4000 x 2000 x 200 • 2400 x 1200 x 200 Please note that the images are not to scale and are for illustrative purposes only. Our welding tables are produced for our distribution brand "GERD WOLFF Maschinenfabrik" by a reputable manufacturer. 3D Welding Table - 3D Clamping Fixtures - 3D Precision Welding Table

Condition: used, Year of construction: 2019, Technical details: voltage: U1: 400V V open-circuit voltage: 70 V weight of the machine approx.: 100 / Gerät kg dimensions of machine: ca. 0,85 x 0,37 x 1,25 pro Gerät m 4 Fronius TransPuls welding systems available Can be used for industrial applications, e.g. robots. Areas of application: Welding process “CMT”, for all MIG/MAG welding work mobile, 4 wheels / 2x of which swivel with wire feed type: VR 7000-CMT: Wire feed speed 0.5 - 22 m/min; use of possible wire Ø 0.8 - 1.2 mm RCU5000i univoSD remote control 1 meter intermediate hose package Trolley Protection class IP 23 AF cooling type Operation via display RCU 5000i i.D. Ijdpsu Nwhiofx Adiea *

Condition: excellent (used), Year of construction: 1987, functionality: fully functional, For sale: this lathe. Swing diameter over bed: 1,000 mm. Turning length: 4,000 mm. Sinumerik 840D control. Iedpoxzr Rbjfx Adioa

Condition: used, BASIC DATA Condition: Very good Availability: 01/2025 Machine model: DMG NHX 4000 Year of manufacture: 2017 Operating hours: 41,220 h Spindle hours: 21,663 h Working area: X-axis travel: 560 mm Y-axis travel: 560 mm Z-axis travel: 660 mm TRANSPORT WEIGHT AND DIMENSIONS Transport weight Machine incl. tool magazine and chip conveyor: 9,300 kg Coolant unit KF 110/700: 1,500 kg Chiller unit: approx. 82 kg Sheet metal parts: 125 kg Documentation and accessories: 60 kg Transport dimensions of the machine incl. tool magazine: Length x Width x Height: 4.20 m x 3.20 m x 2.80 m SPINDLE INFORMATION Spindle specification Spindle type: SK004 motor spindle speedMASTER® HSK-A63 Spindle speed: 20–20,000 rpm Power: 35 kW (40% duty cycle), 25 kW (100% duty cycle) Torque: 130 Nm (40%), 86 Nm (100%) Workpiece weight per pallet: max. 400 kg Pallet size: 400 x 400 mm Max. workpiece diameter: 630 mm Max. workpiece height: 900 mm TOOL CLAMPING SYSTEM AND TOOL CHANGER Tool holder: HSK-A63 Standard: DIN 69893 Form A Clamping mechanism: Clamping: Mechanically by spring force Unclamping: Hydraulically Tool changer: Capacity: 40 tools (ring magazine system) Max. tool diameter: 70 mm (adjacent pockets free), 170 mm (adjacent pockets occupied) Max. tool length: 450 mm Max. tool weight: 12 kg Optional tool changer: Ring tool magazine with 60 pockets (HSK-A63) POWER SUPPLY Voltage: TN-S system, 400 V Power consumption (at 100% duty cycle): Base machine: 45 kVA Coolant unit: 48 kVA Band filter unit: 55 kVA Mains connection rating for Siemens Sinamics S120 16 kW: 0.48 MVA 36 kW: 1.08 MVA 55 kW: 1.65 MVA 80 kW: 2.40 MVA 120 kW: 3.60 MVA COOLING SYSTEM AND CHIP DISPOSAL Coolant: Water-soluble coolant Iodpjxn Adlefx Adioa Interface for high-pressure coolant system: Up to 70 bar, compatible with Knoll systems Coolant flushing system: Includes cleaning guns Additional components: Rotating inspection window on the work area door Coolant flushing system for cleaning the machine interior Upgraded cooling system: Larger Bürner filter unit (DMG upgrade, see attachment) MEASUREMENT AND MONITORING SYSTEMS Tool breakage control system in tool magazine Spindle sensor measurement system with Renishaw OMP60 for automatic measurement and centering CONTROL SYSTEM CNC: CELOS® with Siemens 840D sl Operate Control panel: 21.5" ERGOline® Control with multi-touch display Functions: Apps for simplified machine operation as well as for comprehensive management, documentation, and visualization of order, process, and machine data. Networking with CAD/CAM and compatibility with PPS/ERP systems. WORKTABLE NC table: With direct drive technology Minimum indexing: 0.001° Max. rotational speed: 100 rpm DOCUMENTATION AND ADDITIONAL FEATURES Electrical schematics and user manuals in German Languages: Screen texts available in German and English CELOS products DMG MORI NETSERVICE for remote diagnosis SERVICE AGENT for maintenance monitoring MESSENGER for real-time machine status

Condition: new, functionality: fully functional, Universal centre lathe ŠKODA SRM 125 - 4000 after modernization of the mechanical part of the machine. The electrical part is equipped with Siemens CNC control: SIEMENS SINUMERIK 828D with SINAMICS drives. Technical data: Maximum swing over bed: 1,250 mm Maximum swing over carriage: 900 mm Maximum distance between centres: 4,000 mm Maximum workpiece weight: 14,000 kg Maximum torque: 34,000 Nm Minimum turning diameter: 200 mm Bed height: 620 mm Bed width: 1,100 mm Spindle nose: No. 10 Number of speed ranges (infinitely variable in each range): 3 Spindle speed range: 1.4 – 350 rpm Main spindle drive motor: 39 kW, fixed gear ratio 1:3 Maximum workpiece diameter in jaws: 1,030 mm Spindle centre taper: 80 mm – 1:10 Centre height above bed: 630 mm Carriage: Feed rate (Z and X axes): 2,000 mm/min Rapid traverse (Z axis): 6,000 mm/min Ijdsxyxdxopfx Adija Rapid traverse (X axis): 3,000 mm/min Traverse motor (Z axis): Siemens 1FK7 101, 27 Nm, with planetary gearbox Traverse motor (X axis): Siemens 1FK7 060, 6 Nm, with planetary gearbox Maximum tool section: 70 × 70 mm Maximum tool section for turret head: 50 × 50 mm Tailstock: Quill stroke: 200 mm Tailstock centre taper: 80 mm, 1:10 Tailstock feed rate: 2,000 mm/min

Condition: used, functionality: fully functional, INDUMAC FOLDING MACHINE Isdpfjxltgxox Adiea 4000 X 100 TON WITH REGISTER USED MACHINE INTERNAL CODE: SVR 290

Condition: excellent (used), Year of construction: 2022, operating hours: 2,330 h, functionality: fully functional, machine/vehicle number: 7535, overall weight: 28,500 kg, power: 405 kW (550.65 HP), Mobile Shredding Plant LINDNER URRACO 4000 DS (self-propelled) Discharge conveyor with overband magnet, dust suppression system, compressed air compressor for machine cleaning SF12.9 shaft pair with accessories Ijdpfoxyq Ipjx Adioa Pre-breaker shaft pair with accessories available upon request

Condition: used, Year of construction: 1997, Technical details: tube diameter: 4,75 - 8,0 mm wall strength: - mm bending radius min.: unterschiedlich, various, variada mm bending angle max.: 180 ° compressed air: min 4,5 bar Total power requirement: ca. 10 kW Weight approx.: 6,0 t Iedpju Ibuksfx Adiea dimension machine xH: 6,3x3,7x2,0 m dimensions electric cabinet: 1,8x0,5x2,7 m dimension control panel: 0,85x0,68x1,65 m fully automatic numeric control for bending of hydraulic supply pipes, car brake pipes various length - various numbers of bending possible (max. 100 bendings per pipe) - 2 independent bending module, every modul has 2 NC axis with functions: " longitudinal process (axis 1 and 3) and " turning of bending head" and bending (axis 2 & 4) - program memory for 250 pipes (lines) - the feeding unit consits of manual a manually filled drum magazine (drum magazine pipe dia.=4,75mm up to dia=8,0mm with 500/1000 pcs) - load swiveling arm - control panel Bundy GHF 60134 accessories: - div. single and add-on parts *

Condition: used, MAKE – TUSCAN MODEL – TL29 YEAR – 2002 CONTROL – FANUC OT TURRET – 8 POSITION WITH LOADS OF HOLDERS SWING OVER BED – 740 mm SWING OVER CROSS SLIDE – 420 mm CENTRE DISTANCE – 4000 mm Iodpfx Aewmlcdjdisa SPINDLE BORE – 250 mm TRAVERSES – X-AXIS 500 mm/Z-AXIS 3700 mm SPEED – 15-700 RPM MOTOR – 3 SPEED GEARBOX MOTOR 30KW SWARF CONVEYOR 4 JAW CHUCK SWARF CONVEYOR

Condition: new, Year of construction: 2025, Ref. -No.: 10461 Manufacturer: IGREK Type: DT 4000 Year of construction: 2025 Type of control: CNC Control: SIEMENS SINUMERIK 840D SL Storage location: Istanbul Country of origin: Türkiye Spindle Speeds: 4000 RPM Turning Height: 2000 mm Table Diameter: 4000 mm Spindle power: 37 kW Max. Table load: 40 t Rotate table rotation speed: 60 RPM Max. Turning diameter: 5000 mm Max. Turning height over faceplate: 2000 mm Iedoxmd Suspfx Adisa Max Spindle Torque: 1200 Nm Spindle Taper: ISO 50 Machine length: 7500 mm Machine width: 12000 mm Machine Height: 9500 mm Weight Of The Machine Ca.: 125 t Further information: Ram Slide Stroke: 2100 mm Ram Section: 350 x 350 mm Vertical Travel of the Moving Traverse: 2000 mm Table Drive System: Segmented Direct Drive Motors Table Torque: 8200 Nm - 14400 Nm max. Table Guide System: Hydrostatic Bearing and Guides IGREK DT 4000 – Your solution for precise heavy-duty machining The IGREK DT 4000 is a state-of-the-art CNC vertical turning center designed specifically for the precise machining of large components. Equipped with a 4,000 mm hydrostatic rotary table and a movable crossbeam, it enables the efficient machining of workpieces with a maximum turning diameter of 5,000 mm and a turning height of up to 2,000 mm. Key features: Hydrostatic rotary table: The 4,000 mm rotary table with hydrostatic bearing ensures maximum precision and smooth running when machining heavy workpieces. Movable crossbeam: The vertically movable crossbeam with a stroke of 2,000 mm offers flexibility and allows adaptation to different workpiece heights. Powerful spindle: With a spindle speed of up to 4,000 rpm and a power of 37 kW, the machine is designed for demanding machining tasks. High load capacity: The rotary table can accommodate workpieces weighing up to 40 tons, enabling the machining of large and heavy components. Multifunctional machining: Thanks to the live spindle and the precise positioning of the C-axis, milling and drilling operations are possible in addition to turning, which increases the versatility of the machine. The IGREK DT 4000 combines advanced technology with high performance and flexibility to meet the requirements of modern manufacturing processes. Its robust construction and wide range of machining options make it the ideal solution for the precise machining of large components in various industries.

Condition: new, Year of construction: 2024, functionality: fully functional, HIGH-PRESSURE PUMP HT SERVO-JET4000 A well thought-out principle with great effect. HIGH-PRESSURE PUMP HT SERVO-JET4000 A well thought-out principle with great effect. + Up to 40 % energy savings compared to conventional systems, Investment eligible for subsidies + High energy efficiency: servo direct drive, no reactive current, low and and flexible power consumption + Low connected load required: no power consumption when the WSS system is at a standstill of the WSS system, suitable for companies with low energy supply + 3-piston plunger pump: high liter capacity and high efficiency of up to 98 %, replaces 6000 bar technology, long maintenance intervals, simple design, no hydraulic system, no warm-up and start-up phase - ready to start immediately + Permanent pressure control and integrated pulsation damping: Continuous readjustment of the cutting pressure to the set value - no pressure fluctuations, higher cutting speed than with a pressure intensifier in a comparable combination Iedpou Hz Tqjfx Adisa + Lowest noise level of 75 dB: high-quality complete unit with soundproof housing + Can be used universally for all waterjet machines and brands

Condition: ready for operation (used), Year of construction: 2006, General Data Measurements width 3755 mm Measurements depth 2300 mm Measurements height 2610 mm Machine weight 9600 kg Main Drive Spindle speed range 14000 rpm Tool taper 7/24 Taper No. 40 Number of axis 4 Movement X-Axis Movement 560 mm X-Axis Rapid Traverse 50000 mm/min Y-Axis Movement 560 mm Y-Axis Rapid Traverse 50000 mm/min Z-Axis Movement 630 mm Z-Axis Rapid Traverse 50000 mm/min Table Outer length 400 mm Outer width 400 mm Table load 400 kg This 4-axis MORI SEIKI NH 4000 DCG was manufactured in 2006 and features a horizontal machining centre with only 1,300 hours on the main spindle, which was overhauled in April 2022. If you are looking to get high-quality milling capabilities, consider the MORI SEIKI NH 4000 DCG machine we have for sale. Contact us for more information. Application Types Milling Isdpfxoxya Dgo Adija

Condition: used, HYDRAULIC BENDING MACHINE MEBUSA MODEL 174-4000 CNC bending length 4100 (4665) Liquidation by auction due to cessation of activity and permanent closure of a used industrial machinery trading company Iedjxzt Sgspfx Adija Brand: MEBUSA Model: 170-4000 Pressing force: 170 T Power: 20 HP Max. bending length: 4050 mm Throat depth: 400 mm Distance between uprights: 3050 mm Distance between tables: 450 mm Speed: 37-7.5-60 mm/sec. Dimensions: 4115x1820x2610 mm Weight: 11,800 kg Distance between tables: 450 mm

Year of construction: 2018, condition: used, Technical details: lifting capacity: 0,125 t swival range : 180 ° Arm length: 4000 mm arm length:: Säule - Kranhaken: 3850 mm height lower edge cantilever arm: 3000 mm column diameter: Ø 220 mm rotation: 270 ° Dimensions of the crane assembled: LxWxH: 4800 x 1300 x 3250 mm Dimensions of filling container: LxWxH: 1100 x 1000 x 740 mm Column height: 3200 mm Ijdeu Utmpepfx Adioa Heavy-duty operation = manual with swivel stop Hoist: Hans Hebetechnik load capacity 1000kg; lifting height approx. 2400mm; hook Ø 30mm with rope safety device; travel distance hoist 2700mm; control via pendant control The crane can be moved via the filling container. *

Condition: used, Year of construction: 2006, x-travel 600 mm y-travel 400 mm z-travel 400 mm control MSX 501 Mori Seiki table surface area 700 x 450 mm Iodpfx Adsv Az Uceioa max. table load 350 kg number of T-slots 4 T-slot - width 18 mm T-slot - distance 100 mm Number of revolutions 12.000 U/min power capacity - main spindel 18,5 / 15 / 11 kW tool taper BT 40 max. Torque 110,5 Nm diameter of forward milling spindle bearing 70 rapid travel x/y/z 20.000 mm/min feed speeds 1 - 20.000 mm/min Tipp feed 15 Steps / 0 - 1.260 mm/min Number of Toolpositions in magazine 40 Pos. Max. mould width 80 mm max. tool-dia with free toolbox 125 mm max. tool length 250 mm max. tool weight 8 kg change-time chip to chip 2,8 sec change-time tool to tool 1,0 sec total power requirement 34 kVA weight of the machine ca. 7,2 t dimensions of the machine ca. 2,8 x 3,0 x 2,9 m Machining Center Vertical MORI SEIKI - NV 4000 DCG - ca. 14.000 Operating-Hours

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, We are selling this machine as we no longer have any use for it. Price is VHB we need the space. English version below: Ijdpfxjtgxyqs Adiea We sell this machine because we don't use it anymore and we need the space. The price is open to discuss.

Condition: good (used), Year of construction: 1997, Flanging and dishing machine BOLDRINI - RIBO 20 HY x 4000 Hydraulic Press and Manipulator Field off aplication Pressure vessel Division Tank Head Manufacturing Iodpfx Adexcnpcsiea Silos & Storage tanks Road & Railway Tankers Fume heads Boiler manufacturing   Knuckel heads R-30 / 40 / 50/ 60 / 70 / 80 / 90 / 100 Turning attachment eletric driven Attachment for smaller diameter Motorized Clamping cyinder in X-Direction on nose Extended closed nose construction Stainless telescopic covers in X-way Max. workpiece: 4000Ø Maximum sheet thickness: 20mm Max. dishing radius: 400mm Min. product Ø: 30 Max height on dishing side:900mm Working speed: 0 - 5000mm/min. Power: 45kW Length: 8000mm Width: 1800mm Height: 2900mm Weight: 13000kg

Condition: excellent (used), functionality: fully functional, Year of construction: 2019, operating hours: 4,963 h, load capacity: 5,000 kg, lifting height: 4,000 mm, load center: 600 mm, fuel type: gas, mast type: duplex, construction height: 2,950 mm, motor manufacturer: G.M., gearing type: hydrostat, fork carriage width: 1,350 mm, fork length: 1,200 mm, fork width: 150 mm, fork thickness: 50 mm, tire condition: 100 %, front tire type: superelastic tires (black), front tire size: 23X10-12, rear tire type: superelastic tires (black), rear tire size: 355X45-15, overall weight: 12,500 kg, empty load weight: 7,500 kg, total height: 2,600 mm, total length: 2,500 mm, total width: 2,300 mm, color: green, Equipment: CE marking, all wheel drive, cabin, lighting, pallet forks, -- USED FORKLIFTS WITH QUALITY GUARANTEE – FT LOGISTICS -- 🛠️ Years of Experience | 🧰 In-house Service & Paint Shop | 🤝 Expert Consultation | 🚛 Own Transport Fleet | 🔧 Comprehensive After-sales Support Looking for a forklift you can truly rely on? We are a reputable dealer of new and used forklifts, serving the industry for many years. Our customer base spans all of Europe—from small businesses to major industrial facilities. Our forklifts are more than just equipment—they are your assurance of seamless and dependable logistics. -- What sets us apart? -- ✅ Every forklift undergoes a thorough technical inspection and servicing (including checks, tests, oil & filter changes, and component refurbishment) ✅ Full UDT (Office of Technical Inspection) certification available on request ✅ In-house paint and service workshop—machines are optimized both technically and aesthetically ✅ Pan-European delivery—provided by our skilled drivers ✅ Operator training and on-site machine demonstration at handover ✅ Ongoing after-sales technical support—we stay connected post-purchase ✅ On-site viewing and test drives welcomed at our facility ✅ Hundreds of satisfied customers throughout Europe—become one of them today ✅ Financing options available—we collaborate with leading leasing providers ✅ Invoicing in EUR or PLN—as per your preference -- FOR SALE -- COMBILIFT C5000 – Four-Way Forklift Truck 📅 Year of manufacture: 2015 ⏱️ Operating hours: 4,963 h 🔋 Propulsion: GAS / LPG 📦 Load capacity: 5,000 kg 📏 Mast: Duplex – 4,000 mm lift height 🔩 Fork positioner – width: 1,350 mm | Forks: 1,200 mm 🛞 Superelastic tires – 100% condition 🧪 Technical condition: Excellent – fully serviced 🎨 Visual condition: Clean, corrosion-free, and ready for work 📐 Dimensions: - Lowered mast height: 2,600 mm - Total length: 2,500 mm - Overall width: 2,300 mm - Fork positioner width: 1,350 mm - Overall height: 2,950 mm -- Ideal for: -- 🏭 Narrow-aisle warehouse applications Iodpfx Asxzkppedioa 🌲 Timber, steel, and pipe handling industries 📏 Handling long and bulky loads 🏗️ Both indoor and outdoor operations -- FT Logistics – Quality you can depend on. Service you can trust. --

Condition: not inspected (used), Year of construction: 1982, machine/vehicle number: 313, tank capacity: 4,000 l, total length: 3,500 mm, total width: 1,520 mm, total height: 1,740 mm, - Mobile diesel tank with fork pocket - last inspection: 2012 Isdpfxsxugqpe Adioa - can be viewed in Zell LU, Switzerland - sold as seen, ex location +41 79 535 05 67

Condition: used, Year of construction: 1999, Technical details: turning diameter over bed: 554 mm turning dia. over face-slide: 370 mm turning length: 1000 mm centre distance: 1100 mm control: Fanuc 210i longitudinal traverse (z-axis): 1000 mm Transversal stroke (x-axis): 290 mm revolution per minute: 16 - 1800 U/min Iedpfxsv Azdwe Adioa spindle stroke: 178 mm feed:: 10 m/min. spindle passage: 104 mm spindle nose: D1 - 11 tailstock taper ISO: 6 MT spindle drive: 11/7,5 kW connection voltage: 380 V electrics - voltage/frequency: 3 Ph / 400 V / 50 Hz V/Hz total power requirement: 11 kW Weight approx.: 4,0 t dimension machine xH: 3,3 x 1,8 x 1,7 m

Condition: used, Year of construction: 2007, x-travel 560 mm y-travel 560 mm z-travel 630 mm Control MSX 701 III MAPPS Max. rpm 14.000 min/-1 power capacity - main spindel 18,5 / 11 kW max. Torque 120 Nm tool taper MAS BT 40 distance spindle center to table 80 - 640 mm distance Spindlenose and center of table 100 - 730 mm numbers of pallets 2 size of pallet 400 x 400 mm max. workpiece weight 400 kg max. workpiecediameter 630 mm max. workpiece height 900 mm change time of pallets 6,0 sec b - axis 0,001 ° Ijdpewbi Adefx Adija number of toolpositions 60 pos. tool taper MAS BT 40 max. tool diameter 70 / (140) mm max. tool length 400 mm max. tool weight 8,0 kg rapid traverse ( X / Y / Z ) 50 m/min feed speeds 0 - 50.000 mm/min Tipp feed 0 - 1.260 mm/min total power requirement 35 kVA weight of the machine ca. 9,8 t dimensions of the machine ca. 5,5 x 3,5 x 2,8 m CNC - Machiningcenter Horizontal MORI SEIKI - NH 4000 DCG - pallet-changer - Control options Program restart, cylindrical and spiral interpolation High-speed milling cycles, island and pocket milling cycles

Condition: excellent (used), Year of construction: 2018, operating hours: 40 h, machine/vehicle number: 16660, construction height: 1,330 mm, product width (max.): 1,035 mm, sweeping width: 975 mm, enginetype: Electric, manufacturer: Nilfisk Iodpsxtr Epofx Adisa