Used Cantilever for sale (387)

Condition: new, 1860 m³/h Pressung 2.900 Pa 1,1 kW filter surface area 10 m² 72 dB(A) 400/50 V/Hz 665 x 1100 x 1495 mm 200 kg - Hose arm 3 m, joints inside - Filter cartridge: dust class M - Pre-filter: baffle plate - Current type: 3Ph+N+PE The filter system ----- The mobile filter system of the Cartmaster IFA type is thanks to the automatic Cleaning particularly suitable for welding work with unalloyed and alloyed steels, galvanized material and aluminum with heavy smoke development. Nlsdpfx Aashp S Trezeg It corresponds to the safety requirements for devices Welding fume class "W3" (high-alloy steels with alloy components > 30% Nickel-based alloy).If used as intended, the system can be used for the Recirculation mode used because the requirements for the Exceptions according to TRGS 560 are fulfilled. That special developed, dirt-dependent cleaning system ensures a good cleaning behavior of the filter cartridge, so that an optimal suction performance is guaranteed throughout the operation. The cleaned particles fall into a dust collection drawer from which they can then be disposed of. The powerful spiral fan ensures even with saturated Filter cartridges for a high volume flow. The filter media ----- A baffle serves as a pre-separator for coarse particles. The filter cartridge installed below (dust class M, degree of separation > 99%) filters the finest smoke and dust particles. The cartridge is factory coated which increases the service life. The extraction arm ----- The extraction arm can be moved with the 3 internal joints Position spring support slightly and is in the set position cantilevered. A throttle flap integrated in the extraction hood enables the Flow rate setting.

Condition: new, 1860 m³/h Pressung 2.900 Pa 1,1 kW filter surface area 10 m² 72 dB(A) 400/50 V/Hz 665 x 820 x 1365 mm 165 kg mobile extraction, welding fume extraction (manual cleaning by loss of pressure) - Hose arm 3 m, joints inside - Filter cartridge: dust class M - Particle pre-separator: baffle plate - Current type: 3Ph+N+PE The filter system ----- The mobile filter system of the type StrongMaster IFA is particularly suitable for Welding work with unalloyed and alloyed steels, galvanized material and Aluminum in case of heavy smoke development. She corresponds to the Safety requirements for devices in the welding fume class "W3" (high-alloy steels with alloy components > 30% nickel-based alloy). When used as intended, the system can be used for be used in the recirculation mode, since the requirements for the Exceptions according to TRGS 560 are fulfilled. The filter will via a maintenance door using a compressed air gun from the clean air side cleaned. The cleaned particles fall into a dust collection drawer from the they can then be disposed of. The powerful scroll fan ensures a high volume flow even with saturated filter cartridges. The filter media ----- A baffle serves as a pre-separator for coarse particles. The filter cartridge installed below (dust class M, degree of separation > 99%) filters the finest smoke and dust particles. The cartridge is factory coated which increases the service life. The extraction arm ----- The extraction arm can be moved with the 3 internal joints Position spring support slightly and is in the set position cantilevered. A throttle flap integrated in the extraction hood enables the Nsdpekm Rynsfx Aazolg Flow rate setting.

Year of construction: 2009, condition: used, Apple 15 head depositor Model: CCP12 Nodpfjb Ucwkox Aazolg Stainless cantilever framed 15 head machine

Condition: used, Year of construction: 2018, CNC-CONTROLLED MACHINING CENTER AUTHOR M 200 AUTHOR M200 3710x1620 Z250 - CNC-controlled machining center 1 Technical data Work area I.M.S. I.U. Work area X-axis 3710 mm * 146" * Work area Y-axis 1620 mm * 63¾" * Workpiece passage Y 1900 mm 74¾" Workpiece passage Z 250 mm 9¾ Workpiece length for pendulum machining 1700 + 1700 mm 67" + 67" Travel speed of the X-Y axes PRO-SPACE 56 m/min 184 ft/min Travel speed of the X-Y axes PRO-SPEED 78 m/min 256 ft/min * Distance covered by all tools in the X and Y direction; see the corresponding layout for further details. With a 5-axis motor, the dimension in Y increases to 1680mm (66"), for motor JQX or 1720mm (67½") for motor KS/KT max. Width of the loadable plate for horizontal drilling, electric spindle only oriented vertically, no central reference stops Installation data I.M.S. I.U. Installed power 23 - 28.5 KVA Electrical standard specifications 400 Voltage 50 Hz 3 phases Air consumption 450 Nl/min Compressed air consumption 4500 m³/h 2650 CFM Extraction air velocity 30 m/sec Extraction nozzle diameter 250 mm 9.8 Inches Noise level VSA * LAV * Drilling 72.2 74.6 Milling 74.3 80.7 Reference standard EN ISO 11202:1995* VSA = unloaded and without extraction * LAV = in operation with extraction Structure of the base body: The CNC machining center can be equipped flexibly with different milling units as well as multi-spindle drilling heads and many other units, up to dowel drilling units. In order to meet all requirements in the field of wood and plastic processing, as well as the demands of the users, each machine can be equipped with 3, 4 or 5 machining axes. The selection of drilling units extends to up to 34 drilling spindles with an integrated groove saw for the back panel groove or rabbet machining. The possibility of using this high-quality CNC machining center both as a cantilever table machine and with an aluminum grid table underscores the flexible range of applications and the performance of the M100 and M200 series. Powerful drilling heads, with individually selectable drilling spindles, max. RPM 8,000, and implemented in . technology, "the most robust drilling spindles on the market", with more than 1,000 maintenance-free application hours (lubrication interval of the drilling spindles). The possibility of being able to replace the drilling spindles within a very short time, "even without a technician", through the technology, without disassembling the drilling gear, sets a benchmark in the industry and is already standard on your machining center. Imagine your CNC machine performing hinge drilling in just one drilling operation (option), instead of the usual 3. An option that underscores our claim to offer you robust and high-performance units on our machines. Ideally and flexibly equipped for a wide variety of requirements. Whether manual or automatic, the FLEX cantilever work table allows vacuum cups and mechanical clamping elements, such as pneumatic clamps for window or curtain wall constructions (option), to be quickly, safely and cost-effectively adjusted to any material and clamping requirements, making your day-to-day work easier. Differently sized vacuum cups and clamping elements, which were developed in close cooperation with customers and users, are available as an option. Nedpfx Aajzvhkyszolg

Condition: new, Year of construction: 2025, Laser source: Raycus or Max: 4/6/8/12 kW Laser head: 3D BOCI Control system: FSCUT 5000 A Chuck: 20-450 mm Loading/unloading: 12000 mm X/Y axes Positioning accuracy: ±0.05/1000 mm Repeatability: ±0.03/1000 mm Acceleration: 0.8g (m/s²) Rotational speed: 60 rpm Max. positioning speed: 60 m/min Max. weight of a tube: 1500 kg 1. Raycus 6000W laser source 2. BEVEL laser head Nlodpfji Apfzex Aazsg 3. Welded frame DPL 4. Schneider electrical components 5. Helical rack KH 6. Techmech reducer 7. Yaskawa servomotor 8. SHAC guides 9. Integrated power control 10. FScut 5000 software 11. Integrated electrical cabinet 12. HANLI water chiller 13. Cantilever gantry axis-X FHBS 14. Automatic waste collection 15. Crawler-type automatic workpiece collection 16. Automatic support system 17. Loading frame 12000 mm 18. Unloading frame 12000 mm

Condition: good (used), Technical specifications for the securing bolt: System: Elvedi Type: HRZ 15 Included in delivery: 1x securing bolt, used for cantilever rack Material color: galvanized Dimensions: 178 x 24 x 17 mm (LxWxH) Weight: 0.660 kg/piece For securing the cantilever arms against accidental lifting Currently in stock: approx. 350 pieces The stated price corresponds to the pickup price including VAT. Njdpowdvzlofx Aazslg Your contact persons in our company: Mr. Andre Evening Mr. Mario Klöver Mr. Falk Deutsch General information about the item: This item is available for pickup only. Any additional transport or shipping of this item is subject to additional costs, which can be requested separately depending on the delivery location or scope of delivery.

Condition: new, Radial drilling machine with hydraulic clamping and thread cutting device. Technical data: Drilling capacity steel Ø: 50 mm Drilling capacity cast iron Ø: 60 mm Thread cutting steel Ø: 40 mm Thread cutting cast iron Ø: 50 mm Diameter of the column: 320 mm Projection (min/max): 330 - 1650 mm Travel of the spindle head (horizontal): 1320 mm Distance spindle nose - base plate (min/max): 465 - 1405 mm Travel height of the cantilever: 670 mm Clamping surface cube table: 630 x 500 x 500 mm Base plate size: 2550 x 970 x 200 mm Spindle holder: MK 5 Spindle stroke: 270 mm Speeds: (12) 37 - 1253 1/min Feed rates: (3) 0.06 / 0.10 / 0.20 mm/rev Nlodpfx Asuxrtfoazeg Motor power, approx.: 3.7 kW Max. total height: 2790 mm Weight, approx.: 3300 kg Features: - Simple one-button operation with integrated circuit for automatic release of swing arm movement, automatic stop and automatic clamping. - Boom arm and drill head with independent hydraulic clamping - A special lifting safety device prevents the arm from dropping abruptly or moving on its own, even after a long period of use and corresponding wear. This safety device protects the operator from injury, even if the threaded nut is excessively worn. - The column, arm and gearbox can be clamped simultaneously by pressing a button. Standard equipment: - Tapping device - Coolant device incl. pump - Machine light - Cube table 635 x 520 x 420 mm - Operating tools in box - Operating instructions and spare parts list - Protective device for spindle - CE

Condition: new, Technical data: Drilling capacity steel Ø: 50 mm Drilling capacity cast iron Ø: 60 mm Tapping steel Ø: 40 mm Tapping capacity cast iron Ø: 50 mm Diameter of the column: 300 mm projection (min/max): 305 - 1275 mm travel of the spindle head (horizontal): 970 mm distance spindle nose - base plate (min/max): 438 - 1330 mm Traverse height of the cantilever: 625 mm Nlsdpfx Aop Atipoazsg Clamping surface of cube table : 635 x 520 x 420 mm size base plate : 1830 x 785 x 185 mm spindle mounting: MK 5 spindle stroke: 270 mm Speeds: (12) 44 - 1206 min-1 feeds: (3) 0.06 / 0.10 / 0.20 mm/rev. Motor power, approx.: 3,7 kW Total height, max.: 2795 mm Weight, approx.: 2300 kg Features: - Simple one-button operation with integrated circuit for automatic release of swing arm movement, automatic stop and automatic clamping. - Boom arm and drill head with independent hydraulic clamping. - A special lift safety device prevents the arm from falling off abruptly or moving on its own, even after a long period of use and corresponding wear. This safety device protects the operator from injury even if the threaded nut is excessively worn. - The column, arm and gearbox can be clamped simultaneously by pressing a button. Standard Equipment: - Threading device - Coolant device incl. pump - machine light - cube table 635 x 520 x 420 mm - Operating tools in box - Operating instructions and spare parts list - protection device for spindle - CE

Condition: excellent (used), Year of construction: 2018, measuring range X-axis: 500 mm, measuring range Y-axis: 500 mm, measuring range Z-axis: 500 mm, workpiece weight (max.): 100 kg, The system was hardly used (the order was cancelled). Nsdpfxjzb U Has Aazjlg CMM DuraMax 5/5/5 ZEISS CNC coordinate measuring machine (CMM) with cantilever design. Maximum permissible length measuring deviation (MPE) according to ISO 10360-2:2009: - MPE_E0 (3D) = (2.4 + L/300) µm for 18 - 22 °C - MPE_E0 (3D) = (2.7 + L/250) µm for 18 - 26 °C - MPE_E0 (3D) = (2.9 + L/200) µm for 18 - 30 °C Maximum permissible scanning probe deviation (MPE) according to ISO 10360-4:2000 within the maximum permissible scanning test duration (MPT). MPE_THP = 2.9 µm within MPT_tau = 55 s. Single probe deviation form according to ISO 10360-5:2010. MPE_PFTU = 2.4 µm. Form measuring deviation according to ISO 12181:2011 (VDI/VDE 2617 Part 2.2). MPE_RONt (MZCI) = 2.4 µm.

Condition: ready for operation (used), Year of construction: 2022, machine/vehicle number: 30B.11.040.22, functionality: fully functional, TECHNICAL DETAILS Working area, X-axis: 3,300 mm Working area, Y-axis: 1,280 mm Working area, Z-axis: 250 mm Travel, X-axis: 4,000 mm Travel, Y-axis: 1,670 mm Travel, Z-axis: 500 mm Milling spindle Number of milling spindles: 1 Max. spindle speed: 24,000 rpm Main motor power: 11 kW Tool clamping system: HSK-F63 Table design: Cantilever table Table length: 3,300 mm Table width: 1,280 mm Material clamping: Pneumatic Drilling unit Drilling tools available Horizontal drilling spindles: 4 Vertical drilling spindles: 12 Tool changer positions: 12 MACHINE DETAILS Controlled axes: 4 Software: WoodFlash Voltage: 400 V Current consumption: 40 A Connected load: 18 kW Njdszrmuvspfx Aazjlg Dimensions & Weight Dimensions (L x W x H): 6,250 x 3,494 x 2,300 mm Shipping dimensions (L x W x H): 5,300 x 2,350 x 2,400 mm Shipping weight: 4,000 kg Shipping packages: 2 EQUIPMENT Sawing unit Vacuum pump Becker PICCHIO 2200, year of manufacture 2022 Safety light curtain Manual control panel Tools CNC documentation with user keys/licenses and USB stick Documentation CE marking

Condition: used, Year of construction: 1998, WEEKE BP 150/K Manufacturer: WEEKE Type: BP 150/K Year of construction: 1998 Machine type: CNC machining center / Point-to-point cantilever machine Working area X approx. 3,645 mm* Working area Y approx. 1,250 mm* Working area Z approx. 250 mm* 1 main spindle power: 10 kW Main spindle speed max. 24,000 rpm Tool holder: HSK-F63 Tool changer: 8-position 4th axis 30 vertical drilling spindles 6 horizontal drilling spindles Njdpfezvbhrox Aazslg Table system: Console table Number of consoles: 8 Vacuum pump Safety device Control system: HOMAG HOMATIC 2000 / HOMATIC 2000 IPC* Software: HOMAG woodWOP 4.5 4th axis: C-axis / NC-controlled auxiliary axis*

Condition: used, Year of construction: 2005, Second-hand machine Year of manufacture: 2005 Features and technical specifications: - Cantilever machine (6 units) - Travel dimensions: X = 3,490 mm Y = 1,690 mm Z = 205 mm - Machining dimensions: X = 3050 mm Y = (Max. milling depth – tool radius) 1,345 mm Z = 150 mm - TF 20 drilling head - Power 2.2 kW - 8 vertical spindles, spindle spacing 32 mm in the X direction - 6 vertical spindles, spindle spacing 32 mm in the Y-axis - 2+2 horizontal spindles in the X-axis - 1+1 horizontal spindles in Y-axis - with integrated 120 mm grooving saw blade - with 9.2 kW electric milling spindle with ISO 30 mount Nlodszk Nz Aopfx Aazog - with C-axis - with angle unit - with 12-position tool changer - with tool change station for angle units - with vacuum pump 80–100 m³/h - Total connected load 16 kW - Compressed air 6 bar - Compressed air consumption 210 NL/m - Extraction connection 250 mm - Extraction volume 5,300 m³/h - Extraction velocity 30 m/sec - Dimensions: 5940 x 3800 x 2510 mm - Weight: 3,700 kg Availability: at short notice Location: 63934 Röllbach

Condition: used, Year of construction: 2014, Used Machine Year of Manufacture: 2014 Features and Technical Specifications: - X-axis working range: 3,740 mm - Y-axis working range: 1,570 mm - Z-axis travel: 350 mm Nodpjzlbp Ujfx Aazolg - 4th axis: available - 5th axis: 5-axis spindle, 12 kW motor - with additional locking mechanism for the C-axis - Tool change stations: 24 with turret changer; 10 on the left side of the machine column - Vertical drilling spindles: 12 - Machine table: cantilever table - Automatic table positioning: available - 6 e-motion workpiece supports - Special workpiece clamping system for frames - Software: FORMAT 4 WOOD FLASH, TPA ALBATROS - 2 machining areas for alternating setup - With automatic central lubrication - With mobile control console featuring a PC monitor - With air conditioning for the control cabinet - With a 90 m³/h vacuum pump - With handheld control unit - Includes: 12 frame clamps, 8 large and 4 medium suction cups

Year of construction: 2021, condition: used, Tube manufacturing line Manufacturer: Bazhou Wanxin Industrial and Trading Tube manufacturing line consisting of: Double-station unwinding device Function: Unwinds the coil passively Design: 2-station design with 180-degree rotation, manual expansion Advantages: Fast loading, simple and convenient operation Hydraulic shear and butt welding machine Function: Cuts off the front and rear ends, centers the strip, and welds the strip back together Design: Manual hydraulic shear with cantilever, front and rear pressure rollers, front and rear centering rollers, welding device Cutting method: hydraulic shear Press material method: double-cylinder press Welding method: manual welding Strip storage device Function: To ensure continuous production of the welded tube, a storage unit must be installed after the shear and butt welding platform so that the storage unit can continuously feed the strips while the strip steel material is prepared for stacking, unwinding, butt cutting, and welding. Design: Frame type, with moving and fixed frames (including feeding device) Feeding speed: max. 120 m/min Storage speed: max. 200 m/min Length of stored strips: 200 - 400 m Pinch roller motor: AC 11 kW Forming and sizing machine Working height: +850 mm Power: AC/DC motor: 160 kW, 1000 - 2000 rpm Reducer: Gear hardening Arrangement: Passive five-roll straightening machine, vertical rolls for feeding material, forming through 7 horizontal roll stands and 8 vertical roll stands, guiding, pressing, deburring, cooling, and sizing through 6 horizontal roll stands and 5 vertical roll stands, 1 round sizing stand Round sizing stand: 1 set of smoothing device, two sides with 8 rolls each, 4 rolls per side. 30 mm, 40cr, quenching, tempering, and hardening Horizontal roll shaft: 60 mm, bearing at position 55, made of material 40Cr Heat treatment of horizontal roll: surface hardening, HRC 50-55 Bearing guide: forged steel 45# Vertical roll shaft: 40 mm, material 40Cr, quenched, tempered, and hardened Vertical and horizontal rolls - Design: Portal design, opening width: 120 mm, clamping of horizontal roll stand: adjustment via worm gear Material of horizontal and vertical roll stands: welded (aging annealing) Gearbox: Gear: Spiral bevel gear Shaft of pinch roll: 50 mm, 2 rolls for pinching, adjusted via a manual screw rod Guide shaft: 40 mm Deburring knife: 2 pcs., one for working and one as a spare Cooling tank Cold cut-off saw Nedpfx Aszuz H Ssazelg Function: The cold cut-off saw is one of the most important machines in the ERW tube line. It can cut the tubes to the preset length during high-speed production. Type: KK-5-50 Tube diameter: Round tubes 16-63.5 mm and corresponding square and rectangular tubes Length cut: any length between 1 - 6 m Material thickness: 0.6-2.5 mm Drive motor: 11 kW servo Yaskawa Feeding motor: 2.9 kW serco Yaskawa Saw motor: 11 kW, AC motor with frequency converter Feeding method: Servo multi-stage speed feed Speed adjustment: max. 110 m/min Clamping force: pneumatic Drag chain Saw blade: 400 mm Saw gearbox model: KK-80 Saw stroke (device length): 3 m Device dimensions: 4500 x 1500 x 1300 mm Conveyor track, table, and packaging machine Function: The formed tubes are automatically removed from the roll.

Condition: like new (used), Year of construction: 2022, operating hours: 454 h, load capacity: 1,500 kg, lifting height: 5,400 mm, fuel type: electric, mast type: triplex, construction height: 2,400 mm, Manufacturer + model: ACTIL N 15 S - TTFY Mast: 3F5400 ID: 26064.0363 Category: Demo Mast: 3F5400 Lowered height: 2400 mm Lifting height: 5400 mm Capacity: 1500 kg Year: 2022 Hours: 454 hours Capacity: 24V / 775Ah Options: DEMO!! MINI forklift - Order picker - Counterbalance stacker (3-in-1!!) - Dual controls - Triplex mast Nljdpfxjzv R Dcs Aazog - FFL mast - Stainless steel and fork spreader - Tilting fork carriage - Spotlights - 2 x Blue Spot lights - with cantilevered forks - SUITABLE for all types of pallets - POWER STEERING

Condition: like new (used), Year of construction: 2018, operating hours: 214 h, load capacity: 2,000 kg, lifting height: 4,000 mm, fuel type: electric, mast type: triplex, construction height: 1,920 mm, Manufacturer + model: LINDE L 20 AS (1173) *EX* Proplan 2GD / Zone 1-21-22 * Mast: 3F4000 ID: 26064.5442 Cat.: Demo Mast: 3F4000 Lowered height: 1920 mm Lifting height: 4000 mm Capacity: 2000 kg Nlodozv R Arepfx Aazjg Year: 2018 Hours: 214 hours Capacity: Complete NEW * 24V / 315Ah * Year of manufacture 2025 Options: *EX* Proplan !!!!! System / Certificate = EPS 16 ATEX 1137 X Gas group = IIB Type = Cat 2G (allowed in ZONE 1 and 2) Temperature class = T4 ===== Dust group = IIIC Type = Cat 2D (allowed in ZONE 21 and 22) Temperature class = T 120*C ===== Very UNIQUE explosion-proof ATEX “DEMO” wide-track forklift - with cantilevered, adjustable forklift forks - also equipped with ADJUSTABLE support legs POWER STEERING – Complete, LIKE NEW!!

Condition: like new (used), Year of construction: 2019, operating hours: 148 h, load capacity: 1,000 kg, lifting height: 3,250 mm, fuel type: electric, mast type: duplex, construction height: 2,190 mm, Manufacturer + model: ACTIL N 10 S - TFY Mast: 2F3250 ID: 23093.0147 Category: Demo Nlsdpfx Aezv Rvxeazjg Mast: 2F3250 Lowered height: 2019 mm Lifting height: 3250 mm Capacity: 1000 kg Year: 2019 Hours: 148 hours Capacity: 24 V / 775 Ah Options: DEMO!! 3-in-1!! MINI forklift - Order picker - Counterbalance stacker Fully equipped: - Dual steering - Duplex FFL mast - With cantilever-style adjustable forklift forks - SUITABLE for all types of pallets POWER STEERING

Condition: new, Year of construction: 2020, operating hours: 45 h, load capacity: 1,300 kg, lifting height: 4,500 mm, fuel type: electric, mast type: triplex, construction height: 2,140 mm, Manufacturer + model: GENKINGER EGP 13/44 So = part of HUBTEX!! Mast: 3F4500 ID: 24053.0388 Condition: New Mast: 3F4500 Forks: 1200/2000 mm Nledpfx Aozv H R Eoazeg Lowered height: 2140 mm Lifting height: 4500 mm Capacity: 1300 kg Year: 2020 Hours: 45 hours Capacity: 24 V / 345 Ah Options: VERY unique SPECIAL build, WIDE TRACK!!! - LIFTING CAPACITY 1300 KG @ 1200 MM - Equipped with a spreader!! - VETTER quick-release forks 1200 -> 2000 mm!! - PROPORTIONAL lifting and lowering valves - With cantilevered forks - SUITABLE for all types of pallets - Width between support legs 1340 MM!! POWER STEERING, in complete LIKE NEW condition!!

Condition: like new (used), Year of construction: 2017, operating hours: 41 h, load capacity: 1,600 kg, lifting height: 2,850 mm, fuel type: electric, mast type: duplex, construction height: 1,920 mm, Options: VERY unique CONTRA stacker! Equipped with: - MAST with tilt function - CANTILEVER adjustable forklift forks - SUITABLE for all types of pallets Nedpszv H Rxjfx Aazelg - POWER STEERING!!!

Condition: new, Year of construction: 2026, functionality: fully functional, 50 linear meters of Nedcon pallet racking 🧰 Product features • Manufacturer: NEDCON • Color: galvanized / blue / orange • Condition: new, see photos • Frames: 19 units, pre-assembled 700 x 110 cm • Beams: 144 units with 270 cm clear span, box profile 110 x 40 mm • Safety: 288 units of galvanized safety pins • Fasteners: 76 units of Hilti concrete anchors • Load capacity: 3,050 kg per level • Field load: 12,000 kg • Load capacity label: included Over 5,000 linear meters in stock Frame heights up to 7 meters Available beam lengths: 182.5, 270, 330 and 360 cm Matching deep uprights, shelf liners and shelf panels available upon request 💰 Price: €10,490 net, excluding VAT • Quantity discount: available upon request • Shipping costs: available upon request, throughout Europe • Delivery time: Immediately available • Inspection and collection: possible at any time by appointment • Product number: P2837 Constantly over 5,000 linear meters of pallet racking from numerous manufacturers in stock (Subject to changes and errors in technical data, specifications and prices, as well as prior sale! See our terms and conditions, all prices excl. VAT, ex warehouse.) Lenox Trading – Top warehouse technology & used & new heavy-duty racking Description: Are you looking for high-quality warehouse racking for sale? With around 100 employees, Lenox Trading is one of the largest dealers of new and used warehouse technology in the DACH region (Austria, Germany, Switzerland). ⚡ IMMEDIATELY AVAILABLE: • Over 10,000 linear meters of racking immediately available • 20,000 m² of mezzanine floors & steel platform structures immediately available • Weekly, 30–50 semi-trailer trucks of goods turnover for maximum selection 📦 OUR RANGE (BUY CHEAP ONLINE): Whether pallet racking, heavy-duty racking, high-bay racking, shelving, tire racking or racking for IBC containers – we deliver and install throughout Europe with our OWN team! Including CAD planning, transport, dismantling and assembly. 🏭 TOP BRANDS USED & FROM INSOLVENCY / BANKRUPTCY LIQUIDATION: • SSI Schäfer (Schäfer Lagertechnik, R 3000, PR 600, PR 300) • Jungheinrich (Type MPB, Type E, Jungheinrich heavy-duty racking) Njdpfx Aasfkgq Sjzolg • Cantilever racking (Elvedi cantilever racking, Schäfer, Ohra) • Stow, Meta, Bito, Galler, Nedcon, Voest (Vöst), SLP, Palflex, Ramada, Bauer, Ohrner 🔨 OUR SECOND PILLAR: ONLINE AUCTIONS & LIQUIDATION For dismantling and clearing orders, we offer a complete, all-round service package: 1. Fixed-price purchase: Purchase of merchandise, equipment & complete stock, including complete clearing. 2. Commission-based auction: Conducting auctions on behalf of clients. Our full service provided by our own employees: cataloging, office preparation, inspection, goods dispatch, logistics, dismantling and complete handover. Whether you found us through heavy-duty racking or are looking for galvanized heavy-duty racking / heavy-duty racking system, we guarantee the best conditions. Contact us for a non-binding offer!

Year of construction: 2026, condition: new, functionality: fully functional, overall weight: 120 kg, laser power: 30 W, laser wavelength: 1,064 nm, scan area length: 150 mm, scan area width: 150 mm, type of cooling: air, type of input current: AC, laser type: fiber laser, The universal LAS 28 XLe laser marking system from Systemtechnik Hölzer GmbH can be used for a very wide range of marking applications. With the integrated fiber laser, you can mark almost all materials such as steel, hard metal, aluminium and plastics. Depending on requirements, the system can be equipped with a 20, 30 or 50 watt fiber laser. For permanent marking, the use of a laser has become indispensable in many industries. With the powerful laser software, texts, numbers, 2D codes, QR codes and logos can be created with just a few clicks and without extensive programming knowledge. The software automatically counts up serial and article numbers once they have been set. In addition, the software can read data (variable information such as drawing numbers, project designations, etc.) from existing tables and automatically transfer it to predefined areas. The use of a hand scanner is also possible. The standard equipment includes an integrated PC with Windows operating system and laser software. The LAS 28 XLe laser model can optionally be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Other options, such as lateral cantilevers for marking long parts, movable Z-axis, drawer systems, etc., can also be implemented. Programmable, software-controlled axes (X-, Y-, Z-axis) and database connection are also possible. Made in Germany Fiber laser 30W, 20 W or 50 Watt - Laser class 1 Nledewkpvvspfx Aazeg - Wavelength 1064nm - Marking field size 150x150mm (optionally larger) - marking software EZCAD in German / English - optional: rotary axis (3-jaw chuck) - optional: digital height measuring system - optional: exhaust system (incl. activated carbon filter) - optional: autofocus system - system for automatically determining the focus distance - pilot laser (simple preview, contour preview) - focus finder (simple focus adjustment) - signal light for indication of operating status - max. component height approx. 300mm - electrically adjustable Z-axis - Integrated PC with Windows operating system - frame made of aluminum profile - air cooled - Door width approx. 700mm / door height(pass-through): 400mm - Connection 230V - Dimensions: approx. 900 x 800 x 1900 mm (LxWxH) - Weight: approx. 120 Kg

Year of construction: 2025, condition: new, functionality: fully functional, The universal laser marking system LAS 28 from Systemtechnik Hölzer GmbH can be used for a very wide range of marking applications. With the integrated fiber laser you can mark almost all materials such as steel, carbide, aluminum and plastics. Depending on the requirements, the system can be equipped with a 20, 30 or 50 watt fiber laser. For permanent marking, the use of the laser is necessary in many industries. With the powerful laser software, texts, numbers, 2D codes, QR codes and logos can be realized with just a few clicks without extensive programming knowledge. Serial and article numbers are automatically incremented by the software after prior setting. In addition, the software can read data (variable information such as drawing numbers, project designations, etc.) from existing tables and automatically transfer them to predefined areas. The use of a hand scanner is also possible. The standard equipment includes a laptop incl. holder with Windows operating system. Optionally, the laser model LAS 28 can be equipped with a rotary axis (3-jaw chuck) for marking cylindrical parts. Further options, such as lateral cantilevers for marking long parts, can be realized. Made in Germany - Fiber laser 20W (Optional: 30W, 50W) - Wavelength 1064nm - marking field size 150x150mm (optional: 200x200) - optional: rotary axis (3-jaw chuck) - optional: digital height measuring system Nljdot Dig Espfx Aazjg - optional: exhaust system (incl. activated carbon filter) - optional: autofocus function for automatic determination of the focus distance - marking software EZCAD - Pilot laser (simple preview, clear text preview) - focus finder (easy focus adjustment) - max. part height approx. 270mm - electrically adjustable Z-axis (adjustment of working plane) - frame made of aluminum profile - connection 230V - air cooled - Laptop with operating system Windows - dimensions: 800x 600 x 1660mm (LxWxH) - Weight: approx. 80 Kg

Condition: used, Winding and unwinding mandrel OBRU, type HM Order number 66239, year of manufacture approx. 1970 Coil weight 80 kg Coil width max. 200 mm Coil inner diameter 270 - 450 mm Coil outer diameter max. 650 mm Center of mandrel shaft to mandrel base 720 mm Mandrel speed 16 rpm Motor power 0.18 kW Mains connection 380 volts, 50 Hz - Coil support by 4 cantilever bolts Nedpszt U Iysfx Aazolg - Central spreading of the 4 support bolts via eccentric rotating lever - Gear drive via geared motor - Mechanically adjustable slip clutch - Height adjustable by clamping to the support column - Motor circuit breaker Dimensions L x W x H 960 x 650 x 1100 mm Weight 110 kg Good condition

Condition: ready for operation (used), Year of construction: 2018, total height: 2,414 mm, total width: 1,110 mm, travel distance X-axis: 500 mm, travel distance Y-axis: 580 mm, travel distance Z-axis: 500 mm, overall weight: 800 kg, product length (max.): 1,266 mm, number of axes: 3, This 3-axis Hexagon Tigo SF 05.06.05 was manufactured in 2018. It features a measuring volume of 500 x 580 x 500 mm and a granite measuring plate with high-precision linear ball bearing guideways. The machine supports a maximum workpiece weight of 150 kg and operates without the need for compressed air. If you are looking to get high-quality measurement capabilities, consider the Hexagon Tigo SF 05.06.05 CMM machine we have for sale. Contact us for further details. Nledpfxezufkbs Aazsg - Machine Structure: Cantilever design with steel frame construction- Overall Dimensions (X x Y x Z): 1110 x 1266 x 2414 mm- Table Specifications: Granite measuring plate (fixed desk) with M8 x 1.25 threaded inserts, flatness according to DIN 876/II- Guideways: High-precision linear ball bearing guideways- Measuring System: METALLUR scale, resolution 0.039 µm- Pinion/Ram Counterbalance: Steel spring- Max. Workpiece Weight: 150 kg- Compressed Air Requirements: No compressed air required (does not require compressed air, meaning no air compressor is needed!)- Dynamics (3D Speed): Max. 520 mm/s- Dynamics (3D Acceleration): Max. 1750 mm/s²- Scanning Speed: Max. 300 mm/s- Temperature Range for Guaranteed Uncertainty: 15 to 30 °C- Operating Temperature Range: 10 to 45 °C- Relative Humidity: 40% - 70% non-condensing- Temperature Compensation: Multi-sensor temperature compensation technology- Probe / Sensor Systems Compatibility: Equipped with LSP-X1c touch probe system (Max. probe weight: 33g; Max. probe length: Axial 125 mm, Lateral 60 mm); also compatible with TESASTAR-m M8 / TESASTAR-mp- Controller & Operating System: All-in-one system with integrated PC and controller in the base, adjustable arm mount for screen, keyboard, and lightweight jogbox- Advanced Software Modes: Fly2 Mode (trajectory optimization), Eco Mode (automatic shutdown)

Condition: like new (used), Year of construction: 2018, operating hours: 183 h, load capacity: 1,200 kg, lifting height: 3,300 mm, fuel type: electric, mast type: duplex, construction height: 2,200 mm, Options: VERY unique CONTRA stacker!! Fully equipped! Features: FFL mast = Full Free Lift, side shift, mast tilt, pantograph, extra wide fork carriage; width = 1230 mm, blue spot & strobe light, lateral battery change system, with cantilever adjustable forklift forks, suitable for all types of pallets, power steering, complete and LIKE NEW! Nsdpfxezuubij Aazolg