Used Biesse Rover 18 for sale (335)

Condition: used, Year of construction: 1992, Used machine Year of manufacture: 1992 Working area: X-axis: 2310 mm, Y-axis: 628 mm, Z-axis: 90 mm Max. programmable speed: X-axis: 100 m/min; Y-axis: 75 m/min; Z-axis: 15 m/min Drill holder: diameter 10 mm Spindle speed: 4000 rpm Grooving saw: diameter 120 mm Drill spindles: 4 horizontal spindles on the X-axis, 12 vertical spindles in the X-line Operating air pressure: 6 bar Maximum compressed air consumption: 0.75 NL/cycle Installed power: max. 7.5 kW Vacuum tool capacity: 40 m³/h CNC: Display: monochrome 9" Floppy disk drive PLC for machine cycle control Availability: short-term Dedpfx Asydf Ndopmocp Stock location: Röllbach

Condition: used, Year of construction: 2017, machine/vehicle number: 1000020374, functionality: fully functional, operating hours: 5,484 h, power: 12.8 kW (17.40 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: DC, travel distance X-axis: 3,280 mm, travel distance Y-axis: 1,660 mm, travel distance Z-axis: 240 mm, number of axes: 5, number of slots in tool magazine: 16, controller manufacturer: Biesse, actuation type: pneumatic, Equipment: CE marking, documentation/manual, We are selling a 5-axis machining center, Biesse Rover A 1632 Smart, manufactured in 2017. The machining center is in very good condition due to relatively infrequent use since its purchase. We are the first owner. I have attached the file "Cartellino_1000020374" to the listing below. This is a manufacturer's document describing the configuration of the offered machine according to Biesse standards. Technical specifications of the machining center: ‣ Working areas *: X = 3280 mm; Y = 1580 to 1660 mm, depending on operating conditions. Z = 200 mm (configuration with 5-axis unit, drilling head, and H=74 mm modules). Z ​​= 240 mm (configuration with 5-axis unit, drilling head, and H=29 mm modules). ‣ Configuration 2 ‣ 6 ATS tables – 18 carriages ‣ Rear row stops with 115 mm travel and 25 mm extension. ‣ Intermediate row stop located at coordinate 1190 mm with 140 mm travel. ‣ 4 side stops with 140 mm travel (2 right + 2 left) with pneumatic system. ‣ Sensor to verify stop retraction. ‣ 4 support bars for H=74 mm modules. ‣ Claw-type vacuum pump with 250 m³/h capacity. ‣ Vacuum module – Size 132x146 – H74 mm with high-friction surface and pre-installed vacuum seal. ‣ Vacuum module – Size 132x75 – H74 mm with high-friction surface, pre-installed vacuum seal, and pre-installation for locating pins. ‣ Vacuum module – Size 132x54 – H74 mm with high-friction surface, installed vacuum seal, and pre-installation for locating pins. ‣ Automatic lubrication system. ‣ Sawdust and chip removal conveyor. ‣ 5-axis interpolating machining unit, 13 kW (17.4 HP), HSK F63 tool holder, liquid-cooled. ‣ Coolant supply unit. ‣ Additional Z-carriage for machining units, controlled by an independent Z-axis. ‣ BH 17 L drilling head. ‣ 16-position rotary tool magazine on the X-carriage. ‣ 12-position linear tool magazine mounted on the machine frame. ‣ HSK F63 adapter with integrated flange for saw blades used in 5-axis units. ‣ 300 mm diameter saw blade for integrated-flange mounting. Djdpfx Ajz R I U Ispmjcp ‣ bSolid software. If the information above is insufficient, please contact me and let me know what you would like to know. Upon request, I can provide a document in English with a detailed description of our machining center's layout. Best regards, Ihor Balychev.

Year of construction: 2001, condition: ready for operation (used), Biesse Rover 22 CNC machining centre Year of manufacture 2001 SN 07498 Working range 4 axes X-axis 3060 mm Y-axis 1080 mm Z-axis 155 mm 6 consoles with 18 vacuum cup holders 4 pneumatic bakelite bars for lifting the platen Dsdpeggxihjfx Apmecp Vertical electrospindle 7,5 kW with automatic tool change, ISO 30 taper Automatic tool change 7 positions on the working head Drilling head with 20 spindles arranged as follows: 7 vertical in X-axis 7 vertical in Y-axis 4 horizontal in X-axis 2 horizontal in Y-axis Grooving saw 120mm Safety tread mats 110 m3 / h vacuum pump CE marked Weight 3500 Kg Technical specifications subject to change

Condition: used, Year of construction: 2017, The BIESSE ROVER A 1643 EDGE is a comprehensively equipped CNC machining center with a 5-axis machining head and an integrated edge banding unit. Working area, X-axis: 4,320 mm Swing machining in X: 1,620 mm Working area, Y-axis: approx. 1,580-1,660 mm Travel, Z-axis: 180 mm Edge banding Working area, X-axis: 3,300 mm Working area, Y-axis: 1,540 mm Maximum loading width in Y: 1,900 mm, expandable to up to 2,100 mm 5-axis unit 5-axis machining head C-axis: continuous 360° rotation B-axis: continuous 360° rotation B-axis speed: 18 rpm C-axis speed: 18 rpm Maximum spindle speed: 24,000 rpm Power 11 kW in S1 operation 13 kW in S6 operation Additional features Maximum undercut angle: -10° Collision monitoring for the 5-axis unit Prepared for the use of attachments on the 5-axis unit Work table and clamping system ATS work table 8 support rails 32 adjustable consoles 32 pneumatic vacuum cups Vacuum cups adjustable in 15 steps Pneumatic system divided into 2 working zones along the X-axis Vacuum system Vacuum pump capacity: 250 m³/h Additional equipment 6 lifting bars for easier loading and unloading 28 sensors for detecting lowered stops Stops and positioning 8 rear stops 8 center stops 4 side stops (2 left + 2 right) 2 additional side stops 4 removable center stops (2 left + 2 right) 2 additional center stops Pneumatic positioning and lowering of the stops Drilling unit BH 24L drilling head 13 independent vertical spindles 5 independent horizontal spindles Grooving saw, 120 mm Maximum groove depth: 25 mm Programmable spindle speed up to 6,000 rpm Tool changer 16-position rotary magazine Mounted on the X-axis carriage For tools and attachments Capacities Maximum tool/attachment weight: 7.5 kg Maximum total load of the magazine: 55 kg Edge banding unit GU60A edge banding unit For workpieces up to 60 mm thick Dcjdpfjzuwyzox Apmep Edge banding speed up to 20 m/min Double pressure roller system Glue pot with hot melt system Edge heating lamp, 600 W CNC-controlled edge feeding system Automatic edge trimming Sensor for closed geometric shapes Accessories for edge machining Edge magazine 2-roller edge magazine mounted on the X-axis carriage Maximum roller diameter: 800 mm Maximum edge height: 65 mm Additional units Rounding tool 85 mm, HSK F63 Saw unit HSK F63 for cuts and grooves Maximum saw blade diameter: 215 mm Maximum saw speed: 8,400 rpm Maximum cutting depth with a 215 mm saw blade: 68 mm Post-processing Combined glue joint and edge trimming blade units Tool sets for different edge thicknesses Software bSolid basic module 2D CAD environment Import of DXF, CIX and BPP files 3D machine simulation Tool management Management of 5-axis machining through positioning Assistant-supported program creation

Condition: good (used), Year of construction: 2024, functionality: fully functional, Biesse ROVER C 1982 CNC Machining center (5-axis) Description; Working fields X = 8125 mm; Y =1950 mm Z= 470/500 mm UPS Closed chain cable holder X-axis 12 ATS Panel supports 48 sliding bases Pneumatic locking system in 2 work areas in X 8 aluminium lifting bar supports for loading ease of large and heavy pieces. 290 m3/h rotary claws vacuum pump Vacuum module - Size 132x146 - H74mm Vacuum module - Size 132x75 - H74mm Vacuum module - Size 132x54 - H74mm Belt conveyor for the removal of chips and off-cuts 21.6 kW (29.4 HP) operating unit with 5 interpolating axes HSK F63 adaptor and liquid cooling Suction hood with continuous positioning in Z controlled by NC Air-Jet cooling system Liquid chilling unit for liquid cooled systems Chain tool changer with 22 places at 180 mm centerdistance Strengthened gripper PC bTouch Presetter for the measurement of the tool length with diameter up to 130 mm bSolid 3D CAD-CAM program Additional license for bSolid Additional filter for vacuum pump Dedpfxe Af Ii No Apmscp SOPHIA - IoT Connection Roller lifting support in replacement of the standard one Enlargement of mesh guards and movement of the doors from front side to rear side to load profiles with length up to 11 meters (Despite our great care all changes, mistakes in technical data, prices and all information is subject to (typing) errors. No guarantee on printed data! Availability subject to prior sales). (Trotz größter Sorgfalt bleiben Änderungen, Irrtümer bei technischen Daten, Preisen und allen Angaben (Tipp-)Fehler vorbehalten. Keine Gewähr auf gedruckte Daten! Verfügbarkeit vorbehaltlich Zwischenverkauf). Prices excl. advertisement cost MachineSeeker / Preise exkl. Inserierungskosten MaschinenSucher Best woodworkingmachines from the Netherlands Holland Die besten holzbearbeitungsmaschinen aus die Niederlande De beste gebruikte machines uit Nederland

Condition: used, Year of construction: 2013, functionality: fully functional, CNC machining center Biesse Rover A 4.30 with accessories and tools, see photos. Year of manufacture 2013, fully equipped and in perfect working order. Includes a lock box unit, saw unit, and disc changer with 24 positions. Includes Palettcad software. From an insolvency, therefore no further technical data available. Please submit a bid. Location: Freising. Dcsdpfxj Aaz Svs Apmsp Inspection is welcome. We have other used machines available. Simply contact us.

Condition: good (used), Year of construction: 2018, machine/vehicle number: 1000028154, functionality: fully functional, Equipment: rotational speed infinitely variable, The machine was commissioned in 2019, single owner. It has seen very little use. Description Useful working area, 5-axis configuration: X=3280mm, Y=1600mm Axis travel: X=3706mm, Y=2294mm, Z1=515mm, Z2=371mm Axis traverse speed: X=80m/min, Y=60m/min, Z=30m/min Electrospindle: HSD, 5 axes 11 kW, with continuous 360° rotation on B and C axes, enabling high-precision machining of complex shapes liquid-cooled Dcodpfxsxdl H Uj Apmjp Drilling head: HSD 20 vertical spindles 4 horizontal spindles grooving discs on X-axis grooving discs on Y-axis Work table: 6 cross beams Isbjwhypnjni Itxtobb 4 suction cups per beam preparation for uniclamp Tool magazines: 16-position revolver-type tool changer Vacuum system: Vacuum pump with a capacity of 250 m³/h, ensuring firm clamping of the parts during processing

Condition: ready for operation (used), Year of construction: 2016, machine/vehicle number: 1000012445, functionality: fully functional, travel distance X-axis: 3,600 mm, travel distance Y-axis: 1,800 mm, overall weight: 4,000 kg, TECHNICAL DETAILS Dedjydk Aiepfx Apmocp Working area X-axis: 3,600 mm Working area Y-axis: 1,800 mm Number of working zones: 2 Tool change positions on the rear: 16 Tool change positions on the machine: 8 Vacuum pump: 250 m³/h Drilling head BH 10 configuration: 15 vertical spindles on the X-axis 17 vertical spindles on the Y-axis MACHINE DETAILS Electrospindle power: 13.2 kW Electrospindle type: ISO 30 Control: CNC with B-Solid software Weight: 4,000 kg EQUIPMENT Nesting work table Automatic loading system with side lift table Label printing system with automatic application on the loading table Panel separation system with suction cups Automatic unloading system with motorized conveyor belt Worktable cleaning system Protection and safety system with perimeter fencing Safety system with bumper Automatic lubrication system Air-conditioning system for cooling and cleaning the machine control unit

Condition: used, Year of construction: 2008, input voltage: 400 V, input frequency: 50 Hz, number of slots in tool magazine: 8, Equipment: CE marking, Biesse Rover ROVER A 3.40 FT K2 CNC machining centre Description Working fields: X = 3685 mm; Y = 1290 mm; Z = 160 mm The composition includes: Automatic lubrication system FT Work Table 4 front stops + 4 back stops equipped with pneumatic system and sensors. 4 side stops equipped with pneumatic system and sensors. Vacuum tank Vacuum system for 2 300 m3/h pumps 300 m3/h rotary claw vacuum pump 12 kW (16.1 HP) Electrospindle with ISO 30 adaptor, air cooled Blowing unit Flange for the assembly of aggregates on the electrospindle Prearrangement for operating device with 360° interpolation and gear transmission. Boring head BH 21 L Revolving tool changer with 18 places Prearrangement for the assembly of the automatic unloading device for nested-based machined panels Controls on remote keyboard Numerical Control XP600 User-friendly interface BIESSEWORKS - Advanced programming system BIESSE NEST Module Air conditioner for electric cabinet Inverter Safety devices with 2 mats and low fencing CE (Despite our great care all changes, mistakes in technical data, prices and all information is subject to (typing) errors. No guarantee on printed data! Availability subject to prior sales). (Trotz größter Sorgfalt bleiben Änderungen, Irrtümer bei technischen Daten, Preisen und allen Angaben (Tipp-)Fehler vorbehalten. Keine Gewähr auf gedruckte Daten! Verfügbarkeit vorbehaltlich Zwischenverkauf). Prices excl. advertisement cost MachineSeeker / Preise exkl. Inserierungskosten MaschinenSucher Best woodworkingmachines from the Netherlands Holland Dcodpfx Apozqdqlemop Die besten holzbearbeitungsmaschinen aus die Niederlande De beste gebruikte machines uit Nederland

Condition: used, Year of construction: 2016, CNC machining center Manufacturer: Biesse Type: Rover A 1643 Year of manufacture: 2016 Technical data - 5-axis machine - Working area X/Y: approx. 4320 - 1620 mm Dedpfx Apj Ad Iw Hjmscp Main spindle - Rated current: 14 kW - Power, short-term: 16 kW (S2 1 min.) - Maximum speed: 20,000 rpm - Tool clamping system: HSK-F63 - Cooling: as liquid - Operating mode: S1 continuous operation Drilling unit - Maximum motor speed: 6000 rpm - Vertical spindle stroke: 60 mm - Horizontal spindle stroke: 75 mm - Spindle bore: 10 mm - Saw blade diameter: 80 - 120 mm Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2016, CNC machining center Manufacturer: Biesse Type: Rover A1432 Djdpfxs Ad Iw Ts Apmecp Year of manufacture: 2016 Technical data 3-axis machine HSD drilling head - Maximum motor speed: 6,000 rpm - Vertical spindle travel: 60 mm - Horizontal spindle travel: 75 mm - Spindle bore: 10 mm - Saw blade diameter: 80-120 mm Drive power: 17.3 kW Note: The technical data and descriptions are copies of the original order confirmation. The information provided is for informational purposes only and is non-binding.

Condition: excellent (used), 200030A) C.N.C. WORKING CENTER "NESTING" with 3-axes "BIESSE" Mod. Rover A - FT 1531 Gantry-drive (axe X) machine Numerical Control with Software bSolid (3D CAD-CAM) + bNest Safety cabin (enclosure) of the working head Bumper Unique flat working table FT Automatic Tools Changing System with Tools storage plates Storage (revolver-type) with 8 folds (on Y-axe) Max. useful working area (X - Y - Z) mm 3100 x 1560 x 60 Vacuum pump 1 x 300 m3/h Separate electric and command cabinet WORKING GROUPS (TOP): No. 14 independent vertical boring spindles (7 in X + 7 in Y) No. 4 independent horizontal boring spindles (2 in X + 2 in Y) Drilling head BH 18 motor-power (Kw) 3 ca. No. 1 vertical Electro-spindle HSK F63 (Kw) 13,2 Dcodjzygiiopfx Apmsp 200030B) UNLOADING with roller conveyor (length approx. 3,500 mm)

Condition: excellent (used), "NESTING" CELL with 3-axes (X-Y-Z+ C-axis capability) CNC working Center, composed by: 200029A) AUTOMATIC LOADING/IN-FEEDING SYSTEM (type A 1563) also for thin panels, with scissor table, movable arm (NC positioning Sweeping Arm) with vacuum suction cups, 200029B) CNC "nesting" 3-axes (flat table) "BIESSE" Mod. Rover A - FT 1531 Gantry-drive (axe X) machine Numerical Control (WRT) with Software bSolid (3D CAD-CAM) + bNest (SOPHIA - IoT Connection) Safety cabin (enclosure) of the working head Bumper Unique flat working table FT Djdpfx Ajzxrnbspmjcp Automatic Tools Changing System with two (2) Tools storage plates 1st Tools storage plate with 16 folds (on X axe) + 2nd storage (revolver-type) with 8 folds (on Y-axe) Max. useful working area (X - Y - Z) mm 3100 x 1560 x 170 No. 8 Working areas (Multizone) - No. 3 Vacuum pumps (capacity 250 m3/h each) Separate electric and command cabinet - Total installed power (Kw) 31,21 WORKING GROUPS (TOP): No. 14 independent vertical boring spindles (7 in X + 7 in Y) No. 4 independent horizontal boring spindles (2 in X + 2 in Y) Drilling head BH 18 motor-power (Kw) 3 ca. No. 1 vertical Electro-spindle HSK F63 (Kw) 13,2 200029C) AUTOMATIC OUT-FEEDING SYSTEM (type 1531) with motorised belt (length mm 3740)

Condition: used, Year of construction: 2014, Main spindle power: 13.2 kW Drilling unit motor power: 7 kW 3-axis machine Drilling unit: Technical data - Nut saw - 2 horizontal drilling spindles in the X-axis (left/right) - 1 horizontal drilling spindle in the Y-axis (left/right) Djdpfx Aezuwxdjpmecp - 10 vertical drilling spindles

Condition: used, machine/vehicle number: 008562, X axis working area: 2465 mm Y axis working area: 1260 mm Dodozvwiljpfx Apmocp Working Table: Flat table Main Electrospindle power: 13.2 KW Number of controlled axes: 3 axes Total number of drilling spindles: 10 Total number of tool changer positions: 16

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, Work area X: 4580 mm Work area Y: 1850 mm 5-axis electrospindle Number of drilling heads for vertical drilling: approx. 24 Number of drilling heads for horizontal drilling X: 4 Number of drilling heads for horizontal drilling Y: 2 33-position chain-type tool changer Dcedpo Ah R Eijfx Apmep 1-position tool changer for saw blades Worktable with 8 rails Software: BiesseWorks Remote control panel 1 vacuum pump with a capacity of 250 m3/h Chip conveyor belt Safety mats Lateral safety guards Includes suction cups, some Uniclamps, and some HSK collets.

Condition: good (used), Year of construction: 1998, I sell the 3-axis CNC working centre Biesse Rover 13S with beam table, year 1998. Configuration: 3-axis main spindle HSD 1 grooving saw X-direction Drilling head 10+4+2 spindles Useful working area 1540x1050mm. 1 working field, 2 clamping areas Total power 10kW Pump Becker Additional vacuum outputs for raster works or connection of additional clamping devices. Dcsdpfxoz Ii Axs Apmep Good condition. Available immediately.

Condition: excellent (used), Year of construction: 2011, machine/vehicle number: 95566, functionality: fully functional, controller model: BIESSE XP 600, working width: 1,287 mm, spindle speed (max.): 24,000 rpm, working height: 170 mm, working length: 5,920 mm, TECHNICAL DETAILS Working area X: 5,920 mm Working area Y: 1,287 mm Working area Z: 170 mm C and A axes: available Working areas for pendulum machining: 2 Work table: ATS-HTS-EPS Automatically positionable consoles: 10 units Stop pins per console: 2 units 5-axis milling spindle Spindle power: 9 kW / 11 kW at 60 Hz Speed: max. 24,000 rpm Tool holder: HSK-F63 Cooling: Liquid cooling Drilling head BH 26 Vertical drilling spindles: 16 units Horizontal drilling spindles in the X direction: 4 units Nut sawing units: 2 units Tool slots: 21 units Tool changer type: Chain tool changer MACHINE DETAILS Dcsdpj Ah Rhqofx Apmep UNICLAMP clamping systems: 6 units Control system: BIESSE XP 600 Motor power: 5.5 kW Conveying capacity: 244 / 286 m³/h Compressed air: 7–7.5 bar Total power: 25.3 kW Machine weight: 4,200 kg EQUIPMENT Automatic console positioning system EPS Pendulum machining with two working areas ATS-HTS-EPS work table Liquid-cooled 5-axis milling spindle Drilling head BH 26 Nut sawing units for X and Y directions Chain tool changer 6 UNICLAMP clamping systems Motorized conveyor belts for chips and machining waste BECKER vacuum pump Numerous vacuum suction cups Numerous HSK-63 tool holders 2 large saw blades in the tool magazine

Condition: used, Year of construction: 2019, functionality: fully functional, operating hours: 3,900 h, workpiece length (max.): 4,320 mm, workpiece width (max.): 1,620 mm, number of axes: 5, overall weight: 4,500 kg, !!Decide quickly and secure a bargain!! Technical specifications: Year of manufacture: 2019 Operating hours: approx. 3,900 Working area X / Y: 4,320 × 1,620 mm 8 consoles with automatically adjustable vacuum cups Triple zero line in Y (total of 3 stop points) 5-axis HSD milling spindle with liquid cooling Separate drilling head with grooving units in X and Y Automatic tool changer with two tool magazines Dcjdpfxo Afaapj Apmjp Control station with screen and manual control unit NC HOPS software, version 7.5 Machine weight: approx. 4,500 kg Includes a wide range of tools, frame clamps, suction cups, and accessories!

Condition: used, Year of construction: 2001, Equipment: CE marking, Biesse Rover ROVER 24 FT CNC machining centre Description The work surface consists of a grid table consisting of two phenol tables with a size of 1540 x 1250 mm that can be linked. The grid table has a grid of 30 mm and vacuum openings of 9 mm in a grid of 150 mm in the X and Y-richting. The grid table is equipped with 6 pneumatic zero point cams at the rear and 1 on the left and right sides. • The working range of the machine is 3100 x 1300 x 155 mm. (Z-stroke 250 mm ) • The speed on the X-axis is programmable between 0 and 100 m/min. • The speed on the Y-axis is programmable between 0 and 100 m/min. • The speed on the Z axis is programmable between 0 and 15 m/min. • The three axes are driven by brushless digital DC servo motors. CNC numerical control type NC-500 Milling motor with automatic change system with ISO30. The power of this milling motor is 10.5 hp at 24,000 rpm 10-position tool changer that moves with the unit Drilling unit with fourteen independent drill spindles Groove saw Static frequency converter Centralized pneumatic system Centralized lubrication system Vacuum pump with a capacity of 250 m3/hour Two push-button control panels Working pressure for air 6 kg/cm2. Voltage 380 Volt, 50 Hz. Djdozqtztspfx Apmocp Safety mats on the front. CE (Despite our great care all changes, mistakes in technical data, prices and all information is subject to (typing) errors. No guarantee on printed data! Availability subject to prior sales). (Trotz größter Sorgfalt bleiben Änderungen, Irrtümer bei technischen Daten, Preisen und allen Angaben (Tipp-)Fehler vorbehalten. Keine Gewähr auf gedruckte Daten! Verfügbarkeit vorbehaltlich Zwischenverkauf). Prices excl. advertisement cost MachineSeeker / Preise exkl. Inserierungskosten MaschinenSucher Best woodworkingmachines from the Netherlands Holland Die besten holzbearbeitungsmaschinen aus die Niederlande De beste gebruikte machines uit Nederland

Condition: used, Year of construction: 2018, Numerical Control BH 660 with BIESSE BSolid software bEdge module for edge management bSolid surface design Sophia - IoT Connection Office control Working range on X-axis mm 3228 Working range on Y axis mm 1580 Working range on Z axis mm 200 with H74 mm suction cups Working range on Z axis mm 245 with H29 mm suction cups No. 8 adjustable ATS panel support bars Installation of the pneumatic lock divided into two zones in Y No. 6 Pneumatic Bakelite bars for panel lifting No. 3 adjustable suction cups for bar Set-Up Assistant for Suction Cups No. 1 electrospindle (pantograph) with 4 axes, automatic tool change, KW 13 (HP 17.4) motor, cooling liquid, HSK cone attachment, 20000 RPM Automatic tool change with 16 positions on the X-axis of the carriage Drilling tesa BH17 independent spindles arranged as follows: No. 5 independent spindles for vertical drilling in the "X" direction No. 5 independent spindles for vertical drilling in the "Y" direction No. 4 spindles for horizontal drilling in the "X" direction No. 2 spindles for horizontal drilling in "Y" direction No. 1 blade integrated into the drilling head diam 120 mm (useful cut 25 mm) GU60L gluing unit for EVA glue with pre-melter - edge pressure system with double rubber roller for spokes Dcedpfjugpwnex Apmjp maximum internal 30 mm and edge joint sensor - 500 ml glue pot installed on the glue roller - lamp edge heating - edge feed system - edge cutting system - possibility of Introduction of the manual edge Plastic edge thickness from 0.4 to 3 mm Wood edge thickness from 0.4 to 2 mm Laminated edge thickness from 0.4 to 1.2 mm Maximum edge width 65 mm Workpiece thickness from 10 to 60 mm Minimum internal radius workable with 30 mm edging Maximum external radius for edging, proportionate to the thickness and stiffness of the edge: * 10 mm with edge up to 1 mm thick * 20mm with 2mm thick edge * 30mm with 3mm thick edge Minimum dimensions of the edging panel 300 x 300 mm Minimum internal diameter for edging: 350 mm with plastic edges less than 1 mm thick and with panel maximum thickness 18 mm 2-position edge storage unit positioned inside the protective casings for edges with maximum thickness 65 mm Finishing aggregate cleaning station with automatic dispensing of special cleaning liquids and with a cleaning cycle No. 1 aggregate for edge trimming / rounding No. 1 EF60A combi aggregate trimmer / edge scraper / glue scraper Perimeter protection grids Chip evacuation system with motorized belt Liquid cooling system Automatic lubrication system No. 1 vacuum pump of 250 m3/h TECHNICAL DETAILS TO BE CONFIRMED

Condition: used, Year of construction: 2019, Numerical control with bSolid software The multi-document software application in Windows environment allows the design of the finished product, the definition of its processes, the definition of the work plan, the simulation of the piece machining operations on the 3D model of the machine and generation of the necessary machine programs. bSolid - 3-Axis Machining bSolid - 5-Axis Machining Module for surface machining with 5-axis units and interpolation movements on all 5 available axes (X,Y,Z,C,B). The module includes the following commands: · assignment to surfaces three-dimensional roughing and finishing operations · spread or project a path onto a curved surface machining lying on a plane · follow 2D or 3D curves with any type of tool bSolid - 3D Engraving bSolid - Import external formats Fields of work: X = 5055 mm; Y = 1650 mm (may vary depending on configuration) Z = 200 mm with modules H=74 mm Z = 245 mm with modules H=29 mm Loadable piece in Y: * 1650 mm, with thickness up to 60 mm on H=74 mm modules * 1600 mm, with thickness over 60 mm on H=74 mm modules. 10 ATS floors – 40 trolleys The code includes: • 2 aluminium bars (n. 1 left and n. 1 right) on which the lateral stops slide. • 10 aluminum worktops. The worktops slide on hardened and ground linear guides using recirculating ball bearing slides. Locking occurs on both linear guides, front and rear, by means of four pneumatic cylinders. The control is activated by a button located in front of the work surface. The carriages slide on steel guides positioned above the extrusion. Pneumatic locking system divided into 2 locking zones in X Automatic positioning (EPS) for worktops. "EPS" (Electronic Positioning System) device for the automatic positioning by NC of the work surfaces and trolleys complete with locking devices capable of eliminate possible operator errors. Rear row stop, with 140 mm stroke Intermediate row stop, positioned at 405 mm, with 140 mm stroke. Front row stop, positioned at 1460 mm, with 140 mm stroke 4 lateral stops, with 140 mm stroke (2 right + 2 left) with system 2 additional side stops, with 140 mm stroke (1 right + 1 left). Sensor for checking whether the stops have descended 12 clamping devices for clamping narrow workpieces 6 loading aid bar lifts, for H=74 mm modules Configuration 5A, for Rover B. Configuration for high productivity and flexibility, thanks to the two operating groups 4 and 5 axes and the possibility of performing tool changes in concurrent time. It includes the axes and carriages for the movement of the main operating groups. Includes 2 inverters. Second Y-axis. Introduces the separation of the front and rear Y-carriages, with independent motorization. The two Y-carts have a maximum speed of 118 m/min. 13.2 kW (17.7 HP) electrospindle, HSK F63 connection, air-cooled. Main features: • 11 kW (14.7 HP) from 12,000 to 15,000 rpm in S1 service. • 13.2 kW (17.7 HP) from 12,000 to 15,000 rpm in S6 service. • Bearings ceramics. • Right and left rotation. • Rotation speed from 1,000 to 24,000 rpm programmable by NC. • The release pneumatic operation is carried out via a prismatic linear guide and recirculating ball bearings. A cover is included for chip extraction, with 6 different positions in Z managed by the NC, depending on the length of the tool, or by program. The suction mouth is automatically closed when the electrospindle is not working. Provision for subsequent installation of the 360° operating group (C-axis) Revolver tool maga... Dcjdpfx Asw D E A Espmep

Condition: used, Year of construction: 2005, 2005 BIESSE ROVER B 4.40 FT 3-axis CNC machining center Technical features in the last photo Engine hours on: 45,343 Dcodpfxjy Ud Sgo Apmsp Machine hours in automatic operation (work): 27,267

Condition: used, Year of construction: 2013, power: 17.1 kW (23.25 HP), input voltage: 400 V, input current: 29 A, input frequency: 50 Hz, travel distance X-axis: 4,320 mm, travel distance Y-axis: 1,326 mm, travel distance Z-axis: 170 mm, number of axes: 5, number of slots in tool magazine: 33, Equipment: CE marking, Biesse Rover A 1343 CNC machining centre 5-Axis Description Rover A ATS CNC Machining Centers Dedpfey U Naijx Apmscp Working ranges X = 4,320 mm; Y = 1. 326 mm;Z = 170 mm Waste conveyor belt Automatic lubrication system Remote console 1 x 250 m3/h vacuum pump for standard system Auxiliary vacuum system for double working area machine Multi-zone 8 bars and 24 cups with automatic positioning (ATS-EPS X-Y) 8 reference stops with 115 mm rear stroke 8 front reference stops with 140 mm stroke positioned at a height of 1190 mm from the rear stops 4 side stops, with 140 mm stroke (2 right + 2 left) with implant 2 additional side stops, with 140 mm stroke (1 right + 1 left) Pneumatic system for panel lift Coolant control unit to replace the heat exchanger supplied with 13kW 5-axis units. Operating unit 5 interpolating axes 13 kW (17.4 Hp), HSK F63 connection, liquid-cooled. BiesseWorks Advanced Machine Chain tool magazine with 33 places - centre distance 120 mm (Despite our great care all changes, mistakes in technical data, prices and all information is subject to (typing) errors. No guarantee on printed data! Availability subject to prior sales). (Trotz größter Sorgfalt bleiben Änderungen, Irrtümer bei technischen Daten, Preisen und allen Angaben (Tipp-)Fehler vorbehalten. Keine Gewähr auf gedruckte Daten! Verfügbarkeit vorbehaltlich Zwischenverkauf). Prices excl. advertisement cost MachineSeeker / Preise exkl. Inserierungskosten MaschinenSucher Best woodworkingmachines from the Netherlands Holland Die besten holzbearbeitungsmaschinen aus die Niederlande De beste gebruikte machines uit Nederland

Condition: used, Year of construction: 2009, Biesse Works Control Working range on X axis mm 3500 Working range on Y axis mm 1585 Working stroke in Z axis mm 350 N ° 2 work fields Bar worktop No. 8 adjustable bars N° 4 pneumatic Bakelite bars for lifting the panel No. 3 adjustable suction cups for each bar with vacuum seal for fixing the panel during processing No. 1 4-axis vertical electrospindle (Vektor), with automatic tool change, HSK type cones 10-position rotary tool change system on the operating head 24-position chain tool change system - located on the rear of the chain machine Drilling head with vertical and horizontal spindles composed as follows: n. 12 vertical spindles in X n. 12 vertical spindles in Y n. 6 horizontal spindles in X n. 4 horizontal spindles in Y n. 1 independent blade for making X-grooves Front protection and safety system with carpets Perimeter protection grids Chip evacuation system with motorized belt Air conditioning system for cooling and cleaning of machine control Vacuum pump 250mc/h TECHNICAL DETAILS TO BE CHECKED Dsdpfx Ajw D Dhaopmjcp